Upgrade Kit User`s Manual
SD-860/866/870/876 Series
Upgrade Kit
User’s Manual
Rev.: A0
I.
FEATURES
Upgrade kit for KS series (SD-860/866) and Jiva series (SD-870/876)
Magnetic Stripe Reader in USB full speed HID interface
Options for MSR heads covering ISO single head & dual head or JIS I/II
3 tracks type MSR can read also AAMVA and CA DMV card
Build-in RFID Reader with HID class (RF-300) in USB interface.
Customization Options:
▪ MSR, Wi-Fi and RF300
▪ RF300
▪ MSR, RF300
▪ MSR and Wi-Fi.
▪ MSR.
▪ MSR and RFID/RFID-HID
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause
interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians. The user should consult his/her
dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by no
means responsible for any damage or hazard caused by improper application.
The hardware utility program, including instructions for its use, is provided “AS IS” without warranty of any kind. Posiflex Technology, Inc. further disclaims
all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose. the entire risk arising out of
the use or performance of the software and documentation remains with you.
ABOUT THIS MANUAL
This manual is written in an attempt with full strength to assist the user to utilize the upgrade kit SD-860/866/870/876 for the Posiflex fan free touch terminals
KS & TP series systems. This series of products incorporate 2 delicately designed POS peripherals each can be used as an excellent tool to accommodate the
required security specially involved in POS business, kiosk and hospitality operation. This manual covers the conceptual and operational aspects of these units.
For technical aspects involving opening of the unit or option implementation, it is only available to the authorized distributors.
The manufacturer of the SD-860/866/870/876 series heartily apologizes to the user for reserving the right to change or to modify this manual without notice
due to the rapid and constant progress and improvement on science and technology. The user may always obtain the most up to date information through any
of our web sites: http://www.posiflex.com or http://www.posiflex.com.tw.
 Copyright Posiflex Technology Inc. 2013
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, or otherwise, without the prior written consent of Posiflex Technology, Inc. the publisher of this documentation
TRADE MARKS AND SERVICE MARKS
P/N: 19860901020
POSIFLEX is a registered trademark of Posiflex Technology, Inc. an ISO-9001 and ISO-14001 certified manufacturer.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
II.
警告使用者
Installing SD-860/SD-866 on KS series
1.
2.
3.
T31454
這是甲類的資訊產品,在居住的環
境中使用時,可能會造成射頻干
擾,在這種情況下,使用者會被要
求採取某些適當的對策。
INSTALLATION
Remove the expansion bay cover on the rear left side of the KS terminal by releasing the
two screws
Connect the cable inside the expansion bay to the white
connecter inside SD-860/SD-866.
Ensure the screw holes on both SD-860/SD-866 and the
terminal are in alignment, and secure the screws.
Installing SD-870/SD-876 on TP series
1.
2.
3.
Assemble the two adapter plates in the package together.
Install the plate assembly onto the rear left side of a TP terminal.
Ensure the screw holes on both SD-870/SD-876 and the terminal are in alignment, and
secure the screws. Connect the USB connector with the USB port of the terminal.
1.
2.
3.
Page 1
Installing RFID Only Model
1.
2.
3.
4.
Remove the two screws securing the bottom cover of the SD unit.
Remove the bottom cover from the SD unit. Remove the expansion bay cover on the rear
left side of the terminal by releasing the two screws
Connect the cable inside the expansion bay to the white connecter on RFID board inside
the SD unit.
Ensure the screw holes on both SD unit and the terminal are in alignment, and secure the
two screws. Put back the expansion cover back and secure the two screws.
1.
2.
3.
4.
Installing Wi-Fi module to SD-860/866/870/876
1.
2.
3.
4.
1.
Remove the two screws securing the bottom cover of the SD unit.
Remove the bottom cover from the SD unit.
Insert the USB Wi-Fi module into the internal USB port.
Put the bottom cover back and fasten the screw as shown in the picture.
2.
3.
4.
DRIVER INSTALLATION
MSR
▪ Additional driver is unnecessary for connection through USB under Windows.
▪ To enable MSR under MS-DOS, enable the USB keyboard and set USB operation mode to
Full/Low Speed in system CMOS setup.
RFID Reader
▪ RFID can work under both DOS and Windows.
III. OPERATION GUIDE
MAGNETIC STRIPE READER
For magnetic stripe card reading, be sure to insert the card to the bottom with magnetic stripe
facing the mark aside the slot. The movement of the card can be either inserting the card from
the top to down out or sliding the card upward from the lower side to the top end as long as the
card is a standard one.
The MSR in SD-860/866/870/876 reads an ISO or JIS magnetic stripe card without driver. Yet,
there is a “Posiflex USB MSR Manager” program provided to control some parameter
configuration for ISO MSR. The features controllable in this program cover: each track
enable/disable, Alt+Num approach for ASCII codes and Leading/Stop code enable/disable.
The function for enabling each track of course comes in effect only when the track is
physically available. Please find in the Product Information CD or DVD delivered with KS
system the folder “\Drivers\SD_Series\USBMSR_xxx” and “SetUp” this manager program or
download the installation program from our web http://www.posiflex.com or
http://www.posiflex.com.tw.
RFID Reader – RF-300
The RFID reader is a radio-enabled device that communicates with a tag and with
the host system. In order to communicate with each other, the reader and the tag
must be set at same frequency and the tag must be within the reader’s RF range as
circled in the right picture. Various tags are available for use in different
applications and environments as well as can add data to the tag or the existing tag
data can modify. RDID reader – RF300 can be featured as follows:
1.
An enabled USB keyboard output interface for easy access
2.
Shipped with a RFID test card for customized recording, P/N: 21898410101
3.
Mi fare 13.56 MHZ standard
4.
RF-300 can only work with POSIFLEX CC-1200 for data encode
Page 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising