Strain sensitive cable intrusion detection sensor

FPS
TM
Datasheet
FPS
Strain sensitive cable
intrusion detection sensor
Features & Benefits
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Advanced signal processing
Detects cutting, climbing and lifting
Terrain following sensor
High Probability of detection (Pd)
Low Nuisance Alarm Rate (NAR)
Audio assessment of alarms
Optional armored sensor cable
available
Dual zone (2) processor
Quick and easy to install or repair
Proven in thousands of applications
worldwide
EDAPT (Environmentally Derived
Adaptive Processing Technique)
Copper and fiber sensor network option
Audio carried on fiber sensor network
Easy integration to Security
Management System (SMS)
fence and wall-mounted sensors
Description
FPS (Fence Protection System) strain sensitive cable sensor system detects mechanical
disturbances on the fence caused by cutting, climbing or lifting. Advanced signal
processing extracts the maximum amount of data from the fence. More information
means better alarm decisions.
Application
The FPS sensor cable is equally sensitive throughout its entire length. This linear sensor
enables it to be tailored t the design of the fence on site.
Datasheet
FPS I Strain sensitive cable intrusion detection sensor
Outside
Sheath
Outer
Conductor
Inner
Dielectric
Conductor
Filler
jacket of the cable is a made from high density polyethylene
rugged material that is resistant to ultraviolet rays. The MEX
HOW IT WORKS
cable connects directly to the zone processor card with a plug
The FPS processor connects to two transducer sensor cables,
and is mounted on or near the fence in the middle of two detection zones (left and right). Mechanical disturbances detected by
the sensor cable are sent to the FPS processor. The processor
removable terminal block.
Features:
• Uniform sensitivity and easy to repair
contains the circuitry that analyzes the detected disturbance. The
• Linear sensor - tailor senstivity as required
electronics are designed to match the characteristics of the sen-
• Flexibility - change zone configurations easily
sor cable input and only report events based on signals that are
similar to the disturbances caused by climbing, cutting or lifting the
fence fabric.
Helisensor - ruggedized transducer sensor
The FPS processor “looks” at a broad spectrum of frequencies:
cable
80 Hz to 3000 Hz. This enables the processing logic to recognize
The Helisensor is the MEX cable encased in a 0.56 in. (1.4
the signals generated by a climb (low frequency) to the signals
cm) flexible metallic jacket, designed for use with the Senstar
generated by a cut (high frequency). The FPS processing logic
FPS series of signal processors. Helisensor is designed to be
is also able to distinguish between intrusion attempts and most
used in demanding areas where vandalism may be a problem
disturbances caused by environmental effects such as wind, rain,
or industrial sites where physical damage can occur. Heli-
and extremes of temperature.
sensor can be attached to razor ribbon, concertina or barbed
wire. Helisensor is available in 328 ft. (100 m) lengths which
microphonic electret Transducer (MEX) cable
MEX cable is a 0.138 in. (3.5 mm) coaxial cable specially
can be coupled together for longer zones up to 984 ft. (300 m)
each.
Special
manufactured with a permanent electrical charge throughout
hardware is
its entire length. The charge is stored within the cable in the
included for
dielectric material.
end-of-line
terminations
The transducer cable is then
and splicing.
able to act as a long extend-
Helisen-
ed capacitor microphone for
sor can be
which the applied bias voltage
installed on
is supplied internally. Any
a standard
movement in the fence causes
a small voltage to appear at
the sensor cable output. MEX
cable is equally sensitive over the entire zone length. Senstar
tests every foot of cable for sensitivity. With this method of
testing, you are assured the sensor works before incurring
the labour required to place the cable on the fence. The outer
chain link
fence using the outdoor plastic cable ties provided or with
optional stainless steel ties. A minimum bend radius of 3 in.
(7.62 cm) provides for service loops and sensitivity enhancing
arrangements.
Datasheet
FPS I Strain sensitive cable intrusion detection sensor
FPS-2-2M/AP - advanced signal processor
The FPS-2-2M/AP processors communicate with the MX Mul-
• Armored sensor cable
• Protects from physical damage and vandalism
• Easy to install
• Can be used on “razor ribbon”
tiplex Control Unit or the Data Collection Unit (DCU) via the
multiplex transponder built into the processor. The
communication is bi-directional from the MX or DCU utilizing the exclusive Senstar CEnDe communications protocol.
Control functions are received from the MX or DCU unit and
sensor status messages are returned to the MX or DCU. All
of the communication functions are performed on a single pair
FPS processors
of wires daisy-chained from processor to processor.
The FPS dual zone processors are available in three models,
The FPS-2-2M/AP processor zone cards have both a sensi-
one with relay outputs; two using multiplexed communication.
tivity adjustment for each zone and a count setting for each
• FPS-2-2R (Relay)
• FPS-2-2M/AP (Multiplex)
zone. The standard FPS processing uses pattern recognition
to determine those signals that represent a threat versus
those generated by other sources such as wind, rain, etc.
• FPS-5 (Multiplex)
The FPS dual zone processors contain two zone processor cards, one main board and one transponder. The zone
processor cards each have adjustments for the sensitivity of
that particular zone. The processor cards are interchangeable.
The alarm threshold (count setting) is set in software in the MX
Control Unit or DCU for the FPS-2-2M/AP and FPS-5.
Each tamper proof solid-state dual zone processor controls two
1000 ft. (305 m) zones. The plug-in circuit cards facilitate field
diagnostics by simply exchanging boards.
EDAPT
Most systems make the alarm decision in the processor
utilizing the information from one or two zones. The EDAPT
(Environmentally Derived Adaptive Processing Techniques)
installed in the MX and the DCU uses the environmental
effects being experienced by all of the zones on the system
in the alarm decision process. The alarm threshold is set in
software at the MX or DCU. This technique maintains a high
Pd while greatly reducing the nuisance alarm rate.
The FPS dual zone processor has built-in lightning protection
on all input and output lines utilizing gas discharge tubes and
transient bypasses. The processor housings are made of cast
FPS-5 - advanced signal processor with
integrated fiber optic communications
aluminum with all openings gasketed and sealed for a weath-
The FPS-5 processor
contains a fiber optic
transponder that sends the
detected events via a fiber
optic network to the MXF
or the DCUF which allows
multiplexing or bi-directional communications over a
er-tight fit.
The processor and signal cable will initiate a tamper alarm by
removing the cover or cutting or shorting the sensor cable.
The tamper signal is sent by the processor to the alarm monitoring and control unit.
Each zone processor provides an audio representation of the
signal received through the sensor cable. This audio signal
redundant ring of fiber.
is multiplex switched on alarm or manually switched onto an
Each FPS-5 processor validates the communication packet
audio bus to enable the control room personnel to hear the
activity on the fence and assess the situation. The patented
process used by Senstar to produce our electret cable provides
a very quiet ambient noise level which results in a very clear
audio signal from the sensor. The differential between quiet
and alarm also provides a very high signal to noise ratio which
is very important in reducing nuisance alarms.
before re-transmitting the information to the next processor.
The FPS-5 audio signal is digitized and interleaved with the
data packets on the same fiber optic cable. This technique
eliminates the need for a dedicated audio bus.
Technical Specifications
MEX cable
Type:
• Two conductor coaxial
• Outside diameter: 0.138 in. (3.5 mm)
• Life expectancy: 10 years
• Half life sensitivity: 40 years
repair:
• Copper-shielded transducer service kit
• No heat gun or soldering required
supervision:
• Constant impedance monitoring
• EOL kit provided with cable
attachment: Ultraviolet resistant cable ties furnished with cable
helisensor
Type: Outside diameter: 0.56 in. (1.4 cm)
CONNECTION / ATTACHMENT:
• Conduit fitting on processor enclosure
• Ultraviolet resistant cable ties furnished with cable or stainless steel
ties available
Datasheet
fps-5
tamper alarm actuation: Activated by either enclosure switch
or transducer cable fault (shorting or cutting)
remote testing: Built-in self-test generator simulates actual
intrusion signals
input power isolation: Built-in DC to DC converter
allows isolated signal and power grounds
communications: Integrated fiber optic transceiver
power requirements: 12 - 24 VDC, 140 mA
operating temperature: -40°F to +158°F (-40° to
+70°F)
enclosure: Cast aluminum
size: 9 W x 8 H x 4.5 in. D (23 W x 20 H x 11 cm D)
weight: 7 lbs. (3.2 kg)
PART
PRODUCT
TYPE
02-130001
FPS-2-2R
Dual zone signal processor, relay
outputs
02-130005
FPS-2-2R
Dual zone signal processor, relay
outputs, for Helisensor cable
02-130002-1
FPS-2-2M/
AP
Dual zone signal processor,
multiplex output, EDAPT advanced
processing
02-130006-1
FPS-2-2M/
AP
remote testing: Built-in self-test
generator simulates actual intrusion signals
Dual zone signal processor,
copper multiplex output, EDAPT
for Helisensor cable
02-130015
FPS-5
Dual zone signal processor, F/O
multiplex output, EDAPT
input power isolation: Built-in DC to DC converter allows
isolated signal and power grounds
02-130016
FPS-5
audio assessment: Audio information from transducer cable is
provided and multiplex switched to isolated audio bus
Dual zone signal processor, F/O
multiplex output, EDAPT for
Helisensor cable
100MEX
Sensor cable
100 m FPS sensor cable with TSK
and cable ties
communications: Integrated transponder
200MEX
Sensor cable
power requirements:
• +12.0 to 16.0 VDC, 30 mA, Ripple ±0.5 Vpp
• Provided by the MX / DCU series control unit
200 m FPS sensor cable with TSK
and cable ties
300MEX
Sensor cable
300 m FPS sensor cable with TSK
and cable ties
100 MHS
Sensor cable
100 m sensor cable in
conduit with EOL condulet and
cable ties
100BNS
Lead-in
cable
82-210000
Gate option
Telegate telescoping sensor cable
retractor for sliding gates
02-12781402
Gate option
Gate by-pass unit
Dow
compound
#4
Cable
accessory
operating temperature: -40°F to +158°F (-40°C to +70°F)
E6FG0300
size: 9 W x 8 H x 4.5 in. D (23 W x 20 H x 11 cm D)
Power
supply
Indoor-rated UPS for FPS sensors,
1.2 A output
02-150400
Power
supply
Indoor-rated UPS for FPS sensors,
4.0 A output
supervision:
• Constant impedance monitoring
• EOL kit provided with cable
fps-2-2m/ap
tamper alarm actuation: Activated by either enclosure switch or
transducer cable fault (shorting or cutting)
wire entry:
• 0.75 in (1.9 cm) flexible weather-proof conduit fitting for power and
alarm cables
• Gasketed compression bulkhead fitting for transducer cables
weatherproofing:
• Cast aluminum enclosure
• 0.25 in. (6.3 mm) minimum thickness
• All openings gasketed and sealed
• Conformal coated circuit boards, lightning protection
• Input / output lines protected by gas discharge arrestors and / or
transorbs (90 V, 5000 Amp)
weight:
• 7 lbs. (3.2 kg)
• Excess of 40,000 hours MTBF
DESCRIPTION
30 m non-sensitive cable
Sealant for TSK, seals 10 TSK
units
Note: Signal processors are also available in single-zone
versions, contact Senstar for part numbers.
Specifications are subject to change without prior notice.
ISO 9001:2008 - CGSB Registered Certificate 95711 - Canadian manufacturing facility only.
Version: DAS-G2/A-IN-R7-E-05/13
Copyright ©2013. All rights reserved. Features and specifications are subject to change
without notice. The Senstar name and logo are registered trademarks of Senstar Corporation.
www.senstar.com

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project