600 A 15 kV, 25 kV and 35 kV class bushing extender installation

600 A 15 kV, 25 kV and 35 kV class bushing extender installation
Deadbreak Apparatus
Connectors
MN650053EN
COOPER POWER
Effective May 2017
Supersedes January 2009 (S600-59-3)
600 A 15 kV, 25 kV and 35 kV class bushing
extender installation instructions
SERIES
DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY
The information, recommendations, descriptions and safety notations in this document are based on Eaton Corporation’s
(“Eaton”) experience and judgment and may not cover all contingencies. If further information is required, an Eaton sales
office should be consulted. Sale of the product shown in this literature is subject to the terms and conditions outlined in
appropriate Eaton selling policies or other contractual agreement between Eaton and the purchaser.
THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES
OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY
EXISTING CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE OBLIGATION OF EATON. THE
CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES.
In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or
other-wise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to
damage or loss of use of equipment, plant or power system, cost of capital, loss of power, additional expenses in the use of
existing power facilities, or claims against the purchaser or user by its customers resulting from the use of the information,
recommendations and descriptions contained herein. The information contained in this manual is subject to change
without notice.
INSTALLATION INSTRUCTIONS MN650053EN May 2017
i
Contents
DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I
SAFETY FOR LIFE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . III
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . III
Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
PRODUCT INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Read this manual first. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Acceptance and initial inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Handling and storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bushing extender kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installation instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ii
INSTALLATION INSTRUCTIONS MN650053EN May 2017
!
SAFETY
FOR LIFE
Safety for life
!
SAFETY
FOR LIFE
Eaton’s Cooper Power series products meet or exceed all applicable industry standards relating to product safety. We
actively promote safe practices in the use and maintenance of our products through our service literature, instructional
training programs, and the continuous efforts of all Eaton employees involved in product design, manufacture, marketing
and service.
We strongly urge that you always follow all locally approved safety procedures and safety instructions when working around
high-voltage lines and equipment and support our “Safety For Life” mission.
Safety information
The instructions in this manual are not intended as a
sub­stitute for proper training or adequate experience in the
safe operation of the equipment described. Only competent
technicians, who are familiar with this equipment should
install, operate and service it.
A competent technician has these qualifications:
• Is thoroughly familiar with these instructions.
• Is trained in industry-accepted high- and low-voltage safe
operating practices and procedures.
• Is trained and authorized to energize, de-energize, clear,
and ground power distribution equipment.
• Is trained in the care and use of protective equipment
such as flash clothing, safety glasses, face shield, hard
hat, rubber gloves, hotstick, etc.
Following is important safety information. For safe installation
and operation of this equipment, be sure to read and
understand all cautions and warnings.
Hazard Statement Definitions
This manual may contain four types of hazard statements:
DANGER
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Safety instructions
Following are general caution and warning statements that
apply to this equipment. Additional statements, related
to specific tasks and procedures, are located throughout
the manual.
DANGER
Hazardous voltage. Contact with high voltage will
cause death or severe personal injury. Follow all locally
approved safety procedures when working around
high- and low-voltage lines and equipment.
WARNING
Before installing, operating, maintaining, or testing this
equipment, carefully read and understand the contents
of this manual. Improper operation, handling or
maintenance can result in death, severe personal injury,
and equipment damage.
WARNING
This equipment is not intended to protect human
life. Follow all locally approved procedures and safety
practices when installing or operating this equipment.
Failure to comply may result in death, severe personal
injury and equipment damage.
WARNING
Indicates a hazardous situation which, if not avoided,
could result In death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
CAUTION
Indicates a hazardous situation which, if not avoided,
could result in equipment damage only.
WARNING
Power distribution and transmission equipment must
be properly selected for the intended application. It
must be installed and serviced by competent personnel
who have been trained and understand proper safety
procedures. These instructions are written for such
personnel and are not a substitute for adequate training
and experience in safety procedures. Failure to properly
select, install or maintain power distribution and
transmission equipment can result in death, severe
personal injury, and equipment damage.
INSTALLATION INSTRUCTIONS MN650053EN May 2017
iii
600 A 15 kV, 25 kV and 35 kV class bushing extender installation instructions
WARNING
Visible break and adequate grounding must be
provided before cable work proceeds. All associated
apparatus must be de-energized during installation and
maintenance. Failure to comply may result in death,
severe personal injury and equipment damage.
Product information
The twin 600 A interfaces of the bushing extender allow
installation on standard de-energized 600 A deadbreak
interfaces for coupling reducing tap plugs, connecting
plugs and apparatus bushings. When assembled to mating
apparatus, it provides a completely submersible, fully shielded
unit that meets the requirements of IEEE Std 386™ standard.
Installation procedure
Bushing extender kit
●●
Bushing Extender
●●
Silicone Lubricant
●●
Installation Instruction Sheet
Installation instructions
Step 1
Clean and lubricate
●●
Read this manual first
●●
Read and understand the contents of this manual and follow
all locally approved procedures and safety practices before
installing or operating this equipment.
●●
Additional information
These instructions cannot cover all details or variations
in the equipment, procedures, or process described nor
provide directions for meeting every possible contingency
during installation, operation, or maintenance. For additional
information, contact your representative.
●●
Remove protective cap from apparatus bushing and both
ends of bushing extender.
Clean and lubricate bushing extender interfaces with
the lubricant supplied.
Clean and lubricate apparatus bushing interface with
lubricant supplied.
Ensure that all mating surfaces are kept clean
during installation.
Step 2
Assemble
●●
●●
Push bushing extender onto apparatus bushing.
Install mating component per the instructions provided
with that component.
Step 3
Install drain wire
●●
Figure 1. 600 A bushing extender unit (35 kV shown)
Acceptance and initial inspection
Each bushing extender is in good condition when accepted
by the carrier for shipment. Upon receipt, inspect the
shipping container for signs of damage. Unpack the bushing
extender and inspect it thoroughly for damage incurred
during shipment. If damage is discovered, file a claim with
the carrier immediately.
Handling and storage
Be careful during handling and storage of the bushing
extender to minimize the possibility of damage. If the
bushing extender is to be stored for any length of time prior
to installation, provide a clean, dry storage area.
Standards
ISO 9001 Certified Quality Management System
1
INSTALLATION INSTRUCTIONS MN650053EN May 2017
Connect uninsulated copper drain wire from drain wire
tabs on bushing extender to system ground and to
mating component.
BUSHING EXTENDER
CLEAN AND LUBRICATE
DRAIN WIRE
TO SYSTEM
GROUND
DRAIN WIRE
TO MATING
COMPONENT
DRAIN WIRE
TAB OF MATING
COMPONENT
DRAIN WIRE TAB
Figure 1. Line illustration of bushing extender installation
600 A 15 kV, 25 kV and 35 kV class bushing extender installation instructions
This page intentionally left blank.
INSTALLATION INSTRUCTIONS MN650053EN May 2017
2
600 A 15 kV, 25 kV and 35 kV class bushing extender installation instructions
This page intentionally left blank.
3
INSTALLATION INSTRUCTIONS MN650053EN May 2017
!
SAFETY
FOR LIFE
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
© 2017 Eaton
All Rights Reserved
Printed in USA
Publication No. MN650053EN
May 2017
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
For Eaton’s Cooper Power series product
information
call 1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising