Intova IC14 user manual

Intova IC14 user manual
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
„ Reorient or relocate the receiving antenna.
„ Increase the separation between the equipment and receiver.
„ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
„ Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15
of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise
specified in the manual. If such changes or modifications should be made, you could
be required to stop operation of the equipment.
Notice
If static electricity or electromagnetism causes data transfer to discontinue midway
(fail), restart the application or disconnect and connect the communication cable
(USB, etc.) again.
EN-1
READ THIS FIRST
Trademark Information
„
„
„
„
„
„
Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.
Pentium® is a registered trademark of Intel Corporation.
Macintosh is a trademark of Apple Inc.
SD™ is a trademark.
SDHC™ is a trademark.
Other names and products may be trademarks or registered trademarks of their
respective owners.
Product Information
„ Product design and specifications are subject to change without notice. This
includes primary product specifications, software, software drivers, and user’s
manual. This User Manual is a general reference guide for the product.
„ The product and accessories that come with your camera may be different from
those described in this manual. This is due to the fact that different retailers often
specify slightly different product inclusions and accessories to suit their market
requirements, customer demographics, and geographical preferences. Products
very often vary between retailers especially with accessories such as batteries,
chargers, USB-AC adapters, memory cards, cables, pouches, and language
support. Occasionally a retailer will specify a unique product color, appearance,
and internal memory capacity. Contact your dealer for precise product definition
and included accessories.
„ The illustrations in this manual are for the purpose of explanation and may differ
from the actual design of your camera.
„ The manufacturer assumes no liability for any errors or discrepancies in this user
manual.
EN-2
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the camera, turn the power off
and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
If the camera has fallen or its case has been damaged, turn the power
off and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask
the store of purchase.
Use the supplied USB-AC adapter only with the indicated power
supply voltage.
Use with any other power supply voltage might cause fire or electric shock.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow,
on the beach, or near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing damage.
Keep the battery out of the reach of children.
Swallowing the battery might cause poisoning. If the battery is accidentally
swallowed, immediately consult a physician.
Do not use the camera while you are walking, driving or riding a
motorcycle.
This might cause you to fall over or result in traffic accident.
Please use battery with complete external seals.
Do not use battery from which the seals have been damaged or removed.
This may cause leakage, explosion, or injury.
EN-3
Cautions
Insert the battery paying careful attention to the polarity (+ or –) of the
terminals.
Inserting the battery with its polarities inverted might cause fire and injury, or
damage to the surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to
leak. If the internal fluid enters your eyes or comes into contact with your
body or clothes, rinse with fresh water. If the internal fluid has entered your
eyes, consult a physician to receive treatment.
A camera is a precision instrument. Do not drop it, strike it or use
excessive force when handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous
use.
The battery becomes hot during use. Touching a hot battery might cause
burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use
the camera in a well-ventilated place.
Do not leave the camera in places where the temperature may rise
significantly, such as inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and
electric shock.
EN-4
Notes on Battery Usage
When you use the battery, carefully read and strictly observe the Safety Instructions
and the notes descr bed below:
„ Use only the specified battery (3.7V).
„ Avoid extremely cold environments as low temperatures can shorten the battery
life and reduce camera performance.
„ When you are using a new rechargeable battery or a rechargeable battery that has
not been used for an extended period of time (the battery that passed the expiry
date is an exception), it may affect the number of images that can be captured.
Therefore, to maximize its performance and lifetime, we recommend that you fully
charge the battery and discharge it for at least one complete cycle before use.
„ The battery may feel warm after a long period of continuous use of the camera or
the flash. This is normal and not a malfunction.
„ The camera may feel warm after a long period of continuous use. This is normal
and not a malfunction.
„ If the battery is not to be used for a long period of time, remove it from the camera
to prevent leakage or corrosion and store it after no battery power is left. Stored for
a long time in a fully charged condition, its performance may be impaired.
„ Always keep the battery terminals clean.
„ There is a risk of explosion if the battery is replaced by an incorrect type.
„ Dispose of used battery according to the recycle instructions.
„ Charge the rechargeable battery fully before using for the first time.
„ To prevent short-circuiting or fire, keep the battery away from other metal objects
when carrying or storing.
This symbol mark [crossed-out wheeled bin] indicates separate
collection of waste batteries in the EU countries. The batteries
provided with this product shall not be treated as household
waste. Please use the return and collection systems available in
your country for the disposal of the waste batteries.
If a chemical symbol is printed beneath the symbol mark, this
chemical symbol means that the batteries contains a heavy
metal at a certain concentration. It is indicated as follows:
Hg: mercury, Cd: cadmium, Pb: lead.
EN-5
CONTENTS
7
INTRODUCTION
26 MENU OPTIONS
7
7
Overview
Package Contents
8
GETTING TO KNOW YOUR
CAMERA
26
29
30
32
8
8
9
Front View
Rear View
LCD Monitor Display
11 GETTING STARTED
11 Preparation
11 Charging the Battery
12 Initial Settings
14 CAPTURE MODE
14
14
15
17
17
18
18
18
19
19
Capturing Images
AF Tracking Mode
Setting the Scene Mode
Taking Images with Intelligent Scene
mode
Taking Images When the Smile
Feature Is On
Taking and Combining Panoramic
Pictures
Mode of Skin Soften and De-blemish
Find Blur Function
Recording Shots using Face
Detection Technology
Self-portrait Function
20 VIDEO MODE
20 Recording Video Clips
20 Playing Back Video Clips
21 PLAYBACK MODE
21
21
22
22
23
24
25
Playing Back Still Images
Playback Display
Removing Red-eye
Dynamic Lighting Feature
Attaching Voice Memos
Protecting Images
Erasing Images
EN-6
Capture Menu
Video Menu
Playback Menu
Setup Menu
34 TRANSFERRING FILES TO
YOUR COMPUTER
34 Downloading Your Files
34 USING THE CAMERA AS A PC
CAMERA
35 EDITING SOFTWARE
INSTALLATION
36 SPECIFICATIONS
37 APPENDIX
37 Possible Number of Shots
38 Troubleshooting
INTRODUCTION
Overview
Congratulations on your purchase of the new digital camera.
Capturing high-quality digital images is fast and easy with this state-of-the-art smart
camera. Equipped with a 14.0-megapixel CCD, this camera is capable of capturing
images with a resolution of up to 4288 x 3216 pixels.
Package Contents
Carefully unpack your camera and ensure that you have the following items:
Common Product Components:
„ Digital Camera
„ Instruction manual
„ Quick Start Guide
„ Software CD-ROM
„ Camera strap
„ Rechargeable lithium-ion battery
„ AV cabel
„ USB cable
„ USB-AC adapter
EN-7
GETTING TO KNOW YOUR CAMERA
Front View
1. Flash
2. Shutter button
3. ON/OFF Power button
4. Self-timer LED
5. Microphone
6. Lens
Rear View
A
1
A. LCD monitor
B
2
C
3
4
5
6
7
8
D
E
G
1.
2.
3.
4.
5.
6.
Function
Video Mode
Shutter button
Record button
: Zooms out
: Zooms in
Switches to:
Video mode > Capture
mode
Focus
Compensation s>P
Flash
7.
If any scene mode is set:
switches to scene mode
selection screen
8.
Self-timer
9.
Playback mode
EN-8
D. Strap holder
E. Battery / Memory card cover
G. Speaker
F
Capture Mode
10. Capture menu
C. USB and AV OUT terminal
F. Tripod socket
9
10
Item
B. Status LED
--
Playback Mode
Still image: to capture mode
Video clip: to capture mode
: Zooms out
: Zooms in
Switches to:
Capture mode > Video mode
Still image: to capture mode
Video clip: to capture mode
Focus
Next 10th image
Previous Image
Next Image
Still image: to display image
Records voice memo ( if
“Voice Memo” is “Record”).
Video clip: to play video clip
Previous 10th image
Still image: to capture mode
Video clip: to capture mode
Playback menu
---Self-timer
Playback mode
Video menu
LCD Monitor Display
Capture mode
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Zoom status
Available number of shots
Storage media
[r]
Internal memory (no card)
[
]
SD/SDHC memory card
Battery condition
[l]
Full battery power
[o]
Medium battery power
[n]
Low battery power
[m]
No battery power
Focus setting
[K]
Auto
[ ]
AF Tracking
[ ]
Face Detect
[ ]
Macro
[ ]
Super Macro
[Q]
Infinity
Flash mode
[b]
Auto
[a]
Flash On
[d]
Flash Off
[c]
Red-eye
[`]
Slow Sync
[_]
Pre-flash
[s]
Exposure compensation
( It can not be used in below modes: Tv, Av,
Intelligent Scene, Smile Detection, Skin Soften,
De-blemish, Portrait Man & Portrait Lady. )
[P]
Backlight correction
( It can only be used in Smile Detection, Skin
Soften, De-blemish, Portrait Man and Portrait Lady. )
Self-timer & Self-portrait icon
[i]
Off
[ ]
Self-portrait
[f]
2 sec.
[g]
10 sec.
[h]
10+2 sec.
[
]
Histogram
Image size resolution
[ ]
4288 x 3216
[ ]
3264 x 2448
[ ]
2304 x 1728
[ ]
1600 x 1200
[ ]
640 x 480
Set key: SCN hint icon
Main focus area
Date and time
Quick shot
Capture mode icon
[ ]
Single
[T]
Continuous
[U]
AEB (Auto Exposure Bracketing)
[-]
Album Shot
[/]
Burst
[.]
Cont.flash
[+]
Pre-shot
[,]
Coupl.shot
[ ]
Burst 30fps
White balance
[@]
Auto
[$]
Incand.
[&]
Fluoresc.1
Fluoresc.2
[*]
1
20
3
2
4
00214
19
5
18
6
17
7
16
8
15
9
14
13 15
2011 03 01 13:15
2011.03.01
17.
18.
19.
20.
SET
SCN
11
13
12
Daylight
[%]
[#]
Cloudy
[(]
Manual WB
Image quality
[
]
Fine
[
]
Standard
[
]
Economy
ISO
[ AUTO ]
Auto
[ 100 ]
ISO 100
[ 200 ]
ISO 200
[ 400 ]
ISO 400
[ 800 ]
ISO 800
[ 1600 ]
ISO 1600
[ 3200 ]
ISO 3200
Slow shutter warning
Mode icon / Scene mode
[
]
Program AE
[
]
Auto
[
]
Tv
[
]
Av
[
]
Intelligent Scene
[
]
Smile Detection
[
]
Anti-shake
[
]
Panorama PanCapture
[
]
Skin Soften
[
]
De-blemish
[
]
Portrait Man
[
]
Portrait Lady
[
]
Landscape
[
]
Sports
[
]
Night Portrait
[
]
Night Scene
[
]
Candlelight
[
]
Fireworks
[
]
Text
[
]
Sunset
[
]
Sunrise
[
]
Splash Water
[
]
Flow Water
[
]
Snow
[
]
Beach
[
]
Pets
[
]
Natural Green
10
EN-9
Video mode
1. Zoom status
2. Storage media
3. Battery condition
4. Focus setting
5. Flash off
6. Self-timer icon
7. Video resolution
8. Elapsed time / Available recording time
9. Main focus area
10. Date and time
11. Video quality
12. Audio off
13. Mode icon
1
12
4
5
6
7
2011 03 01
2011.03.01
9
10
1
EN-10
8
2
3
4
5
110 0201
14
13
12
11
10
F2.8
F2
8
1/3
9
6
13 15
2011 03 01 13:15
2011.03.01
SET
8
7
Playback mode - Video playback
1. Protect icon
2. Folder / File number
3. Storage media
4. Battery condition
5. Volume mode
6. Total recorded time
7. Video status bar
8. Video condition icon
9. Elapsed time
10. Set key: Play / Pause hint icon
11. Down key: Stop hint icon
12. Mode icon
3
11
Playback mode - Still image playback
1. Voice memo
2. Protect icon
3. Folder / File number
4. Storage media
5. Battery condition
6. Image size resolution
7. Set key: Play hint icon
8. Date and time
9. Histogram
10. Aperture value / Shutter speed
11. Exposure value
12. Image quality
13. ISO
14. Mode icon
2
13
1
2
3
4
110 0201
110-0201
12
11
10
SET
00:00:00
9
00:24:59
8
7
6
5
GETTING STARTED
Preparation
1.
2.
3.
4.
Attach the camera strap.
Open he battery/memory card cover.
Insert the supplied battery wi h correct orientation as shown (label side front).
Insert an SD/SDHC memory card (Optional).
„ The camera has 32MB internal memory(23MB available for image storage), but you
can load an SD/SDHC memory card to expand the camera’s memory capacity.
„ Be sure to format the memory card with this camera before its initial usage.
5. Close the battery/memory card cover and make sure it is locked securely.
„
„
„
To prevent valuable data from being accidentally erased from an
SD/SDHC memory card, you can slide the write protect tab (on
the side of the SD/SDHC memory card) to “LOCK”.
To save, edit, or erase data on an SD/SDHC memory card, you
must unlock the card.
To prevent damaging of an SD/SDHC memory card, be sure to
turn off the power when inserting or removing the SD/SDHC
memory card. If inserting or removing the SD/SDHC memory card with the power on, the camera will
automatically turn off.
Charging the Battery
The battery is not fully charged at he time of purchase. Fully charge the battery and discharge
it for at least one complete cycle before use to maximize its performance and lifetime.
1. Connect camera to USB-AC adapter with USB cable.
2. Insert the plug into a wall outlet.
„
„
„
Status LED
Description
Green (blinks slowly)
Charging normally
Off
Charging finished
Green (blinks quickly)
Error
2
1
The included USB-AC adapter differs depending on the region where you purchased the camera.
User can also charge the battery by connecting camera to computer with USB cable.
Charging time varies according to the ambient temperature and the status of battery.
EN-11
Initial Settings
The language & date/time needs to be set if and when:
„ The camera is turned on for the first time.
„ The camera is turned on after leaving the camera without the battery for an
extended period of time.
1. Press the ON/OFF button to turn the power on.
2. Press any button to enter language setup. Select the displayed language with the e
/ f / c / d buttons and press the SET button.
3. Select the date format with the c / d buttons, and press the SET button.
4. Select the item’s field with the e / f buttons and adjust the value for the date and
time with the c / d buttons.
5. After confirming all settings are correct, press the SET button.
„ Half press the shutter button or press the MENU button will enter capture mode
without saving the settings.
Setting the Date and Time
When the date and time information is not displayed on the LCD monitor, follow these
steps to set the correct date and time.
1. Press the MODE button, and set the camera
mode to [
] or [ ]; or press the 7 button.
2. Press the MENU button.
3. Select the [Setup] at the end of the Menu with the
c / d buttons, and press the SET button.
4. Select [Date/Time] with the c / d buttons, and
press the SET button.
5. Select the date format with the c / d buttons, and
MENU ;
SET ;
press the SET button.
„ Select the item’s field with the e / f buttons
and adjust the value for the date and time with
the c / d buttons.
„ The time is displayed in 24-hour format.
„ After confirming all settings are correct, press
the SET button.
6. To exit from the [Setup] menu, press the MENU
button.
;
;
MENU
EN-12
SET
Choosing the Language
Specify in which language menus and messages are to be displayed on the LCD
monitor.
1. Press the MODE button, and set the camera mode
to [
] or [ ]; or press the 7 button.
2. Press the MENU button.
3. Select the [Setup] at the end of the Menu with the
c / d buttons, and press the SET button.
4. Select [Language] with the c / d buttons and
press the SET button.
5. Select the displayed language with the e / f / c /
MENU ;
SET ;
d buttons and press the SET button.
„ The setting will be stored.
6. To exit from the [Setup] menu, press the MENU button.
Formatting the Memory Card or Internal Memory
This utility formats the memory card (or internal memory) and erases all stored images
and data.
1. Press the MODE button, and set the camera
mode to [
] or [ ]; or press the 7 button.
2. Press the MENU button.
3. Select the [Setup] at the end of the Menu with the
c / d buttons, and press the SET button.
4. Select [Format] with the c / d buttons, then
press the SET button.
5. Select [Execute] with the e / f buttons, and
MENU ;
SET ;
press the SET button.
„ To cancel formatting, select [Cance ] and
press the SET button.
6. To exit from the [Setup] menu, press the MENU
button.
MENU ;
SET
;
EN-13
CAPTURE MODE
Capturing Images
Your camera is equipped with a 2.7” full color TFT LCD monitor to help you compose
images, playback recorded images/video clips or adjust menu settings.
1. Press the ON/OFF button to turn the power on.
2. Press the MODE button, and set the camera mode to [
].
3. Compose your image in the LCD monitor.
„ Pressing the
button zooms in on the subject, and enlarges the subject on the
LCD monitor.
„ Pressing the
button zooms out on the subject, and provides a wider angle
image.
4. Press the shutter button.
„ Pressing the shutter button down halfway
automatically focuses and adjusts the exposure,
and pressing the shutter button down fully
captures the image.
„ The focus area frame turns green when the
camera is in focus and the exposure is
calculated.
„ When the focus is not suitable, the frame of the
focus area turns red.
AF Tracking Mode
Use this option to take pictures of moving subject.
1. Press the MODE button, and set the camera mode to [
].
2. Press the
button, and select [ ] icon with the e / f buttons. Press the SET
button.
3. To lock the desired tracking subject, press the d button.
„ The frame automatically tracks the subject movement to focus on it continuously.
4. Press the shutter button down fully to capture your image.
„ When the camera fails to recognize or track the subject, the frame will turns red
and blinks. After blinking of the red frame, the camera returns to unlock display.
„ Press the d button, to returns to unlock display.
EN-14
Setting the Scene Mode
By simply selecting one of the available scene modes, you can capture the image with
the most appropriate settings.
1. Press the MODE button, and set the camera mode to [
], and press the SET
button.
2. Select the desired scene mode with the e / f / c
/ d buttons, and press the SET button.
3. Compose the image and press the shutter button.
;
;
The table below will help you choose the appropriate scene mode:
Scene mode
Description
Program AE
Select this mode when you want to set parameters manually
other than the shutter speed and the aperture value.
Auto
Select this mode when you want to capture images without
having to set special functions or manual adjustments.
Tv
Select this mode when you want to capture fast moving subjects
in fast shutter speed, or capture still subjects in slow shutter
speed.
Av
Select this mode when you want to capture images with the
priority given to aperture.
Intelligent
Scene
Select this mode when you want the camera to select an ideal
shooting mode according to environment automatically.
Smile Detection
Select this mode to automatically capture an image when a
smiling face is detected.
Anti-shake
Select this mode when you want to minimize the influences of
hand shaking when capturing an image.
Panorama
PanCapture
Select this mode when you want the camera to combine pictures
in the camera automatically.
Skin Soften
Select this mode when you want the camera to reduce artifacts
on faces.
De-blemish
Select this mode when you want the camera to reduce obvious
blemishes and big spots on faces.
EN-15
Scene mode
Description
Portrait Man
Select this mode when you want to capture an image that
makes a man stand out against a blurred background.
Portrait Lady
Select this mode when you want to capture an image that
makes a lady stand out against a blurred background.
Landscape
Select this mode when you want to capture an image with
infinity focus, hard sharpness and high saturation.
Sports
Select this mode when you want to capture fast-moving
subjects.
Night Portrait
Select this mode when you want to capture people with an
evening or night scene background.
Night Scene
Select this mode when you want to capture dark scenes such as
night views.
Candlelight
Select this mode when you want to capture photos of candlelight
scene, without spoiling the ambience.
Fireworks
Select this mode when you want to capture fireworks clearly with
optimal exposure. The shutter speed becomes slower, so using
a tripod is recommended.
Text
Select this mode when you want to capture an image that
contains black and white subjects like printed documents.
Sunset
Select this mode when you want to capture a sunset. This mode
helps keep the deep hues in the scene.
Sunrise
Select this mode when you want to capture a sunrise. This
mode helps keep the deep hues in the scene.
Splash Water
Select this mode when you want to capture photos of splashing
water.
Flow Water
Select this mode when you want to capture the soft flowing
water.
Snow
Select this mode when you want to capture clear snow scenes
without darkened subjects and bluish tint.
Beach
Select this mode when you want to capture bright beach scenes
and sunlit water surfaces.
Pets
Select this mode when you want to capture your pets. Shoot
from their eye level.
Natural Green
Select this mode when you want to capture the green scenery
background such as forest. This mode helps to brighten the
colors.
EN-16
Taking Images with Intelligent Scene mode
In this Intelligent Scene mode, the camera can sense the ambient conditions and
automatically select the ideal shooting mode.
1. Press the MODE button, and set the camera mode to [
], and press the SET
button.
2. Select [Intelligent Scene] with the e / f / c / d buttons, and press the SET button.
„ The camera can automatically select best mode for the shooting scene from
[Auto] / [Landscape] / [Backlight] / [Portrait] / [Night] / [Night Portrait] / [Macro].
3. Compose the image, and press the shutter button down fully.
Taking Images When the Smile Feature Is On
With the camera’s new “smile detection” function, this camera detects smiles so you
do not miss those special moments in life.
1. Press the MODE button, and set the camera mode to [
], and press the SET
button.
2. Select [Smile Detection] with the e / f / c / d buttons, and press the SET button.
3. Compose the image, and press the shutter
00214
button down fully.
4. Once the camera detects a smile, it will
automatically capture 3 images (by default, the
flash mode setting is set to d).
„ If the [Capture Md.] is set to [Single], the
camera will only capture an image after it
Smile Detection ON
detects a smile.
„ When capturing group shots (if the number of
people is more than 1), the camera will
automatically capture the image(s) when it
detects two smiles.
„ If the camera does not detect a smile within 5
seconds, the camera returns to preview
display.
„ Press the shutter button once again to
reactivate this function.
EN-17
Taking and Combining Panoramic Pictures
Pictures are manually shot, and the camera automatically combines pictures in the
camera.
1. Press the MODE button, and set the camera mode to [
], and press the SET
button.
2. Select [Panorama PanCapture] with the e / f / c / d buttons, and press the SET
button.
3. Select the photographic direction with the e / f buttons.
4. Shoot the first image.
„ The next image appears beside the previous image.
5. Orient the camera so that the second frame overlaps a small portion of the
photographic subject of the first image and press the shutter button to capture the
next image.
6. Follow the same steps to capture subsequent images in the sequence.
7. After the third picture is taken, the pictures are automatically combined.
Mode of Skin Soften and De-blemish
In order to make face taken look better and younger, mode of Skin Soften is added to
reduce artifacts on faces, while mode of De-blemish is to reduce obvious blemishes and
big spots on faces.
1. Press the MODE button, and set the camera mode to [
], and press the SET
button.
2. Select [Skin Soften] or [De-blemish] with the e / f / c / d buttons, and press the
SET button.
3. Compose the image, and press the shutter button down fully.
Find Blur Function
With the camera’s new “Find Blur” function, this camera finds the blurry photo when
capture under Continuous.
1. Press the MODE button, and set the camera
mode to [
].
2. Press the MENU button, and select [Find Blur]
icon with the c / d buttons. Set “Find Blur” on.
3. Press the shutter button to return to preview
display.
4. Press the shutter button down fully to capture
your image.
;
5. Press the SET (Execute) button to save the best
image.
„ Press the MENU (Cancel) button to save all images.
EN-18
Recording Shots using Face Detection Technology
Face Detection Technology can identify and focus on the human faces in the image.
1. Press the MODE button, and set the camera mode to [
].
2. Press the
button, and select [ ] icon with the e / f buttons. Press the SET
button.
„ With Face Detection turned on, the camera identifies main face (white frame)
and subsidiary faces (gray frames).
„ If the camera cannot detect and track any faces, there will be no frame shown on
the screen.
3. Press the shutter button halfway down to lock the
Main Face(Green Frame)
focus.
„ When the main face is in focus, the white frame
simultaneously turns green. Otherwise, it turns
red.
4. Press the shutter button down fully to capture your
image.
Focus Lock
„ Subjects that are not suitable with this function:
a. A person is wearing glasses, sunglasses, or face is covered with hat or hair.
b. A person turns sideways.
Self-portrait Function
Use this function to take pictures of yourself or include yourself in pictures.
1. Press the MODE button, and set the camera mode to [
].
2. Press the e button, and select [ ] icon with the e / f buttons. Press the SET
button.
3. Press the shutter button.
4. If the camera detect and track any faces, after twice blinking of the self-timer LED,
one image will be captured.
„ Press the shutter button to exit.
„ If it does not detect any face within 30 seconds, the camera will automatically
capture an image and return to preview display.
„ Select [ ] to reactivate this function.
EN-19
VIDEO MODE
Recording Video Clips
This mode allows you to record video clips at a resolution of 320 x 240 / 640 x 480 / 720p
pixels.
1. Press the MODE button, and set the camera mode to [
].
2. Compose the image.
3. Press the shutter button.
„ The recording of the video clip will start.
„ Pressing the shutter button one more time will end the
recording of the video clip.
„ The recording time depends on the storage size and the
subject of the image to be recorded.
„ The zoom function cannot be used during video recording.
„ When recording a video clip, the flash and "10+2 sec." self-timer function cannot be used.
„ If the write speed of your SD/SDHC memory card is not fast enough for recording video clips in
the currently selected quality, the video recording will stop. In this case, select a video quality
lower than the current one.
Playing Back Video Clips
You can play back recorded video clips on the camera.You can also play back sound if
recorded with he video.
1. Press the 7 button.
„ The last image appears on the screen.
2. Select the desired video clip with the e / f buttons.
3. Press the SET button.
„ A press of the f / e buttons during playback allows fast forward play / fast reverse
play.
„ To stop video playback, press the d button.
This stops playback and returns to the start of he video clip.
„ To pause video playback, press the SET button.
This pauses video playback.
To cancel pause, press the SET button again.
„ Video clips cannot be displayed rotated or enlarged.
„ Windows Media player or QuickTime Player is recommended to play back the video clip on your
computer.
„ QuickTime Player is a free media player available at www.apple.com; and compatible with Mac
and Windows computers.
„ For more information about the operation of the media player, refer to its respective help
documentation.
„ When watching a movie on a computer, frames may drop, it may not play smoothing, and the
audio may stop suddenly depending on the computer's capabilities.
EN-20
PLAYBACK MODE
Playing Back Still Images
You can play back he still images on the LCD monitor.
1. Press the 7 button.
„ The last image appears on he screen.
2. The images can be displayed in forward or reverse
sequence with the e / f buttons.
„ To view the previous image, press the e button.
„ To view the next image, press the f button.
„ Pressing the
button enlarges the image.
„ To return to normal magnification, press the
button.
„ An [ ] icon is displayed with images which have an audio memo recorded.
Playback Display
This function allows you to search quickly for the image that you want and playback images on
the LCD monitor sequentially.
1. Press the 7 button.
„ The last image appears on he screen.
2. Press the c button to display the next 10th image.
„ If the 1st image taken is displayed, press the c
button to playback he 11th image taken. Press
the c button again to playback the 21th image
taken and so forth.
3. Press the d button to display the previous 10th
image.
4. Press and hold the e / f buttons to display the
previous or next images automatically in sequential
order.
„ Release the e / f buttons if you wish to stop the automatic playback.
„ If the total number of images is less than 10, press the d button jumps to the first image and
press the c button jumps to the last image.
EN-21
Removing Red-eye
You can use this function to remove the red-eye effect after an image is taken.
1. Press the 7 button.
„ The last image appears on the screen.
2. Select the image that you want to edit with the e
/ f buttons.
3. Press the MENU button.
4. Select [Fix Red Eyes] with the c / d buttons, and
press the SET button.
5. Select [Execute] with the e / f buttons, and
MENU ;
SET ;
press the SET button.
6. View the changes on the corrected image.
7. To save your corrected image, select [Confirm]
with the e / f buttons, and press the SET
button.
„ When this process ends, this replaces the
original image with the corrected image.
Dynamic Lighting Feature
MENU ;
;
SET
This feature compensates for the unfavorable lighting conditions by brightening
underexposed areas and balancing overexposed areas.
1. Press the 7 button.
„ The last image appears on the screen.
2. Select the image that you want to edit with the e
/ f buttons.
3. Press the MENU button.
4. Select [Dynam. Light.] with the c / d buttons,
and press the SET button.
5. Select [High] or [Low] with the e / f buttons,
and press the SET button.
6. View the changes on the corrected image.
7. To save your corrected image, select [Confirm]
with the e / f buttons, and press the SET button.
„ When this process ends, this replaces the
original image with the corrected image.
MENU ;
MENU ;
EN-22
SET
SET
;
;
Attaching Voice Memos
A maximum of 30 seconds of audio can be recorded as a memo for captured still
images. The voice memo can be recorded only once.
1. Press the 7 button.
„ The last image appears on the screen.
2. Select the image to which you want to attach the voice memo with the e / f
buttons.
3. Press the MENU button.
4. Select [Voice Memo] with the c / d buttons, and press the SET button.
5. Press the SET button.
„ [VOICE RECORDING] is displayed on the screen and recording starts.
6. To stop recording a voice memo as it is being recorded, press the SET button again.
„ [VOICE RECORD END] will be displayed momentarily and the recording will
end. An [ ] icon is displayed with images that have been recorded with a voice
memo.
„ RE-REC mode can only be used for the recorded and selected file, and it can record voice memo
repeatedly to replace the previous recordings.
Playing back voice memo
A press of the SET button displays
PLAYBACK] and plays back the voice memo.
[VOICE
110 0201
110-0201
SET
„ Voice memo is only available for still images.
EN-23
Protecting Images
Set the data to read-only to prevent images from being erased by mistake.
1. Press the 7 button.
„ The last image appears on the screen.
2. Select the image that you want to protect with the
e / f buttons.
3. Press the MENU button.
4. Select [Protect] with the c / d buttons, and press
the SET button.
5. Select [Single] or [Al ] with the e / f buttons, and
MENU ;
SET ;
press SET button.
6. Select [Set] with the e / f buttons, and press the
SET button.
„ Protection is applied to the image and the
camera returns to the playback mode.
„ The protect icon [ ] is displayed with protected
images.
When [Al ] has been selected, [ ] is displayed
MENU ;
SET ;
with all the images.
Canceling the Protection
To cancel protection for only one image, display the
image on which you want to remove the image
protection.
1. Press the 7 button.
MENU ;
SET ;
„ The last image appears on the screen.
2. Select the image that you want to cancel protection
with the e / f buttons.
3. Press the MENU button.
4. Select [Protect] with the c / d buttons, and press the SET button.
5. Select [Single] or [All] with the e / f buttons, and press the SET button.
6. Select [Cancel Protect] with the e / f buttons, and press the SET button.
„ The removal of image protection is executed and the camera returns to the
playback mode.
„ Formatting an SD/SDHC memory card overrides protection, and erases all images regardless of
their protected status.
EN-24
Erasing Images
Erasing a single image / Erasing all images
1. Press the 7 button.
„ The last image appears on the screen.
2. Select the image you want to erase with the e /
f buttons.
3. Press the MENU button.
4. Select [Delete] with the c / d buttons, and press
the SET button.
5. Select [Single] or [Al ] with the e / f buttons,
and press the SET button.
„ [Single]: Erases the selected image or the
last image.
„ [Al ]: Erases all of the images except for the
protected images.
6. Select [Execute] with the e / f buttons, and
press the SET button.
„ To not erase, select [Cancel], and press the
SET button.
7. To exit from the menu, press the MENU button.
MENU ;
MENU ;
SET
SET
;
;
EN-25
MENU OPTIONS
Capture Menu
This menu is for the basic settings to be used when capturing still images.
4
MP
AUTO
MENU ;
SET
;
MENU ;
SET
;
1.
2.
3.
4.
Press the ON/OFF button to turn the power on.
Press the MODE button, and set the camera mode to any scene mode.
Press the MENU button to enter the [Capture] menu.
Select the desired option item with the c / d buttons, and press the SET button to
enter its respective menu.
„ The selectable items may vary in different capture modes.
5. Select the desired setting with the e / f buttons, and press the SET button.
6. To exit from the menu, press the MENU button.
Size
This sets the size of the image that will be captured.
* 14M / 8M / 4M / 2M / VGA
ISO
This sets the sensitivity for capturing images. When the sensitivity is raised (and the
ISO figure is increased), photography will become possible even in dark locations, but
the more pixelated (grainier) the image will appear.
* Auto / ISO100 / ISO 200 / ISO 400 / ISO 800 / ISO 1600 / ISO 3200
Quality
This sets the quality (compression) at which the image is captured.
* Fine / Standard / Economy
W. Balance
This sets the white balance for a variety of lighting conditions and permits images to be
captured that approach the conditions that are seen by the human eye.
*Auto / Incand. / Fluoresc.1 / Fluoresc.2 / Daylight / Cloudy / Manual WB
Sharpness
This sets the sharpness of the image that will be captured.
* Hard / Standard / Soft
EN-26
Color
This sets the color of the image that will be captured.
* Standard / Vivid / Sepia / B&W / Blue / Red / Green / Yellow / Purple
Saturation
This sets the saturation of the image that will be captured.
* High / Standard / Low
Metering
This sets the metering method for calculating the exposure.
* Center:
Averages the light metered from the entire frame, but gives greater
weight to the subject matter at the center.
* Spot:
A very small portion of the center of the screen is measured to
calculate the correct exposure.
* Average:
The exposure is measured all of the image area.
Capture Md.
This sets the recording method at the time of capturing images.
* Single:
Captures one image at a time.
* Continuous:
Permits continuous capture of up to 3 images.
* AEB:
Permits 3 consecutive images in the order of standard exposure,
underexposure and overexposure compensation.
* Album Shot:
Creates an album-like layout to combine 3 shots into a single
image.
* Burst:
Permits continuous photography while pressing and holding the
shutter button. As long as you hold the shutter button pressed,
images are captured until the memory capacity is exhausted.
* Cont.flash:
Permits continuous capture of up to 3 images with flash.
* Pre-shot:
Select a background by 1st shot, the image shown on display will
be transparent, then take the 2nd shot on the basis of 1st image.
Image of 1st shot is only a guiding tool, it won't be saved on SD
card. Normally this function is used when taking a portrait picture
and the background is selected by the model instead of the
photographer.
* Coupl.shot:
Uses separate areas to combine two shots. You can include
yourself in the shot.
* Burst 30fps:
Permits continuous capture of up to 30 images in the resolution
640 x480 within 1 second.
Quick Shot
If this function is set to “On”, the camera takes a quick shot without focusing.
* On / Off
EN-27
Digi. Zoom
This sets whether or not to use digital zoom at the time of photography.
* On / Off
Find Blur
Refer to the section in this manual titled “Find Blur Function” for further details.
* On / Off
Date Print
The date of recording can be printed directly on the still images. This function must be
activated before the image is captured.
* On / Off
Setup
Refer to the section in this manual titled “Setup Menu” for further details.
EN-28
Video Menu
This menu is for the basic settings to be used when recording video clips.
MENU ;
SET
;
MENU ;
SET
;
1. Press the MODE button, and set the camera mode to [ ].
2. Press the MENU button to enter the [Video] menu.
3. Select the desired option item with the c / d buttons, and press the SET button to
enter its respective menu.
4. Select the desired setting with the e / f buttons, and press the SET button.
5. To exit from the menu, press the MENU button.
Size
This sets the size of the video clip that will be captured.
* HD / VGA / QVGA
Quality
This sets the quality (compression) at which the video clip is captured.
* Fine / Standard
Color
This sets the color of the video clip that will be captured.
* Standard / Vivid / Sepia / B&W / Blue / Red / Green / Yellow / Purple
Audio
This sets whether or not to record audio at the time of video recording.
* On / Off
Digi. Zoom
Refer to the section in this manual titled “Digi. Zoom” in Capture Menu for further details.
Setup
Refer to the section in this manual titled “Setup Menu” for further details.
EN-29
Playback Menu
In the [7] mode, choose which settings are to be used for playback.
MENU ;
SET
;
MENU ;
SET
;
1. Press the 7 button.
2. Press the MENU button.
3. Select the desired option item with the c / d buttons, and press the SET button to
enter its respective menu.
4. Select the desired setting with the e / f buttons, and press the SET button.
5. To exit from the menu, press the MENU button.
Delete
Refer to the section in this manual titled “Erasing Images” for further details.
Fix Red Eyes
Refer to the section in this manual titled “Removing Red-eye” for further details.
Dynam. Light.
Refer to the section in this manual titled “Dynamic Lighting Feature” for further details.
Slide Show
This function enables you to play back your still images automatically in order one
image at a time.
* 3 Sec. / 5 Sec. / 10 Sec.
Rotate
If you wish to rotate a still image 90 degrees to the right, select +90°; if you wish to
rotate it 90 degrees to the left, select -90°. Video clips cannot be rotated.
* +90° / -90°
Protect
Refer to the section in this manual titled “Protecting Images” for further details.
Voice Memo
Refer to the section in this manual titled “Attaching Voice Memos” for further details.
Resize
Resizes a previously saved image. Resizing replaces the original image with the
changed image. It is only possible to resize to a smaller size.
EN-30
Qual. Change
Changes the quality (compression) of a recorded image. Compress images down to half
of their size or less, overwrite old size images with newly compressed images. It is only
possible to reduce the image quality/size, never to increase it.
Setup
Refer to the section in this manual titled “Setup Menu” for further details.
EN-31
Setup Menu
Set your camera’s operating environment.
MENU ;
SET
;
MENU ;
SET
;
1. Press the MODE button, and set the camera mode to [
] or [ ]; or press the 7
button.
2. Press the MENU button.
3. Select the [Setup] at the end of the Menu with the c / d buttons, and press the SET
button.
4. Select the desired option item with the c / d buttons, and press the SET button to
enter its respective menu.
5. Select the desired setting with the e / f buttons, and press the SET button.
6. To exit from the menu, press the MENU button.
Date/Time
Refer to the section in this manual titled “Setting the Date and Time” for further details.
Language
Refer to the section in this manual titled “Choosing the Language” for further details.
Auto Off
If no operation is performed for a specific period of time, the power to the camera is
automatically turned off. This feature is useful for reducing battery usage.
* Off / 1 Min. / 2 Min. / 3 Min.
Beep
This sets whether or not to mute the camera sound each time you press the camera's
buttons.
* On / Off
Display
This sets the image information display state.
* Default / All / Off
EN-32
Video Out
This sets your camera to match the system of the equipment that you are going to
connect to the camera.
* NTSC / PAL
Fr. No. Reset
This creates a new folder. The captured images are recorded to the newly created
folder from number 0001.
* Execute / Cancel
Light Freq.
This camera supports different lighting frequencies: 50 Hz and 60 Hz. When
photographing under fluorescent lighting, select the correct frequency setting
depending in your local area's voltage.
* 50 Hz / 60 Hz
LCD Bright.
Select a brightness level for the LCD monitor.
* Standard / Bright
Format
Refer to section in this manual titled “Formatting the Memory Card or Internal Memory”
for further details.
Media Info.
This displays the free capacity of the internal memory or the memory card.
Sys. Info.
This displays the firmware version of the camera.
Sys. Reset
This returns all basic settings to the camera’s default settings.
* Execute / Cancel
EN-33
TRANSFERRING FILES TO YOUR
COMPUTER
System Requirement
Windows
„
„
„
„
„
„
Pentium III 1GHz or equivalent
Windows 7/XP/Vista
512MB RAM
150MB available hard disk space
CD-ROM drive
Available USB port
Macintosh
„
„
„
„
„
„
PowerPC G3/G4/G5
OS 10.3.9 or later
256MB RAM (512 MB recommended)
128MB available hard disk space
CD-ROM drive
Available USB port
Downloading Your Files
1. Turn on your camera.
2. Connect the camera to your computer with the USB
cable.
3. Select [PC] using the c / d buttons and press the SET
button.
4. From the Windows desktop, double click on “My
Computer”.
5. Look for a new “removable disk” icon.
6. Double click on the removable disk and locate the DCIM folder.
„ Your recorded images and video clips will be inside the folders of DCIM folder.
„ Copy&Paste or Drag-N-Drop image and video files to a folder on your computer.
Mac users: Double-click the “untitled” or “unlabeled” disk drive icon on your desktop.
iPhoto may automatically launch.
USING THE CAMERA AS A PC CAMERA
Your camera can act as a PC camera, which allows you to videoconference with
business associates, or have a real-time conversation with friends or family. Your
computer system must include the items, Microphone, Sound card, Speakers or
headphones, Network or Internet connection.
„ Using the camera as a PC camera, Service Pack 3 is suggested to the users of Windows XP,
Service Pack 3 can be downloaded by visiting http://WWW microsoft com/.
EN-34
EDITING SOFTWARE INSTALLATION
Softwares are included on the CD-ROM:
ArcSoft MediaImpression™ - Easily, creatively, and productively manage your
multimedia files. Create your own movies or photo slide shows, and share your photo,
video and music files easily through simple email attachments or popular photo printing
and video sharing websites.
Print Creations - brings you a family of fun and easy print-project software that brings
out the creativity in you. You can personalize the designs with your own digital pictures
and text based on professionally designed templates and layouts. Projects can be
printed at home or saved as image files for sharing with family and friends by email or
the web.
To install software:
1. Insert the CD-ROM that came with the camera into your CD-ROM drive.
The welcome screen appears.
2. Click the respective software name.
Follow the on-screen instructions to complete the installation.
„ For more information about the operation of the software, refer to its respective help
documentation.
„ For Windows 7/XP/Vista users, please make sure to install and use the software in
“Administrator” mode.
„ The software is not supported by Mac.
EN-35
SPECIFICATIONS
Item
Description
Image sensor
1/2.33” CCD sensor (14.0 megapixels)
Image resolution
Still image
14M (4288X3216), 8M(3264 x 2448), 4M (2304x1728),
2M(1600 x 1200), VGA(640 x 480)
Video clip
HD(720p)/30fps, VGA(640x480)/30fps, QVGA(320x240)/30fps
LCD monitor
2.7” full color TFT LCD (230K pixels)
Recording media
32MB internal memory (23MB available for image storage)
Supports SD/SDHC memory card (1 ~ 32GB) (optional)
File format
DCF, JPEG (EXIF 2.2), Motion-JPEG (AVI), HD720p/30fps
Lens
5x optical zoom lens
Aperture range: 2.8(W) - 6.5(T)
Focal length: 4.70mm - 23.5mm (equivalent to 26mm - 130mm on
a 35mm camera)
Focus Range
Macro: 0.2m~Inf.(W) 0.6m~Inf. (T)
Normal: 0.6m~Inf. (W) 1m~Inf. (T)
Shutter speed
2~1/2000 Sec.
Digital zoom
6x (Capture mode)
4x (Playback mode)
Terminals
USB/AV OUT
(2 in 1 terminal)
Power supply
Rechargeable Lithium-ion battery (3.7V)
Battery Charging
environment
Temperature
0°C - 40°C(32°F to 104°F)(Charging)
Dimensions
Approx. 96.8x 57.5 x 18.5mm (without protruding parts)
Weight
Approx. 110g (without battery and memory card)
* Design and specifications are subject to change without notice.
EN-36
APPENDIX
Possible Number of Shots
Possible number of shots (still image)
The table shows the approximate shots that you can capture at each setting based on
the capacity of the internal memory and the SD/SDHC memory card.
Size
4288 x 3216
3264 x 2448
2304 x 1728
1600 x 1200
VGA
640 x 480
Quality
Fine
Standard
Economy
Fine
Standard
Economy
Fine
Standard
Economy
Fine
Standard
Economy
Fine
Standard
Economy
SD/SDHC memory card capacity
Internal
Memor
y
1GB
2GB
4GB
SDHC
8GB
SDHC
16GB
SDHC
32GB
SDHC
2
6
12
4
9
18
8
15
29
14
28
51
57
94
124
140
273
533
215
405
780
362
676
1268
634
1194
2159
2417
3965
5206
281
548
1069
431
812
1562
725
1354
2539
1269
2390
4323
4838
7938
10421
564
1098
2139
864
1626
3127
1451
2710
5083
2541
4784
8652
9682
15885
20885
1132
2205
4294
1735
3263
6276
2913
5439
10200
5099
9600
17362
19429
31876
41848
2272
4422
8612
3481
6545
12587
5843
10909
20455
10227
19251
34817
38962
63923
83920
4430
8621
16790
6787
12760
24539
11393
21267
39877
19938
37531
67876
75957
99999
99999
Possible recording time / sec (video clip)
Size
HD
1280 x 720
Quality
Internal
Memory
SD/SDHC memory card capacity
1GB
2GB
4GB
SDHC
8GB
SDHC
16GB
SDHC
32GB
SDHC
Fine
00:00 04 00 04 07 00:08:16 00:16 32 00:33:12 01 06 35 02 09:48
Standard
00:00:07 00 07:46 00:15:33 00 31 08 01:02:30 02 05 20 04 04 20
Fine
00:00 07 00 07:46 00:15:33 00 31 08 01:02 30 02 05 20 04 04:20
640 x 480
Standard
00:00:13 00:13 54 00:27:51 00 55:44 01:51:50 03:44:17 07:17:15
Fine
00:00 22 00 22 59 00:46:00 01 32:05 03:04:47 06:10 33 12 02:24
320 x 240
Standard
00:00 33 00 34 06 01:08:16 02:16:38 04 34:11 09 09 51 17 51:57
VGA
* The table above shows the approximate maximum recording times. These are the total times for all
clips. A video recording will stop automatically when a video clip becomes approx. 4GB or 25
minutes.
* We recommend a memory card of at least 10MB/Sec write speed to prevent auto stop or
unexpected results. If you experience an error using a slower SD/SDHC memory card, you can set
your camera’s video recording to QVGA (320 x 240) and standard quality.
* SDHC Class6 or above is required for HD movie recording.
EN-37
Troubleshooting
Refer to the symptoms and solutions listed below before sending the camera for repairs.
If the problem persists, contact your local reseller or service center.
Symptom
Cause
The power does not come
on.
The battery is not inserted.
Insert the battery correctly.
The battery is exhausted.
Recharge the battery.
The battery is not fully charged.
The battery is not used for an
The battery runs out quickly.
extended period of time after
being charged.
The battery or camera feels
warm.
Long period of continuous use of
the camera or the flash.
Solutions / Corrective Actions
Fully charge the battery and
discharge it for at least one
complete cycle before use to
maximize its performance and
lifetime.
-----
The shutter button is not pressed
all the way down.
Even if press the shutter
The memory card does not have
button, the camera does not
any free capacity.
take a picture.
The memory card is
write-protected.
Press the shutter button all the
way down.
Images do not appear on
the LCD monitor.
LCD monitor is dark.
Adjust the brightness of the
LCD monitor in the menu.
The lens is dirty.
Wipe clean with a soft, dry cloth or
lens paper.
The distance to the subject is
smaller than the effective range.
Get your subject within the
effective focus range.
Although it is set to auto
focus, it does not focus.
You played back a memory card
The contents on the memory
that was not formatted by this
card cannot be played back.
camera.
Files cannot be deleted.
Insert a new memory card, or
delete unwanted files.
Remove the write-protection.
Insert a memory card that was
formatted on this camera.
The file is protected.
Cancel protection.
The memory card is
write-protected.
Remove the write-protection.
Even when the camera’s
buttons are pressed, it does The battery is running low.
not operate.
Recharge the battery.
The date and time are
wrong.
Set the correct date and time.
Cannot download images.
The correct date and time is not
set.
Check whether the hard disk has
space for running Windows, and
The free space on the hard disk in
if the drive for loading image files
your computer may be
has a capacity at least that of the
insufficient.
memory card inserted in the
camera.
No power supply.
EN-38
Recharge the battery.
The available flash settings in different photography modes:
Program AE
Auto
TV
AV
Intelligent Scene
Smile Detection
Anti-shake
Panorama PanCapture
Skin Soften
De-blemish
Portrait Man
Portrait Lady
Landscape
Scene Mode
Sports
Night Portrait
Night Scene
Candlelight
Fireworks
Text
Sunset
Sunrise
Splash Water
Flow Water
Snow
Beach
Pets
Natural Green
Single
T Continuous
U AEB
- Album Shot
Capture
/ Burst
Mode
. Cont.flash
+ Pre-Shot
, Coupl.shot
Burst 30fps
K Auto
AF Tracking
Face Detect
Focus Mode
Macro
Super Macro
Q Infinity
b
Auto
O
O
O
O
X
X
O
O
X
X
X
X
X
X
X
X
X
X
X
X
X
O
X
X
O
O
X
O
X
X
O
X
X
O
O
X
O
O
O
O
X
O
a
d
c
`
_
Flash On Flash Off Red-eye Slow Sync Pre-flash
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
X
X
X
X
O
X
X
X
O
O
O
O
O
O
O
O
O
O
X
O
O
X
X
X
O
O
X
X
X
O
O
X
X
X
O
O
X
X
X
O
X
X
X
X
O
X
X
X
X
O
O
X
X
X
O
X
X
X
X
O
X
X
X
X
O
X
X
X
X
O
X
X
X
X
O
X
X
X
X
O
X
X
X
O
O
O
O
O
X
O
X
X
X
X
O
X
X
X
O
O
O
O
O
O
O
O
O
O
X
O
X
X
X
O
O
O
O
O
X
O
X
X
X
X
O
X
X
X
O
O
O
O
O
X
O
X
X
X
O
X
X
X
X
O
O
O
O
O
O
O
O
O
O
X
O
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
X
X
X
O
O
O
O
O
* This table is for reference only and varies according to different combination of photography
modes.
* O: Available X: Unavailable
EN-39
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising