Ikelite
Ikelite
EX TERN AL CO LO R-CO RR ECTIO N FIL TERS
External Color-Correction Filters
I n s t a l l a t i o n
I n s t r u c t i o n s
Vent
Filter Holder
Push-Fit Filter
Holder Over
Housing Port
Vent
Color
Filter
Color
Filter
Color
Filter
Filter
Holder
Filter
Holder
Lanyard
Attachment
Holes
Lanyard
Attachment
Loop
Vent
Lanyard
Attachment
Ring
Color
Filter
Ikelite’s Color-Correction Filters are
secured in a rubber Filter Holder that is a push-fit
over the housing port on digital still or video housings.
Filters can also be used on the Ikelite W-20 and WP-80 wide-angle
accessory lenses. The red filter is for tropical (blue) water and the
magenta filter is for cold (green) water. The filters enhance the
color balance in natural light photography. Useful to depths of
approx. 24m (80’), subject to sufficient available light. Filter use is
not recommended above water or with flash.
Push-Fit Filter
Holder Over
Accessory Lens
Filter
Holder
2
Note: Please read all instructions before using this product.
INSTRUCTIONS
Installation:
The External Color Filter secures over the front of the housing
port or accessory lens. If not attached, attach the lanyard to the
Filter Holder. Attach the small end of the Lanyard to the
Lanyard Attachment on the Filter Holder. Slide the large end of
the lanyard through the small end loop, and pull tight. Open
large end of the lanyard and place over the housing handle so
that the lanyard and color filter hang safely from the housing
tray. When ready to use, push the filter over the housing port or
accessory lens. This will be easier to do underwater and it is
recommended that you always install the filter underwater.
Cleaning:
The external filter is protected with a scratch resistant coating.
Special care should always be taken when handling. Immediately
after use, rinse and gently dry the filter to avoid water spotting.
If necessary, use a mild non-abrasive soap solution or lens
cleaner, and a very soft cloth to clean the filter. Minor scratches
will usually fill with water and not affect the picture quality.
Usage:
If you enter the water with the filter secured on the port or
accessory lens, you will need to remove the filter underwater to
gently remove any trapped air bubbles. You can then re-install
the filter.
It is extremely important that no air bubbles are trapped
between the port or accessory lens and filter. The camera may
focus on any trapped bubbles resulting in an out-of-focus image.
NOTE:
For best results do not shoot directly into sunlight.
3
Accessory Lens
Ikelite Limited Warranty
All Ikelite products are warranted against any manufacturing
defects for a period of one year from the date of purchase.
Defective products should be returned prepaid to Ikelite. Ikelite
will, at its discretion, repair or replace such products, and will
return to customer prepaid. All other claims, of any nature,
including, but not limited to, bulb failure are not covered. Except
as mentioned above, no other warranty, expressed or implied,
applies to this Ikelite product.
Returning Products for Service
Ikelite is most interested in performing any service to assure
that all products perform as intended. For repair or service, return
the product to the address below with your name, address, phone
number and a brief description of the problem. Evidence of
purchase date must be provided to obtain warranty service.
Ikelite Underwater Systems
Attn: Repair Department
50 W 33rd Street
Indianapolis, IN 46208 USA
317-923-4523
email: ikelite@ikelite.com
www.ikelite.com
UR-Pro-01-0 209
EXT ERN AL CO LOR -CO RR ECT IO N FILT ERS
Filter Holder
Push-Fit Filter
Metal Holder
Over Housing
Port
Color
Filter
Ikelite’s Color-Correction Filters are
secured in a rubber Filter Holder that is a push-fit
over the housing port on digital still or video housings.
Filters can also be used on the Ikelite W-20 and WP-80 wide-angle
lenses. The red filter is for tropical (blue) water and the magenta
filter is for cold (green) water. The filters enhances the color
balance in natural light photography. Useful to depths of approx.
24m (80’), subject to sufficient available light. Filter use is not
recommended above water or with flash.
Push-Fit Filter
Holder Over
Accessory Lens
INSTRUCTIONS
Installation:
The External Color Filter secures over the front of the housing
port or accessory lens. If not attached, attach the lanyard to the
Filter Holder. Attach the small end of the Lanyard to the
Lanyard Attachment on the Filter Holder. Slide the large end of
the lanyard through the small end loop, and pull tight. Open
large end of the lanyard and place over the housing handle so
that the lanyard and color filter hang safely from the housing
tray. When ready to use, push the filter over the housing port or
accessory lens. This will be easier to do underwater and it is
recommended that you always install the filter underwater.
Cleaning:
The external filter is protected with a scratch resistant coating.
Special care should always be taken when handling. Immediately
after use, rinse and gently dry the filter to avoid water spotting.
If necessary, use a mild non-abrasive soap solution or lens
cleaner, and a very soft cloth to clean the filter. Minor scratches
will usually fill with water and not affect the picture quality.
Usage:
If you enter the water with the filter secured on the port or w/a
lens, you will need to remove the filter underwater to gently
remove any trapped air bubbles. You can then re-install the
filter. It is extremely important that no air bubbles are trapped
between the port or w/a lens and filter.
Light Refraction:
Do not shoot into the sun while using the external color filter
because it may create a noticeable refraction effect.
3
2
EXT ERN AL CO LOR -CO RR ECT IO N FILT ERS
Filter Holder
Push-Fit Filter
Metal Holder
Over Housing
Port
Color
Filter
Ikelite’s Color-Correction Filters are
secured in a rubber Filter Holder that is a push-fit
over the housing port on digital still or video housings.
Filters can also be used on the Ikelite W-20 and WP-80 wide-angle
lenses. The red filter is for tropical (blue) water and the magenta
filter is for cold (green) water. The filters enhances the color
balance in natural light photography. Useful to depths of approx.
24m (80’), subject to sufficient available light. Filter use is not
recommended above water or with flash.
Push-Fit Filter
Holder Over
Accessory Lens
2
INSTRUCTIONS
Installation:
The External Color Filter secures over the front of the housing
port or accessory lens. If not attached, attach the lanyard to the
Filter Holder. Attach the small end of the Lanyard to the
Lanyard Attachment on the Filter Holder. Slide the large end of
the lanyard through the small end loop, and pull tight. Open
large end of the lanyard and place over the housing handle so
that the lanyard and color filter hang safely from the housing
tray. When ready to use, push the filter over the housing port or
accessory lens. This will be easier to do underwater and it is
recommended that you always install the filter underwater.
Cleaning:
The external filter is protected with a scratch resistant coating.
Special care should always be taken when handling. Immediately
after use, rinse and gently dry the filter to avoid water spotting.
If necessary, use a mild non-abrasive soap solution or lens
cleaner, and a very soft cloth to clean the filter. Minor scratches
will usually fill with water and not affect the picture quality.
Usage:
If you enter the water with the filter secured on the port or w/a
lens, you will need to remove the filter underwater to gently
remove any trapped air bubbles. You can then re-install the
filter. It is extremely important that no air bubbles are trapped
between the port or w/a lens and filter.
Light Refraction:
Do not shoot into the sun while using the external color filter
because it may create a noticeable refraction effect.
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising