CCM 164 - Selektro

CCM 164
Communication and Control Module
CCM 164 is a control and monitoring module with analog and digital inputs and relay outputs. All inputs and
outputs can be monitored and controlled via SMS (Short Message Service) or via a data connection. The
network is defined by the service provider’s SIM card.



An analog 4-20 mA or 0-20 mA input.
Six digital (24 VDC) or analog (0-10 V) inputs.
Four relay outputs - two power relays and two switching relays.
The User Manual can be retrieved from www.selektro.dk under Manuals.
This manual complies from firmware version 1.10.
CCM 164 – Overview manual – GB / US
Copyrights Selektro A/S 2016
Selektro A/S
Erhvervsvej 33,
DK-9632 Møldrup.
Denmark
0881-1344004 V04
Getting started:
INPUTS
NET STATUS
Displays the digital value of
the 6 combined digital and
analog inputs.
Flashes when the
MODEM is powered
ON.
MODEM STATUS
STATUS
Flashes slowly when all
is OK. Flashes quickly
when the unit starts or
if there is an error.
Flashes slowly when
the MODEM is ready.
For further details refer
to the table below.
MODE
Used for confirmations
and unlocking.
Mini SIM card
85.6 x 53.98 mm
Remember that the
card must not have a
PIN code.
OUTPUTS
Display level.




Control lamps:
Retrieve the User Manual from www.selektro.dk under Manuals, and read it thoroughly.
Install a SIM card in the holder beneath the cover. Note that the SIM card must not have a
PIN code.
Turn on the power supply and wait 30 seconds until the STATUS flashes slowly.
The module is now ready for configuration. Follow the instruction in the User Manual.
Constanly on
STATUS
Slow long flashing
Slow flashing
Quick flashing
50% on
50% flashing
NET
STATUS
Turned off
Slow flashing
Turned off
MODEM STATUS
Slow long flashing
Slow short flashing
Slow flashing
Two quick flashes
Quick flashing
Turned off
50% on/off flashing
on
Module recently connected to the power
off supply and backup battery is charging.
on
off
on
off
on
off
on
off
on
Module is ready and everything is OK.
There is an error. Refer to MODEM STATUS.
EEPROM error.
No supply voltage. If MODEM STATUS is
off flashing the module is using the backup.
on
off
on
off
on
off
on
Module is initializing.
MODEM is operational.
MODEM is turned off.
MODEM is initializing.
The module is using the backup. STATUS
off LED turned off.
on
off
on
off
on
off
on
off
on
off
MODEM is ready with NET connection.
SIM card error.
GSM network error.
MODEM is turned off.
Modem transmitting
Accessories:


Stub Antenna, order number: 0991-70010001
Planar Mobile Antenna, order number: 0991-70010003
Technical specifications:
Supply voltage
Inputs
Outputs
Storage temperature
Operational temperature
Humidity
Protection
Weight
Dimensions
GSM/GPRS
UMTS/HSPA
*a
Internal backup
Connection:
230 VAC
1 x current 0..20 mA or 4-20 mA
6 x Digital- or voltage inputs
+V supply for inputs
2 x Relay output power
2 x Relay outputs
-40 … +85°C
*a
-20 … +60°C
10% - 95%
IP20
250 g
88 x 90 mm
Quad-band GSM
850/900/1800/1900 MHz
Dual mode UMTS/GSM
*b
850/900/1800/1900/2100 MHz
*c
2 SMS messages @ 2 minutes
+10 % / -20 % / 50-60 Hz
±0,5 %
Low <5 V / High >12 V or 0–10 V ±1 %
24 VDC ±20 %, max. 100 mA
NO – max. 10 A AC1
CO – max. 2 A AC1
*a
Not in direct sunlight
DIN-rail mounted, 5 module width
*b
*c
Unit with 3G option
is NET-provider specific

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project