AC2316说明书
 —
Wie Fl (Ere о @JCG
REPEATER Wi-Fi Range Extender Linkmy world
Model No: JWA-AC2316R
|. Parts of the Wifi Repeater
—
PAA
o 10 6
\ > /
(4
1. POWER LED 7. RESET Button
2. WAN/LAN LED 8. WPS Button
3. LAN LED 9. Mode Switch(Repeater mode,Router
4. 2.4G Signal LED
5. 5G Signal LED
6. POWER ON/OFF Switch
mode, AP mode)
10. WiFi Signal Strength Indicator
11. LAN Port
12. WAN/LAN Port
Il. LED Indicators
LED Status Meaning
2.4G Signal/5G LED off No wifi signal
Signal LED flashing Transferring data
LED off Power off
POWER
LED on Power on
Weak reception, strength
One LED on
below 25 %
WiFi Signal Good reception, strength
Two LEDs on
Strength Indicator 50%~75%
Th LED Excellent reception,
ree son strength above 75%
LED on Cable connection ok
LAN& LAN/WAN
LED off Cable connection not ok
lll. Configuration of the Wifi Repeater
The repeater has founctions: repeater, router and Access Point. We describe
the setup as wifi repeater in details. So firstly make sure the mode switch is in
the repeater mode.
There are two ways to set up this device as wifi repeater, with WPS or without
WPS. If you want to setup with WPS button, please make sure that the other
device(that you want to conect with) has also a WPS button.
1. Connect the wifi repeater to your exsiting router by WPS button.(go to
point 2 if your exsiting router does not have WPS)
a. Plug the Wifi repeater into a power outlet near your exsiting router (not too
far away from your router) and wait for the repeater to start up.
b. Press WPS button on your exsiting router (usually press the WPS button
for 3 seconds, consult the manual of your exsiting router).
c. Activate WPS on the Wifi repeater by pressing the WPS button for over 5
seconds.
d. The Wifi repeater will connect to your exsiting router. This will take some
time, please wait at least 2 minutes.
2. Connect the Wifi repeater to your exsiting router without WPS.
a. Plug the Wifi repeater into a power outlet near your exsiting router (not too
far away from your router) and wait for the repeater to start up.
b. The Wifi repeater will need to know to which Wifi network it should be
connected and what the password is. Therefore, it is necessary to set the Wifi.
You will need a network cable. Plug one side of the cable in the Wifi
repeater(LAN port) and plug the other end in your PC. You may need to
temporarily disconnect the existing Internet cable.
c. Enter 192.168.10.1 in your web browser (do not use Google, enter it in the
URL bar).
d. Enter admin in both the name and password field.
e. The following screen will appear. Click on “Repeater Wizard”.
Click on Repeater Wizard
2 4G Wifi Clients: 1
Repeater Mode
ее ох
User This Device AP/Router Internet
Internet
4 irda 6R-2.4G Repeater SSID
No
JWA-AC2316R-5G LAN Settings
48 IP Address
No Subnet Mask
remoteap1
Repeater Signal 0%
192:168.10.1
255.205.2050
Running Time
0 Days 0 Hours 10 Mins 6 Secs
Password Settings
Save/Import Settings
Firmware Version
Upgrade Firmware 113.10.1.179
Router MAC Address:
00:E0:4C:23:19:172
Restart Device
Log out
f. All available Wifi networks will be shown in a screen like the one shown
here.
WI-FI Range Extender
E
WIFI TEST DEVICE 11 WPA2-PSK „||
PHICOMM_70 7 WPA-PSKWPA2-P5k ill
UNKNOW 11 WPA-PSK/WPA2-PSK alll
JCG-M007-fangke 6 Disabled ul
JCG-M007-2.4G-ext 6 \WPAZ-PSK all |
360EWIFHIT 9 WPA2-PSK il -
ace = VIA MEZ «E
onnect ta remoteapz
JWA-AC2316R-2.4G
JWA-AC2316R-5G
O
g. Select your network by clicking on the circle in the column “Choose” and
enter your password details.
h. Click the “Save” button (at the bottom). The settings are now being saved,
that is why the repeater will ask you to wait for 90 seconds. Afterwards you
can remove the internet cable, and install the Wifi repeater at the selected
location.
WPA2-PSK
6
GR-N102-2.4G 1 WPA-PSKMWPAZ-PSK
JCG—fangiang 9 WPA2-PSK
JCG-8018 2 WPA-PSKAWPA2-PSK
HERE 2 WPA-PSKWPA2-PSK — nll
Xiaomi_2001 7 WPA-PSKWPA2-PSK „и
HERE 13 Disabled lil
ipcljfiegbpwj6qq 6 Disabled ill | У
JCG--fangian
Motice: The Repeater Wireless Key will be the same as your Wireless AP/Router after
settings.
5G SSID JCG-fangiang-5G-ext
JCG-fangiang-ext
Restart Device
00:E0:4C:23:19:12
Log out
3. Connect your laptop, mobile phone or tablet to the Wifi repeater
a. You can now insert the Wifi repeater in the selected power outlet. Once
again, this will take some time. Wait at least 2 minutes after insertion.
b. Search for new Wifi connections from your mobile device, e.g. laptop,
phone or tablet. Select the SSID with -ext at the end(for example, if your
exsiting router has SSID ABC, select ABC-ext or ABC-5G-ext ). The 56Hz
connection is quicker and will automatically select wifi-AC if this is available
on both devices.
c. The password will be the same as your existing router.
4. Connect an end device to the Wifi repeater using WPS
a. End devices are e.g. PC, mobile phone, tablet or IP camera. Activate WPS
on the end device according to the manual of the device.
b. Press the WPS button on the Wifi repeater for less than 3 seconds.
c. The devices will now connect. After about 2 minutes, the connection works.
IV. Frequently Asked Questions (FAQ):
Q1: What should | do if my router does not have a WPS button?
A: Please follow instructions on option two - to set up using the browser.
Q2: How to Reset to defaults?
A: While the power is still on, keep pressing the reset button on the right side
of the product for 5 to 10 seconds, and it will restore to factory settings.
Q3: Why cannot | see the login page after entering http://192.168.10.1 in the
browser?
A: Make sure your PC or phone is connected to the extender network and has
disconnected from any other network. Also please make sure your PC or
phone is set to obtain an IP address automatically.
Q4: My signal from the range extender is weak, and keeps dropping off.
A: Please place the extender in a proper location, i.e. where a minimum of 3
router signal strength bar is shown (please check the signal strength of that
specific location with your phone or PC)
YICHEN (SHENZHEN) TECHNOLOGY CO.,LTD.
Add: 23 F, Building C1, Nanshan Zhiyuan, No. 1001 Xueyuan Road, Xili, Nanshan District,
Shenzhen City, Guangdong, China
website: www.jcgcom.com
Contact Information
[Distribution Enquiry] [OEM Enquiry] [Technical Support]
Email: marketing@jcg.com.cn
TEL: +86-755-86664000
Contacts: Michael Zhu
Email: Zcq@jcg.com.cn
TEL: +86-755-86238512
SKYPE: zeq_8michael
Email: support@jcg.com.cn
210*285mm 80g# tx K 4 EN ¡mi
EAN —X ERAN mm >] 105*9 5 т
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising