CC85XX Headset Development Kit Quick Start

CC85XX Headset Development Kit Quick Start
SWRU282
March 2011
CC85XXDK-HEADSET Quick Start Guide
1. Kit Contents
2. Purpose of this Quick Start
Guide
3. Plug the batteries to each of
the Headset boards
This quick start guide will provide step-bystep instructions showing how to set up an
audio link between two wireless units
provided in the development kit.
The CC8531 on each of the boards are
pre-programmed with firmware to stream
audio from the Master microphone input to
the Slave headphone output.
Please
follow step 3 to 9. Information on how to
upgrade with latest firmware, see step 10.
For more details on CC85XX, see the
product folder of the CC8520 [1].
The following items are included in the
CC85XXDK-HEADSET:
2 x CC85XX Headset boards
2 x Battery
1 x CC Debugger
1 x USB micro cable
1 x 3.5mm jack to 3.5mm jack cable
Documentation
Performance and functionality of the
CC8531 are strongly dependant on the
firmware. Thus, for performance testing
etc make sure the firmware used is the
latest released firmware from the TI web
site, see step 10.
If anything is missing in the CC85XXDKHEADSET please contact your local TI
sales representative.
4. Power up both boards
In the pre-programmed firmware
the
toggling between power modes OFF and
ON is mapped to pressing the rocker
switch IN for 1.6 seconds. The two boards
are unpaired out-of-the-box, so in the ON
power mode the topmost LED should flash
once every second indicating network
state ALONE . In the OFF power mode
the LED is turned off. Make sure both
boards are flashing.
There’s only one way to connect the
battery plug to the socket on the board.
With the pre-programmed firmware the
CC8531 enters the OFF power mode
when the battery is connected. The
batteries should have enough charge outof-the-box to establish a link and stream
audio. To charge the battery, see section
9. With full battery the link should run for
typically 15 hours, the Master being the
bottleneck. The Slave plays audio for 22
hours typically.
5. Connect an audio source to
the Master
6. Connect a headphone to the
Slave
Connect an audio source (CD-player,
MP3-player or similar) to the line in
connector on the Master Headset board
(labeled Master on the back side) via the
3.5mm jack cable.
Connect a headphone to the 3.5mm
headphone output on the board labeled
Slave on the back side.
The Master is pre-programmed with
firmware to set up the onboard
TLV320AIC3204 codec [2] to power down
the DAC and use the line in connector as
source to the ADC input.
The Slave is pre-programmed with
firmware to set up the onboard
TLV320AIC3204 codec [2] to power down
the ADC and have the headphone
connector as destination of the DAC
output.
SWRU282
March 2011
7. Pairing
In the pre-programmed firmware the
pairing button is mapped to pressing the
rocker switch IN (not hold, which is power
toggling as described in 4).
Press the pairing button on either board
and observe that the LED blinking pattern
changes. It will now flash two times per
second which indicates that the device is
trying to pair with another device.
8. Volume control
9. Charging
To charge the battery, simply connect the
USB micro cable while the battery is also
connected. The charge voltage should be
5V (plugging the USB cable in your
computer will work perfectly). The bottom
LED will be lit indicating charging. When
the battery is fully charged the LED will go
dark.
The pre-programmed Slave firmware is
configured to have so-called “local volume
control” meaning that the Slave controls
its own volume locally. The volume
buttons are mapped to clicking/holding the
rocker switch UP and DOWN.
The Headset board can be powered from
USB alone (remove the battery and
connect USB cable). Then the LED will be
lit the whole time.
Audio can be streamed while charging.
For information about the single chip
charger and DC/DC converter, see [4].
If the pairing button on the other board is
pressed within 10 seconds the devices will
pair. The Master status LED will be
constantly lit, and the Slave status LED
will flash once every 2.5 seconds. Audio is
now being streamed to the Slave.
When successfully paired the Slave will
save the Master’s device ID in non-volatile
memory and automatically try to pair with
this Master whenever in the ALONE state.
Thus pressing the pairing buttons again
will no longer be necessary (unless the
Slave is re-programmed or paired with
another Master).
10. PurePath Wireless
Configurator
A. More information
B. References
On Texas Instruments’ Low-Power RF
web site you will find all our latest
products, application and design
notes, FAQ section, news and events
updates, and much more. Just go to
www.ti.com/lprf
[1] CC8520 product web page
http://www.ti.com/CC8520
[2] TLV320AIC3204 product web
page
http://focus.ti.com/docs/prod/folders/p
The Low Power RF Online Community rint/tlv320aic3204.html
has forums, blogs and videos. Use the
forums to find information, discuss and get
help with your design. Join us at
www.ti.com/lprf-forum
The next step is to download the PurePath
Wireless Configurator (PPWC) [3]. PPWC
makes it possible to explore all the
configuration options of the CC85XX
family. After creating device configurations
for Master and Slave network roles,
PPWC can program the CC85XX devices
directly
through
the
CCDebugger
(included in the kit).
[3] PPW Configurator product web
page
http://www.ti.com/ppwc
The TI LPRF eNewsletter keeps you up to
date on e.g. new products, application
notes, software and events. Sign up at
www.ti.com/lprfnewsletter
[4] BQ25015 product web page
http://focus.ti.com/docs/prod/folders/p
rint/bq25015.html
We hope you will enjoy working with the
CC85XX and associated Low-Power RF
products from Texas Instruments.
[5] CC2590 product web page
http://focus.ti.com/docs/prod/folders/p
rint/cc2590.html
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising