A T T E N T I O N !!!

A T T E N T I O N !!!
CD9180 / English manual
LOCATION OF CONTROLS
1. Dir UP / ASP button
9. Battery compartment
2. EQ button
10. Open knob
3. MODE / PROG button
11. Volume knob
4. SKIP / SEARCH DN button
12. Phone jack
5. STOP button
13. DC jack
6. PLAY / PAUSE button
14. Recharge switch
7. SKIP / SEARCH UP button
15. Recharge Indicator
8. LCD display
PREPARATION BEFORE USING
Battery Installation
A T T E N T I O N !!!
On operation with standard/conventional batteries, be sure that the
charging switch „RECHARGE“ (14) is on „OFF“ position, otherwise the
batteries may become hot and may explode.
ENG 1
CD9180 / English manual
1. Open Battery Compartment cover.
2. Insert 2 batteries ( UM-3, “AA”, LR6 or equivalent ) in the correct polarity as indicated.
(Heavy duty batteries are recommended).
3. Close the cover properly.
*In order to operate the player on batteries, the optional AC/DC adaptor must be
disconnected from the DC 4.5V Jack.
AC—
—DC Adaptor
*Before connection, make sure the AC voltage of the adaptor correspond to your local AC
outlet voltage.
1. Plug the DC output of the adaptor to the DC 4.5V jack.
2. Connect the adaptor (4.5V/600mA with polarity
) to a power outlet.
RECHARGEABLE BATTERY OPERATION
This unit can fully recharge the specified rechargeable battery, in approximately 15 hours.
The rechargeable batteries (NOT supplied) should be recharged before they are used for the
first time because they are low in power or if they have not been used for a long period (over
60 days).
1. Open the battery compartment cover and insert two of the recommended
rechargeable batteries, matching polarity. (1.2V 650mA).
(Both batteries must be of rechargeable nickel-cadmium type, otherwise the
batteries may explode or leak.)
2. Plug in the AC adaptor and set the Recharge switch to ON position to start charging.
(Use only the AC adaptor supplied with the set for charging.)
3. After 15 hours. Please unplug the AC adaptor and switch the Recharge switch to the
off
position.
(Do not charge continuously for 24 hours or more. Doing so can cause the
performance of the rechargeable battery to deteriorate.)
Note : • You may play DISCS whilst charging the batteries.
4. If the operating time decreases drastically even when the rechargeable
nickel-cadmium
batteries are properly recharge, purchase a new set of rechargeable nickel-cadmium
batteries.
5. When charging for the first time or after a long time, playing time may be reduced. In
this case, charge and discharge the batteries several times.
ENG 2
CD9180 / English manual
DISC PLAYING
Sound Effects
During playback you can choose between the following Sound Effects:” BBS, Pop, Jazz, Rock,
and Classic”, by pressing EQ BUTTON repeatedly. To turn off the effects, press the EQ
BUTTON repeatedly until the “Sound Effects” indicator disappears.
Getting Start
1. Insert the headphone/earphone plug to PHONE JACK.
2. Press the OPEN KNOB, and then the door opens, put a disc into the CD compartment with
label side upward.
3. Push the disc gently around the centre area until it clicks so that the disc fits into the pivot.
(To remove the disc: pick up the disc, holding the edge, while pressing the pivot gently.)
4. Close the door and press the PLAY/PAUSE BUTTON once.
5. The Display will show the total number of tracks/files/directories of the disc, and then it
begins to play the first track/file.
General Operation
PLAY/PAUSE BUTTON
—
Press once to start playback in the original order.
Press again to stop the disc play temporarily.
STOP BUTTON ■
—
Press once to stop playback.
Press again to turn off power.
SKIP/SEARCH BUTTONS
—
Press once to skip to next track
previous track
.
Press continuously to search forward
backward
DIR UP/ASP BUTTON
or back to
or
.
—
ASP ON/OFF ( For CD ).
—
Directory UP ( For MP3 Disc ).
Resume function
This player is equipped with a resume function, means CD-disc will automatic start at position,
where CD-disc was stopped by last use. ATTENTION, this function works only, when no other
CD-disc was insert in meantime into the player. If you wish to start with track 1, press FR
button frequently until track 1 shown into display.
Automatic Turn Off (Auto Power Off)
If the player is in STOP mode for approximately 30 seconds, it will turn off automatically.
ENG 3
CD9180 / English manual
Various Playing Modes
MODE BUTTON — There are 3 kinds of function: ( FOR CD ) :
A. Repeat Play
During Play Mode
· Press the MODE BUTTON once to play current track repeatedly.
· The repeat indicator
will appear in the display.
During Play Mode
· Press the MODE BUTTON twice to play the entire disc repeatedly.
· The repeat indicator
will appear in the display.
NOTE – To cancel REPEAT PLAY simply press the MODE BUTTON until the repeat
Indicator disappears.
B. Intro Scan,
During Play Mode
· Press the MODE BUTTON three times.
· The INT indicator will appear in the display.
· Press the PLAY BUTTON to play the first 10 seconds of each track on the disc.
NOTE – To cancel INTRO SCAN, simply press the MODE BUTTON until the INT indicator
disappears.
C. Random Play
During Play Mode
· Press the MODE BUTTON four times.
· The SHUF indicator will appear in the display.
· Press the PLAY BUTTON, all the tracks on the disc will be played in random sequence.
After all the tracks have been played, the system will stop automatically.
NOTE – To cancel RANDOM PLAY, simply press the MODE BUTTON until the SHUF
indicator disappears.
MODE BUTTON — There are 3 kinds of function: ( FOR MP3 DISC ) :
A. Repeat Play
During Play Mode
· Press the MODE BUTTON once to play current track repeatedly.
· The repeat indicator
During Play Mode
will appear in the display.
· Press the MODE BUTTON twice to play the ENTIRE DISC repeatedly.
· The repeat indicator
During Play Mode
will appear in the display.
· Press the MODE BUTTON three times to play the current DIRECTORY repeatedly.
· The repeat indicator
will appear in the display.
NOTE – To cancel
REPEAT PLAY, simply press the MODE button until the
repeat indicator disappears.
ENG 4
CD9180 / English manual
B. Intro Scan
During Play Mode
· Press the MODE BUTTON four times.
· The INT indicator will appear in the display.
· Press the PLAY BUTTON to play the first 10 seconds of each track on the disc.
NOTE – To cancel INTRO SCAN, simply press the MODE BUTTON until the INT indicator
disappears.
C. Random Play
During Play Mode
· Press the MODE BUTTON five times.
· The SHUF indicator will appear in the display.
· Press the PLAY BUTTON, all the files on a disc to be played in a random sequence and
after all files are played, system will stop automatically.
NOTE – To cancel RANDOM PLAY, simply press the MODE BUTTON until the SHUF
indicator disappears.
Program Play ( FOR CD )
1. In stop mode, press the PROG BUTTON to make program memory.
” will be displayed, “ 00” means track number to memory and “01” means program
2. “
number.
3. Press
or
button to select the desired track.
4. Press the PROG BUTTON to enter the track into memory, the program numbers which will
be increment one step.
※ The program no. “01” has become “02” on the display.
5. Repeat step 3 and 4 until memory is full. ( 64 tracks )
6. Press
BUTTON to start the program play.
7. To stop the program play, press the STOP BUTTON.
8. For program play in step “ 7 ”, press the PROG BUTTON, then the
9. To check the program memory, in program play mode, press the
BUTTON.
or
BUTTONS.
10. To erase the program memory, open the door or turn off the power.
Program Play ( FOR MP3 )
1. In stop mode, press the PROG BUTTON to make program memory.
2. “
” will be displayed, “ 000” means file number, “01” means program number.
3. Press the DIR UP/ASP BUTTON to select the desired directory, the display will become
“
”, “01” means directory number.
4. Press the
or
BUTTONS to select the desired file.
5. Press the PROG BUTTON to enter the directory and file into memory. The program number
which will be increment one step.
※ The program no. “01” has become “02” on the display.
6. Repeat step 3 and 5 until memory is full. ( 64 files ).
ENG 5
CD9180 / English manual
7. Press
BUTTON to start the program play.
8. To stop the program play, press the STOP BUTTON.
9. For program play in step “ 8 ”, press the PROG BUTTON &
BUTTON.
10. To check the program memory, in program play mode, press the
or
BUTTONS.
11. To erase the program memory, open the door or turn off the power.
※ If you do not need to select directory but only select files, the above step 3 can be
skipped.
Digital Anti- Shock Operation
The DIGITAL ANTI-SHOCK PROTECTION function uses semiconductor memory to prevent
the unit from skipping when the unit is subjected to shocks and vibration during play.
When the PLAY/PAUSE BUTTON is pressed and the power turns on, the “ASP” appears and
the Digital Anti-Shock Protection function turns on automatically.
LOW BATTERY ALERT
When the low battery indicator
appears on the display, please prepare to replace the new
batteries.
Switch off the volume restriction
To protect your hearing, after switching on the device, only reduced volume is available. You
can switch off this “Volume restriction”.
1 »EQ« press and hold.– Display: »HIGH« flashes for 5 seconds.
2 Press again the »EQ« button to switch off the volume restriction.
3 Switch off the “Volume restriction” with »EQ«.
Note: ■ The volume restriction is reactivated after switching off or changing the disk.
SPECIFICATIONS
Output Power
:
≥ 15 mW ( 32 Ω )
Freq. Response
:
100 ~ 20000 Hz
Power Source
:
2×UM-3”AA” LR6 size batteries ( batteries not included )
4.5v(600mA) AC-DC adaptor
Dimensions
:
141mm(W) × 140mm(D) ×26mm(H)
** For improvement purposes, specification and design are subject to change without notice. **
ENG 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising