User`s Manual
WT-2000AP
Turbo-G Wireless AP
User’s Manual
1
AirLive WT-2000AP User’s Manual
Copyright
The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an
information retrieval system, translated into any language, or transmitted in any form or by any means,
mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written
permission.
Trademarks
All products, company, brand names are trademarks or registered trademarks of their respective companies. They
are used for identification purpose only. Specifications are subject to be changed without prior notice.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against radio interference in a
commercial environment. This equipment can generate, use and radiate radio frequency energy and, if not
installed and used in accordance with the instructions in this manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause interference, in which case
the user, at his own expense, will be required to take whatever measures are necessary to correct the interference.
CE Declaration of Conformity
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022/A1 Class B.
The specification is subject to change without notice.
2
AirLive WT-2000AP User’s Manual
Table of Contents
Chapter 1 Introduction .............................................................................. 4
Functions and Features......................................................................... 4
Packing List.......................................................................................... 5
Chapter 2 Hardware Installation ............................................................... 6
2.1 Panel Layout................................................................................... 6
2.2 Procedure for Hardware Installation .............................................. 8
Chapter 3 Network Settings and Software Installation ............................. 9
3.1 Make Correct Network Settings of Your Computer....................... 9
Chapter 4 Configuring Wireless Access Point........................................ 10
4.1 Start-up and Log in....................................................................... 11
4.2 Status ............................................................................................ 12
4.3 View Log ...................................................................................... 12
4.4 Client List..................................................................................... 13
4.5 Wizard .......................................................................................... 13
4.6 Basic Setting................................................................................. 15
4.7 Advanced Settings ........................................................................ 25
4.8 Maintenance ................................................................................. 26
Appendix A TCP/IP Configuration for Windows 95/98......................... 29
Appendix B 802.1x Setting ..................................................................... 35
Appendix C WDS Setting ....................................................................... 40
Appendix D FAQ and Troubleshooting .................................................. 45
How do I connect AP by using wireless? ..................................... 45
3
AirLive WT-2000AP User’s Manual
C
Chhaapptteerr 11 IInnttrroodduuccttiioonn
Congratulations on your purchase of this outstanding AirLive Wireless AP
This product is specifically
designed for Small Office and Home Office needs. Instructions for installing and configuring this product can be
found in this manual. Before you install and use this product, please read this manual carefully for fully
exploiting the functions of this product.
Functions and Features
AP Basic functions
z
Auto-sensing Ethernet Switch
Equipped with a 4-port auto-sensing Ethernet switch.
z
DHCP server supported
All of the networked computers can retrieve TCP/IP settings automatically from this product.
z
Web-based configuring
Configurable through any networked computer’s web browser using Netscape or Internet Explorer.
Wireless functions
z High speed for wireless LAN connection
Up to 54Mbps data rate by incorporating Orthogonal Frequency Division Multiplexing (OFDM).
z Roaming
Provides seamless roaming within the IEEE 802.11b (11M) and IEEE 802.11g (54M) WLAN
infrastructure.
z IEEE 802.11b compatible (11M)
Allowing inter-operation among multiple vendors.
z IEEE 802.11g compatible (54M)
Allowing inter-operation among multiple vendors.
z Auto fallback
54M, 48M, 36M, 24M, 18M, 12M, 6M data rate with auto fallback in 802.11g mode.
11M, 5.5M, 2M, 1M data rate with auto fallback in 802.11b mode.
Security functions
z 802.1X supported
When the 802.1X function is enabled, the Wireless user must authenticate to this router first to use the
Network service.
z Support WPA-PSK and WPA version 1 and 2
When the WPA function is enabled, the Wireless user must authenticate to this router first to
4
AirLive WT-2000AP User’s Manual
use the Network service
Advanced functions
z System time Supported
Allow you to synchronize system time with network time server.
Packing List
z
z
Wireless AP unit
Installation CD-ROM
z
Power adapter
z
CAT-5 UTP Fast Ethernet cable
5
AirLive WT-2000AP User’s Manual
C
Chhaapptteerr 22 H
Haarrddw
waarree IInnssttaallllaattiioonn
2.1 Panel Layout
2.1.1. Front Panel
Figure 2-1 Front Panel
LED: Ports:
Port
Description
PWR
Power inlet
Port 1-4
the ports where you will connect networked computers and other
devices.
6
AirLive WT-2000AP User’s Manual
2.1.2. Rear Panel
Figure 2-2 Rear Panel
LED:
LED
Power
Status
WLAN
Link.
1~4
Function
Power
indication
System
status
Wireless
activity
Color
Status
Description
Green
On
Power is being applied to this product.
Green
Blinking
Green
Link status Green
10/100
The WAN port is sending or receiving data.
Blinking
Sending or receiving data via wireless
On
Data Rate Green
On
Reset
alive.
Blinking
Blinking
Speed
Status is flashed once per second to indicate system is
An active station is connected to the corresponding
LAN port.
The corresponding LAN port is sending or receiving
data.
Data is transmitting in 100Mbps on the corresponding
LAN port.
To reset system settings to factory defaults
7
AirLive WT-2000AP User’s Manual
2.2 Procedure for Hardware Installation
2. Decide where to place your Wireless Access Point
You can place your Wireless Access Point on a desk or other flat surface, or you can mount it on a wall. For
optimal performance, place your Wireless Access Point in the center of your office (or your home) in a
location that is away from any potential source of interference, such as a metal wall or microwave oven.
This location must be close to power and network connection.
2.
Setup LAN connection
a. Wired LAN connection: connects an Ethernet cable from your computer’s Ethernet port to one of the
LAN ports of this product.
b. Wireless LAN connection: locate this product at a proper position to gain the best transmit performance.
Figure 2-3 Setup of WLAN and LAN connections for this product.
4.
Power on
Connecting the power cord to power inlet and turning the power switch on, this product will automatically
enter the self-test phase. When it is in the self-test phase, the indicators M1 will be lighted ON for about 10
seconds, and then M1 will be flashed 3 times to indicate that the self-test operation has finished. Finally, the
M1 will be continuously flashed once per second to indicate that this product is in normal operation.
8
AirLive WT-2000AP User’s Manual
C
Chhaapptteerr 33 N
waarree IInnssttaallllaattiioonn
Neettw
woorrkk SSeettttiinnggss aanndd SSooffttw
To use this product correctly, you have to properly configure the network settings of your computers and install
the attached setup program into your MS Windows platform (Windows 95/98/NT/2000).
3.1 Make Correct Network Settings of Your Computer
The default IP address of this product is 192.168.1.254, and the default subnet mask is 255.255.255.0. These
addresses can be changed on your need, but the default values are used in this manual. If the TCP/IP
environment of your computer has not yet been configured, you can refer to Appendix A to configure it. For
example,
1. configure IP as 192.168.1.1, subnet mask as 255.255.255.0 and gateway as 192.168.1.254, or more
easier,
2. configure your computers to load TCP/IP setting automatically, that is, via DHCP server of this product.
After installing the TCP/IP communication protocol, you can use the ping command to check if your computer
has successfully connected to this product. The following example shows the ping procedure for Windows 95
platforms. First, execute the ping command
ping 192.168.1.254
If the following messages appear:
Pinging 192.168.1.254 with 32 bytes of data:
Reply from 192.168.1.254: bytes=32 time=2ms TTL=64
a communication link between your computer and this product has been successfully established. Otherwise, if
you get the following messages,
Pinging 192.168.1.254 with 32 bytes of data:
Request timed out.
There must be something wrong in your installation procedure. You have to check the following items in
sequence:
1.
Is the Ethernet cable correctly connected between this product and your computer?
Tip: The LAN LED of this product and the link LED of network card on your computer must be lighted.
2.
Is the TCP/IP environment of your computers properly configured?
Tip: If the IP address of this product is 192.168.1.254, the IP address of your computer must be
192.168.1.X and default gateway must be 192.168.1.254.
9
AirLive WT-2000AP User’s Manual
C
Chhaapptteerr 44 C
Coonnffiigguurriinngg W
Wiirreelleessss A
Acccceessss PPooiinntt
This product provides Web based configuration scheme, that is, configuring by your Web browser, such as
Netscape Communicator or Internet Explorer. This approach can be adopted in any MS Windows, Macintosh or
UNIX based platforms.
10
AirLive WT-2000AP User’s Manual
4.1 Start-up and Log in
Activate your browser, and disable the proxy or add the IP address of this product into the exceptions. Then,
type this product’s IP address in the Location (for Netscape) or Address (for IE) field and press ENTER. For
example: http://192.168.1.254.
After the connection is established, you will see the web user interface of this product. There are two
appearances of web user interface: for general users and for system administrator.
A window would pop-up asking for Login and Password. Please enter “admin” for login, and “airlive” for
password.
11
AirLive WT-2000AP User’s Manual
4.2 Status
This option provides the function for observing this product’s working status:
A. Wireless MAC Address: display the MAC address of this Wireless Access Point.
B. Network ID (SSID):
The SSID is the network name used to identify a wireless network. The SSID must be the same for all
devices in the wireless network (i.e. in the same BSS). Several access points on a network can have
the same SSID. The SSID length is up to 32 characters. The default SSID is “airlive”.
C. Channel: display the Channel number of this Wireless Access Point
D. Security Type: shows Wireless Security type information
4.3 View Log
Click the View Log button on System Status Page You can see the access logs from this screen also you can
download the logs and save to your computer.
12
AirLive WT-2000AP User’s Manual
4.4 Client List
You can see the DHCP client information include Client IP,Host Name, Client’s MAC address,
administrator can select the client and do wake up and Delete actions, before you click the Wake Up
button, just make sure the network adapter of the machine support wake on LAN function and turn it on.
then just workable.
4.5 Wizard
Setup Wizard will guide you through a basic configuration procedure step by step. Press
Setup Wizard – LAN IP Address:
”Next >”
enter the IP address of this machine.
13
AirLive WT-2000AP User’s Manual
Setup Wizard – Wireless Setting : for details , please read the Basic Setting Æ Wireless.:
Setup Wizard – Configuration is Completed :
14
save and Reboot this machine
AirLive WT-2000AP User’s Manual
4.6 Basic Setting
Basic Setting have Primary Setup, DHCP Server, and Wireless setting functions.
4.6.1 Primary Setup – LAN IP Address
Entering the IP Address: default ip is 192.168.1.254, you can change ip address in this field and
Press “Save”
4.6.2 DHCP Server
The settings of DHCP server include the following items:
1.
DHCP Server: Choose “Disable” or “Enable.”
2.
IP pool starting Address/ IP pool ending Address: Whenever there is a request, the DHCP
server will automatically allocate an unused IP address from the IP address pool to the requesting
computer. You must specify the starting and ending address of the IP address pool.
15
AirLive WT-2000AP User’s Manual
3.
Domain Name: Optional, this information will be passed to the client.
press “More>>” button into the other settings :
4.
Primary DNS/Secondary DNS: This feature allows you to assign DNS Servers
5.
Primary WINS/Secondary WINS: This feature allows you to assign WINS Servers
6.
Gateway: The Gateway Address would be the IP address of an alternate Gateway.
This function enables you to assign another gateway to your PC, when DHCP server
offers an IP to your PC.
press “Client List >” button into client list page
16
AirLive WT-2000AP User’s Manual
4.6.3 Wireless Setting, 802.1X setting and WDS
Wireless settings allow you to set the wireless configuration items.
1.
Wireless : The user can enable or disalbe wireless function.
2.
Network ID (SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can
roam freely over this product and other Access Points that have the same Network ID. (The factory setting is
“default”)
3.
Channel: The radio channel number. The permissible channels depend on the Regulatory Domain.
The factory setting is as follow: channel 6 for North America; channel 7 for European (ETSI); channel 7
for Japan.
4.
WEP Security: Select the data privacy algorithm you want. Enabling the security can protect your data
while it is transferred from one station to another. The standardized IEEE 802.11 WEP (128 or 64-bit) is
used here.
5.
WEP Key 1, 2, 3 & 4: When you enable the 128 or 64 bit WEP key security, please select one WEP key to
be used and input 26 or 10 hexadecimal (0, 1, 2…8, 9, A, B…F) digits.
6.
Pass-phrase Generator: Since hexadecimal characters are not easily
remembered, this device offers a conversion utility to convert a simple
word or phrase into hex.
17
AirLive WT-2000AP User’s Manual
6. 802.1X Setting
802.1X
Check Box was used to switch the function of the 802.1X. When the 802.1X function is enabled, the Wireless
user must authenticate to this router first to use the Network service.
RADIUS Server
IP address or the 802.1X server’s domain-name.
RADIUS Shared Key
Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the
RADIUS server.
WPA-PSK
1. Select Encryntion and Preshare Key Mode
If you select HEX,you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII,the length of preshare key is from 8 to 63.
2. Fill in the key, Ex 12345678
18
AirLive WT-2000AP User’s Manual
WPA
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the Wireless user
must authenticate to this router first to use the Network service. RADIUS Server
IP address or the 802.1X server’s domain-name.
Select Encryption and RADIUS Shared Key
If you select HEX,you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII,the length of preshare key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the
RADIUS server.
WPA2-PSK(AES)
19
AirLive WT-2000AP User’s Manual
1. Select Pre-share Key Mode
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of Pre-share key is from 8 to 63.
2. Fill in the key, Ex 12345678
WPA2(AES)
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the
Wireless user must authenticate to this router first to use the Network service. RADIUS Server
IP address or the 802.1X server’s domain-name.
Select RADIUS Shared Key
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of Pre-share key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key value
in the RADIUS server.
WPA-PSK /WPA2-PSK
The router will detect automatically which Security type(Wpa-psk version 1 or 2) the client
uses to encrypt.
1. Select Pre-share Key Mode
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
20
AirLive WT-2000AP User’s Manual
If ASCII, the length of Pre-share key is from 8 to 63.
2. Fill in the key, Ex 12345678
WPA/WPA2
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the
Wireless user must authenticate to this router first to use the Network service. RADIUS Server
The router will detect automatically which Security type(Wpa-psk version 1 or 2) the client
uses to encrypt.
IP address or the 802.1X server’s domain-name.
Select RADIUS Shared Key
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of Pre-share key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key value
in the RADIUS server.
21
AirLive WT-2000AP User’s Manual
WDS(Wireless Distribution System)
WDS operation as defined bythe IEEE802.11 standard has been made available. Using WDS it is possible to
wirelessly connect Access Points, and in doing so extend a wired infrastructure to locations where cabling is not
possible or inefficient to implement.
22
AirLive WT-2000AP User’s Manual
4.6.4 MAC Address Control (Basic SettingÆ Wireless Setting)
MAC Address Control allows you to assign different access right for different users and to assign a specific IP
address to a certain MAC address.
MAC Address Control Check “Enable” to enable the “MAC Address Control”. All of the settings in this
page will take effect only when “Enable” is checked.
Connection control
Check "Connection control" to enable the controlling of which wired and wireless
clients can connect to this device. If a client is denied to connect to this device, it
means the client can't access to the Internet either. Choose "allow" or "deny" to
allow or deny the clients, whose MAC addresses are not in the "Control table"
(please see below), to connect to this device.
Association control
Check "Association control" to enable the
controlling of which wireless client can
associate to the wireless LAN. If a client is
denied to associate to the wireless LAN, it
means the client can't send or receive any data
via this device. Choose "allow" or "deny" to
allow or deny the clients, whose MAC
addresses are not in the "Control table", to
associate to the wireless LAN.
Control table
23
AirLive WT-2000AP User’s Manual
"Control table" is the table at the bottom of the "MAC Address Control" page.
Each row of this table indicates the MAC address and the expected IP address
mapping of a client. There are four columns in this table:
MAC Address
MAC address indicates a specific client.
IP Address
Expected IP address of the corresponding
client. Keep it empty if you don't care its IP
address.
C
When "Connection control" is checked,
check "C" will allow the corresponding client
to connect to this device.
A
When "Association control" is checked,
check "A" will allow the corresponding client
to associate to the wireless LAN.
In this page, we provide the following Combobox and button to help you to input the MAC address.
You can select a specific client in the “DHCP clients” Combobox, and then click on the “Copy to” button to copy
the MAC address of the client you select to the ID selected in the “ID” Combobox.
Previous page and Next Page
To make this setup page simple and clear, we have divided the “Control table” into several pages.
You can use these buttons to navigate to different pages.
24
AirLive WT-2000AP User’s Manual
4.7 Advanced Settings
4.7.1 System Time
Set Date and Time using PC’s Date and Time
Use PC Date and Time as Machine
Set Date and Time manually
Selected if you want to Set Date and Time manually.
25
AirLive WT-2000AP User’s Manual
4.8 Maintenance
4.8.1 Change Password
You can change Password here. We strongly recommend you to change the system password for security reason.
26
AirLive WT-2000AP User’s Manual
4.8.2 View Log
You can View system log by clicking the View Log button
4.8.3 Firmware Upgrade
You can upgrade firmware by clicking Firmware Upgrade button.
27
AirLive WT-2000AP User’s Manual
4.8.4 Backup Setting
You can backup your settings by clicking the Backup Setting button and save it as a bin file. Once you want to
restore these settings, please click Firmware Upgrade button and use the bin file you saved.
4.8.5 Reset to default
You can also reset this product to factory default by clicking the Reset to default button.
4.8.6 Reboot
You can also reboot this product by clicking the Reboot button.
28
AirLive WT-2000AP User’s Manual
A
Appppeennddiixx A
Wiinnddoow
A T
wss 9955//9988
TC
CPP//IIPP C
Coonnffiigguurraattiioonn ffoorr W
This section introduces you how to install TCP/IP protocol into your personal computer. And suppose you have
been successfully installed one network card on your personal computer. If not, please refer to your network card
manual. Moreover, the Section B.2 tells you how to set TCP/IP values for working with this NAT Router
correctly.
A.1 Install TCP/IP Protocol into Your PC
1.
Click Start button and choose Settings, then click Control Panel.
2.
Double click Network icon and select Configuration tab in the Network window.
3.
Click Add button to add network component into your PC.
4.
Double click Protocol to add TCP/IP protocol.
5.
Select Microsoft item in the manufactures list. And choose TCP/IP in the Network Protocols. Click OK
button to return to Network window.
29
AirLive WT-2000AP User’s Manual
6.
The TCP/IP protocol shall be listed in the Network window. Click OK to complete the install procedure and
restart your PC to enable the TCP/IP protocol.
A.2 Set TCP/IP Protocol for Working with NAT Router
1.
Click Start button and choose Settings, then click Control Panel.
2.
Double click Network icon. Select the TCP/IP line that has been associated to your network card in the
Configuration tab of the Network window.
30
AirLive WT-2000AP User’s Manual
3.
Click Properties button to set the TCP/IP protocol for this NAT Router.
4.
Now, you have two setting methods:
31
AirLive WT-2000AP User’s Manual
a.
Select Obtain an IP address automatically in the IP Address tab.
b.
Don’t input any value in the Gateway tab.
32
AirLive WT-2000AP User’s Manual
c.
Choose Disable DNS in the DNS Configuration tab.
B. Configure IP manually
a.
Select Specify an IP address in the IP Address tab. The default IP address of this product is
192.168.1.254. So please use 192.168.1.xxx (xxx is between 1 and 253) for IP Address field and
255.255.255.0 for Subnet Mask field.
33
AirLive WT-2000AP User’s Manual
b.
In the Gateway tab, add the IP address of this product (default IP is 192.168.1.254) in the New
gateway field and click Add button.
c.
In the DNS Configuration tab, add the DNS values which are provided by the ISP into DNS
Server Search Order field and click Add button.
34
AirLive WT-2000AP User’s Manual
A
Appppeennddiixx B
B 880022..11xx SSeettttiinngg
Figure 1: Testing Environment (Use Windows 2000 Radius Server)
1 Equipment Details
PC1:
Microsoft Windows XP Professional without Service Pack 1.
AMIT 531C Wireless Cardbus:3.0.3.0
Driver version:
PC2:
Microsoft Windows XP Professional with Service Pack 1a or latter.
AMIT 561C Wireless Cardbus:1.0.1.0
Driver version: 1.7.29.0 (Driver date: 10.20.2001)
Authentication Server: Windows 2000 RADIUS server with Service Pack 3 and HotFix Q313664.
Note. Windows 2000 RADIUS server only supports PEAP after upgrade to service pack 3 and
HotFix Q313664 (You can get more information from
http://support.microsoft.com/default.aspx?scid=kb; en-us;313664)
2 DUT
Configuration:
1.Enable DHCP server.
2.LAN IP address: 192.168.1.254/24.
3.Set RADIUS server IP.
4.Set RADIUS server shared key.
35
AirLive WT-2000AP User’s Manual
5.Configure WEP key and 802.1X setting.
The following test will use the inbuilt 802.1X authentication method such as ,EAP_TLS,
PEAP_CHAPv2(Windows XP with SP1 only), and PEAP_TLS(Windows XP with SP1 only) using the
Smart Card or other Certificate of the Windows XP Professional.
3. DUT and Windows 2000 Radius Server Setup
3-1-1. Setup Windows 2000 RADIUS Server
We have to change authentication method to MD5_Challenge or using smart
card or other certificate on RADIUS server according to the test condition.
3-1-2. Setup DUT
1.Enable the 802.1X (check the “Enable checkbox“).
2.Enter the RADIUS server IP.
3.Enter the shared key. (The key shared by the RADIUS server and DUT).
4.We will change 802.1X encryption key length to fit the variable test
condition.
3-1-3. Setup Network adapter on PC
1.Choose the IEEE802.1X as the authentication method. (Fig 2)
Note.
Figure 2 is a setting picture of Windows XP without service pack 1. If users upgrade
to service pack 1, then they can’t see MD5-Challenge from EAP type list any more,
but they will get a new Protected EAP (PEAP) option.
2.Choose MD5-Challenge or Smart Card or other Certificate as the EAP
type.
3.If choosing use smart card or the certificate as the EAP type, we select to
use a certificate on this computer. (Fig 3)
4. We will change EAP type to fit the variable test condition.
36
AirLive WT-2000AP User’s Manual
Figure 2: Enable IEEE 802.1X access control
37
AirLive WT-2000AP User’s Manual
Figure 3: Smart card or certificate properties
4. Windows 2000 RADIUS server Authentication testing:
4.1DUT authenticate PC1 using certificate. (PC2 follows the same test procedures.)
1. Download and install the certificate on PC1. (Fig 4)
2. PC1 choose the SSID of DUT as the Access Point.
3. Set authentication type of wireless client and RADIUS server both to
EAP_TLS.
4. Disable the wireless connection and enable again.
5. The DUT will send the user's certificate to the RADIUS server, and then
send the message of authentication result to PC1. (Fig 5)
6. Windows XP will prompt that the authentication process is success or fail
and end the authentication procedure. ( Fig 6)
7. Terminate the test steps when PC1 get dynamic IP and PING remote host
successfully.
38
AirLive WT-2000AP User’s Manual
Figure 4: Certificate information on PC1
Figure 5: Authenticating
Figure 6: Authentication success
4.2DUT authenticate PC2 using PEAP-TLS.
1. PC2 choose the SSID of DUT as the Access Point.
2. Set authentication type of wireless client and RADIUS server both to
PEAP_TLS.
3. Disable the wireless connection and enable again.
4.The DUT will send the user's certificate to the RADIUS server, and then
send the message of authentication result to PC2.
5. Windows XP will prompt that the authentication process is success or fail
39
AirLive WT-2000AP User’s Manual
and end the authentication procedure.
6. Terminate the test steps when PC2 get dynamic IP and PING remote host
successfully.
Support Type: The AP supports the types of 802.1x Authentication:
PEAP-CHAPv2 and PEAP-TLS.
Note.
1.PC1 is on Windows XP platform without Service Pack 1.
2.PC2 is on Windows XP platform with Service Pack 1a.
3.PEAP is supported on Windows XP with Service Pack 1 only.
4.Windows XP with Service Pack 1 allows 802.1x authentication only when data encryption function is
enable.
A
Appppeennddiixx C
C W
WD
DSS SSeettttiinngg
How to setup and work:
First, check the Wlan-mac address of AP1,AP2 and AP3.Please goto command mode and use
“Arp –a ”.
If you can not find the information of Mac, please make the cable to plug in lan-port of ap and ping the lan ip
address then arp –a. There are some information in the screen. For example:
40
AirLive WT-2000AP User’s Manual
AP 1:
IP:192.168.1.254
AP2:
AP3:
IP:192.168.1.253
IP:192.168.1.252
Mac:00-50-18-00-0f-fe
Mac:00-50-18-00-0f-fd
Mac:00-50-18-00-0f-fc
SSID:Default
SSID:Default
SSID:Default
Channel:11
Channel:11
Channel:11
Dhcp Server:Enable
Blue Line:Wireless
Black Line:Wire
41
AirLive WT-2000AP User’s Manual
If the Settings are ok,the client1 and client2 can get ip from dhcp server of AP1.Then Client1 and
Client2 can get information each other.
AP1 Setting:
AP1ÅÆ AP2(Remote Mac: 00-50-18-00-0f-fd)
AP1ÅÆ AP3(Remote Mac: 00-50-18-00-0f-fc)
42
AirLive WT-2000AP User’s Manual
AP2 Setting:
AP2ÅÆ AP1(Remote Mac: 00-50-18-00-0f-fe)
AP3 Setting
AP3ÅÆ AP1(Remote Mac: 00-50-18-00-0f-fe)
43
AirLive WT-2000AP User’s Manual
44
AirLive WT-2000AP User’s Manual
A
Appppeennddiixx D
D FFA
AQ
Q aanndd T
Trroouubblleesshhoooottiinngg
How do I connect AP by using wireless?
1.How to start to use wireless?
A: First, make sure that you already installed wireless client device in your computer. Then check the
Configuration of wireless router. The default is as below:
About wireless client, you will see wireless icon:
Then click and will see the ap list that wireless client can be accessed:
If the client can not access your wireless router, please refresh network list again. However, I still can not fine
the device which ssid is “default”, please refer to Q3.
45
AirLive WT-2000AP User’s Manual
Choose the one that you will want to connect and Connect:
If successfully, the computer will show
and get ip from router:
2.When I use AES encryption of WPA-PSK to connect even if I input the correct
pre-share key?
A: First, you must check if the driver of wireless client supports AES encryption. Please refer to the below:
46
AirLive WT-2000AP User’s Manual
If SSID is default and click “Properties” to check if the driver of wireless client supports AES encryption.
47
AirLive WT-2000AP User’s Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising