IntelliTouch Expansion Center Installation Guide

IntelliTouch Expansion Center Installation Guide
pool/spa control system
IntelliTouch® Expansion Center Kit
Installation Guide
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
© 2005 Pentair Water Pool and Spa, Inc. All rights reserved
This document is subject to change without notice
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400
Trademarks and disclaimers
IntelliTouch, EasyTouch, IntelliChlor, IntelliFlo, QuickTouch, MobileTouch, SAm, SAL, and FIBERworks, and the
Pentair Water Pool and Spa logo are trademarks of Pentair Water Pool and Spa, Inc. Other trademarks and trade
names may be used in this document to refer to either the entities claiming the marks and names or their products.
Pentair Water Pool and Spa, Inc. disclaims proprietary interest in marks and names of others.
P/N 520471 - Rev A - 09/27/05
i
Contents
IMPORTANT SAFETY PRECAUTIONS ............................................................... ii
IntelliTouch Expansion Center Kit Contents ............................................................. 1
About the Installation Guide ..................................................................................... 1
Related Manuals ...................................................................................................... 1
Technical Support .................................................................................................... 1
Installation Steps Summary ..................................................................................... 2
Expansion Center Enclosure Location .................................................................... 2
Expansion Center Setup Options ............................................................................ 2
Installing Conduit and Wire ...................................................................................... 3
Installing the Outdoor Control Panel ........................................................................ 4
Connecting the Expansion Center Pre-Installed Relays .......................................... 5
Installing Auxiliary Relays (Model i5x and i10x) ........................................................ 6
Connecting the Expansion Center to the Load/Power Center ................................. 7
Connecting the Expansion Center Transformer ...................................................... 9
System Wiring Diagram .......................................................................................... 10
Glossary .................................................................................................................. 11
IntelliTouch Expansion Center Kit Installation Guide
ii
IMPORTANT SAFETY PRECAUTIONS
Important Notice:
Attention Installer: This manual contains important information about the installation, operation
and safe use of this product. This information should be given to the owner and/or operator of this
equipment.
WARNING - Before installing this product, read and follow all warning notices and instructions
which are included. Failure to follow safety warnings and instructions can result in severe injury,
death, or property damage. Call (800) 831-7133 for additional free copies of these instructions.
WARNING - Water temperature in excess of 100 degrees Fahrenheit may be hazardous to your
health. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the
internal temperature of the body reaches a level several degrees above normal body temperature of
98.6° F (37° C). The symptoms of hyperthermia include drowsiness, lethargy, dizziness, fainting,
and an increase in the internal temperature of the body.
The effects of hyperthermia include: 1) Unawareness of impending danger. 2) Failure to perceive
heat. 3) Failure to recognize the need to leave the spa. 4) Physical inability to exit the spa. 5) Fetal
damage in pregnant women. 6) Unconsciousness resulting in danger of drowning.
WARNING - To reduce the risk of injury, do not permit children to use this product unless they
are closely supervised at all times.
WARNING - The use of alcohol, drugs, or medication can greatly increase the risk of fatal
hyperthermia in hot tubs and spas.
WARNING - Control System is intended to control heaters with built-in high limit circuits ONLY.
Failure to do so may cause property damage or personal injury.
WARNING - Do not use this product to control an automatic pool cover. Swimmers may become
entrapped underneath the cover.
WARNING - For units intended for use in other than single-family dwellings, a clearly labeled
emergency switch shall be provided as part of the installation. The switch shall be readily accessible
to the occupants and shall be installed at least 10 feet (3.05 m) away, adjacent to, and within sight of,
the unit.
CAUTION - Except for listed spa-side remote controls, install a minimum of five (5) feet from
the inside wall of the pool and spa.
IntelliTouch Expansion Center Kit Installation Guide
iii
IMPORTANT SAFETY PRECAUTIONS (Continued)
General Installation Information
1. All work must be performed by a licensed electrician, and must conform to all national, state,
and local codes.
2. Install to provide drainage of compartment for electrical components.
3. If this system is used to control underwater lighting fixtures, a ground-fault interrupter
(GFCI) must be provided for these fixtures. Conductors on the load side of the ground-fault
circuit-interrupter shall not occupy conduit, junction boxes or enclosures containing other
conductors unless such conductors are also protected by a ground-fault circuit-interrupter.
Refer to local codes for details.
4. A terminal bar stamped
is located inside the supply terminal box. To reduce the risk
of electric shock, this terminal must be connected to the grounding means provided in the
electric supply service panel with a continuous copper wire equivalent in size to the circuit
conductors supplying this equipment (no smaller than 12 AWG or 3.3 mm). The bonding
lug(s) provided on this unit are intended to connect a minimum of one No. 8 AWG for US
installation and two No. 6 AWG for Canadian installations solid copper conductor between
this unit and any metal equipment, metal enclosures or electrical equipment, metal water
pipe, or conduit within 5 feet (1.5 m) of the unit.
5. The electrical supply for this product must include a suitably rated switch or circuit breaker
to open all ungrounded supply conductors to comply with Section 422-20 of the National
Electrical Code, ANSI/NFPA 70.1987. The disconnecting means must be readily
accessible to the tub occupant but installed at least 10 ft. (3.05 m) from the inside wall of
the pool.
6. Supply conductor must be sized to support all loads. Maximum supply conductor current
must be 125 Amps at 125 VAC or 63 Amps at 240 VAC.
IntelliTouch Expansion Center Kit Installation Guide
iv
IntelliTouch Expansion Center Kit Installation Guide
1
IntelliTouch Expansion Center Kit Contents
The following items are included in the Expansion Center kit. If any items are missing please contact
Technical Support.
•
IntelliTouch Expansion Center
•
Outdoor Control Panel. Includes motherboard and Personality board
•
Power Relays - Models i5x and i10x (5 relays)
•
Wiring Diagram Label - To affix to the inside front door (for models i5x and i10x)
•
Label Sheet - A set of adhesive labels for custom identification (for outdoor control panel
buttons). Use a pair of fine-tip tweezers to remove the labels from the sheet
•
IntelliTouch Expansion Center Kit Installation Guide (this manual)
About this Installation Guide
Use the information in this manual to install the IntelliTouch Expansion Center kit contents.
Related Manuals
•
For information about configuring an Expansion Center with the IntelliTouch system, refer to
the IntelliTouch System User’s Guide (P/N 520102)
•
For Load Center and Power Center installation instructions, refer to the Load Center and
Power Center Installation Guide (P/N 520100)
•
For additional IntelliTouch installation information, refer to the IntelliTouch Personality Kit
Installation Guide (P/N 520101) and the IntelliTouch System User’s Guide (P/N 520101)
Technical Support
Contact Technical Support at:
Sanford, North Carolina (8 A.M. to 5 P.M.)
Phone: (800) 831-7133
Fax: (919) 566-8920
Moorpark, California (8 A.M. to 5 P.M.)
Phone: (800) 831-7133 (Ext. 6502)
Fax: (805) 530-0194
Web sites
visit www.pentairpool.com and www.staritepool.com
IntelliTouch Expansion Center Kit Installation Guide
2
Installation Steps Summary
Note: Use the following instructions to install and connect additional expansion center enclosures to
existing Load Center or Power Center. For Load Center or Power Center installation instructions,
refer to the Load Center or Power Center Installation Guide (P/N 520100).
The recommended installation steps for the Expansion Kit are as follows:
1
Install the Outdoor Control Panel (page 4): Remove the high voltage panel from the
Expansion Center enclosure and install the Outdoor Control Panel.
2
Connect Pre-installed Relays (page 5): Connect the relay plugs to the Personality board.
The four relays are pre-installed in the Power/Load Center.
3
Installing Auxiliary Relays (page 6): Install and connect the relay(s). For models i5x and i10x.
4
Connecting the Expansion Center to the Load/Power Center (page 7): Connect the 4-wire
cable from the Load Center or Power Center to the COM port on the Personality board in the
Expansion Center enclosure.
5
Connecting the Expansion Center transformer (page 9): Connect the transformer harness
to the Personality board.
6
Affixing the System Wiring Diagram Label (page 9): Affix the wiring diagram on the inside of
the front door of the Expansion enclosure (for models i5S, i9+3S, i10+3D only).
Expansion Center Enclosure Location
All pool equipment including the Expansion Center enclosure, with the exception of the Spa-Side
remote, must be located at least 10 ft. from the water’s edge.
Expansion Center Setup Options
An Expansion Center enclosure can be a Load Center or Power Center enclosure. Install the
Expansion Center enclosure’s near to the main Load Center or Power Center. The Expansion Center
can support all of the same high voltage connections as the main load to the Load Center or Power
Center. For more information, refer to the Load Center and Power Center Installation Guide (P/N
520100). The Expansion Center enclosure includes COM port connections, and two actuators as
does the Load Center or Power Center. The Expansion Center enclosure can be expanded to
include up to five actuators (with valve module P/N 520285).
Main Load Center
(i9+3, i9+3S, i10+3D)
Expansion Center
(i5x or i10x)
IntelliTouch Expansion Center Kit Installation Guide
Additional
Expansion
Center
Additional
Expansion Center
(3 maximum)
3
Installing Conduit and Wire
•
Run the appropriate size conduit from the sub-panel to the Expansion Center (see diagram
below for knockout locations). Run the appropriate conduit and wire from the main Load
Center or Power Center to the Expansion Center.
•
Run a 4-wire communication cable from the Load Center or Power Center to the Expansion
Center.
•
Supply cable(s) to the Load Center or Power Center must have a minimum current capacity
suitable for the intended load(s).
•
Supply circuit must be protected by suitable breaker rated no higher than 125 AMP.
High voltage
cover panel
attachment
screw holes
Spring latch
Front door
removal screw
GFCI knockout
(approved rainproof
cover required)
Low voltage
raceway
knockout
Expansion Center Enclosure
IntelliTouch Expansion Center Kit Installation Guide
4
Installing the Outdoor Control Panel
The Expansion Center Outdoor Control Panel includes a motherboard and Personality board. The
Personality board is mounted on top of the Motherboard which mounts on the back of the Outdoor
Control Panel. The Outdoor Control Panel installs in the top part of the Expansion Center.
To install the Outdoor Control Panel in the Expansion Center:
1. Unlatch the front door spring latches, and open the front door of the Expansion Center.
2. Remove the cover-panel screws securing the high voltage cover-panel, and remove it from
the enclosure.
3. Mount the Outdoor Control Panel in the top part of the Expansion Center. Secure it with two
access screws on the bottom edge of control panel. Once secured, the Outdoor Control
Panel can hinge out and down to access the Personality board for low voltage connections.
4. When finished with the relay, and transformer connections (see pages 6 through 9), close
the hinged Outdoor Control Panel and secure it with the two access screws.
5. Install the cover-panel and secure it with the two retaining screws.
6. Close the front door of the Expansion Center. Fasten the two spring latches.
Outdoor Control Panel
Access screw
Access screw
Cover-panel screw
(Cover-panel not shown)
Cover-panel screw
Retaining screw
Retaining screw
Expansion Center
IntelliTouch Expansion Center Kit Installation Guide
5
Connecting the Expansion Center Pre-Installed Relays
There are five pre-installed relays in the Expansion Center.
To connect the pre-installed relay cable plugs to the Personality board:
•
Route the power relay cable plugs up through the high voltage compartment to the
Personality Board. Insert the plug into the two-pin sockets, beginning with AUX1, then
AUX2, AUX3, AUX4, and AUX5. For the two-pin socket locations, refer to the diagram
shown below and the System Wiring Diagrams for models i5x, and i10x.
AUX1, AUX2,
AUX3, AUX4,
AUX5
Personality
Board
Feed each relay
cable plug up
through holes
IntelliTouch Expansion Center Kit Installation Guide
6
Installing Auxiliary Relays (Model i10x only)
Install additional Expansion Center axillary relays as needed. There may be as many as five
additional relays.
To install a relay:
1. At the Expansion Center, install the relays below the pre-installed relays. Secure in place
with two retaining screws.
2. Route the relay cable plug up through the holes into the high voltage compartment to the
Personality board.
3. Insert each auxiliary relay plug into the one of the two-pin sockets, beginning with AUX6,
AUX7, AUX8, AUX9 and AUX10 on the Personality board. For wiring details, refer to the
System Wiring Diagrams for model i10X page 10.
Personality Board
Relay Retaining
Screws
IntelliTouch Expansion Center Kit Installation Guide
Optional Relays (5x)
7
Connecting the Expansion Unit to the Load/Power Center
To connect a 4-wire cable from the Load Center or Power Center to the Personality board in the
Expansion enclosure:
1.
CAUTION - Switch the main power off at the Load Center or Power Center.
2. At the Load Center or Power Center, loosen the two access screws securing the Outdoor
Control Panel. Fold down the control panel to access the Personality board.
3. Insert one end of the 4-wire cable that connects the Expansion Center to the main Load
center or Power Center into plastic grommet on the bottom of the enclosure and route the
wire up through the low voltage raceway to the Personality board. Connect the wires to the
COM port (see page 8, step 5, 6, and 7 for details).
4. At the Expansion enclosure, Insert the 4-wire cable into plastic grommet on the bottom of
the enclosure and route the wire up through the low voltage raceway to the Personality
board. If necessary, for easier access to the raceway, remove the two screws securing the
high voltage panel cover, and remove it from the Expansion enclosure.
Outdoor Control Panel
Access screw
Access screw
Cover-panel screw
(Cover-panel not shown)
Cover-panel screw
Retaining screw
Retaining screw
Low voltage raceway
Plastic grommet
Expansion Center
IntelliTouch Expansion Center Kit Installation Guide
8
5. Strip back the cable conductors ¼ inch. Insert the wires into the either of the COM PORTS
(J7 and J8) screw terminals located on the left side of the Personality board. Secure the
wires with the screws. Make sure to match the color-coding of the wires: GND = Black,
Green = -DT, Yellow = +DT, and Red = +15 (see diagram below). For wiring details, refer to
the Wiring Diagram for models i5x and i10x (page 10). Note: Multiple wires may be inserted
into a single screw terminal.
6. Close the Expansion enclosure Outdoor Control Panel and secure it with the two access
screws.
7. If removed, install the high voltage panel cover and secure it with the two retaining screws.
Personality Board (Left-side)
Note: COM Ports can also be used for
connection to IntelliChlor and IntelliFlo
Personality
Board
Feed each relay
cable plug up
through holes
IntelliTouch Expansion Center Kit Installation Guide
9
Connecting the Expansion Center Transformer
To connect the Expansion Center transformer wire harness onto the Personality board:
•
Connect the transformer plug onto connector J2 on the right side of Personality board. The
plug is keyed onto the pins so that the six wires point towards back of the board. From left to
right the wire colors should be blue, orange, red. For the connector location, refer to the
diagram shown below and the System Wiring Diagram (page 10).
Note: The transformer terminals can be wired 115 VAC or 230 VAC. Refer to the System
Wiring Diagram for models i5x and i10x (see page 10 for wiring connections).
Affixing the System Wiring Diagram Label
To affix the wiring diagram label on the Expansion Center inside front door:
1. Open the Expansion Center front door.
2. Peel the backing off the wiring diagram label.
3. Position the label in middle of the inside of the front door. Apply even pressure on the surface
of the label to secure in place.
IntelliTouch Expansion Center Kit Installation Guide
10
System Wiring Diagram
(For models i5x and i10x)
IntelliTouch Expansion Center Kit Installation Guide
11
Glossary
Expansion Kit: A kit that includes additional auxiliaries to an existing Personality Kit. Requires a
Load Center for each Expansion Kit.
Feature Circuits: Programmable circuits that may control relays and/or valve actuators. For details
see the IntelliTouch Systems User’s Guide (P/N 520102)
High Voltage Compartment: Large lower right compartment of Load Center for all high voltage
wiring including circuit breakers, relays, and GFCI.
Indoor Control Panel: This fourteen button remote controller with LCD (liquid crystal display) is
wired to the Personality board in the Power/Load Center. The control panel can be wall mounted
inside a house to control IntelliTouch Systems.
iS4: Four function Spa-Side remote. Can be spa wall or deck mounted.
iS10: Up to ten function spa-side remote with temperature changing capability. Can be spa wall or
deck mounted.
Load Center: Metal enclosure with power relays, transformer, and circuit breakers. The Load Center
is Installed prior to Personality Kit installation. Used for distributing power for controlling IntelliTouch
Systems. Also known as the “sub-panel.”
Low Voltage Compartment: Top compartment of Load Center for all low voltage wiring.
Low Voltage Raceway: Vertical space in the left side of Power/Load Center for low voltage cabling.
MobileTouch Controller: Wireless controller for the IntelliTouch Systems with all the functionality of
the Indoor Control Panel.
Mud Box: Enclosure to provide mounting features for iS10 spa-side remote that is cast into gunite,
concrete, or other spa wall/deck construction.
Outdoor Control Panel: Control panel with flexible hinge installed in upper portion of Power/Load
Center to control IntelliTouch systems.
Personality Board: The circuit board mounted on top of the Outdoor Control Panel motherboard.
The Personality board defines the system capabilities.
Personality Kit: Set of parts to define the capability of a system; may include: Outdoor Control
Panel, temperature sensors, actuators, control panel (Indoor or MobileTouch), additional relays,
actuators.
Power Center: Same as Load Center with the exception of the circuit breaker base.
Relay Circuits: The circuits that control the relays on the Personality Board. Connectors on top
edge of the circuit board.
Terminal Connector: Removable connector that may attach to circuit board with multiple sockets
(anywhere from 2 to 12) to receive wires from controllers and sensors; wires held by screw
terminals; multiple wires of a small enough gauge (usually 22 AWG) may be coupled to a single
socket of a terminal connector.
Transceiver: Circuit board with attached antenna that can send and receive radio frequency
(wireless) transmissions.
IntelliTouch Expansion Center Kit Installation Guide
12
Notes
IntelliTouch Expansion Center Kit Installation Guide
P/N 520471 - Rev A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising