complete setup and programming manual for xt/xtx/xto gprs panels

complete setup and programming manual for xt/xtx/xto gprs panels
Document #2000-XTIN
COMPLETE SETUP AND PROGRAMMING MANUAL
FOR
XT/XTX/XTO GPRS PANELS
*A Videofied CMA / XMB / XMA / WMB Alphanumeric Keypad or Frontel TMT2 is required
for programming and maintenance*
CMA
XMB/XMA
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
WMB
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Table of Contents
Page
FCC Guidelines
3
Basic Guidelines
4
Introduction
5
Initial Programming
6-15
Device Installation
16
Disabling Monitoring
17
Entering Badges and Access Codes
18-19
Choosing Siren Options
19
Testing GPRS Level
20
Enabling External RF Antenna
21
Testing Device RF Level
22
Connecting a GPRS Antenna
23
Power Chart
23
Arming Input Wiring Diagram
24
Testing to Central Station
25
Mounting XT/XTX
26
Mounting XTO
26-27
Programmable Input Configuration
28-30
Programmable Output Configuration
31-33
Configuring Scheduling
34-36
Troubleshooting
37-39
After Initial Programming Flow Chart
40-41
Addendum
Battery Specifications
Finding Manufacture Week/Year
Additional System Quick Codes
Replacing Device and Control Panel batteries
Checking Control Panel Firmware
42-44
42
43
43
44
44
2|Page
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Regulatory Information for USA and Canada
FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI
Video Technologies may void the FCC authorization to operate this equipment.
FCC Part 15.105 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
 Consult the dealer or an experienced radio/TV technician for help.
Radiofrequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
3|Page
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Basic Setup Guidelines for Installation and Programming
Pre-Setup
1) Obtain the account number from the Central Station
2) If using Cellular communication for primary or backup, activate the SIM card through your cellular
provider
a. *Do these steps at least 1 day before the install.
System Programming and Setup
1) Setup and program the system in the office or in your vehicle. DO NOT MOUNT THE DEVICES. (Pages 615)
2) Disable monitoring so that signals are not sent until you are ready to send them. (Page 17)
3) Add user codes and or badges after initial programming. (Pages 18-19)
4) Silence the siren before arming for testing (If siren is present). (Page 19)
Deploying the System on Site
1) Place the panel where you want to mount it and run the GPRS Level Test. You must get a GPRS level of 3/5
or better for reliable transmission. If not, you will need to move the panel and run the test again.* (Page
20)
2) Deploying Devices: Use your keypad to run the RF test for each device. If you get a 9/9 for your RF test on
the first device, then mount it. If not, you will need to move the device to get optimal signal.* (Page 22)
a. If you are not getting an appropriate GPRS or RF level, you can add an external antenna for either
signal. (Not available for the XL600) Enabling External Antenna: (Page 21)
3) Re-enable monitoring before you send signals (Page 17)
a. If you are currently using TMT Installer to program the system you can now take still pictures from
each MotionViewer using the software. See TMT Installer Users Manual available on
http://support.videofied.com
4) Once you have everything mounted, arm the system and trip one MotionViewer at a time. Make sure you
stand in front of each MotionViewer for 10 seconds so the central station has some video to look at. (Page
25)
5) After you have sent signals to central station, call to verify.
The following pages will go through each one of these steps and, if you have any issues please reference the
troubleshooting guide on Pages 37-39. If you still cannot resolve the issue please feel free to call technical
support at 1-651-855-7800 EXT 45, 1-877-206-5800 EXT 45 or you can reach live support chat and additional
technical notes at support.videofied.com.
Sleeping mode and Wake-up on the CMA:
They keypad backlight will go out after 30 seconds of inactivity. When you press a button the keypad wakes up. The first touch on the
pad that wakes it up will not be a registered command and will only wake up the keypad.
Sleeping mode and wake-up on the XMA/XMB/WMB:
The keypad backlight will go out after 30 seconds of inactivity. The first touch on the keypad will wake up the keypad and will register as
a command to the control panel.
4|Page
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Introduction:
Description:
The XT series control panel is a Videofied wireless, battery operated hybrid alarm system.
It is designed for residential, small business and commercial security applications. The XT
provides integrated Video Verification over GPRS.
The XT has programmable inputs and outputs. XT also features mapping where an
external input can be used to generate a video clip from a MotionViewer.
Internal RF range and GPRS range can be enhanced using external antennas.
Supervised Wireless Technology:
The XT, along with all Videofied devices, uses the patented S2View® - Spread Spectrum,
Videofied, Interactive, AES Encrypted Wireless technology, providing optimum
signal integrity and security.
The bi-directional RF communication path between all devices and the system control
panel guarantees high signal reliability. Integrated antennas eliminate protruding wires or
rods, which are difficult to install, unsightly to consumers and potentially troublesome if
damaged.
The panel supervises every device (excluding the remote key fob) to validate current
open/close state, tamper condition, serial number, date of manufacture, firmware revision,
and battery status.
In order for an installation to be UL compliant you must follow the
specifications in the table below:
Type
Audio
Audio
Delays
Specifications
When a MotionViewer is
installed on the system you
may not have the siren sound
for less than 60 seconds
If no MotionViewer is installed
on the system you may not
have the siren sound for less
than 240 seconds
When a MotionViewer is
installed on the system the
Entry delay must be 45 seconds
Location In Manual
Page 41
Page 41
Page 9
5|Page
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
SETUP MANUAL
FOR
XT SERIES GPRS PANEL
*THIS SYSTEM REQUIRES A CMA/XMB/XMA/WMB or TMT INSTALLER SOFTWARE
FOR PROGRAMMING*
XT Initial Programming
Open the Control Panel
Using a #1 Phillips screwdriver, remove
the 2 screws holding the cover on.
The cover will fold off the panel like a
book with the curved side acting like the
binding. The same technique is used
when placing the cover back onto the
unit.
When removing the
XTO cover, pull straight
off, do not slide it.
6|Page
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
*The SIM card must NOT be inserted or removed while the panel is powered*
Install the SIM card
Slide SIM card into the slot.
Make sure it is aligned correctly.
Powering the Panel
**THE CONTROL PANEL MUST BE CONNECTED TO AN EXTERAL POWER SUPPLY
WHEN SMS FEATURE IS ACTIVE**
Option 1: PP1
4 x LSH20 SAFT Lithium D-Cell
Option 2
4 x E95VP Alkaline D-Cell + 12v 2amp DC Class 2
power supply (not supplied)
Used for Standalone or Xtender mode without
Programmable Inputs, Programmable Outputs, or
SMS
LSH20 Specifications:
Operating Temp: -76°F to +230°F
Storage Temp: Dry, Ventilated, 86°F Max
LSH20 Technical Specifications
Nominal Voltage
3.6 V
Open Circuit Voltage
3.67 V
Nominal Capacity
9.3 Ah
Used for Standalone or Xtender mode where
Programmable Inputs/Mapping, Programmable
Outputs, or SMS will be used
E95VP Specifications:
Operating Temp: 0°F to 130°F
E95VP Technical Specifications
Nominal Capacity
8900 mA hours
Nominal Voltage
1.5 V
Power Supply Requirements
Output Voltage (volts)
12
Output Current (mA)
2000
Class 2 (For UL
Certifications
Compliance)
7|Page
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
WARNINGS:
1. DO NOT USE ALKALINE BATTERIES IF
INSTALLING AN XTX/XTO GPRS BELOW
30° F, YOU MUST USE OPTION 1: PP1.
2. DO NOT INSTALL A TRANSFORMER
WHEN USING OPTION 1 (LITHIUM
BATTERIES).
Obtaining XMB/XMA Keypad Special Characters
Obtaining CMA Keypad Special Characters
8|Page
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
XT Programming
Reset the XT Panel:
Press and hold programming button () for 10sec until the
Indicator LED blinks twice

Press and instantly release the programming button ().
The indicator LED will blink once. The panel is now in ‘Learn
Mode’ for the CMA/XMB/XMA keypad.
*Note: If you are having issues
pairing the keypad to the panel,
please refer to the troubleshooting
section, page 37-39.

Insert all three batteries into the CMA601/XMB611/XMA611
and press both the ESC/NO and CLR keys at the same time
and release.
The indicator LED on the keypad will blink rapidly.
Programming Device/Keypad
RSI (c)2005
www.RsiAlarm.com
or
<======XX======>
CLR & ESC/NO
KEYPAD 1
RECORDED
YES/OK
Other languages are available by scrolling with arrows.
ITALIANO, NEDERLANDS, DEUTSCH, CASTELLANO,
SVENSKA, PORTUGUES, FRANCAIS
Press YES/OK for the selected one.
<- LANGUAGE : ->
ENGLISH

or
 for language selection
YES/OK to apply
9|Page
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
The Radio Range test must be run during device recording
to ensure proper pairing with the control panel. This tests
the number of successful ping between the device and the
control panel. The keypad will display a real time RF level
for the device that is being tested. This test will run until
stopped and should be run for at least 30 seconds to
receive accurate results.
RADIO RANGE
TEST ?
YES/OK
RF TEST
x/9
The RF level must be 9/9 for reliable transmission.
RADIO RANGE
TEST ?
YES/OK
ESC/NO
ENTER THE
INSTALLER CODE
Wait while the screen changes
From here until the end of initial programming
you will not be able to step back to a previous
parameter. All parameters can be changed after
initial programming has been completed.
4 TO 6 DIGITS
THEN YES/OK
INSTALLER CODE:
Use the Alphanumeric Keypad to enter the Installer Code
*This code is important to keep track of. There is no back
door to the system
INSTALLER CODE:
xxxx
CONFIRM CODE
RE-ENTER CODE
YES/OK
CONFIRM CODE
xxxx
You may name the installer code using the Alphanumeric
Keypad. If you leave the name blank it will default to
‘ACCESS 1’
CODE NAME :
YES/OK
ACCESS 1
ENTRY COMPLETE
Wait while the screen changes
ADJUSTING
TIME AND DATE
DATE (Year) :
09/ /
Use the

or

DATE (Year) :
10/ /
to set the Year
DATE (Month) :
10/01/
Use the

or

YES/OK
DATE (Month) :
10/11/
to set the Month
10 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
YES/OK
Use the

or

DATE (Day) :
09/06/01
to set the Day
YES/OK
DATE (Day) :
09/06/03
YES/OK
Use the

or

to set the Hour – The system uses a
24 hour clock.
TIME (HOUR) :
00:00
TIME (HOUR) :
10:00
Use the

or

to set the Minutes
DATE (Minutes) :
10:00
DATE (Minutes) :
10:53
YES/OK
03/06/09 10:53
ENTRY COMPLETE
YOU MUST ALWAYS CHOOSE ‘YES/OK’
CONNECTED TO
MONITOR.STATION?
Use the Alphanumeric Keypad to enter in a 4-8 digit account
number provided by the Central Station
ACCOUNT NUMBER?
YES/OK
ACCOUNT
NUMBER:99865123
Other periods are available:
48 hours, 24 hours, 12 hours,1 hour, No Test

Use arrows for the selection and press
YES/OK to
confirm.
*We suggest at least a 24 hour test
PERIODIC TEST:
24 HOURS

or
and

Use the arrow keys +
YES/OK to choose the Hour and
Minute the periodic test will happen.
YES/OK
 for period selection
YES/OK to apply
TEST HOUR:
00:00
TEST MINUTE:
00:00
11 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
CODE/STATE
MODIFICATION ?
CODE/STATE modification
YES/OK
These are the default transmitted events:
Device
Alarm
Alert
Alarm
Initialization
Not Transmitted
Panel Batteries
Alarm/End
AC Power
Alarm/End
Phoneline Fault
Not Transmitted
Tamper
Alarm/End
Device Batt.
Alarm/End
Radio Jamming
Not Transmitted
Supervision
Alarm/End
Periodic Test
Alarm
Wrong Codes
Not Transmitted
Duress Code
Alarm
Alarm Memory
Not Transmitted
Arm/Disarm
Not Transmitted
Fire
Alarm
Medical Assist
Alarm
ESC/NO
TRANS. STATE
MODIFICATION
YES/OK
List of all
events
YES/OK
TRANS. STATE
MODIFICATION
If you would like to change the state


to toggle
press
YES/OK and use the
or
between:
Alarm – Appearance
Alarm/End – Appearance and Restoral
Not Transmitted – Not Transmitted
ESC/NO
SERVER
ADDRESSES
YES/OK
If you would like the default press ESC/NO
Your IP1 address is given to you by your Central Station.
IP1 ADDRESS
YES/OK
YES/OK to enter into the parameter and use the
Keypad to complete the address. Press  YES/OK to
confirm your entry and the  arrow to move to the next
Press
parameter. *You will use either an IP address or a Domain
Name but not both
*When entering an IP address you must enter all 12 digits
including preceding 0s.
IP1 ADDRESS:
xxx.xxx.xxx.xxx
YES/OK

DOMAIN NAME 1
YES/OK
Your Domain Name is given to you by your Central Station.
YES/OK to enter into the parameter and use the
Keypad to complete the name. Press  YES/OK to
confirm your entry and the  arrow to move to the next
DOMAIN NAME 1:
xxxxx.xxx.xxx
Press
parameter. *You will use either a IP address or a Domain
Name but not both leave it blank if an IP has already been
entered.

PORT 1
YES/OK
PORT 1:
xxx
The Port is given to you by your Central Station. By default
the panel will use 888. If you need to modify the port press
YES/OK key to enter into the parameter and the
keypad to complete the port. Press  YES/OK to confirm
and the  arrow to move to the next parameter.
YES/OK
the
PORT 1
Continue through IP2 and TMT IP.
YES/OK
ESC/NO
Once you have entered all valid parameters press ESC/NO
to return to the main menu then ESC/NO again to move to
the next parameter.
SERVER
ADDRESSES
ESC/NO
12 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
GPRS
PARAMETERS?
YES/OK
APN CODE
YES/OK
Your APN code (Access Point Name) is given to you by your

Cellular Provider. Press
YES/OK to enter into the
parameter and use the Keypad to complete the code. Press
APN CODE:
xxxxx.xxxxxx.xxx
YES/OK to confirm your entry and the arrow to move
YES/OK
to the next parameter.
USERNAME
YES/OK
Your USERNAME is given to you by your Cellular Provider.
YES/OK to enter into the parameter and use the
Keypad to complete the name. Press  YES/OK to confirm
your entry and the  arrow to move to the next parameter.
Press
USERNAME:
xxxxxxxxxxx
YES/OK
PASSWORD
YES/OK
Your PASSWORD is given to you by your Cellular Provider.
YES/OK to enter into the parameter and use the
Keypad to complete the name. Press  YES/OK to confirm
your entry and the  arrow to move to the next parameter.
Press
PASSWORD:
xxxxxxxxxxxx
YES/OK
PASSWORD
ESC/NO
GPRS
PARAMETERS?
ESC/NO
During the GPRS Level test the Modem will boot and
attempt to gain access to the internet to post a Level out of
5 or an error Code that will help troubleshoot why it cannot
connect. To keep the keypad awake, use any keys on the
keypad except the YES/OK, ESC/NO, and CLR keys.
This test can take up to 5 minutes.
Once the level or error has posted press YES/OK to
continue in programming.
GPRS LEVEL?
YES/OK
TEST IN PROGRESS
YES/OK = END
*For explanation of GPRS errors see Page 20.
GPRS LEVEL
x/5
Videofied will require a 3/5 or better for reliable transmission
of Video alarms
GPRS LEVEL?
YES/OK
ESC/NO
Use the Alphanumeric Keypad to name the area and press
YES/OK.
Repeat for all four areas. If you want to keep
the default area names press the ESC/NO key.
AREA NAME 1:
By default Area 1 is a delay area and Area 2, 3, & 4 are
instant areas.
13 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
ARMING OPTION: Your choice will depend on how you are
arming the system.
From the host: Will make the XT a piggyback/xtender
system that arms and disarms off the latching of 9-12v on
the arming inputs. Wiring diagrams available on page 23.
ARMING OPTION:
Standalone

ARMING OPTION:
From the host
Standalone: Will make the XT a solo system controlled by
arming and disarming using Videofied peripheral devices.
Other values are available:
2 min, 1 min, 45 sec
Use the arrows for the selection and
YES/OK to confirm.
Other values are available:
2 min, 1 min, 45 sec, 30 sec, 15 sec
Use the arrows for the selection and
YES/OK to confirm.
EXIT DELAY:
45 Sec
ENTRY DELAY:
15 Sec
Go to Page 15 to continue
with standalone programming
Using the control panel as a Xtender system will only be able to arm and disarm by latching 9-12v to
one of the two inputs. For wiring diagrams see page 24.
Arming input 1 will control the arming and disarming of devices in areas 1 and 2. Where devices in
area 1 are subject to the Entry Delay.
Arming input 2 will control the arming and disarming of devices in areas 3 and 4. Where devices in
area 3 are subject to the Entry Delay.
Mode Slow : Used for following the arming and disarming of
the host system. This will arm each device one at a time
conserving battery life.
Mode Fast : Used to instant arm all devices while sacrificing
battery life.
ARMING OPTION :
From The Host
MODE:
Slow
Press ESC/NO if first Radio Range Test was successful.
YES/OK

MODE:
Fast
YES/OK
YES/OK
Enter the value for your Entry Delay up to 255 seconds and

ENTRY DELAY
press
YES/OK. This parameter should match the entry
delay on the host system.
VALUE:(0-255)
(000):
YES/OK
14 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
By entering a value using the keypad, up to 600 seconds,
the transmission of any event will be delayed that many
seconds.
TRANSMISSION
DELAY
Enter the value you would like for the Transmission Delay
Value: (0-600)
(000):
and press
YES/OK

YES
YES/OK
/OK
YES/OK
Arming Confirmation is the number of seconds of latched
voltage (where voltage must stayed latched after) the panel
will require before arming. This will be considered your exit
delay and should match the exit delay of the host system.
Enter the value you would like for the Arming Confirmation
and press
YES/OK
ARMING
CONFIRMATION
Value: (0-240)
(0):
YES/OK
Standalone
programming
continued
RECORDING
DEVICES
Each device has a unique programming button. Please
reference the Installation Sheet for the device you would like
to program for mounting and learning process. Programming
button locations are available on page 16 of this manual.
PRESS PROGRAM
BUTTON OF DEVICE
*Note: If you are having issues pairing a device to the panel,
please refer to the troubleshooting section.
Press YES/OK on Radio Range Test? You must allow the
Radio Range test to run for at least 30 seconds (9/9) before
stopping the test by pressing YES/OK.
YES/OK
(Device Type) #
Recorded
RADIO RANGE
TEST?
RF TEST
x/9
Press ESC/NO if first Radio Range Test was successful.
Use the arrow keys to select the proper area. Devices that
need an entry/exit delay should be set to AREA 1. Devices
that must be instant trigger should be AREA 2, 3, or 4. Press
YES/OK.
RADIO RANGE
TEST?
AREA ALLOCATION:
NAME LOCATION:

FUNCTIONAL
DEVICE TEST?
ENTERING A NEW
DEVICE?
YES/OK
or ESC/NO
CLOSE THE PANEL
Before completing programming make sure that all tampers
are depressed by verifying that each devices indicator LED is
off.
OPERATION
COMPLETED?
YES/OK
15 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Device Installation
DCV#51 – Outdoor MotionViewer / BR#51 Outdoor Badge Reader
Place batteries in Device. Wait for LED to turn on. Press and release the programming
button.
DCV#01 – Indoor MotionViewer / ITR#01 – Indoor Blind PIR
Place batteries in device. Wait for LED to turn on behind PIR lens. Press and release the
programming button.
DCV601
ITR601
CT#01 – Door/Window Contact
Place battery into the door/window contact. Wait for LED to turn on. Press and release the
programming button.
RC#01 – Remote Control Fob
Press and hold the ON and OFF keys at the same time for 5 counts of Mississippi and
release.
SE#51/#01 – Indoor and Outdoor Sirens
Place all batteries into the siren. Wait for the LED to turn on right above the programming
button. Press and release the programming button.
16 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
How to Disable/Enable Monitoring
Disabling monitoring can be a useful tool in many situations. Before mounting devices and moving the panel to find a
good GPRS level, disabling monitoring will ensure that you will have access to programming and that unnecessary
signals are not sent to the monitoring station. When performing maintenance on the system, disable monitoring until
the issue has been resolved. This will ensure that you will have access to programming throughout your
troubleshooting.
Press the
arrow to move to ACCESS LVL.
10/12/27 10:53
DISARMED LVL:1
ACCESS LEVEL
1
Use your arrow keys to change the level to 4
YES/OK
ACCESS LVL: 4
YES/OK
Enter the installer code for the system.
BADGE OR CODE
****
*Firmware XLP.03.50.xx will now ask for a Level 3 user code
Press the

YES/OK
CONFIGURATION
to move to CONFIGURATION
Enter the installer code for the system
GENERAL
PARAMETERS
 to move to CONFIGURATION MONITOR.
Use the
STATION
CONFIGURATION
MONITOR. STATION
YES/OK
Press YES/OK on MONITORING PARAMETERS
MONITORING
PARAMETERS
Press YES/OK on MONITORING ENABLED and use the
to change the value to DISABLED and press YES/OK to
lock it in. Press and hold ESC/NO for 5 seconds to return to
the main menu.
MONITORING
ENABLED
YES/OK
MONITORING:
DISABLED
YES/OK
17 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Entering a Badge or Access Code for Arming/Disarming
After Initial programming has been completed, you are not able to arm and disarm the system until
you enter a user code or badge (the installer code cannot arm and disarm the system). Codes can
be 4-6 digits and the 4th digit must be 2 values higher or lower than any other code on the system:
Example: User code 1234, next code cannot be 1235, 1236, 1233, or 1232 – These are reserved for
Silent Duress and Audible Duress. The XT system can accept up to 19 Badges or Access codes in
any combination.
10/12/27 10:53
DISARMED LVL:1
You must first change the access level to 4. Right Arrow to
Access Level and press YES/OK. Use the arrow keys to
move to Level 4 and press YES/OK. When prompted with
Badge Or Code enter the installer code followed by YES/OK.
Press the
ACCESS LEVEL:
4
YES/OK
BADGE OR CODE
****
arrow to move to BADGES ACCESS CODES.
BADGES ACCESS
CODES
YES/OK
ENTER A
BADGE/CODE
YES/OK
Enter a 4-6 digit user code or present a badge to the reader
for 2 seconds.
BADGE OR CODE:
****
YES/OK
Confirm the code by re-entering.
CONFIRM THE
CODE:
Badge
Presented
YES/OK
Use the keypad to name the badge or code or leave it blank
for the default name: ACCESS #.
CODE NAME:
NAME OF BADGE:
YES/OK
YES/OK
ENTRY COMPLETE
If you are entering any additional codes press YES/OK. If you
have completed entering Badges and Codes press and hold
ESC/NO for 5 seconds to return to the main manu.
Reserved codes
000000
ENTER A
BADGE/CODE
Reserved codes
Reserved codes
From 9998 to 9999
All codes +1
From 99998 to 99999
All codes +2
From 999898 to 999999
All codes -1
From 314157 to 314159
All codes – 2
A total of 186 codes are forbidden
18 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Access level
Definition & rights
LVL1
Stand by level
LVL2
Restricted USER level where it is only possible to arm/disarm the system.
LVL3
USER level where it is possible to arm/disarm the system, check the event
log, test the devices.
Modifications of the setting are not possible at this level.
User LVL3 can create LVL3 or LVL2 access codes.
INSTALLER level where it is possible to modify the setup of the panel. The approval of a
LVL3 or LVL2 is required to modify the level for LVL4.
LVL4
Installer LVL4 can create the first LVL3 access code only.
Configuration of Special Arming Modes:
To configure or modify a special arming mode, with the direction arrow go to the menu:
CONFIGURATION (LEVEL 4) + [YES/OK]  ALARM MODES PROGRAMMABLE + [YES/OK]
 FULLY ARMED, SP1 and SP2 (use direction arrows to select the arming mode you want to
modify + [YES/OK]).
For each arming mode, it is possible to specify how each of the 4 areas will be armed and how
the system will behave during an alarm.
Areas:
States:
1 2 3 4 press the corresponding number to change that areas arming option
A A A A state for the respective area.
Press the [YES/OK] key after this configuration step. The system will then display what siren
mode will be in effect for this special profile. Select the siren mode using the direction arrows
then press [YES/OK].
A
D
P
Armed
Disarmed
Perimeter Devices Only
E
External Devices Only
(devices must be programmed)
(devices must be programmed)
Siren
Delay beeps
Silent
Without Siren
Immediate triggering of all sirens
Entry/Exit delay beeps, then triggering of the sirens
No Sirens, No Beeps
Beeps on the keypad only
19 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
How to test GPRS for deployment of panel
Before the system is mounted you will need to check the GPRS level to make sure it is adequate. Videofied Control
Panels require a 3/5 or better for reliable transmission.
10/12/27 10:53
DISARMED LVL:1
First change your access level to 3 or higher
Press the
arrow to move to MAINTENANCE.
Press the
arrow to move to GPRS LEVEL.

ACCESS LEVEL
3

MAINTENANCE

Press YES/OK on GPRS LEVEL to start the test.
GPRS LEVEL
YES/OK
This test can take up to 5 minutes to complete. Pressing the
YES/OK, ESC/NO, or CLR buttons will prematurely end the
test. This test will automatically issue the results to the
display of the keypad when it has completed with either a
level out of 5 (0/5-5/5) or an error code (listed below). Use
the arrow keys to keep the keypad awake during the test.
TEST IN PROG.
YES/OK = END
GPRS LEVEL
X/5
Press and hold ESC/NO for 5 seconds to return to the main
menu.
YES/OK
GPRS LEVEL
GPRS Errors when running GPRS LEVEL and in the Panel EVENT LOG
GPRS Level
EVENT LOG
Error
010
11
SIM card not detected/not inserted
043
44
Provisioning problem
132
133
SIM card not activated
255
256
Cannot connect to cell tower
003
3
SIM Card not detected/No Cellular
Service
030
31
No Cellular Service
101
*
Authentication Error
102
149
*
*
No Cellular Service
*
Low Cellular Signal
47
Rejection by Host
013
*
Incorrect APN Code
*
13
SIM Card not detected
Fix
Power down control panel and
check SIM card orientation and
contacts
Contact the cellular provider to
check provisioning and activation
Check with the cellular provider on
SIM activation
Check coverage maps, bring panel
outdoors to test,
Check coverage maps, power down
control panel and check SIM card
orientation and contacts
Check coverage maps or with
cellular provider for outages
Check that the APN entered in the
system is correct
Check coverage maps, move the
panel outdoors to test, check with
cellular provider for outages
Attempt a Yagi antenna installation
to improve strength
IP, Domain Name, Port are
incorrect or Receiver is rejecting the
signal
Check with provider for proper APN
information
Power down control panel and
check SIM orientation and contacts
20 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
How to enable the External RF Antenna
The XTO 600/610 control panels have built in High Gain RF and GPRS antennas. The GPRS external
comes pre-activated and hooked up, while the RF antenna is hooked up but needs to be activated in
Configuration after you have completed initial programming. The following steps will walk you through how
to enable the High Gain RF antenna after initial programming.
Press the
arrow to move to ACCESS LEVEL #.
10/12/27 10:53
DISARMED LVL:1
ACCESS LEVEL
1
Press YES/OK and use the
 to move the level to 4
YES/OK
ACCESS LVL:
4
YES/OK
BADGE OR CODE:
****
Enter the Installer code.
Press the
YES/OK
CONFIGURATION
arrow to move to CONFIGURATION
GENERAL
PARAMETERS
YES/OK
Left or Right arrows until you see RADIO OPTIONS and
press YES/OK. Use the arrow keys to change it to External
and press YES/OK.
SITE
IDENTIFICATION
RADIO OPTIONS:
EXTERNAL
YES/OK
21 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
How to test RF for deployment of devices
Running the RF test during the mounting of devices is key to a successful Videofied installation. This test
will ensure that all devices have adequate communication with the control panel. All Videofied devices are
bi-directional which allows the system to ping the device and expect a response. The number of successful
responses out of 9 will be displayed on the keypad for the device you are running the test for. This is also a
relative range that will change in real time as you walk further away from the control panel and back closer.
First change your access level to 3 or higher
Press the
Press the
10/12/27 10:53
DISARMED LVL:1
arrow to move to MAINTENANCE.
arrow to move to DEVICE LOCATING
Press YES/OK on DEVICE LOCATING to get to the list of
devices. Use the arrow keys to find the device you would like
to run the test for.
MAINTENANCE
DEVICE LOCATING

ACCESS LEVEL
3

YES/OK
(DEVICE NAME)
This test will run as long as you need it to. Pressing the
YES/OK, ESC/NO, or CLR buttons will end the test. This
test will show the results on the display of the keypad
relative to the number of successful pings to the panel. It is
required to run the test for at least 30 seconds at the
mounting location for accurate results and to have a 9/9 for
reliable transmission of alarms and video. Press YES/OK
when you are finished with the test.
Press and hold ESC/NO for 5 seconds to return to the main
menu.
RF TEST
0/9
YES/OK
YES/OK
(DEVICE NAME)
Once all devices are checking in at 9/9, you are ready to test
the full system to your central station. After arming and
tripping each device call the central station and verify alarm
and video of each device with dispatch.
Now you are ready to show the customer how to use the
system.
NOTE: To insure proper operation of the system you must get 9/9 with each device
before mounting.
22 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
GPRS Antenna Connection
! WARNING !
Use caution before removing antenna connection. A damaged antenna connector is NOT
covered under warranty.
Using needle nose pliers, be
sure to only grab the
connector and pull directly up
XT series Power Chart
23 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Arming Input Wiring Diagram
When in the ‘Arm From Host’ mode the Videofied system will only arm and disarm when
9-12v is supplied and sustained. When both arming inputs are supplied voltage at the same
time the Videofied Keypad display will show ‘SYSTEM ARMED. When only one arming
input is supplied voltage the Videofied Keypad display will show ‘PART LVL #’
Arming Input 1 will arm/disarm Areas 1 & 2
Arming Input 2 will arm/disarm Areas 3 & 4
24 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
How to test to the dispatch center
Testing to the dispatch is done twice during installation. Once while you are programming the
system and then again once the installation has been completely finished. Although both will use the
same steps the initial test will be just confirmation using one device to verify the programming.
10/12/27 10:53
DISARMED LVL:1
Enter a User code and press YES/OK or present a badge to
the reader.
10/12/27 10:53
****
YES/OK
The system will sound the exit delay through the keypad and
badge reader.
Once the delay has expired and the keypad says SYSTEM
ARMED, put motion in front of a MotionViewer. If the
MotionViewer is in area 1 you will need to wait for the entry
delay to expire before disarming the system. Once the
system has gone into alarm enter a User Code followed by
YES/OK or present a badge to the reader to disarm.
ARMING THE
SYSTEM
SYSTEM ARMED
SYSTEM ARMED
****
The display will tell you that there has been an intrusion since
the last time the system was armed. Press YES/OK to
continue.
After pressing YES/OK the keypad will tell you which device
has been triggered. Press YES/OK to continue.
INTRUSION
DETECTED
YES/OK
YES/OK
(DEVICE NAME)
(AREA)
YES/OK
The system will go back to the main menu automatically but
will not allow you to move around in programming until the
system has disconnected from the central station.
10/12/27 10:53
DISARMED LVL:1
Note: Send 1 MotionViewer in at a time and verify with Central Station that they are
getting Alarm and Video before tripping another MotionViewer. This will save time with
the Central Station.
25 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
How to mount the XT#00i/#10 and XTX#00i/#10
How to Mount the Control Panel?
Fix the back casing on the wall
with 3 screws ()
.



How to Mount the XTO#00/#10
Included Mounting Hardware:
Case and Mounting
Screws, locking
washers, bolts and
nuts.
Mounting Brackets
1. Install the Weather Resistant Wire Port.
26 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
2. Place the cover on the base.
1. When closing the cover be sure
to line up the two BOTTOM
stickers face to face.
2. Be Careful not to slide the cover
on. Instead come straight down
in order to have the cover tamper
properly seat.
3. Screw the cover to the base using the provided 8 screws.
NOTE: To ensure proper
functioning and to keep the case
water proof you must mount the
panel with the wire channel facing
down.
4. Place the L shaped mounting bracket onto the base using the provided bolts.
5. Place the two U shaped brackets around the pole and attach the locking bracket. Use the locking
washers and nuts to attach the U bracket to the L mount.
27 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
General Programmable Input Configuration
28 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
29 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
30 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
31 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
32 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
33 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
34 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
35 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
36 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Troubleshooting
Monitoring Station is not getting ANY video but is getting signals:
Good communication between the MotionViewers and the Control Panel is key to getting successful
video to the monitoring station. During mounting of any device on your Videofied system you must
run the Radio Range/Device Locating test to ensure that the mounting location is with-in range of the
Control Panel.
 Concrete, Metal and earth are some of the largest RF inhibitors and should be taken into
account when choosing mounting locations.
 When running the Radio Range/Device Locating test you should have the site as close to the
same as it would be when the site is closed/no one is there, i.e. close garage doors/service
doors, etc. Device locating steps can be found on Page 17.
Devices are not
sending Video
clips
YES/OK –
There are
faulty devices
Check
Maintenance/
Display Faulty
Devices
NO – There are no
faulty devices
MotionViewers
come up with
‘Radio Problem’.
This means that
the MotionViewers
are currently not
talking with the
Control Panel.
Run
Maintenance/
Device
Locating
Device Locating will test the RF
signal strength between the device
and the Control Panel. For reliable
transmission this result must be a 9/
9. This is the number of successful
pings between the device and the
Control Panel so a loss of just 1
packet could cause failure to
transmit video.
Bring the devices
back to the Control
Panel and hit the
programming
button to force
them to sync back
with the panel.
Important Note: Videofied will only automatically download the first MotionViewer video that is taken and
only if this is the primary event or reason for the panel connecting with the monitoring station. If the account
is on test you will only ever get the first video downloaded. If you are only getting the events at the station
and all tests above pass more than likely you are sending a preceding event (like an arming signal or door
contact) which will cause the video to not auto download because the video is not the primary event.
37 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Monitoring Station is not getting any signals:
Communication between the Control Panel and the Monitoring Station is over the GPRS side of the
GSM cellular network.
 You will want to check your GPRS level to see if there is an error/level is too low. You must
have a 3/5 or better for reliable transmission to the Monitoring Station. How to run the GPRS
level test and GPRS error codes can be found on page 16.
 If you receive a successful GPRS level test you will want to check the panel event log for more
GPRS errors that could be occurring during the attempted transmission but after cellular
authentication.
No Signals are
received at the
Monitoring Station
GPRS Error
Run GPRS Level
test in Maintenance
GPRS Level
3/5-5/5
GPRS LEVEL
RECEIVED
GPRS Level
0/5-2/5
GPRS errors can
be found on Page
16 of the manual.
Check the panel event
log. This will give
additional GPRS errors
that may be occurring
during the attempt of
transmission. See Page
16 for Event Log GPRS
meanings.
Your signal strength must be 3/5
or better for reliable transmission
to the monitoring station. There
are external antennas available
and other cellular repeater options
if needed to boost cellular
reception
Panel is staying CONNECTED WITH MONITOR STATION
While the Control Panel is attempting or is connected with the Monitoring Station you will see this
message when you attempt to move around on the keypad. If the system is not successful in
connecting with the station it will retry the connection multiple times, locking you out of programming
until it is done trying. This normally can take anywhere between 15-20 minutes.
 If you want to force the panel to disconnect you must
o 1. Remove the batteries from the control panel
o 2. Secure the cover tamper of the panel
o 3. Re-insert the batteries into the control panel and sync the keypad back by pressing
the CLR and ESC/NO buttons at the same time.
o 4. Access the Configuration menu by changing you access level to 4 and go to
Configuration Monitor Station.
o 5. In Monitoring Parameters – Disable monitoring until the connection issue is resolved.
38 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Unable to record device or getting ‘Pairing Failure’ error
This usually occurs when the device still has a pairing key from a previous system or setup. To
perform a pairing key override:
o
o
o
o
o
1. Remove all batteries from the device.
2. Make sure your system is ready to record devices:
o A. If learning in the keypad, press the panel’s programming button. DO NOT
HOLD THE PANEL’S PROGRAMMING BUTTON
o B. If learning in additional devices, make sure the keypad reads ‘Press
Programming Button Of Device’
3. Insert a single battery into the device.
4. Wait 1 second for device to power up.
5. Press programming button of device (for keypads press ‘CLR’ & ‘ESC/NO’ keys at the
same time)
For the 4-button remote keyfobs the process is slightly different:
o 1. Press and hold the ‘ON’ and ‘OFF’ keys at the same time for 12 seconds
o 2. Wait 1 second
o 3. Press and hold the ‘ON’ and ‘OFF’ keys at the same time for 5 seconds, you should
hear 4 beeps from the keyfob.
Outdoor MotionViewer Trips All the Time:
It is important to follow these basic installation tips when mounting and aiming an outdoor
MotionViewer
o 1. Protect your assets, not the whole area.
 Secure specific assets or clusters of assets rather than cover a large
area where the range of the MotionViewer might extend beyond the
assets and detect irrelevant objects.
o 2. Terminate the view of the MotionViewer.
 Make sure to tilt the MotionViewer down 5-7° so that its top line of
sight terminates into the ground. Taking into account all three
elements; PIR, digital video camera, and infrared illuminators – you
will want to terminate the view of the MotionViewer at 40 ft. from the
device.
39 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
XT -SERIES ‘AFTER INITIAL PROGRAMMING’ FLOW CHART
End of Initial
Programming
Event Log
Select Last Events
Event List
Badges / Access
Codes
Programmable
Features
DISARMED LVL
Access Level
Configuration
System Armed
Access Level
Level #
Configuration
Menu (Page 41)
Enter A Badge/
Code
Maintenance
Modifying
Date/Time
Badges/Codes
Configuration
Panic Buttons
Badge/Codes
List
Modif. Name
Badge/Code
Access Level #
Schedule
Authorize
Select/Modify
Schedules
Enter A New
Schedule
Areas
Disarmed
Alarm Modes
Enabled
Alarm Modes
Enabled
Police
Siren/Disable/Silent
Medical
Siren/Disable/Silent
Fire
Siren/Disable/Silent
Maintenance
Replace Batteries
Maintenance
Devices/Panel
Functional Device
Test
Device Locating
Config Bypass
List Of Devices
_/ BYPASS
SMS
SMS Decoding
Enabled/Disabled
SMS Reply
Enabled/Disabled
Alarm Modes
Enabled
Modifying
Date/Time
Audio test
Equipment
Audio Device List
Display Faulty
Devices
Devices List
Alarm Modes
Enabled
GPRS Level
Deleting Badges/
Codes
Badge/Code List
Parameter is only available in
Access Level 4
40 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Configuration
General
Parameters
Alarm Modes
Programmable
Site Identification
Phone Number
Responding Party
List
Fully Armed
Not Supported in
North American
Market
Areas: 1234
State: AAAA
Name Or Address
Areas: 1234
State: AAAA
Areas and
Devices
Configuration
Monitor Station
Monitoring
Parameters
Devices
Monitoring?
Enabled
Add A New
Device
Account Number
Devices
Configuration
Server Addresses
Programmable
Outputs
Devices List
Programmable
Output 1
Status:
Enable/Disable
IP 1 Address
Alarm SP1
Delete Device
Port 1
Length Active
Event Type
Output Name
Programmable
Output 2
Domain Name 1
Changing Name
Device
Areas: 1234
State: AAAA
Changing Area
Device
Alarm
Siren/Silent/W. Sir.
IP 2 Address
24 Hour Device
Enable/Disable
Silent Arming
Disable/Enable
Domain Name 2
24 Hour Siren
Mode
Designation
Mode
Port 2
TMT IP Address
Areas
Programmable
Inputs
Alarm SP2
Domain Name
TMT
Areas List
Programmable
Input 1
Transmission
Enable/Disable/
Only If Armed
Areas: 1234
State: AAAA
Alarm Mode
Alarm/Alarm-End
Alarm
Siren/Silent/W. Sir.
Input Type
Open/Closed
Silent Arming
Disable/Enable
Event Type
Designation
Mode
Input Name
Port TMT
Area Content #
Area #
Area Devices
List #
Changing Name
Area #
Periodic
Test
Periodic
Test
Test Hour
Siren Duration
Intrusion
System Armed
Enabled/Disabled
Siren Mode
Siren/Silent/W.o.
Siren
Siren Duration
Tamper
Mapping
Inactive/Device
Name
Entry Delay
Periodic Call
Disable, 30, 90
Exit Delay
Test Hour
Programmable
Input 2
Delay Beeps
Enabled
Programmable
Input 3
Periodic Call
Monitoring Station
Alarm Codes
Auto Arming
Delay
Trans State
Modification
Scheduling
Event List
GPRS Parameters
APN Code
Scheduling
Off/Enabled
Intercom
Username
Password
Packet Size
Calendar
Management
Touchpad &
keypad
Erase Calendar?
Low Batt Msg
Disable/Enable
Data Timeout
SMTP GPRS
Radio Options
Built In Antenna/
Ext
Erase Calendar?
Calendar Erased
Port GPRS
Max Seg. Size
Warning Bip
Enabled
Ring Tone
Off/Auto
41 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
Addendum
1. LSH20 Control Panel
Batteries:
2. LS14500 Peripheral
Batteries: Excludes SE601
and SE651
3. Lithium Battery Storage:
42 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
4. Finding Manufacture Week and Year:
The Manufacture week and year can be found in the serial number of the device/control panel. The
second sets of 4 numbers in the serial number are WWYY.
####0411######## - This device was manufactured in the 4th week of 2011.
5. Additional System Codes
Codes
Action
999999
Maintenance request - GPRS transmission
999998
Displays IP address of the SIM card while communicating.
999991
999997
Sends a test alarm to IP1 Address (Primary alarm receiver)
This is a quick way to check for connectivity to the monitoring center. If there is a
transmission problem the panel will terminate communication faster than in an actual alarm.
The system will automatically attempt connection to IP2 Address (Backup alarm receiver) in
the event that IP1 is unavailable.
Displays external power supply status
6. Replacing Device and Control Panel batteries
When replacing batteries in the Videofied control panel or devices the battery replacement mode
must be used. This will ensure that the low battery algorithm on the panel/device is properly reset
and also helps keep the devices synced with the control panel.
Devices:
Access Level 4 -> Maintenance -> Replace Batteries -> Devices
The system will give you 1 minute to open any device on the system to replace the batteries.
When a device is opened you will have 5 minutes to replace the batteries before the system will
time out and all tampers will be active again on the system. We suggest that you start the device
battery replacement for each individual device to ensure the 5 minutes does not expire and tamper
signals are not sent to the monitoring station.
Control Panel:
Access Level 4 -> Maintenance -> Replace Batteries -> Panel
The system will give you 1 minute to open the panel. When the panel is opened it will give
you 5 minutes to replace the batteries before the control panel tampers will be active again.
43 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
2011/11/10 Ed 1.5
Setup and Programming manual for XT series GPRS
7. Checking control panel firmware version
1. All control panel labels on the box and inside of the cover will have the firmware
version listed.
2. After completing initial programming hit the 0 key 6 times followed by YES/OK
(000000 + YES) and the firmware version will be listed.
3. Connect the panel to TMT2 using the USB or Cellular connection. The firmware
version of the control panel is listed on the main screen.
44 | P a g e
1375 Willow Lake Blvd., #103
Vadnais Heights, MN 55110
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising