Cisco Catalyst 3850 Series Switches Data Sheet

Cisco Catalyst 3850 Series Switches Data Sheet
Data Sheet
Cisco Catalyst 3850 Series Switches
The Cisco® Catalyst® 3850 Series is the next generation of enterprise-class stackable
Ethernet and Multigigabit Ethernet access and aggregation layer switches that provide
full convergence between wired and wireless on a single platform. Cisco’s new Unified
Access Data Plane (UADP) application-specific integrated circuit (ASIC) powers the
switch and enables uniform wired-wireless policy enforcement, application visibility,
flexibility and application optimization. This convergence is built on the resilience of
the new and improved Cisco StackWise-480 technology. The Cisco Catalyst 3850
Series Switches support full IEEE 802.3at Power over Ethernet Plus (PoE+),
Cisco Universal Power over Ethernet (Cisco UPOE), modular and field-replaceable
network modules, RJ45 and fiber-based downlink interfaces, and redundant fans and
power supplies. With speeds that reach 10Gbps, the Cisco Catalyst 3850 Multigigabit
Ethernet Switches support current and next-generation wireless speeds and
standards (including 802.11ac Wave 2) on existing cabling infrastructure.
Product Overview
●
Integrated wireless controller capability with:
◦ Up to 40G of wireless capacity per switch (48-port RJ45 models)
◦ Support for up to 100 access points and 2000 wireless clients on each switching entity (switch or stack)
●
24 and 48 10/100/1000Mbps data PoE+ and Cisco UPOE models with energy-efficient Ethernet (EEE)
●
24 and 48 100Mbps/1/2.5/5/10 Gbps Cisco UPOE models with energy-efficient Ethernet (EEE)
●
12- and 24-port 1 Gigabit Ethernet SFP-based models
●
12- and 24-port 1/10 Gigabit Ethernet SFP+-based models
●
48-port 1/10 Gigabit Ethernet SFP+ model with 4 fixed 40 Gigabit Ethernet QSFP+ uplinks
●
Cisco StackWise-480 technology provides scalability and resiliency with 480 Gbps of stack throughput1
●
Cisco StackPower™ technology provides power stacking among stack members for power redundancy1
●
Five optional uplink modules2 with 4 x Gigabit Ethernet, 2 x 10 Gigabit Ethernet, 4 x 10 Gigabit Ethernet3, 8
x 10 Gigabit Ethernet4, or 2 x 40 Gigabit Ethernet QSFP+4 ports
●
Dual redundant, modular power supplies and three modular fans providing redundancy
●
Full IEEE 802.3at (PoE+) with 30W power on all copper ports in 1 rack unit (RU) form factor
●
Cisco UPOE with 60W power per port in 1 rack unit (RU) form factor
1
StackWise and StackPower technologies are not supported on the 48-port SFP+ switch model.
Optional uplink modules are not supported on the 48-port 10G SFP+ switch model.
Compatible only with the 48-port RJ45 models and with the 12-port (or higher) 10 Gigabit capable models.
4
Compatible only with Cisco Catalyst 3850 Multigigabit and 24-port SFP+ switch models.
2
3
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 1 of 35
●
Software support for IPv4 and IPv6 routing, multicast routing, modular quality of service (QoS), Flexible
NetFlow (FNF), and enhanced security features
●
Single universal Cisco IOS® Software image across all license levels, providing an easy upgrade path for
software features
●
Enhanced limited lifetime warranty (E-LLW) with next business day (NBD) advance hardware replacement
and 90-day access to Cisco Technical Assistance Center (TAC) support
Switch Configurations
All switches ship with one of the five power supplies (350WAC, 715WAC, 750WAC, 1100WAC, or 440WDC)5.
Figures 1 through 3 show the Cisco Catalyst 3850 Series Switches.
Figure 1.
Cisco Catalyst 3850 Series Switches
Figure 2.
Cisco Catalyst 3850 Switches with 12 and 24 1/10 Gigabit Ethernet SFP+ Ports
Figure 3.
Cisco Catalyst 3850 Switches with 12 and 24 1 Gigabit Ethernet SFP Ports
5
The 48-port 10G SFP+ switch model will only support dedicated power supplies with front-to-back and back-to-front
configurations.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 2 of 35
Table 1 shows the Cisco Catalyst 3850 Series configurations.
Table 1.
Cisco Catalyst 3850 Series Configurations
Models
Total 10/100/1000 or
SFP or SFP+ Ports
Default AC Power Supply
Available PoE Power
StackWise-480
StackPower
WS-C3850-24T
24
350WAC
-
Yes
Yes
WS-C3850-48T
48
WS-C3850-24P
24 PoE+
715WAC
435W
WS-C3850-48P
48 PoE+
WS-C3850-48F
48 PoE+
1100WAC
800W
WS-C3850-24U
24 UPOE
1100WAC
800W
WS-C3850-48U
48 UPOE
1100WAC
800W
WS-C3850-24XU
24 UPOE
(100Mbps/1/2.5/5/10
Gbps)
1100WAC
580W
WS-C3850-12X48U
48 UPOE (with 12
100Mbps/1/2.5/5/10
Gbps Ports)
1100WAC
630W
WS-C3850-12S
12 SFP
350WAC
WS-C3850-24S
24 SFP
WS-C3850-12XS
12 1/10G SFP+
350WAC
-
WS-C3850-24XS
24 1/10G SFP+
715 WAC
-
WS-C3850-48XS
48 1/10G SFP+
750WAC (front to back)
-
No
No
Network Modules
The Cisco Catalyst 3850 Series Switches support five optional network modules for uplink ports. The default switch
configuration does not include the network module6. At the time of switch purchase the customer has the flexibility
to choose from the network modules described in Table 2.
Figure 4 shows the following network modules:
●
4 x Gigabit Ethernet with Small Form-Factor Pluggable (SFP) receptacles
●
2 x 10 Gigabit Ethernet with SFP+ or 4 x Gigabit Ethernet with SFP receptacles
●
4 x 10 Gigabit Ethernet with SFP+ receptacles (supported only on the 48-port Gigabit Ethernet models or on
the 12-port or higher 10 Gigabit Ethernet models)
Figure 4.
6
Network Modules with Four Gigabit Ethernet, Two 10 Gigabit Ethernet SFP+, or Four 10 Gigabit Ethernet
SFP+ Interfaces
Network modules are not supported on the 48-port 10G SFP+ switch model, which comes with four fixed 40 Gigabit Ethernet
QSFP+ uplinks.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 3 of 35
Figure 5 shows the following network modules:
●
8 x 10 Gigabit Ethernet with Small Form-Factor Pluggable+ (SFP+) receptacles
●
2 x 40 Gigabit Ethernet with Quad Small Form-Factor Pluggable+ (QSFP+) receptacles
Figure 5.
Network Modules with Two 40 Gigabit Ethernet QSFP+ or Eight 10 Gigabit Ethernet SFP+ Interfaces
Table 2.
Network Module Numbers and Descriptions
Product Number
Product Description
WS-C3850-24XU
WS-C3850-12XS
WS-C3850-12X48U
WS-C3850-24XS
C3850-NM-4-1G
4 x Gigabit Ethernet network modules
Supported
Not supported
C3850-NM-2-10G
4 x Gigabit Ethernet/2 x 10 Gigabit Ethernet network modules
Supported
Not supported
C3850-NM-4-10G
4 x Gigabit Ethernet/4 x 10 Gigabit Ethernet network modules
Supported
Supported
C3850-NM-8-10G
8 x Gigabit Ethernet/8 x 10 Gigabit Ethernet network modules
Supported
See note
C3850-NM-2-40G
2 x 40 Gigabit Ethernet network modules
Supported
See note
Note:
The C3850-NM-4-10G module is supported only on the 48-port Gigabit Ethernet models or on the 12-port
or higher 10 Gigabit Ethernet models. The C3850-NM-8x10G and C3850-NM-2x40G modules are supported on the
24-port and 48-port multigigabit switches and also on the 24-port 10G SFP+ switch model. The C3850-NM-4-1G
and C3850-NM-2-10G modules are not supported on the 12-port and 24-port SFP+ models.
Table 3.
Network Module Compatibility Matrix
Models
Network Modules
WS-C3850-24T
C3850-NM-4-1G, C3850-NM-2-10G
WS-C3850-48T
C3850-NM-4-1G, C3850-NM-2-10G, C3850-NM-4-10G
WS-C3850-24P
C3850-NM-4-1G, C3850-NM-2-10G
WS-C3850-48P
C3850-NM-4-1G, C3850-NM-2-10G, C3850-NM-4-10G
WS-C3850-48F
C3850-NM-4-1G, C3850-NM-2-10G, C3850-NM-4-10G
WS-C3850-24U
C3850-NM-4-1G, C3850-NM-2-10G
WS-C3850-48U
C3850-NM-4-1G, C3850-NM-2-10G, C3850-NM-4-10G
WS-C3850-24XU
C3850-NM-4-1G, C3850-NM-2-10G, C3850-NM-4-10G, C3850-NM-8-10G, C3850-NM-2-40G
WS-C3850-12X48U
C3850-NM-4-1G, C3850-NM-2-10G, C3850-NM-4-10G, C3850-NM-8-10G, C3850-NM-2-40G
WS-C3850-12S
C3850-NM-4-1G, C3850-NM-2-10G
WS-C3850-24S
C3850-NM-4-1G, C3850-NM-2-10G
WS-C3850-12XS
C3850-NM-4-10G
WS-C3850-24XS
C3850-NM-4-10G, C3850-NM-8-10G, C3850-NM-2-40G
WS-C3850-48XS
None
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 4 of 35
An SFP+ receptacle supports both 10 Gigabit Ethernet and Gigabit Ethernet modules, allowing customers to use
their investment in Gigabit Ethernet SFP modules and upgrade to 10 Gigabit Ethernet when business demands
change without having to do a comprehensive upgrade of the access switch. In contrast, SFP receptacles can be
used only as Gigabit Ethernet ports, as shown in the examples in Table 4.
Table 4.
Network Module Configuration Examples
Interface Options
Network Module
10 Gigabit Ethernet SFP+ Ports
Gigabit Ethernet SFP Ports
4 x Gigabit Ethernet
0
4
4 x Gigabit Ethernet/2 x10 Gigabit Ethernet network modules
2
0
1
3
2
2
0
4
4
0
0
4
2
2
3
1
1
3
4 x Gigabit Ethernet/4 x10 Gigabit Ethernet network modules
Dual Redundant Modular Power Supplies
The Cisco Catalyst 3850 Series Switches support dual redundant power supplies7. The switch ships with one
power supply by default, and the second power supply can be purchased at the time of ordering the switch or at a
later time. If only one power supply is installed, it should always be in power supply bay 1. The switch also ships
with three field-replaceable fans. (See Figure 6.)
Figure 6.
7
Dual Redundant Power Supplies
The 48-port 10G SFP+ switch model will only support dedicated power supplies with front-to-back and back-to-front
configurations.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 5 of 35
Table 5 shows the different power supplies available in these switches and available PoE power.
Table 5.
Power Supply Models
Models
Default Power Supply
Available PoE Power
24-port data switch
PWR-C1-350WAC
-
PWR-C1-715WAC
435W
48-port full PoE switch
PWR-C1-1100WAC
800W
24-port UPOE switch
PWR-C1-1100WAC
800W
24-port Multigigabit UPOE switch
PWR-C1-1100WAC
580W
48-port Multigigabit UPOE switch
PWR-C1-1100WAC
630W
12-port SFP switch
PWR-C1-350WAC
-
12-port SFP+ switch
PWR-C1-350WAC
-
24-port SFP+ switch
PWR-C1-715WAC
-
48-port SFP+ switch (WS-C3850-48XS-S and
WS-C3850-48XS-E)
PWR-C3-750WAC-R
-
48-port SFP+ switch (WS-C3850-48XS-F-S and
WS-C3850-48XS-F-E)
PWR-C3-750WAC-F
-
48-port data switch
24-port PoE switch
48-port PoE switch
48-port UPOE switch
24-port SFP switch
In addition to the power supplies listed in Table 5, a 440WDC power supply is available as a configuration option
and also as a spare (that is, it can be ordered separately) on all switch models. The DC power supply also delivers
PoE capabilities for maximum flexibility (refer to Table 6 for available PoE budget with DC power supplies).
Customers can mix and match the AC and DC power supplies in the two available power supply slots. Any of these
power supplies can be installed in any of the switches.
Table 6.
Available PoE with DC Power Supply
Model
Number of 440WDC Power Supplies
Total Available PoE Budget
24-port PoE switch
1
220W
2
660W
1
185W
2
625W
24-port Mgig UPoE switch
2
360W
48-port Mgig UPoE switch
2
410W
48-port PoE switch
Power over Ethernet Plus (PoE+)
In addition to PoE (IEEE 802.3af), the Cisco Catalyst 3850 Series Switches support PoE+ (IEEE 802.3at standard),
which provides up to 30W of power per port. The Cisco Catalyst 3850 Series Switches can provide a lower total
cost of ownership (TCO) for deployments that incorporate Cisco IP phones, Cisco Aironet® wireless LAN (WLAN)
access points, or any IEEE 802.3at-compliant end device. PoE removes the need for wall power to each PoEenabled device and eliminates the cost for additional electrical cabling and circuits that would otherwise be
necessary in IP phone and WLAN deployments. Table 7 shows the power supply combinations required for
different PoE needs.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 6 of 35
Table 7.
Power Supply Requirements for PoE and PoE+
24-Port PoE Switch
48-Port PoE Switch
PoE on all ports (15.4W per port)
One PWR-C1-715WAC
One PWR-C1-1100WAC or two PWR-C1-715WAC
PoE+ on all ports (30W per port)
One PWR-C1-1100WAC or two
PWR-C1-715WAC
Two PWR-C1-1100WAC or one PWR-C1-1100WAC and one PWRC1-715WAC
Cisco Universal Power over Ethernet (UPOE)
Cisco Universal Power over Ethernet (Table 8) is a breakthrough technology, offering the following services and
benefits.
●
60W per port to enable a variety of end devices such as Samsung VDI client, BT IP turret systems in trading
floors, Cisco Catalyst compact switches in retail/hospitality environments, personal Cisco TelePresence®
systems, and physical access control devices
●
High availability for power and guaranteed uninterrupted services, a requirement for critical
applications (e911)
●
Lowering OpEx by providing network resiliency at lower cost by consolidating backup power into
the wiring closet
●
Faster deployment of new campus access networking infrastructures by eliminating the need for a power
outlet for every endpoint
Table 8.
Power Supply Requirements for UPOE
UPOE (60W per port) on all
(24 port switch) or max. 30 ports
(48 port switch)
24-Port UPOE Switch
48-Port UPOE Switch
24-Port Multigigabit
UPOE Switch
48-Port Multigigabit
UPOE Switch
One PWR-C11100WAC and one
PWR-C1-715WAC
Two PWR-C11100WAC
Two PWR-C11100WAC
Two PWR-C11100WAC
Cisco Catalyst Multigigabit Ethernet Technology
Cisco Multigigabit Ethernet is a unique Cisco innovation to the new Cisco Catalyst Ethernet Access Switches. With
the enormous growth of 802.11ac and new wireless applications, wireless devices are promoting the demand for
more network bandwidth. This creates a need for a technology that supports speeds higher than 1 Gbps on all
cabling infrastructure. Cisco Multigigabit technology allows you to achieve bandwidth speeds from 1 Gbps through
10 Gbps over traditional Cat 5e cabling or above. In addition, the Multigigabit ports on select Cisco Catalyst
switches support UPOE, which is increasingly important for next-generation workspaces and Internet of Things
(IoT) ecosystems.
Cisco Multigigabit technology offers significant benefits for a diverse range of speeds, cable types, and PoE power.
The benefits can be grouped into three different areas:
●
Multiple speeds: Cisco Multigigabit technology supports autonegotiation of multiple speeds on switch
ports. The supported speeds are 100 Mbps, 1 Gbps, 2.5 Gbps, and 5 Gbps on Cat 5e cable and up to 10
Gbps over Cat 6a cabling.
●
Cable type: The technology supports a wide range of cable types, including Cat 5e, Cat 6, and Cat 6a or
above.
●
PoE power: The technology supports PoE, PoE+, and UPOE for all the supported speeds and cable types.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 7 of 35
For more information, visit http://www.cisco.com/c/en/us/solutions/enterprise-networks/catalyst-multigigabitswitching/index.html.
Benefits
Converged Wired plus Wireless Access
The Cisco Catalyst 3850 is the first stackable access switching platform that enables wired plus wireless services
on a single Cisco IOS XE Software-based platform. With this, Cisco has pioneered a host of rich capabilities such
as high availability based on stateful switchover (SSO) on stacking, granular QoS, security, and Flexible Netflow
(FNF) across wired and wireless in a seamless fashion. Also, the wired plus wireless features are bundled into a
single Cisco IOS Software image, which reduces the number of software images that users have to qualify/certify
before enabling them in their network. The single console port for command-line interface (CLI) management
reduces the number of touch points to manage for wired plus wireless services, thereby reducing network
complexity, simplifying network operations, and lowering the TCO to manage the infrastructure.
Converged wired plus wireless not only improves wireless bandwidth across the network but also the scale of
wireless deployment. Each 48-port Cisco Catalyst 3850 provides 40 Gbps of wireless throughput (20 Gbps on the
24-port/12-port models). This wireless capacity increases with the number of members in the stack. This makes
sure that the network can scale with current wireless bandwidth requirements, as dictated by IEEE 802.11n-based
access points and with future wireless standards such as IEEE 802.11ac. Additionally, the Cisco Catalyst 3850
distributes the wireless controller functions to achieve better scalability. Each Cisco Catalyst 3850 switch/stack can
operate as the wireless controller in two modes (Figure 7):
●
Mobility agent (MA): This is the default mode in which a Cisco Catalyst 3850 switch ships. In this mode the
switch is capable of terminating the CAPWAP tunnels from the access points and providing wireless
connectivity to wireless clients. Maintaining wireless client databases and configuring and enforcing security
and QoS policies for wireless clients and access points can be enforced in this mode. No additional license
on top of IP Base is required to operate in the mobility agent mode.
●
Mobility controller (MC): In this mode, the Cisco Catalyst 3850 switch can perform all the mobility agent
tasks in addition to mobility coordination, radio resource management (RRM), and Cisco CleanAir®
coordination within a mobility subdomain. The mobility controller mode can be enabled on the switch CLI.
IP Base license level is required when the Cisco Catalyst 3850 switch is acting as the mobility controller.
A centrally located Cisco 5508 Wireless LAN Controller (WLC 5508), Cisco Wireless Services Module 2
(WiSM2) (when running AireOS Version 7.3), and Wireless LAN Controller 5760 can also perform this role
for larger deployments.
With mobility agents located in the wiring closets providing 40 Gbps of wireless per 48-port Gigabit Ethernet
RJ45 switch (n x 40 Gbps for a stack of n switches) and mobility controllers managing some of the central
wireless functions, the converged access-based wireless deployment provides best-in-class scalability for
wireless and significantly improved wireless throughput.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 8 of 35
Figure 7.
Mobility Controller (MC) and Mobility Agent (MA)
For more information about Converged Wired plus Wireless Access, refer to the Q&A document here:
http://www.cisco.com/c/dam/en/us/products/collateral/switches/catalyst-3850-series-switches/cisco-catalyst-3850series-switches-faq.pdf.
Distributed Intelligent Services
Flexible NetFlow (FNF)
Full visibility into the wired plus wireless traffic is achieved because of the access point Control and Provisioning of
Wireless Access Points (CAPWAP) tunnel termination on the switch. This helps identify users and user traffic flows
in order to identify potential attackers and take corrective action at the access layer before the attack penetrates
further into the network. This is achieved using FNF, which monitors every single flow entering and exiting the
switch stack for wired and wireless users. It also helps identify the top wired/wireless talkers and enforce
appropriate bandwidth provisioning policies.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 9 of 35
QoS
The Cisco Catalyst 3850 switch has advanced wired plus wireless QoS capabilities. It uses the Cisco modular QoS
command line interface (MQC). The switch manages wireless bandwidth using unprecedented hierarchical
bandwidth management starting at the per-access-point level and drilling further down to per-radio, per-service set
identification (SSID), and per-user levels. This helps manage and prioritize available bandwidth between various
radios and various SSIDs (enterprise, guest, and so on) within each radio on a percentage basis. The switch is
also capable of automatically allocating equal bandwidth among the connected users within a given SSID. This
makes sure that all users within a given SSID get a fair share of the available bandwidth while being connected to
the network. The UADP ASIC enables the hierarchical bandwidth management and fair sharing of bandwidth,
thereby providing hardware-based QoS for optimized performance at line-rate traffic.
In addition to these capabilities, the switch is able to do class of service (CoS) or differentiated services code point
(DSCP) based queuing, policing, shaping, and marking of wired plus wireless traffic. This enables users to create
common policies that can be used across wired plus wireless traffic. The Cisco Catalyst 3850 also supports
downloadable policy names from the Cisco Identity Services Engine (ISE) when a user successfully authenticates
to the network using the ISE.
Security
The Cisco Catalyst 3850 provides a rich set of security features for wired plus wireless users. Features such as
IEEE 802.1x, port security, Dynamic Host Configuration Protocol (DHCP) Snooping and Guard, Dynamic ARP
Inspection, RA Guard, IP Source Guard, control plane protection (CoPP), wireless intrusion prevention systems
(WIPSs), and so on enable protection against unauthorized users and attackers. With a variety of wired plus
wireless users connecting to the network, the switch supports session-aware networking, in which each device
connected to the network is identified as one session, and unique access control lists (ACLs) and/or QoS policies
can be defined and applied using the ISE for each of these sessions, providing better control on the devices
connecting to the network.
Resiliency
Cisco StackWise-480 Technology
Cisco StackWise-480 technology is built on the highly successful industry-leading StackWise® technology, which is
a premium stacking architecture8. StackWise-480 has a stack bandwidth of 480 Gbps. StackWise - 480 uses Cisco
IOS Software SSO for providing resiliency within the stack. The stack behaves as a single switching unit that is
managed by an “active” switch elected by the member switches.
The active switch automatically elects a standby switch within the stack. The active switch creates and updates all
the switching/routing/wireless information and constantly synchronizes that information with the standby switch. If
the active switch fails, the standby switch assumes the role of the active switch and continues to the keep the stack
operational. Access points continue to remain connected during an active-to-standby switchover.
A working stack can accept new members or delete old ones without service interruption. StackWise-480 creates a
highly resilient single unified system of up to nine switches, providing simplified management using a single IP
address, single Telnet session, single CLI, autoversion checking, autoupgrading, autoconfiguration, and more.
StackWise-480 also enables local switching in Cisco Catalyst 3850 Series Switches.
8
StackWise and StackPower technologies are not supported on the 48-port SFP+ switch model.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 10 of 35
Cisco StackPower Technology
The Cisco Catalyst 3850 Series uses the Cisco StackPower9 technology present on the Cisco Catalyst 3850
Series. StackPower is an innovative power interconnect system that allows the power supplies in a stack to be
shared as a common resource among all the switches. Cisco StackPower unifies the individual power supplies
installed in the switches and creates a pool of power, directing that power where it is needed. Up to four switches10
can be configured in a StackPower stack with the special connector at the back of the switch using the StackPower
cable, which is different than the StackWise-480 cables. (See Figure 8.)
Figure 8.
StackWise-480 and StackPower Connectors
StackPower can be deployed in either power-sharing mode or redundancy mode. In power-sharing mode, the
power of all the power supplies in the stack is aggregated and distributed among the switches in the stack. In
redundant mode, when the total power budget of the stack is calculated, the wattage of the largest power supply is
not included. That power is held in reserve and used to maintain power to switches and attached devices when one
power supply fails, enabling the network to operate without interruption. Following the failure of one power supply,
the StackPower mode becomes power sharing.
StackPower allows customers to simply add one extra power supply in any switch of the stack and either provide
power redundancy for any of the stack members or simply add more power to the shared pool. StackPower
eliminates the need for an external redundant power system or installation of dual power supplies in all the stack
members. StackPower is available in LAN Base license level (or higher). For LAN Base, cables need to be
purchased separately.
Foundation for Open Network Environment
The heart of the Cisco Catalyst 3850 is the UADP ASIC with programmability for future features and intelligence
with investment protection. The new ASIC provides the foundation for converged APIs across wired and wireless,
Cisco Open Network Environment, software-defined networking (SDN) readiness and OnePK SDK through
software updates over the product lifetime.
9
Stackpower is not supported on the 48-port 10G SFP+ switch model
Up to nine switches are supported in a star configuration with XPS-2200.
10
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 11 of 35
Software Features and Services on Cisco Catalyst 3850 Series Switches
Software services supported on the Cisco Catalyst 3850 Series Switches can be classified into five broad
categories:
●
Ease of operations
●
Advanced security features
●
Resiliency
●
Application visibility and control
Ease of Operations
The Cisco Catalyst 3850 helps reduce the operating costs through:
●
Cisco Catalyst Smart Operations
●
Easy-to-use deployment and control features
●
Efficient switch operations
●
Network management tools
Cisco Catalyst Smart Operations
Cisco Catalyst Smart Operations are a comprehensive set of capabilities that simplify LAN deployment,
configuration, and troubleshooting. In addition to adaptive, always-on technologies such as StackWise-480 and
StackPower, Cisco Catalyst Smart Operations enable zero-touch installation and replacement of switches, fast
upgrade, and ease of troubleshooting with reduced operational cost. Cisco Catalyst Smart Operations are a set of
features that includes Smart Install, Auto Smartports, Smart Configuration and Smart Troubleshooting to enhance
operational excellence:
●
Cisco Smart Install is a transparent plug-and-play technology to configure the Cisco IOS Software image
and switch configuration without user intervention. Smart Install utilizes dynamic IP address allocation and
the assistance of other switches to facilitate installation, providing transparent network plug and play.
●
Cisco Auto Smartports provide automatic configuration as devices connect to the switch port, allowing
autodetection and plug and play of the device onto the network.
●
Cisco Smart Troubleshooting is an extensive array of debug diagnostic commands and system health
checks within the switch, including Generic Online Diagnostics (GOLD) and Onboard Failure Logging
(OBFL).
●
Embedded Event Manager (EEM) is a powerful and flexible feature that provides real-time network event
detection and onboard automation. Using EEM, customers can adapt the behavior of their network devices
to align with their business needs. This feature requires the IP Base feature set.
Easy-to-Use Deployment and Control Features
●
User experience:
◦ IP service-level agreements (SLAs) enable customers to assure new business-critical IP applications, as
well as IP services that utilize data, voice, and video, in an IP network. This feature requires the IP
Services feature set.
◦ DHCP autoconfiguration of multiple switches through a boot server eases switch deployment.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 12 of 35
◦ Automatic QoS (AutoQoS) simplifies QoS configuration in voice over IP (VoIP) networks by issuing
interface and global switch commands to detect Cisco IP phones, classify traffic, and help enable egress
queue configuration.
◦ Autonegotiation on all ports automatically selects half- or full-duplex transmission mode to optimize
bandwidth.
◦ Automatic media-dependent interface crossover (MDIX) automatically adjusts transmit and receive pairs
if an incorrect cable type (crossover or straight through) is installed.
●
Simplified configuration and connectivity:
◦ Dynamic Trunking Protocol (DTP) facilitates dynamic trunk configuration across all switch ports.
◦ Port Aggregation Protocol (PAgP) automates the creation of Cisco Fast EtherChannel groups or Gigabit
EtherChannel groups to link to another switch, router, or server.
◦ Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with devices that
conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel technology and PAgP.
◦ Unidirectional Link Detection Protocol (UDLD) and aggressive UDLD allow unidirectional links caused by
incorrect fiber-optic wiring or port faults to be detected and disabled on fiber-optic interfaces.
◦ Cisco VLAN Trunking Protocol (VTP) Version 3 supports dynamic VLANs and dynamic trunk
configuration across all switches.
●
Efficient switch operation:
◦ Switching database manager (SDM) templates, VLAN template (specific to LAN Base license level), and
advanced template allow the administrator to automatically optimize the ternary content-addressable
memory (TCAM) allocation to the desired features based on deployment-specific requirements.
◦ Local proxy Address Resolution Protocol (ARP) works in conjunction with private VLAN edge to minimize
broadcasts and maximize available bandwidth.
◦ Stacking master configuration management with Cisco StackWise-480 technology helps make sure that
all switches are automatically upgraded when the master switch receives a new software version.
Automatic software version checking and updating help ensure that all stack members have the same
software version.
◦ Trivial File Transfer Protocol (TFTP) reduces the cost of administering software upgrades by
downloading from a centralized location.
◦ Network Timing Protocol (NTP) provides an accurate and consistent timestamp to all intranet switches.
●
Multicast:
◦ Optimized multicast for wired plus wireless: Cisco Catalyst 3850 offers greater multicast efficiency by
receiving only one multicast stream and replicating it for all connected wired plus wireless devices
connected to that switch.
◦ Internet Group Management Protocol (IGMP) v1, v2, v3 snooping for IPv4: multicast listener discovery
(MLD) v1 and v2 snooping provides fast client joins and leaves of multicast streams and limits
bandwidth-intensive video traffic to only the requestors.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 13 of 35
●
Monitoring:
◦ Remote Switch Port Analyzer (RSPAN) allows administrators to remotely monitor ports in a Layer 2
switch network from any other switch in the same network.
◦ For enhanced traffic management, monitoring, and analysis, the Embedded Remote Monitoring
(RMON) software agent supports four RMON groups (history, statistics, alarms, and events).
◦ Layer 2 traceroute eases troubleshooting by identifying the physical path that a packet takes from source
to destination.
◦ Wireless RF management provides both real-time and historical information about RF interference
affecting network performance across controllers using systemwide Cisco CleanAir technology
integration.
Efficient Switch Operation
Cisco Catalyst 3850 Series Switches, designed and engineered by Cisco, provide optimum power-saving, EEE (on
RJ45 ports), low-power operations for industry best-in-class power management and power consumption
capabilities. The Cisco Catalyst 3850 ports are capable of reduced power modes so that ports not in use can move
into a lower power utilization state. Other efficient switch operation features are:
●
Cisco Discovery Protocol Version 2 allows the Cisco Catalyst 3850 Series Switches to negotiate a more
granular power setting when connecting to a Cisco powered device such as IP phones or access points
than what is provided by IEEE classification.
●
Per-port power consumption command allows customers to specify maximum power setting on an
individual port. Per-port PoE power sensing measures actual power being drawn, enabling more intelligent
control of powered devices.
●
The PoE MIB provides proactive visibility into power usage and allows customers to set different powerlevel thresholds.
Environmental Responsibility
Organizations may choose to turn off access point radios to reduce power consumption during off-peak hours.
The integrated wireless LAN controller avoids the deployment of additional devices in the network.
Network Management Tools
The Cisco Catalyst 3850 Series Switches offer both a superior CLI for detailed configuration and Cisco Prime™
infrastructure for unified wired plus wireless management. Prime infrastructure provides day 0 and ongoing
provisioning, ongoing monitoring and maintenance, configuration templates, and device and user 360-degree
views and serves as the FNF collector for user traffic views using the Prime Assurance Manager module.
For detailed information about Cisco Prime infrastructure, go to
http://www.cisco.com/en/US/products/ps12239/index.html.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 14 of 35
Advanced Security Features
Cisco Catalyst 3850 Series Switches support advanced security features including but not limited to:
●
Protection against attackers:
◦ Port security secures the access to an access or trunk port based on MAC address. It limits the number
of learned MAC addresses to deny MAC address flooding.
◦ DHCP snooping prevents malicious users from spoofing a DHCP server and sending out bogus
addresses. This feature is used by other primary security features to prevent a number of other attacks
such as ARP poisoning.
◦ Dynamic ARP inspection (DAI) helps ensure user integrity by preventing malicious users from exploiting
the insecure nature of ARP.
◦ IP source guard prevents a malicious user from spoofing (that is, taking over) another user’s IP address
by creating a binding table between the client’s IP and MAC address, port, and VLAN, and by using it to
selectively block bogus packets.
◦ The Unicast Reverse Path Forwarding (uRPF) feature helps mitigate problems caused by the
introduction of malformed or forged (spoofed) IP source addresses into a network by discarding IP
packets that lack a verifiable IP source address.
◦ Bidirectional data support on a SPAN port allows the Cisco intrusion detection system (IDS) to take
action when an intruder is detected.
●
User authentication:
◦ Flexible authentication that supports multiple authentication mechanisms, including 802.1X, MAC
authentication bypass, and web authentication using a single, consistent configuration.
◦ RADIUS change of authorization and downloadable calls for comprehensive policy management
capabilities.
◦ Private VLAN edge restricts traffic between hosts in a switch by segregating traffic at Layer 2, turning a
broadcast segment into a nonbroadcast multiaccess like segment. Private VLAN edge provides security
and isolation between switch ports, which helps ensure that users cannot snoop on other users’ traffic.
◦ Multidomain authentication allows an IP phone and a PC to authenticate on the same switch port while
placing them on appropriate voice and data VLAN.
◦ MAC address notification allows administrators to be notified of users added to or removed from the
network.
◦ Mobility and security for secure, reliable wireless connectivity and consistent end-user experience.
Increased network availability through proactive blocking of known threats.
◦ IGMP filtering provides multicast authentication by filtering out nonsubscribers and limits the number of
concurrent multicast streams available per port.
●
ACLs:
◦ Cisco security VLAN ACLs on all VLANs prevent unauthorized data flows from being bridged within
VLANs.
◦ Cisco standard and extended IP security router ACLs define security policies on routed interfaces for
control-plane and data-plane traffic. IPv6 ACLs can be applied to filter IPv6 traffic.
◦ Port-based ACLs for Layer 2 interfaces allow security policies to be applied on individual switch ports.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 15 of 35
●
Device access:
◦ Secure Shell (SSH) Protocol, Kerberos, and Simple Network Management Protocol Version 3
(SNMPv3) provide network security by encrypting administrator traffic during Telnet and SNMP sessions.
SSH Protocol, Kerberos, and the cryptographic version of SNMPv3 require a special cryptographic
software image because of U.S. export restrictions.
◦ TACACS+ and RADIUS authentication facilitates centralized control of the switch and restricts
unauthorized users from altering the configuration.
◦ Multilevel security on console access prevents unauthorized users from altering the switch configuration.
●
Bridge protocol data unit (BPDU) Guard shuts down Spanning Tree PortFast-enabled interfaces when
BPDUs are received to avoid accidental topology loops.
●
Spanning Tree Root Guard (STRG) prevents edge devices not in the network administrator’s control from
becoming Spanning Tree Protocol root nodes.
●
Wireless end-to-end security offers CAPWAP-compliant DTLS encryption to make sure of encryption
between access points and controllers across remote WAN/LAN links.
Resiliency
Borderless networks enable enterprise mobility and business-grade video services. Industry’s first unified network
(wired plus wireless) location services enable tracking of mobile assets and the users of those assets for both
wired plus wireless devices. The true borderless experience is enabled by the following feature sets in the Cisco
Catalyst 3850 Series Switches:
●
High availability
●
High-performance IP routing
●
Superior QoS
High Availability
In addition to StackWise-480 and StackPower11, the Cisco Catalyst 3850 Series supports high-availability features
including but not limited to the following:
●
Cross-Stack EtherChannel provides the ability to configure Cisco EtherChannel technology across different
members of the stack for high resiliency.
●
Flexlink provides link redundancy with convergence time less than 100ms.
●
IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) provides rapid spanning-tree convergence
independent of spanning-tree timers and also offers the benefit of Layer 2 load balancing and distributed
processing.
●
Per-VLAN Rapid Spanning Tree (PVRST+) allows rapid spanning-tree (IEEE 802.1w) reconvergence on a
per-VLAN spanning-tree basis, providing simpler configuration than MSTP. In both MSTP and PVRST+
modes, stacked units behave as a single spanning-tree node.
●
Switch-port autorecovery (“err-disable” recovery) automatically attempts to reactivate a link that is disabled
because of a network error.
*
Stackpower is not supported on the 48-port 10G SFP+ switch model
11
Stackpower is not supported on the 48-port 10G SFP+ switch model
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 16 of 35
High-Performance IP Routing
The Cisco Express Forwarding hardware routing architecture delivers extremely high-performance IP routing in the
Cisco Catalyst 3850 Series Switches:
●
IP unicast routing protocols (static, Routing Information Protocol Version 1 [RIPv1], and RIPv2, RIPng,
Enhanced Interior Gateway Routing Protocol [EIGRP] stub) are supported for small-network routing
applications with the IP Base feature set. Limited static routing with the LAN Base feature set. Equal-cost
routing facilitates Layer 3 load balancing and redundancy across the stack.
●
Advanced IP unicast routing protocols (Open Shortest Path First [OSPF], EIGRP, Border Gateway Protocol
Version 4 [BGPv4], and Intermediate System-to-Intermediate System Version 4 [IS-ISv4]) are supported for
load balancing and constructing scalable LANs. IPv6 routing (OSPFv3, EIGRPv6) is supported in hardware
for maximum performance. OSPF for routed access is included in the IP Base image. The IP Services
feature set is required for full OSPF, EIGRP, BGPv4, and IS-ISv4.
●
Policy-based routing (PBR) allows superior control by facilitating flow redirection regardless of the routing
protocol configured. Virtual routing and forwarding (VRF)-Lite enables a service provider to support two or
more VPNs, with overlapping IP addresses. The IP Services feature set is required.
●
Protocol-independent multicast (PIM) for IP multicast routing is supported, including PIM sparse mode
(PIM-SM), PIM dense mode (PIM-DM), PIM sparse-dense mode, and source-specific multicast (SSM).
The IP Services feature set is required.
●
IPv6 addressing is supported on interfaces with appropriate show commands for monitoring and
troubleshooting.
Superior QoS
The Cisco Catalyst 3850 Series offers Gigabit Ethernet speed with intelligent services that keep traffic flowing
smoothly, even at 10 times the normal network speed. Industry-leading mechanisms for cross-stack marking,
classification, and scheduling deliver superior performance for data, voice, and video traffic, all at wire speed.
The following are some of the QoS features supported in the Cisco Catalyst 3850 Series Switches:
●
Granular wireless bandwidth management and fair sharing use Cisco’s proven Cisco IOS Software and
UADP ASIC technology to provide hierarchical bandwidth management at line rate (per access point, per
radio, per SSID, per client-based policies). Fair sharing across the users within an SSID makes sure that no
single user is starved because of other heavy-hitting users. Fair sharing is automatically enabled for
wireless at user level as well as SSID level.
●
802.1p CoS and DSCP field classification is provided, using marking and reclassification on a per-packet
basis by source and destination IP address, MAC address, or Layer 4 Transmission Control Protocol/User
Datagram Protocol (TCP/UDP) port number.
●
Shaped round robin (SRR) scheduling helps ensure differential prioritization of packet flows by intelligently
servicing the ingress queues and egress queues. Weighted tail drop (WTD) provides congestion avoidance
at the ingress and egress queues before a disruption occurs. Strict priority queuing helps ensure that the
highest priority packets are serviced ahead of all other traffic.
●
The Cisco committed information rate (CIR) function provides bandwidth in increments as low as 8 Kbps.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 17 of 35
●
Rate limiting is provided based on source and destination IP address, source and destination MAC address,
Layer 4 TCP/UDP information, or any combination of these fields, using QoS ACLs (IP ACLs or MAC
ACLs), class maps, and policy maps.
●
Eight egress queues per port for wired traffic and four egress queues for wireless help enable differentiated
management of different traffic types across the stack for wired traffic. Up to 2000 aggregate policers are
available per switch.
Application Visibility and Control Using Flexible NetFlow
Cisco IOS Software FNF is the next generation in flow visibility technology, allowing optimization of the network
infrastructure, reducing operation costs, and improving capacity planning and security incident detection with
increased flexibility and scalability. The Cisco Catalyst 3850 provides optimized application visibility with FNF
across wired plus wireless. The switch is capable of up to 48,000 flow entries on 48-port models and up to 24,000
flow entries on 12-port and 24-port models across wired plus wireless. With UADP ASIC, Cisco Catalyst 3850
delivers next-generation flow technology with unprecedented flexibility and comprehensive visibility extending from
Layer 2 (MAC and VLAN) to Layer 4 (TCP/UDP) flags and so on across wired plus wireless traffic. The Cisco
Catalyst 3850 switch is Medianet capable to provide visibility and troubleshooting capabilities across wired plus
wireless video traffic. Specific Medianet features will be enabled in future software updates.
The flow data collected by FNF can be exported to an external collector for analysis and reporting or tracked by the
EEM. The Cisco Catalyst 3850 enables powerful on-box and customizable event correlation and policy actions with
EEM, allowing the switches to trigger customized event alarms or policy actions when the predefined condition is
met. With no external appliance required, customers are able to use existing infrastructure to perform traffic
monitoring, making traffic analysis economical even on a large IP network.
Details about Cisco FNF are available at
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6555/ps6601/ps6965/product_data_sheet0900aecd
804b590b.html.
High-performance video over wireless integrates Cisco VideoStream technology to optimize the delivery of video
applications across the WLAN.
Wired plus wireless IP telephony supports unified communications for improved collaboration through messaging,
presence, and conferencing and supports all Cisco Unified Communications wireless IP phones for cost-effective,
real-time voice service.
Deployment Options
Campus
In a campus-type deployment, operating the Cisco Catalyst 3850 in the mobility agent mode and centralizing the
mobility controller functionality in a WLC 5760, WLC 5508, or WiSM2 helps achieve better scalability and
performance. The Cisco Catalyst 3850 provides CAPWAP termination for access points, uniform policy
enforcement for wireless clients, better wireless bandwidth, and uniform Cisco IOS Software-based configuration
and monitoring for wired plus wireless features. The mobility controller provides central mobility, RRM, and
CleanAir coordination.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 18 of 35
Backward compatibility with traditional centralized wireless deployment mode on the WLC 5508, WiSM2, and WLC
5760 helps ensure that customers can migrate to the Cisco Catalyst 3850-based converged access approach in
phases, providing a continued controller for existing access points. This migration also provides investment
protection on the existing wireless controller infrastructure. A phased adoption of the new Cisco Catalyst 3850
helps ensure that migration to the converged access mode of wireless is seamless. Figure 9 shows a Cisco
Catalyst 3850 in the campus type deployment.
Figure 9.
Mobility Controller (MC) and Mobility Agent (MA)
Branch
The Cisco Catalyst 3850 is optimized for branch deployments when it operates in mobility controller mode. In this
mode, not only can the switch terminate CAPWAP tunnels from the access points and provide client connectivity, it
can also manage mobility within the branch. This eliminates the need for a local controller in every branch in
addition to the access-layer switches. Also, complete visibility into the wired plus wireless traffic means that the
WAN router can prioritize the right wired plus wireless traffic in and out of the branch. Figure 10 shows a Cisco
Catalyst 3850 in a branch access type deployment.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 19 of 35
Figure 10.
Deploying the Cisco Catalyst 3850 in the Branch Access
The new 12-port and 24-port SFP+ or SFP-based Cisco Catalyst 3850 models as well as the nonstackable 48-port
SFP+ model can also be used in the branch to aggregate traffic from smaller access switches through fiber links for
more secure and EMI-sensitive deployments (Figure 11).
Figure 11.
Deploying Mixed Copper and Fiber Connections with a Cisco Catalyst 3850 Stack in the Branch
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 20 of 35
Cisco Catalyst 3850 Series Specifications
Switch Performance
Table 9 shows Cisco Catalyst 3850 Series Switches performance specifications.
Table 9.
Cisco Catalyst 3850 Performance Specifications
Performance Numbers for All Switch Models
Switching capacity
176 Gbps on 48-port Gigabit Ethernet model
92 Gbps on 24-port Gigabit Ethernet model
68 Gbps on 12-port Gigabit Ethernet model
560 Gbps on 24-port Multigigabit Ethernet model
472 Gbps on 48-port Multigigabit Ethernet model
1280 Gbps on 48-port 10 Gigabit Ethernet SFP+ model
640 Gbps on 24-port 10 Gigabit Ethernet SFP+ model
320 Gbps on 12-port 10 Gigabit Ethernet SFP+ model
Stacking bandwidth
480 Gbps
Total number of MAC addresses
32,000
Total number of IPv4 routes (ARP plus learned routes)
24,000
FNF entries
48,000 flow on 48-port Gigabit Ethernet models
24,000 flows on 12-port and 24-port Gigabit Ethernet models
96,000 flows on 48-port 10 Gigabit Ethernet SFP+ model
48,000 flows on 24-port 10 Gigabit Ethernet SFP+ model
24,000 flows on 12-port 10 Gigabit Ethernet SFP+ model
DRAM
4 GB (8 GB on 48-port SFP+ model)
Flash
2 GB (4 GB on 12-port and 24-port SFP+ models, 8 GB on 48-port SFP+ model)
VLAN IDs
4,000
Total switched virtual interfaces (SVIs)
1,000
Jumbo frame
9198 bytes
Total routed ports per 3850 stack
208
Wireless
Number of access points per switch/stack
100
Number of wireless clients per switch/stack
2000
Total number of WLANs per switch
64
Wireless bandwidth per switch
Up to 40 Gbps on 48-port Gigabit Ethernet model
Up to 20 Gbps on 24-port Gigabit Ethernet model
Supported Aironet access point series
3600, 3500, 2600, 1600, 1260, 1140, 1040
Forwarding Rate of Switch Models (with 2 x 10 Gigabit + 2 x 1 Gigabit Ethernet uplinks for 12-Port and 24-Port Models and 4 x 10 Gigabit
Ethernet Uplinks for 48‑Port Models)
Model
Forwarding Rate
WS-C3850-12S
50.5 Mpps
WS-C3850-24T
68.4 Mpps
WS-C3850-24P
WS-C3850-24S
WS-C3850-48T
130.95 Mpps
WS-C3850-48P
WS-C3850-48F
WS-C3850-24XU
500 Mpps (80B packets)
WS-C3850-12X48U
460 Mpps (64B packets)
WS-C3850-12XS
227.28 Mpps
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 21 of 35
Performance Numbers for All Switch Models
WS-C3850-24XS
454.55 Mpps
WS-C3850-48XS
909 Mpps
Dimensions, Weight, Acoustic, Mean Time between Failure, and Environmental Range
Specifications for Cisco Catalyst 3850 Series Switches
Table 10 shows dimensions, weight, acoustic, mean time between failure (MTBF), and environmental range.
Weight does not include an uplink FRU. Weight includes the chassis assembly as it is shipped (with fans), one
power supply and, and one power supply slot blank.
Table 10.
Dimensions, Weight, Acoustic, MTBF, and Environmental Range
12
Dimensions (H x W x D)
Inches
Centimeters
WS-C3850-12S
1.75 x 17.5 x 17.7
4.45 x 44.5 x 45.0
1.75 x 17.5 x 19.2
4.45 x 44.5 x 48.8
1.75 x 17.5 x 17.7
4.45 X 44.5 x 45.0
WS-C3850-24S
WS-C3850-24T
WS-C3850-24P
WS-C3850-48T
WS-C3850-48P
WS-C3850-48F
WS-C3850-48U
WS-C3850-24U
WS-C3850-24XU
WS-C3850-12X48U
WS-C3850-12XS
WS-C3850-24XS
WS-C3850-48XS
1.75 x 17.5 x 20.1
4.45 X 44.5 x 51.1
Weight
Pounds
Kilograms
WS-C3850-12S
15.48
7.02
WS-C3850-24S
15.5
7.03
WS-C3850-24T
15.9
7.2
WS-C3850-24P
16.3
7.4
WS-C3850-24U
16.5
7.5
WS-C3850-48T
17.0
7.7
WS-C3850-48P
17.4
7.9
WS-C3850-48F
17.6
8.0
WS-C3850-48U
17.6
8.0
WS-C3850-24XU
17.6
8.0
WS-C3850-12X48U
17.6
8.0
WS-C3850-12XS
12.9
5.8
WS-C3850-24XS
13.5
6.1
WS-C3850-48XS
16.42
7.45
C3850-NM-4-1G
0.66
0.30
C3850-NM-2-10G
0.71
0.32
C3850-NM-4-10G
0.75
0.34
C3850-NM-8-10G
0.74
0.34
C3850-NM-2-40G
0.62
0.28
12
Additional information about the 48-port SFP+ model will be provided at time of shipment.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 22 of 35
MTBF Hours
WS-C3850-12S
315,840
WS-C3850-24S
300,760
WS-C3850-24T
303,230
WS-C3850-24P
269,450
WS-C3850-24U
237,310
WS-C3850-48T
303,660
WS-C3850-48P
241,050
WS-C3850-48F
241,050
WS-C3850-48U
205,110
WS-C3850-24XU
203,150
WS-C3850-12X48U
202,030
WS-C3850-12XS
371,440
WS-C3850-24XS
307,990
WS-C3850-48XS
286,900
PWR-C1-350WAC
580,710
PWR-C1-715WAC
664,055
PWR-C1-1100WAC
392,174
PWR-C1-440WDC
469,350
C3850-NM-4-1G
7,052,100
C3850-NM-2-10G
4,315,970
C3850-NM-4-10G
3,835,330
Environmental Ranges
With AC power supply
Operating environment and altitude
Normal operating temperature* and altitudes:
● -5ºC to +45ºC, up to 5000 feet (1500m)
● -5ºC to +40ºC, up to 10,000 feet (3000m)
*
Minimum ambient temperature for cold start is 32°F (0°C)
Short-term* exceptional conditions:
● -5ºC to +50ºC, up to 5000 feet (1500m)
● -5ºC to +45ºC, up to 10,000 feet (3000m)
● -5ºC to +45ºC, at sealevel with single fan failure
*
With DC power supply
Operating environment and altitude (NEBS)
Not more than following in one-year period: 96 consecutive hours, or 360 hours total, or 15
occurrences.
Normal operating temperature and altitudes:
● -5ºC to +45ºC, up to 6000 feet (1800m)
● -5ºC to +40ºC, up to 10,000 feet (3000m)
● -5ºC to +35ºC, up to 13,000 feet (4000m)
Short-term* exceptional conditions:
● -5ºC to +55ºC, up to 6000 feet (1800m)
● -5ºC to +50ºC, up to 10,000 feet (3000m)
● -5ºC to +45ºC, up to 13,000 feet (4000m)
● -5ºC to +45ºC, at sealevel with single fan failure
*
Not more than following in one-year period: 96 consecutive hours, or 360 hours total, or 15
occurrences.
Relative humidity
10% to 95%, noncondensing
Acoustic noise
With AC or DC power supply (with 24 PoE+ ports loaded):
● LpA: 43dB typical, 45dB maximum
Measured per ISO 7779 and declared per ISO
9296
Bystander positions operating to an ambient
temperature of 25°C
● LwA: 5.2B typical, 5.5B maximum
Typical: Noise emission for a typical configuration
Maximum: Statistical maximum to account for variation in production
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 23 of 35
Storage environment
Temperature: -40ºC to 70ºC
Altitude: 15,000 ft
Vibration
Operating: 0.41Grms from 3 to 500Hz with spectral break points of 0.0005 G2/Hz at 10Hz and
200Hz 5dB/octave roll off at each end.
Nonoperating: 1.12Grms from 3 to 500Hz with spectral break points of 0.0065 G2/Hz at 10Hz
and 100Hz 5dB/octave roll off at each end.
Shock
Operating: 30G, 2ms half sine
Nonoperating: 55G, 10ms trapezoid
Connectors for Cisco Catalyst 3850 Series
Table 11 shows the supported connectors.
Table 11.
Connectors
Connectors and cabling
● 1000BASE-T ports: RJ-45 connectors, 4-pair Cat-5E UTP cabling
● Multigig-T ports: RJ-45 connectors, 4-pair Cat-5E, Cat-6, Cat6A UTP cabling
● 1000BASE-T SFP-based ports: RJ-45 connectors, 4-pair Cat-5E UTP cabling
● 100BASE-FX, 1000BASE-SX, -LX/LH, -ZX, -BX10, DWDM and CWDM SFP transceivers: LC fiber connectors
(single-mode or multimode fiber)
● 10GBASE-SR, LR, LRM, ER, ZR, DWDM SFP+ transceivers: LC fiber connectors (single-mode or
multimode fiber)
● CX1 cable assemblies: SFP+ connector
● Cisco StackWise-480 stacking ports: copper-based Cisco StackWise cabling
● Cisco StackPower: Cisco proprietary power stacking cables
● Ethernet management port: RJ-45 connectors, 4-pair Cat-5 UTP cabling
● Management console port: RJ-45-to-DB9 cable for PC connections
Power connectors
● Customers can provide power to a switch by using either the internal power or StackPower from another
member in the power stack. The connectors are located at the back of the switch.
● Internal power supply connector: The internal power supply is an autoranging unit. The internal power supply
supports input voltages between 100 and 240VAC. Use the supplied AC power cord to connect the AC power
connector to an AC power outlet.
For the latest Cisco transceiver module compatibility information, refer to
http://www.cisco.com/c/en/us/support/interfaces-modules/transceiver-modules/products-device-support-tableslist.html.
Management and Standards Support for Cisco Catalyst 3850 Series Switches
Table 12 shows management and standards support for the Cisco Catalyst 3850 Series.
Table 12.
Management and Standards Support for the Cisco Catalyst 3850 Series
Description
Specification
Management
BRIDGE-MIB
CISCO-SNMP-TARGET-EXT-MIB
CISCO-AUTH-FRAMEWORK-MIB
CISCO-STACKMAKER-MIB
CISCO-BGP4-MIB, BGP4-MIB
CISCO-MEMORY-POOL-MIB
CISCO-BRIDGE-EXT-MIB
CISCO-STP-EXTENSIONS-MIB
CISCO-BULK-FILE-MIB
CISCO-SYSLOG-MIB
CISCO-CABLE-DIAG-MIB
CISCO-TCP-MIB
CISCO-CALLHOME-MIB
CISCO-UDLDP-MIB
CISCO-CEF-MIB
CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
CISCO-CIRCUIT-INTERFACE-MIB
CISCO-VLAN-MEMBERSHIP-MIB
CISCO-ENTITY-VENDORTYPE-OID-MIB
CISCO-VTP-MIB
CISCO-CONTEXT-MAPPING-MIB
EtherLike-MIB
CISCO-DEVICE-LOCATION-MIB
HC-RMON-MIB
CISCO-DHCP-SNOOPING-MIB
IEEE8021-PAE-MIB
CISCO-EIGRP-MIB
IEEE8023-LAG-MIB
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 24 of 35
Description
Specification
CISCO-EMBEDDED-EVENT-MGR-MIB
IF-MIB
CISCO-ENTITY-FRU-CONTROL-MIB
IGMP-MIB
CISCO-ENTITY-SENSOR-MIB
IGMP-STD-MIB
ENTITY-MIB
IP-FORWARD-MIB
CISCO-ERR-DISABLE-MIB
IP-MIB
CISCO-CONFIG-COPY-MIB
IPMROUTE-STD-MIB
CISCO-FLOW-MONITOR-MIB
LLDP-EXT-MED-MIB
CISCO-FTP-CLIENT-MIB
LLDP-MIB
CISCO-HSRP-EXT-MIB
NOTIFICATION-LOG-MIB
CISCO-HSRP-MIB
OLD-CISCO-MEMORY-MIB
CISCO-IETF-ISIS-MIB
CISCO-CDP-MIB
CISCO-IF-EXTENSION-MIB
POWER-ETHERNET-MIB
CISCO-IGMP-FILTER-MIB
RMON2-MIB
CISCO-CONFIG-MAN-MIB
RMON-MIB
CISCO-IP-CBR-METRICS-MIB
SNMP-COMMUNITY-MIB
CISCO-IPMROUTE-MIB
SNMP-FRAMEWORK-MIB
CISCO-IP-STAT-MIB
SNMP-MPD-MIB
CISCO-IP-URPF-MIB
SNMP-NOTIFICATION-MIB
CISCO-L2L3-INTERFACE-CONFIG-MIB
SNMP-PROXY-MIB
CISCO-LAG-MIB
SNMP-TARGET-MIB
CISCO-LICENSE-MGMT-MIB
SNMP-USM-MIB
CISCO-MAC-AUTH-BYPASS-MIB
SNMPv2-MIB
CISCO-MAC-NOTIFICATION-MIB
SNMP-VIEW-BASED-ACM-MIB
CISCO-MDI-METRICS-MIB
TCP-MIB
CISCO-FLASH-MIB
UDP-MIB
CISCO-OSPF-MIB
CISCO-IMAGE-MIB
CISCO-OSPF-TRAP-MIB
CISCO-STACKWISE-MIB
CISCO-PAE-MIB
AIRESPMACE-WIRELESS-MIB
CISCO-PAGP-MIB
CISCO-LWAPP-IDS-MIB
CISCO-PIM-MIB
CISCO-LWAPP-AP-MIB
CISCO-PING-MIB
CISCO-LWAPP-CCX-RM-MIB
CISCO-PORT-QOS-MIB
CISCO-LWAPP-CLIENT-ROAMING-MIB
CISCO-PORT-SECURITY-MIB
CISCO-LWAPP-DOT11-CCX-CLIENT-DIAG-MIB
CISCO-PORT-STORM-CONTROL-MIB
CISCO-LWAPP-DOT11-CCX-CLIENT-MIB
CISCO-POWER-ETHERNET-EXT-MIB
CISCO-PRIVATE-VLAN-MIB
CISCO-LWAPP-DOT11-CLIENT-CCX-REPORTSMIB
CISCO-PROCESS-MIB
CISCO-LWAPP-DOT11-CLIENT-MIB
CISCO-PRODUCTS-MIB
CISCO-LWAPP-DOT11-MIB
CISCO-RF-MIB
CISCO-LWAPP-DOWNLOAD-MIB
CISCO-RTP-METRICS-MIB
CISCO-LWAPP-LINKTEST-MIB
CISCO-RTTMON-MIB
CISCO-LWAPP-MFP-MIB
CISCO-SMART-INSTALL-MIB
CISCO-LWAPP-MOBILITY-EXT-MIB
CISCO-LWAPP-QOS-MIB
CISCO-LWAPP-REAP-MIB
CISCO-LWAPP-ROGUE-MIB
CISCO-LWAPP-RRM-MIB
CISCO-LWAPP-SI-MIB
CISCO-LWAPP-TSM-MIB
CISCO-LWAPP-WLAN-MIB
CISCO-LWAPP-WLAN-SECURITY-MIB
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 25 of 35
Description
Specification
Standards
IEEE 802.1s
RMON I and II standards
IEEE 802.1w
SNMPv1, SNMPv2c, and SNMPv3
IEEE 802.11
IEEE 802.1x
IEEE 802.1x-Rev
IEEE 802.3ad
IEEE 802.3af
IEEE 802.3at
IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and
1000BASE-T ports
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1p CoS prioritization
IEEE 802.1Q VLAN
IEEE 802.3 10BASE-T specification
IEEE 802.3u 100BASE-TX specification
IEEE 802.3ab 1000BASE-T specification
IEEE 802.3z 1000BASE-X specification
Power Supply Specifications
Table 13 lists the power specifications for the Cisco Catalyst 3850 Series based on the kind of power supply used.
Table 13.
Power Specifications for Cisco Catalyst 3850 Series
Description
Specification
PWR-C1-1100WAC
PWR-C1-715WAC
PWR-C1-350WAC
PWR-C1-440WDC
Power supply rated maximum
1100W
715W
350W
440W
Total output BTU (Note: 1000 BTU/hr
= 293W)
3793 BTU/hr, 1100W
2465 BTU/hr, 715W
1207BTU/hr, 350W
1517BTU/hr, 440W
Input-voltage range and frequency
115-240VAC,
100-240VAC,
100-240VAC,
-36VDC to -72VDC
50-60 Hz
50-60 Hz
50-60 Hz
12-6A
10-5A
4-2A
Input current
<8A at -72VDC
<16A at -36VDC
Output ratings
-56V at 19.64A
-56V at 12.8A
-56V at 6.25A
-56V at 7.86A
Output holdup time
10 ms minimum at
102.5VAC
16.7 ms minimum at
100VAC
16.7 ms minimum at
100VAC
> 2ms at -48VDC
Power-supply input receptacles
IEC 320-C16
IEC 320-C16
(IEC60320-C16)
IEC 320-C16
(IEC60320-C16)
Terminal strip
(IEC60320-C16)
Power cord rating
13A
13A
10A
20A at 100VDC
Physical specifications
(H x W x D): 1.58 X
3.25 X 13.7 in
(H x W x D): 1.58 X
3.25 X 12.20 in
(H x W x D): 1.58 X 3.25
X 12.20 in
(H x W x D): 1.58 X 3.25
X 12.20 in
Weight: 3 lb
(1.4 kg)
Weight: 2.8 lb
(1.3 kg)
Weight: 2.6 lb
(1.2 kg)
Weight: 2.6 lb
(1.2 kg)
Operating temperature
23 to 113°F (-5 to 45°C)
Storage temperature
-40 to 158°F (-40 to 70°C)
Relative humidity operating and
nonoperating noncondensing
5 to 90% noncondensing
Altitude
10,000 ft. (3000 meters), up to 45°C
MTBF
Calculated MTBF must be greater than 300,000 using Telcordia SR-332, Method 1, Case 3.
Demonstrated MTBF is 500,000 hr (with 90% confidence level).
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 26 of 35
Description
Specification
EMI and EMC compliance
FCC Part 15 (CFR 47) Class A
ICES-003 Class A
EN 55022 Class A
CISPR 22 Class A
AS/NZS 3548 Class A
BSMI Class A (AC input models only)
VCCI Class A
EN 55024, EN300386, EN 50082-1, EN 61000-3-2, EN 61000-3-3
EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN 61000-6-1
Safety compliance
UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, CCC, CE Marking
LED indicators
“AC OK”: Input power to the power supply is OK
“PS OK”: Output power from the power supply is OK
Power Consumption of Standalone Cisco Catalyst 3850 Series Switches
Table 14 shows power consumption of standalone Cisco Catalyst 3850 Series Switches based on Alliance for
Telecommunications Industry Solutions (ATIS) testing using IMIX distribution stream traffic, with input voltage of
115VAC at 60 Hz and no PoE loading. The values given are the maximum possible power consumption numbers
under the respective test scenarios.
Table 14.
Power Consumptions (in Watts) of Standalone Cisco Catalyst 3850 Series
Models
Uplink Module
Power Consumption (W) (No More Than)
0% Traffic
10% Traffic
100% Traffic
Weighted Average
85.84
85.89
86.75
86.0
104.48
104.25
105.12
104.4
87.95
88.30
90.04
88.4
106.24
106.58
109.75
106.9
83.47
82.86
83.76
83.04
WS-C3850-24P
86.81
86.22
87.11
86.40
WS-C3850-24U
81.5
81.4
82.1
81.5
WS-C3850-48T
117.74
116.62
117.59
116.89
WS-C3850-48P
125.35
124.15
125.15
124.43
WS-C3850-48F
130.10
128.91
129.85
129.18
114.8
114.7
115.6
114.8
81.97
81.83
84.97
82.16
WS-C3850-24P
85.22
85.04
88.32
85.39
WS-C3850-24U
82.8
82.6
84.8
82.9
WS-C3850-48T
117.56
116.74
120.40
117.23
WS-C3850-48P
123.78
122.90
126.75
123.42
WS-C3850-48F
129.89
129.06
132.36
129.18
116.8
116.9
119.9
117.2
120.56
120.28
127.24
121.02
WS-C3850-48P
129.59
129.64
135.96
130.27
WS-C3850-48F
137.57
137.06
143.77
137.81
WS-C3850-48U
119.9
121.2
127.7
121.5
WS-C3850-12XS
109.0
109.5
112.7
109.7
WS-C3850-12S
C3850-NM-4-1G
WS-C3850-24S
WS-C3850-12S
C3850-NM-2-10G
WS-C3850-24S
WS-C3850-24T
C3850-NM-4-1G
WS-C3850-48U
WS-C3850-24T
C3850-NM-2-10G
WS-C3850-48U
WS-C3850-48T
C3850-NM-4-10G
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 27 of 35
Models
Uplink Module
WS-C3850-24XU
C3850-NM-8-10G
Power Consumption (W) (No More Than)
0% Traffic
10% Traffic
100% Traffic
Weighted Average
229.7
231.2
248.1
232.7
WS-C3850-12X48U
191.3
193.6
208.1
194.8
WS-C3850-24XS
183.6
185.3
205.5
187.2
WS-C3850-24XS
C3850-NM-2-40G
159.2
161.1
177.0
162.5
WS-C3850-48XS
None
267.0
268.3
288.1
270.1
Safety and Compliance
Table 15 lists the safety and compliance information for the Cisco Catalyst 3850 Series.
Table 15.
Safety and Compliance Information for Cisco Catalyst 3850 Series
Description
Specification
Safety certifications
UL 60950-1 Second Edition
CAN/CSA-C22.2 No. 60950-1 Second Edition
EN 60950-1 Second Edition
IEC 60950-1 Second Edition
NOM (obtained by partners and distributors)
Electromagnetic emissions
certifications
47CFR Part 15 (CFR 47) Class A (FCC Part 15 Class A)
AS/NZS CISPR22 Class A
CISPR22 Class A
EN55022 Class A
ICES003 Class A
VCCI Class A
EN61000-3-2
EN61000-3-3
KN22 Class A
KCC
CNS13438 Class A
EN55024
CISPR24
KN24
Environmental
Reduction of Hazardous Substances (ROHS) 5
Noise specifications
Office Product Spec: 48dBA at 30°C (refer to ISO 7779)
Telco
CLEI code
Cisco Enhanced Limited Lifetime Hardware Warranty
The Cisco Catalyst 3850 Series Switches come with an E-LLW that includes NBD delivery of replacement
hardware where available and 90 days of 8x5 Cisco TAC support.
Your formal warranty statement, including the warranty applicable to Cisco software, appears in the Cisco
information packet that accompanies your Cisco product. We encourage you to review carefully the warranty
statement shipped with your specific product before use.
Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.
For further information about warranty terms, visit http://www.cisco.com/go/warranty. Table 16 provides information
about the E-LLW.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 28 of 35
Table 16.
E-LLW Details
Cisco E-LLW
Device covered
Applies to Cisco Catalyst 3850 Series Switches.
Warranty duration
As long as the original customer owns the product.
EoL policy
In the event of discontinuance of product manufacture, Cisco warranty support is limited to 5 years from the
announcement of discontinuance.
Hardware replacement
Cisco or its service center will use commercially reasonable efforts to ship a replacement for NBD delivery, where
available. Otherwise, a replacement will be shipped within 10 working days after receipt of the RMA request. Actual
delivery times might vary depending on customer location.
Effective date
Hardware warranty commences from the date of shipment to customer (and in case of resale by a Cisco reseller, not
more than 90 days after original shipment by Cisco).
TAC support
Cisco will provide during business hours, 8 hours per day, 5 days per week basic configuration, diagnosis, and
troubleshooting of device-level problems for up to a 90-day period from the date of shipment of the originally
purchased Cisco Catalyst 3850 product. This support does not include solution or network-level support beyond the
specific device under consideration.
Cisco.com access
Warranty allows guest access only to Cisco.com.
Licensing for Cisco Catalyst 3850 Series Switches
The three feature sets available with all Cisco Catalyst 3850 Series Switches are:
●
LAN Base: Enterprise access layer 2 switching features
●
IP Base: Enterprise access layer 3 switching features
●
IP Services: Advanced enterprise layer 3 switching (IPv4 and IPv6) features
The LAN Base feature set offers enhanced intelligent services that include comprehensive Layer 2 features, with
up to 255 VLANs. The IP Base feature set provides entry-level enterprise services in addition to all LAN Base
features, with 1K VLANs. IP Base also includes the support for wireless controller functionality (mobility agent and
mobility controller role; additional access point license required for mobility controller role), routed access, smart
operations, FNF, and so on. The IP Services feature set provides full enterprise services that include advanced
Layer 3 features such as EIGRP, OSPF, BGP, PIM, and IPv6 routing such as OSPFv3 and EIGRPv6. All software
feature sets support advanced security and MQC-based QoS.
The Cisco Catalyst 3850 Series Switches with LAN Base feature set can only stack with other Cisco Catalyst 3850
Series LAN Base switches. The same applies to IP Base and IP Services as well. A mixed stack of LAN Base
switch with IP Base or IP Services feature set is not supported.
The 12-port and 24-port SFP+- and SFP-based models as well as the 48-port SFP+ model can only be ordered
with IP Base or IP Services licenses. Therefore, in order to stack with LAN Base models, they need to be
configured in LAN Base mode from the CLI.
Customers can transparently upgrade the software feature set in the Cisco Catalyst 3850 Series Switches through
Cisco IOS Software CLI using the right to use (RTU)-based software upgrade process. Software activation enables
the Cisco IOS Software feature sets. Based on the license’s type, Cisco IOS Software activates the appropriate
feature set. License types can be changed, or upgraded, to activate a different feature set.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 29 of 35
Access Point License for Cisco Catalyst 3850
An access point license is required for Cisco Catalyst 3850 operating in mobility controller mode. No access point
license is required for 3850 operating in mobility agent mode. This functionality is included in the IP Base feature
set. Other devices that can act as mobility controller are the WLC 5760, WLC 5508, and WiSM2 wireless
controllers. Access point licenses can be transferred only between two 3850 switches or between 3850 and 5760
controller and vice versa.
Software Policy for Cisco Catalyst 3850 Series Switches
Customers with Cisco Catalyst LAN Base and IP Base software feature sets will be provided with maintenance
updates and bug fixes designed to maintain the compliance of the software with published specifications, release
notes, and industry standards compliance as long as the original end user continues to own or use the product or
up to one year from the end-of-sale date for this product, whichever occurs earlier. Customers with licenses for our
IP Services software images require a service support contract such as Cisco SMARTnet® Service to download
updates. This policy supersedes any previous warranty or software statement and is subject to change without
notice.
Cisco and Partner Services for Next-Generation Cisco Catalyst Fixed Switches
Enable the innovative, secure, intelligent edge in the Borderless Network Architecture using personalized services
from Cisco and our partners. Through a discovery process that begins with understanding your business
objectives, we help you integrate the next-generation Cisco Catalyst fixed switches into your architecture and
incorporate network services onto that platform. Sharing knowledge and leading practices, we support your
success every step of the way as you deploy, absorb, manage, and scale new technology. Choose from a flexible
suite of support services designed to meet your business needs and help you maintain high-quality network
performance while controlling operational costs. (See Table 17.)
Table 17.
Technical Services Available for Cisco Catalyst 3850 Switches
Technical Services
Cisco SMARTnet Service
●
●
●
●
●
Around-the-clock, global access to the Cisco TAC
Unrestricted access to the extensive Cisco.com knowledge base and tools
Next-business-day, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement and onsite parts replacement and installation available
Ongoing operating system software updates within the licensed feature set
Proactive diagnostics and real-time alerts on Smart Call Home-enabled devices
Cisco Smart Foundation Service
●
●
●
●
●
NBD advance hardware replacement as available
Business hours access to SMB TAC (access levels vary by region)
Access to Cisco.com SMB knowledge base
Online technical resources through Smart Foundation Portal
Operating system software bug fixes and patches
Cisco SP Base Service
●
●
●
●
Around-the-clock, global access to the Cisco TAC
Registered access to Cisco.com
NBD, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement; return to factory option available2
Ongoing operating system software updates1
Cisco Focused Technical Support Services
● Three levels of premium, high-touch services are available:
◦ Cisco High-Touch Operations Management Service
◦ Cisco High-Touch Technical Support Service
◦ Cisco High-Touch Engineering Service
● Valid Cisco SMARTnet or SP Base contracts on all network equipment are required
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 30 of 35
Notes:
1
Cisco operating system updates include the following: maintenance releases, minor updates, and major updates within the
licensed feature set.
2
Advance hardware replacement is available in various service-level combinations. For example, 8x5xNBD indicates that
shipment will be initiated during the standard 8-hour business day, 5 days a week (the generally accepted business days within
the relevant region), with NBD delivery. Where NBD is not available, same day ship is provided. Restrictions apply; for details,
review the appropriate service descriptions.
Ordering Information
Table 18 lists ordering information for the Cisco Catalyst 3850 Series. To place an order, visit the Cisco Ordering
homepage at http://www.cisco.com/en/US/ordering/or13/or8/order_customer_help_how_to_order_listing.html.
Table 18.
Cisco Catalyst 3850 Series Ordering Information
Product Number
Product Description
Cisco Catalyst 3850 Series
WS-C3850-24T-L
Stackable 24 10/100/1000 Ethernet ports, with 350WAC power supply
1 RU, LAN Base feature set (StackPower cables need to be purchased separately)
WS-C3850-48T-L
Stackable 48 10/100/1000 Ethernet ports, with 350WAC power supply
1 RU, LAN Base feature set (StackPower cables need to be purchased separately)
WS-C3850-24P-L
Stackable 24 10/100/1000 Ethernet PoE+ ports, with 715WAC power supply
1 RU, LAN Base feature set (StackPower cables need to be purchased separately)
WS-C3850-24U-L
Stackable 24 10/100/1000 Ethernet UPOE ports, with 1100WAC power supply
1 RU, LAN Base feature set (StackPower cables need to be purchased separately)
WS-C3850-48P-L
Stackable 48 10/100/1000 Ethernet PoE+ ports, with 715WAC power supply
1 RU, LAN Base feature set (StackPower cables need to be purchased separately)
WS-C3850-48F-L
Stackable 48 10/100/1000 Ethernet PoE+ ports, with 1100WAC power supply
1 RU, LAN Base feature set (StackPower cables need to be purchased separately)
WS-C3850-48U-L
Stackable 48 10/100/1000 Ethernet UPOE ports, with 1100WAC power supply
1 RU, LAN Base feature set (StackPower cables need to be purchased separately)
WS-C3850-24T-S
Stackable 24 10/100/1000 Ethernet ports, with 350WAC power supply
1 RU, IP Base feature set
WS-C3850-48T-S
Stackable 48 10/100/1000 Ethernet ports, with 350WAC power supply
1 RU, IP Base feature set
WS-C3850-24P-S
Stackable 24 10/100/1000 Ethernet PoE+ ports, with 715WAC power supply
1 RU, IP Base feature set
WS-C3850-24U-S
Stackable 24 10/100/1000 Ethernet UPOE ports, with 1100WAC power supply
1 RU, IP Base feature set
WS-C3850-48P-S
Stackable 48 10/100/1000 Ethernet PoE+ ports, with 715WAC power supply
1 RU, IP Base feature set
WS-C3850-48F-S
Stackable 48 10/100/1000 Ethernet PoE+ ports, with 1100WAC power supply
1 RU, IP Base feature set
WS-C3850-48U-S
Stackable 48 10/100/1000 Ethernet UPOE ports, with 1100WAC power supply
1 RU, IP Base feature set
WS-C3850-24T-E
Stackable 24 10/100/1000 Ethernet ports, with 350WAC power supply
1 RU, IP Services feature set
WS-C3850-48T-E
Stackable 48 10/100/1000 Ethernet ports, with 350WAC power supply
1 RU, IP Services feature set
WS-C3850-24P-E
Stackable 24 10/100/1000 Ethernet PoE+ ports, with 715WAC power supply
1 RU, IP Services feature set
WS-C3850-24U-E
Stackable 24 10/100/1000 Ethernet UPOE ports, with 1100WAC power supply
1 RU, IP Services feature set
WS-C3850-48P-E
Stackable 48 10/100/1000 Ethernet PoE+ ports, with 715WAC power supply
1 RU, IP Services feature set
WS-C3850-48F-E
Stackable 48 10/100/1000 Ethernet PoE+ ports, with 1100WAC power supply
1 RU, IP Services feature set
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 31 of 35
Product Number
Product Description
WS-C3850-48U-E
Stackable 48 10/100/1000 Ethernet UPOE ports, with 1100WAC power supply
1 RU, IP Services feature set
WS-C3850-12X48U-L
Stackable 48 10/100/1000 with 12 100Mbps/1/2.5/5/10 Gbps UPOE Ethernet ports, with 1100W AC power supply
1RU, LAN Base feature set
WS-C3850-12X48U-S
Stackable 48 10/100/1000 with 12 100Mbps/1/2.5/5/10 Gbps UPOE Ethernet ports, with 1100W AC power supply
1RU, IP Base feature set
WS-C3850-12X48U-E
Stackable 48 10/100/1000 with 12 100Mbps/1/2.5/5/10 Gbps UPOE Ethernet ports, with 1100W AC power supply
1RU, IP Services feature set
WS-C3850-24XU-L
Stackable 24 100Mbps/1/2.5/5/10 Gbps UPOE Ethernet ports, with 1100W AC power supply
1RU, LAN Base feature set
WS-C3850-24XU-S
Stackable 24 100Mbps/1/2.5/5/10 Gbps UPOE Ethernet ports, with 1100W AC power supply
1RU, IP Base feature set
WS-C3850-24XU-E
Stackable 24 100Mbps/1/2.5/5/10 Gbps UPOE Ethernet ports, with 1100W AC power supply
1RU, IP Services feature set
WS-C3850-12S-S
Stackable 12 SFP Ethernet ports, with 350WAC power supply
1 RU, IP Base feature set
WS-C3850-12S-E
Stackable 12 SFP Ethernet ports, with 350WAC power supply
1 RU, IP Services feature set
WS-C3850-24S-S
Stackable 24 SFP Ethernet ports, with 350WAC power supply
1 RU, IP Base feature set
WS-C3850-24S-E
Stackable 24 SFP Ethernet ports, with 350WAC power supply
1 RU, IP Services feature set
WS-C3850-12XS-S
Stackable 12 SFP+ Ethernet ports, with 350WAC power supply
1 RU, IP Base feature set
WS-C3850-12XS-E
Stackable 12 SFP+ Ethernet ports, with 350WAC power supply
1 RU, IP Services feature set
WS-C3850-24XS-S
Stackable 24 SFP+ Ethernet ports, with 715WAC power supply
1 RU, IP Base feature set
WS-C3850-24XS-E
Stackable 24 SFP+ Ethernet ports, with 715WAC power supply
1 RU, IP Services feature set
WS-C3850-48XS-S
Standalone, 48 SFP+ and 4 QSFP+ Ethernet ports, with 750WAC front-to-back power supply
1 RU, IP Base feature set
WS-C3850-48XS-E
Standalone, 48 SFP+ and 4 QSFP+ Ethernet ports, with 750WAC front-to-back power supply
1 RU, IP Services feature set
WS-C3850-48XS-F-S
Standalone, 48 SFP+ and 4 QSFP+ Ethernet ports, with 750WAC back-to-front power supply
1 RU, IP Base feature set
WS-C3850-48XS-F-E
Standalone, 48 SFP+ and 4 QSFP+ Ethernet ports, with 750WAC back-to-front power supply
1 RU, IP Services feature set
Cisco Catalyst 3850 Bundles
WS-C3850-24PW-S
Cisco Catalyst 3850 24-port PoE IP Base with 5 access point license
WS-C3850-48PW-S
Cisco Catalyst 3850 48-port PoE IP Base with 5 access point license
WS-C3850-24UW-S
Cisco Catalyst 3850 24 Port UPOE with 5 access point licenses IP Base
WS-C3850-48W-S
Cisco Catalyst 3850 48 Port PoE with 5 access point licenses IP Base
WS-C3850-48UW-S
Cisco Catalyst 3850 48 Port UPOE with 5 access point licenses IP Base
WS-C3850-24XUW-S
Cisco Catalyst 3850 24 Port UPOE with 24 100Mbps/1/2.5/5/10 Gbps and 5 access point licenses IP Base
WS-C3850-12X48UW-S
Cisco Catalyst 3850 48 Port UPOE with 12 100Mbps/1/2.5/5/10 Gbps and 5 access point licenses IP Base
WS-C3850-16XS-S
Cisco Catalyst 3850 12 SFP+ port stackable model, with C3850-NM-4-10G module and 350WAC power supply.
1 RU, IP Base feature set
WS-C3850-16XS-E
Cisco Catalyst 3850 12 SFP+ port stackable model, with C3850-NM-4-10G module and 350WAC power supply.
1 RU, IP Services feature set
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 32 of 35
Product Number
Product Description
WS-C3850-32XS-S
Cisco Catalyst 3850 24 SFP+ port stackable model, with C3850-NM-8-10G module and 715WAC power supply. 1
RU, IP Base feature set
WS-C3850-32XS-E
Cisco Catalyst 3850 24 SFP+ port stackable model, with C3850-NM-8-10G module and 715WAC power supply. 1
RU, IP Services feature set
Network Modules for the Cisco Catalyst 3850 Series
C3850-NM-4-1G=
4 x Gigabit Ethernet network module spare
C3850-NM-2-10G=
4 x Gigabit Ethernet/2 x 10 Gigabit Ethernet network module spare
C3850-NM-BLANK=
Network module blank spare
C3850-NM-4-10G=
4 x Gigabit Ethernet/4 x 10 Gigabit Ethernet network module spare
C3850-NM-8-10G=
8 x Gigabit Ethernet/8 x 10 Gigabit Ethernet network module spare
C3850-NM-2-40G=
2 x 40 Gigabit Ethernet network module spare
Software Licenses
C3850-12-S-E
Cisco Catalyst 3850 12-port IP Base to IP Services RTU paper license
C3850-24-L-S
Cisco Catalyst 3850 24-port Switch LAN Base to IP Base RTU paper license
C3850-48-L-S
Cisco Catalyst 3850 48-port Switch LAN Base to IP Base RTU paper license
C3850-24-L-E
Cisco Catalyst 3850 24-port LAN Base to IP Services RTU paper license
C3850-48-L-E
Cisco Catalyst 3850 48-port LAN Base to IP Services RTU paper license
C3850-24-S-E
Cisco Catalyst 3850 24-port IP Base to IP Services RTU paper license
C3850-48-S-E
Cisco Catalyst 3850 48-port IP Base to IP Services RTU paper license
L-C3850-24-L-S
Cisco Catalyst 3850 24-port LAN Base to IP Base RTU electronic license
L-C3850-48-L-S
Cisco Catalyst 3850 48-port LAN Base to IP Base RTU electronic license
L-C3850-24-L-E
Cisco Catalyst 3850 24-port LAN Base to IP Services RTU electronic license
L-C3850-48-L-E
Cisco Catalyst 3850 48-port LAN Base to IP Services RTU electronic license
L-C3850-24-S-E
Cisco Catalyst 3850 24-port IP Base to IP Services RTU electronic license
L-C3850-48-S-E
Cisco Catalyst 3850 48-port IP Base to IP Services RTU electronic license
L-C3850-12-S-E
Cisco Catalyst 3850 12-port IP Base to IP Services RTU electronic license
Access Point Licenses
L-LIC-CT3850-UPG
Primary upgrade license SKU for Cisco 3850 wireless controller (e-delivery)
L-LIC-CTIOS-1A
1 access point adder license for Cisco IOS Software based wireless controller (e-delivery)
LIC-CT3850-UPG
Primary upgrade license SKU for Cisco 3850 wireless controller (paper license)
LIC-CTIOS-1A
1 access point adder license for the Cisco IOS Software based wireless controller (paper license)
Power Supplies and Fan for the Cisco Catalyst 3850 Series
PWR-C1-350WAC=
350WAC power supply spare
PWR-C1-715WAC=
715WAC power supply spare
PWR-C1-1100WAC=
1100WAC power supply spare
PWR-C1-440WDC=
440WDC power supply spare
PWR-C1-BLANK=
Power supply blank spare
PWR-C3-750WAC-R=
750WAC power supply spare front-to-back airflow for 48XS
PWR-C3-750WAC-F=
750WAC power supply spare back-to-front airflow for 48XS
PWR-C3-750WDC-R=
750WDC power supply spare front-to-back airflow for 48XS
PWR-C3-750WDC-F=
750WDC power supply spare back-to-front airflow for 48XS
FAN-T3-R=
Fan module spare front-to-back airflow for 48XS
FAN-T3-F=
Fan module spare back-to-front airflow for 48XS
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 33 of 35
Product Number
Product Description
StackWise-480 and StackPower Cables for the Cisco Catalyst 3850 Series
STACK-T1-50CM=
Cisco StackWise-480 50cm stacking cable spare
STACK-T1-1M=
Cisco StackWise-480 1m stacking cable spare
STACK-T1-3M=
Cisco StackWise-480 3m stacking cable spare
CAB-SPWR-30CM=
Cisco Catalyst 3850 StackPower cable 30cm spare
CAB-SPWR-150CM=
Cisco Catalyst 3850 StackPower cable 150cm spare
Spare Power Cords for the Cisco Catalyst 3850 Series
CAB-TA-NA=
AC power cord for Cisco Catalyst 3850 (North America)
CAB-TA-AP=
AC power cord for Cisco Catalyst 3850 (Australia)
CAB-TA-AR=
AC power cord for Cisco Catalyst 3850 (Argentina)
CAB-TA-SW=
AC power cord for Cisco Catalyst 3850 (Switzerland)
CAB-TA-UK=
AC power cord for Cisco Catalyst 3850 (United Kingdom)
CAB-TA-JP=
AC power cord for Cisco Catalyst 3850 (Japan)
CAB-TA-250VAC-JP=
Japan 250VAC power cord for Cisco Catalyst 3850 (Japan)
CAB-TA-EU=
AC power cord for Cisco Catalyst 3850 (Europe)
CAB-TA-IT=
AC power cord for Cisco Catalyst 3850 (Italy)
CAB-TA-IN=
AC power cord for Cisco Catalyst 3850 (India)
CAB-TA-CN=
AC power cord for Cisco Catalyst 3850 (China)
CAB-TA-DN=
AC power cord for Cisco Catalyst 3850 (Denmark)
CAB-TA-IS=
AC power cord for Cisco Catalyst 3850 (Israel)
CAB-ACBZ-12A=
AC power cord for Cisco Catalyst 3850 (Brazil), 12A/125V BR-3-20 plug up to 12A
CAB-ACBZ-10A=
AC power cord for Cisco Catalyst 3850 (Brazil), 10A/250V BR-3-10 plug up to 10A
CAB-C15-CBN
Cabinet jumper power cord, 250 VAC 13A, C14-C15 connectors
Spare Accessory and Rack Mount Kits for the Cisco Catalyst 3850 Series
C3850-ACC-KIT=
Accessory kit for Cisco Catalyst 3850 Series
C3850-RAC-KIT=
Rack mount kit for Cisco Catalyst 3850 Series
C3850-4PT-KIT=
Extension rails and brackets for four-point mounting for Cisco Catalyst 3850 Series
Optics Compatibility Information
The Cisco Catalyst 3850 Series supports a wide range of optics. Because the list of supported optics is updated on
a regular basis, consult the tables available here for the latest QSFP+, SFP+, and SFP compatibility information:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html.
Cisco Capital
Financing to Help You Achieve Your Objectives
Cisco Capital can help you acquire the technology you need to achieve your objectives and stay competitive. We
can help you reduce CapEx. Accelerate your growth. Optimize your investment dollars and ROI. Cisco Capital
financing gives you flexibility in acquiring hardware, software, services, and complementary third-party equipment.
And there’s just one predictable payment. Cisco Capital is available in more than 100 countries. Learn more.
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
Page 34 of 35
Printed in USA
© 2015 Cisco and/or its affiliates. This document is Cisco Public Information.
C78-720918-12
09/15
Page 35 of 35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising