Safety and Compliance Information for Server

Safety and Compliance Information for Server
Safety and Compliance Information for
Server, Storage, Power, Networking, and
Rack Products
Abstract
This document contains safety precautions, environmental notices, and regulatory compliance notices for HP Enterprise products.
HP Part Number: 703827-002
Published: December 2012
Edition: 2
© Copyright 2012 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Contents
1 Safety precautions......................................................................................5
General precautions.................................................................................................................5
Symbols on equipment..............................................................................................................5
Precautions for maintaining and servicing products.......................................................................6
Precautions for power products...................................................................................................7
Power cords........................................................................................................................7
Power supplies.....................................................................................................................8
Uninterruptible power supply (UPS) products............................................................................8
Power distribution units (PDUs)...............................................................................................9
Grounding........................................................................................................................10
Voltage selection...............................................................................................................11
Batteries...........................................................................................................................11
Fuse replacement...............................................................................................................11
Precautions for products installed in racks and cabinets...............................................................11
Precautions for modems, telecommunications, or LAN options......................................................12
2 Environmental notices................................................................................13
Waste Electrical and Electronic Equipment (WEEE) statements......................................................13
Battery replacement notices.....................................................................................................14
RoHS material content declarations...........................................................................................17
China RoHS material content declaration..............................................................................17
Turkey RoHS material content declaration..............................................................................17
Ukraine RoHS material content declaration............................................................................17
Perchlorate material — Special handling may apply....................................................................17
3 Regulatory compliance notices...................................................................18
Regulatory compliance identification numbers............................................................................18
Federal Communications Commission notice..............................................................................18
FCC rating label................................................................................................................18
Class A equipment........................................................................................................18
Class B equipment........................................................................................................18
Declaration of Conformity for products marked with the FCC logo (United States only)................19
Modification.....................................................................................................................19
Cables.............................................................................................................................19
Notices for Canada (Avis Canadien).........................................................................................19
Class A equipment.............................................................................................................19
Class B equipment.............................................................................................................19
Notices for China...................................................................................................................19
Class A equipment.............................................................................................................19
Trusted Platform Module (TPM) – China Import Restrictions.......................................................20
Notices for European Union.....................................................................................................20
European Union regulatory notice........................................................................................20
European Union regulatory notice for wireless devices............................................................20
Notices for Japan...................................................................................................................22
VCCI notice......................................................................................................................22
Power cord statement..........................................................................................................22
Notices for Korea...................................................................................................................22
Class A equipment.............................................................................................................22
Class B equipment.............................................................................................................22
BSMI notice...........................................................................................................................23
Wireless devices.....................................................................................................................23
Brazilian notice.................................................................................................................23
Contents
3
Canadian notice................................................................................................................23
Japanese notice.................................................................................................................23
Taiwanese notice...............................................................................................................24
Laser compliance notices.........................................................................................................24
Index.........................................................................................................27
4
Contents
1 Safety precautions
Retain and follow all product safety and operating instructions. Always refer to the documentation
(printed or electronic) supplied with your product. If there is a conflict between this document and
the product documentation, the product documentation takes precedence. Observe all warnings
on the product and in the operating instructions to reduce the risk of bodily injury, electric shock,
fire, and damage to the equipment.
General precautions
CAUTION:
personnel.
The installation and maintenance of products must be carried out by qualified
If the product sustains damage requiring service, disconnect the product from the AC electrical
outlet and refer servicing to an HP authorized service provider. Examples of damage requiring
service include:
•
The power cord, extension cord, or plug has been damaged.
•
Liquid has been spilled on the product or an object has fallen into the product.
•
The product has been exposed to rain or water.
•
The product has been dropped or damaged.
•
The product does not operate normally when you follow the operating instructions.
To reduce the risk of personal injury or damage to the product:
•
Place the product away from radiators, heat registers, stoves, amplifiers, or other products
that produce heat.
•
Never use the product in a wet location.
•
Avoid inserting foreign objects through openings in the product.
•
Move products with casters carefully. Avoid quick stops and uneven surfaces.
•
Turn down the volume before using headphones or other audio devices.
Symbols on equipment
The following symbols may be placed on equipment to indicate the presence of potentially
hazardous conditions:
This symbol in conjunction with any of the following symbols indicates the presence of a potential
hazard. The potential for injury exists if warnings are not observed. Consult your documentation for
specific details.
This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all
servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure. Refer
all maintenance, upgrades, and servicing to qualified personnel.
This symbol indicates the presence of electric shock hazards. The area contains no user or
field-serviceable parts. Do not open for any reason.
WARNING: To reduce risk of injury from electric shock hazards, do not open this enclosure.
General precautions
5
This symbol on an RJ-45 receptacle indicates a Network Interface Connection.
WARNING: To reduce risk of electric shock, fire, or damage to the equipment, do not plug telephone
or telecommunications connectors into this receptacle.
This symbol indicates the presence of a hot surface or hot component. If this surface is contacted,
the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to cool before
touching.
This symbol indicates the presence of a moving fan blade. If the spinning blades are contacted, the
potential for injury exists.
WARNING: Hazardous moving parts. Keep away from moving fan blades. To reduce the risk of
injury from a hot component, allow the surface to cool before touching.
These symbols on power supplies or systems indicate that the equipment is supplied by multiple
sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power cords to completely
disconnect power from the system.
This symbol indicates that the component exceeds the recommended weight for one individual to
handle safely.
WARNING: To reduce the risk of personal injury or damage to the equipment, observe local
occupational health and safety requirements and guidelines for manual material handling.
A discharge of static electricity from a finger or other conductor may damage system boards or other
static-sensitive devices. To prevent damage, observe antistatic precautions.
This symbol indicates the presence of a laser device in the product that may exceed Class 1 limits.
Refer to the product documentation for more information.
Precautions for maintaining and servicing products
To reduce the risk of electric shock or damage to the equipment when installing, maintaining, or
servicing products, observe the following precautions:
6
•
Some products contain power supplies that are capable of producing hazardous energy levels.
Refer to the documentation included with your product to determine whether it contains these
power supplies. The installation of internal options and routine maintenance and service of
this product should be performed by individuals who are knowledgeable about the procedures,
precautions, and hazards associated with equipment containing hazardous energy levels.
•
Allow the product to cool before removing covers and touching internal components.
•
Do not use conductive tools that could bridge live parts.
•
Remove all watches, rings, or loose jewelry when working in hot-plug areas of an energized
server and storage products.
•
Do not attempt to defeat safety interlocks (where provided).
Safety precautions
•
Some products have covers or doors to access hot-plug components and may allow access
to hazardous energy circuits or moving fans.
◦
The doors should remain locked during normal operation.
OR
◦
The server should be installed in a controlled access location where only qualified
personnel have access to the server.
•
Power down the equipment and disconnect all AC power cords before removing any access
covers for non-hot-plug areas.
•
Do not replace non-hot-plug components while power is applied to the product. First, shut
down the product and disconnect all AC power cords.
•
Do not exceed the level of repair specified in the procedures in the product documentation.
All troubleshooting and repair procedures are detailed to allow only subassembly or
module-level repair. Because of the complexity of the individual boards and subassemblies,
do not attempt to make repairs at the component level or to make modifications to any printed
wiring board. Improper repairs can create a safety hazard.
•
For floor-standing products, install and extend bottom stabilizers before installing options and
boards.
•
Verify that the AC power supply branch circuit that provides power to the rack is not
overloaded. This will reduce the risk of personal injury, fire, or damage to the equipment. The
total rack load should not exceed 80 percent of the branch circuit rating. Consult the electrical
authority having jurisdiction over your facility wiring and installation requirements.
Precautions for power products
Power cords
To reduce the risk of electric shock or damage to the equipment:
•
Use an approved power cord. If you have questions about the type of power cord to use,
contact your HP authorized service provider.
•
If you have not been provided with a power cord for your computer or for any AC-powered
option intended for your product, purchase a power cord that is approved for use in your
country.
•
You must use a power cord rated for your product and for the voltage and current marked on
the electrical ratings label of the product. The voltage and current rating of the cord must be
greater than the voltage and current rating marked on the product.
•
Do not place objects on AC power cords or cables. Arrange them so that no one may
accidentally step on or trip over them.
•
Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord
by the plug.
•
Make sure that the total ampere rating of all products plugged into an extension cord or power
strip does not exceed 80 percent of the ampere ratings limit for the extension cord or power
strip.
•
Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
•
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
Precautions for power products
7
Power supplies
Hot-plug power supplies are not designed to be removed or installed with AC power connected
to the power supply. To reduce the risk of electric shock or damage to the equipment when handling
hot-plug power supplies:
•
Install the power supply before connecting the power cord to the power supply.
•
Unplug the power cord before removing the power supply from the product.
•
If the system has multiple sources of power, you must unplug all AC power cords from the
power supplies to completely disconnect power from the system.
Verify that the external power source connected to your product matches the type of power source
indicated on the electrical ratings label. If you are not sure of the type of power source required,
consult your HP authorized service provider or local power company.
Uninterruptible power supply (UPS) products
•
To reduce the risk of electric shock and/or equipment damage when installing or servicing
UPS products:
◦
The installation of options and routine maintenance and service of UPS products must be
performed by trained service technicians who are knowledgeable about the procedures,
precautions, and hazards associated with AC power products.
◦
Hardwired UPS products require a direct connection to a dedicated AC branch circuit
(AC mains). Connection should only be performed by a licensed electrician in accordance
with National Electrical Code (NFPA70) Article 310 in North America or the equivalent
local and national wiring regulations.
◦
Use a Lockout/Tagout procedure to isolate hardwired UPS products from AC power
before servicing the product or replacing a non-hot-plug component.
◦
Do not operate a UPS that is disconnected from AC power. Use the TEST/ALARM RESET
button to test the batteries. Disconnect all protected loads before disconnecting the UPS
from AC power.
◦
Pluggable UPS products must be disconnected and unplugged from AC power before
servicing the product or replacing a non-hot-plug component.
◦
Do not overload the output of the UPS. The total connected load should not exceed the
rated output.
◦
To reduce the risk of electric shock due to high leakage currents, ensure that there is a
reliable grounded (earthed) connection before connecting power distribution products to
AC power.
If a large number of products will be connected to a single UPS, it may be necessary to
conduct an evaluation of the installation to verify the total amount of leakage current. The
total combined leakage current should not exceed 5 percent of the input current for the
UPS and associated load.
8
Safety precautions
•
•
•
◦
For rack installations, do not exceed the maximum number of UPS products in any single
equipment rack.
◦
For rack installations, install the UPS only at the bottom of a rack.
To reduce the risk of personal injury or damage to equipment when installing a Remote
Emergency Power Off (REPO) port:
◦
The REPO port must be wired by a licensed electrician.
◦
Verify that the main AC power disconnect device for the UPS is locked and/or tagged
in the OFF position before wiring the REPO port.
◦
In North America, the REPO circuit must comply with the NEC (NFPA 70, Article 725)
for a Class 2 circuit. In other geographical regions or countries, the REPO port wiring
must comply with the national and local standards in the area in which the product is
installed.
To reduce the risk of personal injury from electric shock or damage to equipment when installing
or servicing batteries:
◦
Make sure that only trained service personnel handle or connect the batteries.
◦
Remove watches, rings, or other metal objects prior to working with the equipment.
◦
Use tools with insulated handles.
◦
On products with remote external batteries, do not attempt to replace batteries unless all
battery circuit breakers are in the OFF (down) position. These are hazardous voltage
batteries.
This product may contain sealed lead-acid batteries. To reduce the risk of fire or chemical
burns:
◦
Do not attempt to recharge batteries after they have been removed from the equipment.
◦
Do not disassemble, crush, or puncture the batteries.
◦
Do not short the external contacts of the batteries.
◦
Do not immerse the batteries in water.
◦
Do not expose the batteries to temperatures higher than 60°C or dispose of in fire.
◦
Use only the HP spare battery designated for this equipment.
Power distribution units (PDUs)
To reduce the risk of electric shock and/or equipment damage when installing or servicing PDUs:
•
The installation and routine maintenance and service of PDUs must be performed by trained
service technicians who are knowledgeable about the procedures, precautions, and hazards
associated with AC power products.
•
Hardwired PDUs require a direct connection to a dedicated AC branch circuit (AC mains).
Connection should only be performed by a licensed electrician in accordance with National
Electrical Code (NFPA70 Article 310) in North America, or in other regions or countries, in
accordance with the equivalent local and national wiring regulations.
•
A reliable grounded (earthed) connection should be checked before connecting PDUs.
•
Use a Lockout/Tagout procedure to isolate hardwired PDUs from AC power before servicing
or replacing the product.
Precautions for power products
9
•
Pluggable PDUs must be disconnected from the product and unplugged from the AC electrical
outlet before servicing or replacing the product.
•
Do not overload the output of PDUs. The total connected load should not exceed rated input
power.
•
To reduce the risk of electric shock due to high leakage currents, ensure that there is a reliable
grounded (earthed) connection before connecting power distribution products to AC power.
If a large number of products will be connected to a single PDU, it may be necessary to conduct
an evaluation of the installation to verify the total amount of leakage current. The total combined
leakage current should not exceed 5 percent of the input current for the PDU and associated
load.
Grounding
Depending on the product model, your product will be classified either as a safety Class I or safety
Class II-compliant device. Class I devices require a connection to earth ground (3-terminal plug);
Class II devices incorporate a 2-terminal plug.
•
Class I: There must be an uninterruptible safety earth ground from the main power source to
the product's power cord or supplied power cord set. Whenever it is likely that the protection
has been impaired, disconnect the power cord until the ground has been restored.
•
Class II: Safety Class II-compliant devices include supplemental insulation to protect against
electric shock, and do not require a connection to earth ground.
For LAN connections:
•
If your LAN covers an area served by more than one power distribution system, be sure their
safety grounds are securely interconnected.
•
LAN cables may occasionally be subject to hazardous transient voltages (such as lightning
or disturbances in the electrical utilities power grid). Handle exposed metal components of
the network with caution.
•
This product and all interconnected equipment must be installed indoors within the same
building, including all associated LAN connections as described by Environment A of the IEEE
802.3af standard.
Earth leakage current
To reduce the risk of electric shock due to high leakage currents, ensure that there is a reliable
grounded (earthed) connection before connecting power distribution products to AC power.
Observe the following limits when connecting the product to AC power distribution devices:
•
For UPS products and PDUs that have attached AC power cords or are directly wired to the
building power, the total combined leakage current should not exceed 5 percent of the rated
input current for the device.
•
For UPS products and PDUs that have detachable AC power cords, the total combined leakage
current should not exceed 3.5mA.
Electrostatic discharge (ESD)
When handling any electronic component or assembly (such as a PCI card or memory DIMM),
you must observe the following antistatic precautions to prevent damage. An ESD kit (HP P/N
A3024-80004) is available (or supplied with memory additions). This kit contains one wrist strap,
one conductive sheet, and one antistatic foam pad.
10
•
Always disconnect power from the server and wear a grounded wrist strap when working
around the server.
•
Always wear a grounded wrist strap when handling printed circuit boards.
Safety precautions
•
Treat all assemblies, components, and interface connections as static sensitive.
•
Avoid working in carpeted areas and keep body movement to a minimum while removing or
installing boards to minimize buildup of static charge.
Voltage selection
•
On products that have voltage select switches, make sure that the switch is set for the type of
voltage you use (115 VAC or 230 VAC).
•
Do not attempt to power the product with voltage converter kits sold for appliances.
Batteries
WARNING! Some HP products may contain internal replaceable battery cells or battery packs.
There is risk of fire and burns if the battery pack is not handled properly. To reduce the risk of
personal injury:
•
Do not attempt to recharge the battery.
•
Do not disassemble, crush, puncture, short external contacts, or dispose of the battery in fire
or water.
•
Replace only with the HP spare battery designated for this product. Dispose of used batteries
according to the manufacturer's instructions and local disposal requirements.
•
For battery holders (for example, coin cells), observe the correct polarity when changing the
battery/cell. There is a danger of explosion if the battery is installed incorrectly.
Fuse replacement
CAUTION: For continued protection against risk of fire, replace fuses only with fuses of the same
type and the same rating. Disconnect power before changing fuses.
Precautions for products installed in racks and cabinets
Materials handling
To reduce the risk of personal injury or damage to the equipment:
•
Observe local occupational health and safety requirements and guidelines for handling
materials.
•
Obtain assistance to lift and stabilize the product during installation or removal.
•
Remove all pluggable power supplies and modules to reduce the weight of the product.
•
Be careful when pressing the rail release latches and sliding the product into the rack. The
slide rails could pinch your fingertips.
Rack stability
To reduce the risk of personal injury or damage to the equipment, the rack must be secured
adequately to prevent it from becoming unstable and/or falling over.
•
Extend the leveling jacks to the floor.
•
Ensure that the full weight of the rack rests on the leveling jacks.
•
Install stabilizing feet on the rack.
•
In a multiple-rack installation, fasten the racks together securely.
•
Extend only one rack component at a time. Racks can become unstable if more than one
component is extended.
Precautions for products installed in racks and cabinets
11
•
Load the rack from the bottom up, starting with the heaviest component.
•
Ensure that the component is properly mated with the rails, or the rails may be unstable.
•
Do not attempt to move a fully loaded rack. Remove components from the rack before moving
it.
•
Do not attempt to move a rack on an incline that is greater than 10 degrees from horizontal.
Cabinet safety
WARNING! Cabinets are heavy even when empty. Exercise caution when moving cabinets
whether equipment is installed in the cabinet or not. Avoid rolling cabinets on rough or uneven
surfaces or inclines greater than 10 degrees. Unloading cabinets from the pallet and movement
of cabinets should be performed by at least two people.
Slideable products are not to be extended from the cabinet while the equipment is on the shipping
pallet. The cabinet must be unloaded from the pallet and all anti-tip devices properly installed prior
to extending any slideable product.
Once installed, all anti-tip devices must remain in place to maintain stability. Only one slideable
product must be extended at a time.
For more information on ballast requirements, see http://h20195.www2.hp.com/V2/GetPDF.aspx/
4AA2-7573ENW.pdf .
Failure to follow these precautions can result in damage to equipment or injury to personnel.
Precautions for modems, telecommunications, or LAN options
To reduce the risk of exposure to shock from telephone ringing voltages:
12
•
Do not connect or use a modem or telephone (other than a cordless type) during a lightning
storm.
•
Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.
•
Do not connect or use a modem or telephone cable in a wet location.
•
Disconnect the modem cable before opening a product enclosure, touching or installing internal
components, or touching an uninsulated modem cable or jack.
•
Do not plug telecommunications or telephone connectors into the NIC receptacles.
Safety precautions
2 Environmental notices
HP is committed to providing our customers with information about the chemical substances in our
products as needed to comply with legal requirements such as REACH (Regulation EC No
1907/2006 of the European Parliament and the Council). A chemical information report for this
product can be found at http://www.hp.com/go/reach.
For HP product environmental and safety information and compliance data, including RoHS and
REACH, see www.hp.com/go/ecodata.
For HP environmental information, including company programs, product recycling, and energy
efficiency, see www.hp.com/environment.
Waste Electrical and Electronic Equipment (WEEE) statements
Country
EU WEEE Directive Page
Austria
http://h41111.www4.hp.com/globalcitizenship/at/de/environment/recycle/hardwarerecycle.html
Belgium (FR)
http://h41111.www4.hp.com/globalcitizenship/be/fr/environment/recycle/hardwarerecycle.html
Belgium (NL)
http://h41111.www4.hp.com/globalcitizenship/be/nl/environment/recycle/hardwarerecycle.html
Bulgaria
http://h41111.www4.hp.com/globalcitizenship/bg/bg/environment/recycle/hardwarerecycle.html
Czech Republic
http://h41111.www4.hp.com/globalcitizenship/cz/cs/environment/recycle/hardwarerecycle.html
Denmark
http://h41111.www4.hp.com/globalcitizenship/dk/da/environment/recycle/hardwarerecycle.html
Estonia
http://h41111.www4.hp.com/globalcitizenship/ee/et/environment/recycle/hardwarerecycle.html
Finland
http://h41111.www4.hp.com/globalcitizenship/fi/fi/environment/recycle/hardwarerecycle.html
France
http://h41111.www4.hp.com/globalcitizenship/fr/fr/environment/recycle/hardwarerecycle.html
Germany
http://h41111.www4.hp.com/globalcitizenship/de/de/environment/recycle/hardwarerecycle.html
Greece
http://h41111.www4.hp.com/globalcitizenship/gr/el/environment/recycle/hardwarerecycle.html
Hungary
http://h41111.www4.hp.com/globalcitizenship/hu/hu/environment/recycle/hardwarerecycle.html
Ireland
http://h41111.www4.hp.com/globalcitizenship/ie/en/environment/recycle/hardwarerecycle.html
Italy
http://h41111.www4.hp.com/globalcitizenship/it/it/environment/recycle/hardwarerecycle.html
Latvia
http://h41111.www4.hp.com/globalcitizenship/lv/lv/environment/recycle/hardwarerecycle.html
Lithuania
http://h41111.www4.hp.com/globalcitizenship/lt/lt/environment/recycle/hardwarerecycle.html
Luxembourg
http://h41111.www4.hp.com/globalcitizenship/be/fr/environment/recycle/hardwarerecycle.html
Malta
http://h41111.www4.hp.com/globalcitizenship/uk/en/environment/recycle/hardwarerecycle.html
Netherlands
http://h41111.www4.hp.com/globalcitizenship/nl/nl/environment/recycle/hardwarerecycle.html
Norway
http://h41111.www4.hp.com/globalcitizenship/no/no/environment/recycle/hardwarerecycle.html
Poland
http://h41111.www4.hp.com/globalcitizenship/pl/pl/environment/recycle/hardwarerecycle.html
Portugal
http://h41111.www4.hp.com/globalcitizenship/pt/pt/environment/recycle/hardwarerecycle.html
Romania
http://h41111.www4.hp.com/globalcitizenship/ro/ro/environment/recycle/hardwarerecycle.html
Slovakia
http://h41111.www4.hp.com/globalcitizenship/sk/sk/environment/recycle/hardwarerecycle.html
Slovenia
http://h41111.www4.hp.com/globalcitizenship/si/sl/environment/recycle/hardwarerecycle.html
Spain
http://h41111.www4.hp.com/globalcitizenship/es/es/environment/recycle/hardwarerecycle.html
Waste Electrical and Electronic Equipment (WEEE) statements
13
Country
EU WEEE Directive Page
Sweden
http://h41111.www4.hp.com/globalcitizenship/se/sv/environment/recycle/hardwarerecycle.html
Switzerland (DE) http://h41111.www4.hp.com/globalcitizenship/ch/de/environment/recycle/hardwarerecycle.html
Switzerland (FR) http://h41111.www4.hp.com/globalcitizenship/ch/fr/environment/recycle/hardwarerecycle.html
United Kingdom http://h41111.www4.hp.com/globalcitizenship/uk/en/environment/recycle/hardwarerecycle.html
Battery replacement notices
Batteries, battery packs, and accumulators should not be disposed of together with the general household
waste. To forward them to recycling or proper disposal, use the public collection system or return them
to HP, an authorized HP Partner, or their agents.
For more information about battery replacement or proper disposal, contact an authorized reseller or
an authorized service provider.
14
Environmental notices
Battery replacement notices
15
16
Environmental notices
RoHS material content declarations
China RoHS material content declaration
Chinese version:
http://www8.hp.com/us/en/hp-information/environment/chinarohs.html
English version:
http://www8.hp.com/us/en/hp-information/environment/chinarohs-english.html
Turkey RoHS material content declaration
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur
Ukraine RoHS material content declaration
Обладнання відповідає вимогам Технічного регламенту щодо обмеження використання деяких
небезпечних речовин в електричному та електронному обладнанні, затвердженого постановою
Кабінету Міністрів України від 3 грудня 2008 № 1057
Perchlorate material — Special handling may apply
Perchlorate material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/
perchlorate/.
This product’s real-time clock battery or coin cell battery may contain perchlorate and may require
special handling when recycled or disposed of in California.
RoHS material content declarations
17
3 Regulatory compliance notices
Regulatory compliance identification numbers
For the purpose of regulatory compliance certifications and identification, this product has been
assigned a unique regulatory model number. The regulatory model number can be found on the
product nameplate label, along with all required approval markings and information. When
requesting compliance information for this product, always refer to this regulatory model number.
The regulatory model number is not the marketing name or model number of the product.
Federal Communications Commission notice
Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established
Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum.
Many electronic devices, including computers, generate RF energy incidental to their intended
function and are, therefore, covered by these rules. These rules place computers and related
peripheral devices into two classes, A and B, depending upon their intended installation. Class A
devices are those that may reasonably be expected to be installed in a business or commercial
environment. Class B devices are those that may reasonably be expected to be installed in a
residential environment (for example, personal computers). The FCC requires devices in both classes
to bear a label indicating the interference potential of the device as well as additional operating
instructions for the user.
FCC rating label
The FCC rating label on the device shows the classification (A or B) of the equipment. Class B
devices have an FCC logo or ID on the label. Class A devices do not have an FCC logo or ID on
the label. After you determine the class of the device, refer to the corresponding statement.
Class A equipment
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at personal expense.
Class B equipment
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
18
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit that is different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio or television technician for help.
Regulatory compliance notices
Declaration of Conformity for products marked with the FCC logo (United States only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
For questions regarding this product, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
•
1-800-HP-INVENT (1-800-474-6836)
For continuous quality improvement, calls may be recorded or monitored.
For questions regarding this FCC declaration, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
•
1-281-514-3333
To identify the product, refer to the part, series, or model number found on the product.
Modification
The FCC requires the user to be notified that any changes or modifications made to this device
that are not expressly approved by Hewlett-Packard Company may void the user's authority to
operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector
hoods in order to maintain compliance with FCC Rules and Regulations.
Notices for Canada (Avis Canadien)
Class A equipment
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la class A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Class B equipment
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la class B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Notices for China
Class A equipment
Notices for Canada (Avis Canadien)
19
Trusted Platform Module (TPM) – China Import Restrictions
HP SPECIAL REMINDER: Before enabling TPM functionality on this system, you must ensure that
your intended use of TPM complies with relevant local laws, regulations and policies, and approvals
or licenses must be obtained if applicable.
For any compliance issues arising from your operation/usage of TPM which violates the above
mentioned requirement, you shall bear all the liabilities wholly and solely. HP will not be responsible
for any related liabilities.
Notices for European Union
European Union regulatory notice
Products bearing the CE marking comply with the following EU Directives:
•
Low Voltage Directive 2006/95/EC
•
EMC Directive 2004/108/EC
•
Ecodesign Directive 2009/125/EC, where applicable
•
RoHS Directive 2011/65/EU
CE compliance of this product is valid if powered with the correct CE-marked AC adapter provided
by HP.
Compliance with these directives implies conformity to applicable harmonized European standards
(European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product
or product family and available (in English only) either within the product documentation or at the
following HP website: http://www.hp.eu/certificates (type the product number in the search field).
The compliance is indicated by the following conformity marking placed on the product:
Please refer to the regulatory label provided on the product.
The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE,
Herrenberger Strasse 140, 71034 Boeblingen, GERMANY.
European Union regulatory notice for wireless devices
Products bearing the CE marking comply with the following EU Directives:
•
Low Voltage Directive 2006/95/EC
•
EMC Directive 2004/108/EC
•
Ecodesign Directive 2009/125/EC, where applicable
•
RoHS Directive 2011/65/EU
CE compliance of this product is valid if powered with the correct CE-marked AC adapter provided
by HP.
20
Regulatory compliance notices
If this product has wired and/or wireless telecommunications functionality, it also complies with
the essential requirements of the following EU Directive:
•
R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to the applicable harmonized European
standards (European Norms) that are listed in the EU Declaration of Conformity issued by HP for
this product or product family and available (in English only) either within the product documentation
or at the following HP website: http://www.hp.eu/certificates (type the product number in the
search field).
The compliance is indicated by the following conformity marking placed on the product:
Please refer to the regulatory label provided on the product.
The telecommunications functionality of this product may be used in the following EU and EFTA
countries: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg,
Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain,
Sweden, Switzerland, and United Kingdom.
The telephone connector (not available for all products) is intended for connection to analogue
telephone networks.
Products with wireless LAN devices:
Some countries may have specific obligations or special requirements about the operation of
Wireless LAN networks such as indoor use only or restrictions of the channels available. Please
make sure that the country settings of the wireless network are correct.
France:
For 2.4 GHz Wireless LAN operation of this product, certain restrictions apply: This product may
be used indoors for the entire 2400-MHz to 2483.5-MHz frequency band (channels 1 to 13). For
outdoor use, only the 2400-MHz to 2454-MHz frequency band (channels 1 to 7) may be used.
For the latest requirements, see the ARCEP website: http://www.arcep.fr.
The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE,
Herrenberger Strasse 140, 71034 Boeblingen, GERMANY.
Notices for European Union
21
Notices for Japan
VCCI notice
Power cord statement
Notices for Korea
Class A equipment
Class B equipment
22
Regulatory compliance notices
BSMI notice
Wireless devices
In some environments, the use of wireless devices might be restricted. Such restrictions might apply
on airplanes, in hospitals, near explosives, or in other hazardous locations. Before you turn on
this product, be sure that you understand local policies and have proper authorization.
WARNING! Exposure to Radio Frequency Radiation: The radiated output power of this device
is below the FCC radio exposure limits. Nevertheless, the device should be used in such a manner
that the potential for human contact during normal operation is minimized. To avoid the possibility
of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should
not be less than 20 cm (8 inches) during normal operation.
Brazilian notice
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra
interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a
sistemas operando em caráter primário.
Canadian notice
Wireless operation is subject to two conditions. The first is that the wireless device may not cause
interference. The second is that the wireless device must accept any interference, including
interference that may cause undesired operation of the device.
Japanese notice
BSMI notice
23
Taiwanese notice
Laser compliance notices
This device may contain a laser that is classified as a Class 1 Laser Product in accordance with
U.S. FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation.
WARNING! Use of controls or adjustments or performance of procedures other than those
specified herein or in the laser product's installation guide may result in hazardous radiation
exposure. To reduce the risk of exposure to hazardous radiation:
•
Do not try to open the module enclosure. There are no user-serviceable components inside.
•
Do not operate controls, make adjustments, or perform procedures to the laser device other
than those specified herein.
•
Allow only HP Authorized Service technicians to repair the unit.
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration
implemented regulations for laser products on August 2, 1976. These regulations apply to laser
products manufactured from August 1, 1976. Compliance is mandatory for products marketed in
the United States.
24
Regulatory compliance notices
Laser compliance notices
25
26
Regulatory compliance notices
Index
B
batteries
replacement notices, 14
safety precautions, 9, 11
BSMI notice, 23
C
cabinet safety, 12
CE compliance marking, 20
China import restrictions
Trusted Platform Module (TPM), 20
China RoHS material content declaration, 17
D
Declaration of Conformity
European Union, 20
products marked with FCC logo (U.S. only), 19
E
earth leakage current, 10
electromagnetic interference (EMI)
cable connector hoods, 19
electrostatic discharge (ESD), 10
EMC compliance notices, 18
environmental notices, 13
battery replacement and disposal, 14
perchlorate, 17
REACH, 13
RoHS, 13
WEEE, 13
equipment symbols, 5
ESD kit, 10
European Union Declaration of Conformity, 20
European Union regulatory notice, 20
for wireless devices, 20
F
FCC notice, 18
FCC rating label, 18
Class A equipment, 18
Class B equipment, 18
fuse replacement, 11
G
grounding
earth leakage current, 10
ESD, 10
safety precautions, 10
L
laser compliance notices, 24
M
maintaining and servicing products
safety precautions, 6
materials handling
products installed in racks and cabinets, 11
modems
safety precautions, 12
P
perchlorate material
safety precautions, 17
power cords
safety precautions, 7
power distribution units (PDUs)
safety precautions, 9
power supplies
safety precautions, 8
products installed in racks and cabinets
materials handling, 11
safety precautions, 11
R
rack stability, 11
radio frequency (RF) emission limits
FCC notice, 18
radio frequency interference (RFI)
cable connector hoods, 19
REACH, 13
recycling notices, 13
regulatory compliance identification numbers, 18
regulatory compliance notices, 18
BSMI, 23
Canada (Avis Canadien), 19
China, 19
European Union, 20
FCC, 18
identification numbers, 18
Japan, 22
Korea, 22
laser notices, 24
recycling notices, 13
WEEE statements, 13
wireless devices, 23
regulatory model number, 18
Remote Emergency Power Off (REPO) port
safety precautions, 9
RoHS material content declarations
China, 17
Turkey, 17
Ukraine, 17
S
safety precautions, 5
batteries, 9, 11
cabinets, 12
fuse replacement, 11
general, 5
grounding, 10
maintaining and servicing products, 6
27
modems, 12
modems, telecommunications, or LAN options, 12
PDUs, 9
power cords, 7
power products, 7
power supplies, 8
products installed in racks and cabinets, 11
REPO port, 9
telecommunications equipment, 12
UPS, 8
voltage selection, 11
substances
environmental notices, 13
perchlorate material, 17
RoHS material content declarations, 17
symbols on equipment, 5
T
telecommunications equipment
safety precautions, 12
Trusted Platform Module (TPM)
China import restrictions, 20
Turkey RoHS material content declaration, 17
U
Ukraine RoHS material content declaration, 17
UPS products
safety precautions, 8
V
VCCI notice, 22
voltage selection, 11
W
WEEE statements, 13
wireless devices, 23
Brazilian notice, 23
Canadian notice, 23
European Union regulatory notice, 20
Japanese notice, 23
Taiwanese notice, 24
28
Index
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising