Mobius_TB2_6panel copy

Mobius_TB2_6panel copy
(7) Formatting
(11) Troubleshooting and FAQ
After installing new drives, you must format the volumes before
they are accessible.
1) The unit does not power up.
The Thunderbolt cable must be connected in order for the Mobius
to power up. Also, make sure that the computer’s port is a
Thunderbolt port. Older Macs (2011 and earlier) include a
Mini DisplayPort, which uses the same connector but is not capable
of Thunderbolt technology.
To format using MAC OS:
http://oyendigital.com/mac-reformat.html
To format using Windows:
http://oyendigital.com/windows-reformat.html
Note: The drive can be used on both Windows and Mac
systems by formatting the drive as “MS-DOS (FAT32)” or
“exFAT.” Instructions are provided in the Mac OS link above.
(8) Sleep
If there is no HDD activity, the computer may put the Mobius to
sleep (LEDs off, HDDs spin down) depending on the energy saver
settings of the computer. The Mobius will wake up when
accessed.
(9) Ejecting the Drives
2) Which drives are recommended for use with the Mobius?
Any 2.5-inch or 3.5-inch SATA drive is compatible. However, for best
performance, we recommend using enterprise or NAS drives such as
WD Red, WD SE/RE.
3) I do not see the hard drives.
Briefly press (do not hold) the HDD power button for the corresponding
drive to remount the drive. If it is still not mounting, connect the
Mobius directly to a Thunderbolt port on the computer and disconnect
any other Thunderbolt devices. Then open Disk Utility (Applications >
Utilities > Disk Utility) to see if the drives are listed.
4) How do I configure a RAID?
The Mobius Thunderbolt does not include a hardware RAID controller.
However, it is compatible with software RAID applications such as
SoftRAID.
Mobius 5-Bay Thunderbolt 2
User Guide
To prevent potential data corruption, it is important to properly eject
the storage volume(s).
Mac: Close all windows and applications that are accessing the
drive. Drag the drive icon to the Trash/Eject icon to dismount it.
The activity LED will cycle on/off and the HDD will spin down.
Windows: Close all applications that are accessing the Mobius.
Click the “Eject Hardware” (Safely Remove) icon in the system tray
and select the drive. The activity LED will cycle on/off and the drive
will spin down.
(10) Warranty Information
This product includes a two (2) year repair/replacement warranty
provided by Oyen Digital. This warranty is non-transferable and is
limited to the original purchaser. Note: The warranty is 3 years if the
Mobius is purchased with hard drives installed by Oyen Digital.
Warranty service may be requested by completing the form at the
following link: www.oyendigital.com/rma-request-form.html
For our complete warranty policy, visit:
www.oyendigital.com/warranty.html
(12) Safety and Compliance
Location and placing precautions
• Avoid positioning it in locations with direct sunlight or other sources
of heat with high temperatures (over 120° F).
• Do not expose the product to water or humid conditions.
• Do not move the device while it is powered on.
• Do not operate the device in any position other than the upright position.
• Ensure that the device is on a clean, firm, and stable surface.
• To allow proper ventilation, do not block or disable the fan.
Table of Contents
1
Specifications
2
Detailed View
3
Installing Hard Drives
Electricity and power adapter
When removing the power cable from the socket, always pull on the
plug fixture and never on the cable.
4
Connecting to a Computer
5
HDD Power Button
6
Door Lock
Regulatory Compliance
FCC Class B Information: This device has been tested and found
to comply with the limits of a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This unit generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no
guarantee that interference will not occur in a particular
installation.
7
Formatting
8
Sleep
9
Ejecting the Drives
10
Warranty Information
11
Troubleshooting and FAQ
12
Safety and Compliance
For more information, visit our website at www.oyendigital.com
or contact us at 1-866-768-0659.
(1) Specifications
Supported Drives
(3) Installing Hard Drives
2.5” or 3.5” SATA I/II/III HDD/SSD
2 x Thunderbolt 2 Ports
Installing: Place a drive into a tray and slide onto the SATA connector.
Attach the drive to the tray using the included mounting screws.
Win 8 or higher; Mac OS 10.9 or higher
8.5 x 4.6 x 6.8 inches
Dimensions
Includes: Mobius 5-Bay Thunderbolt, power supply,
Thunderbolt cable, screw pack (3.5” & 2.5”), key set
(4) Connecting to a Computer
1. Connect the power adapter to the DC-IN input on the Mobius.
2. Connect the Thunderbolt cable to either port on the Mobius.
3. Connect the other end of the cable to the computer. Note: The
Thunderbolt cable must be connected for the unit to power up.
4. (Optional) Connect additional Thunderbolt devices as shown.
Up to 6 devices can be connected in a chain.
5. Turn on the power switch.
6. The Mobius powers up and the drives will mount to your computer.
(2) Detailed View
1
Bottom Tray View:
3.5-inch mounting holes (may vary based on drive model)
2.5-inch mounting holes (3 holes total)
2
4
1. Door Lock
2. Drive Trays
3. HDD Power Buttons
4. Power LED (top)
Activity LED (bottom)
3
LEDs:
7
Condition
LED
Powered & Thunderbolt Link Established
Read/Write activity
HDD Sleep
Power LED (top) - Solid white
Activity LED (bottom) - Blinking blue
Both LEDs - Off
Note: The LEDs will be OFF when the unit is not connected to a computer.
To insert or remove the tray: Slide the door latch (A) to the left to
release the door lever (B). Gently slide the tray in or out of the bay.
Note: The door lever (B) must be open when removing or inserting
the drive tray.
(5) HDD Power Button
The Mobius includes a button for each bay that allows a drive to be
powered off independently without having to turn off the entire unit.
Power off: Press and hold the corresponding button for 3-5 seconds.
The LEDs will turn off and the drive will spin down.
Power on: Briefly press the corresponding button (do not hold).
6
6. Fan
7. Mobius On/Off Switch
8. Power Input
9. Thunderbolt 2 Port
9
8
7
(6) Door Lock
A
Locking: Use the included key to lock the door if desired.
B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising