QUICK OPERATION GUIDE ia14

QUICK OPERATION GUIDE ia14
•
Side Tone Function (for A14 only)
When using a third-party headset, the transceiver outputs your transmitted voice to the headset for monitoring, and a headset adapter is required
Connect the optional headset with the transceiver via the
OPC-499 headset adapter
– Illustration shows where the headset adapter jack
insertes
into the radio
Jack cover
FREQUENCIES/CHANNELS NOTES
EMERGENCY
Push func (found at the bottom right of the keypad) then [0 121.5] (found next to the func
func key). Use the PTT to call on the emergency frequency
NOTE: Attach the jack
cover when the optional
equipment is not used.
•
SETTING THE SIDE TONE LEVEL [PTT]
Push [PTT] (see drawing) to turn the transmit mode ON
During transmit, push [Y ]or
[Z]/[Y]
[ Z] to adjust the level
–‘ST--0’ is OFF and ‘ST-10’ is the maximum level
– Illustration shows side tone level indication
QUICK OPERATION GUIDE
ia14
GENERAL
If the key marking on the keypad is in black, push to func activate. For secondary functions, first push func
and then the desired green-marked key
1
3
KNOB (1)
Rotate to turn the radio power on or off
and to adjust the audio level
SIDE KEYS (2)
Side tone level is indicated
©2008 Icom America Inc. The Icom logo is a registered trademark of Icom Inc.40084
2
• SET SQUELCH
Push [SQLY] or [SQLZ] (2) to the point where noise is just muted. Push [CLR] to return to frequency mode
• WEATHER (WX), ON or OFF
func then push [4 WX-ALT] to Push func
turn weather alert ON or OFF
– If you are experiencing an interruption every 5 seconds, turn your weather alert OFF, the “WX” symbol will disappear from the screen
• LOCK, ON or OFF (3)
Push the KEY LOCK switch [key1] to turn ON
Push and hold switch 2 seconds to turn OFF
• SCAN, ON or OFF
func then push [2 SCAN]
Push func
Push [Y ] or [ Z] to change the scan direction To stop scan, push [CLR]. To resume, push [CLR] func [2 SCAN]
• MEMORY SCAN
Push [MR MW] to enter memory mode
func, then push [2 SCAN]
Push func
–To stop scanning, push [CLR]
• CLEAR ALL
Push [CLR] twice
•
•
•
•
PROGRAM FREQUENCIES INTO MEMORY
SELECT THE DESIRED FREQUENCY
Push [CLR], then select the desired frequency by using
the keypad.
Push func
func then push [MR MW]
– A large “M“ will blink at the top on screen
Push [Y ] or [ Z] to select the channel
Push [ENT SET] to save
ENTER BANK SELECTION MODE & SELECT A BANK
Push func
func then push [3 BANK]
Push [Y ] or [ Z] to select the bank
Push [ENT SET] to save
Finish Writing To Memory
Now that the channel and bank have been selected, push [ENT SET] to save and end.
FIND FREQUENCY IN MEMORY
Push [MR MW] and push [Y ] or [ Z] to scroll through the memory channels, pause at each channel and the frequency will momentarily appear
•
•
TAG (SELECT SCAN) CHANNELS
TAG channels is Icom’s way of selecting and deselecting channels to be scanned
TO TAG A MEMORY CHANNEL
Push [CLR] then select the desired frequency by using
the keypad
Push [MR MW] to select the memory mode, if desired, then select the BANK.
Push func then push [3 BANK]
Push [Y ] or [ Z] to select the bank
Push func then push [9 TAG] the TAG symbol
appears, and to cancel the TAG setting, repeat above steps
– A TAG symbol will appear when TAG is ON
– The TAG function is only available for scan operation
HOW TO DELETE CHANNELS IN MEMORY
Push [MR MW] to select memory mode
Select the desired channel to delete
Push func , then push and hold [CLR HOME] for
1 second
– The screen will read: 
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising