SV431DPU3A2 KVM switch quick start guide

SV431DPU3A2 KVM switch quick start guide
Quick start guide
4-Port KVM Switch for DisplayPort Computers - USB 3.0
Rear view
SV431DPU3A2
Console DisplayPort
connector
FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com
Packaging contents
•
•
•
•
PC connection PC audio port
ports
(x4)
Power input
PC USB ports
Console USB
port
keyboard and Console audio
mouse ports
port
1 x 4-port DisplayPort™ KVM switch
4 x rubber feet
1 x universal power adapter (NA/EU/UK/AU)
1 x quick start guide
USB 3.0 port
Attach the rubber feet
System requirements
• Host computer with a USB 2.0 or USB 3.0 port
• DisplayPort equipped computer
• Display device (for example, monitor, TV, and so on) equipped with
DisplayPort
• USB keyboard and mouse support
The maximum resolution for this KVM switch is 4K @30 Hz.
Note: To obtain the maximum USB throughout, you must use a
computer with a USB 3.0 port.
System requirements are subject to change. For the latest
requirements, please visit www.startech.com/SV431DPU3A2.
About USB 3.0 and USB 3.1 Gen 1
USB 3.0 is also known as USB 3.1 Gen 1. This connectivity standard
offers speeds up to 5 Gbps.
Product diagram
Front view
Console USB
keyboard and Port selection/link LEDs
Power button
mouse port
USB 3.0 ports
Port selection buttons
To affix the rubber feet to the bottom of the KVM switch, peel off the
backing on each rubber foot and stick the feet to the bottom of the
KVM switch in the indicated areas.
Connect the console to the KVM switch
1. Turn off your computer and any devices or peripherals that are
connected to it (for example, printers, external hard drives, and so
on).
2. Connect a monitor to the Console DisplayPort connector on the
KVM switch.
3. Connect a USB keyboard and mouse to the Console USB
keyboard and mouse ports on the KVM switch.
4. If necessary, connect speakers or a headset to the Console audio
port on the KVM switch.
Connect computers to the KVM switch
You can connect up to four computers to the KVM switch.
1. Connect a male-to-male DisplayPort cable from the DisplayPort
port on the computer to one of the numbered PC connection
ports on the KVM switch.
2. Connect a USB A to B cable from the USB port on the computer to
the corresponding numbered PC USB port on the KVM switch.
3. If you’re using audio, connect a set of audio cables from the
speaker port on your computer to the corresponding PC audio
port on the KVM switch.
4. Repeat steps 2 and 3 for any additional computers that you want
to connect to the KVM switch.
5. Connect the keyboard and mouse that you want to share
between computers to the Console USB keyboard and mouse
ports.
Note: If you want to use USB 3.1 Gen 1 peripherals between all of the
connected computers, make sure that the peripherals are connected
to the USB 3.0 ports on the KVM switch.
6. Connect the universal power adapter from a wall outlet to the
power input port on the KVM switch.
*actual product may vary from photos
For the latest information, technical specifications, and support for
this product, please visit www.startech.com/SV431DPU3A2.
Manual Revision: 12/23/2015
7. To turn on the KVM switch, press the Power button. The LED
indicator should illuminate to indicate that the KVM switch is
receiving power.
8. Turn on the first computer or device that you connected to the
KVM switch. Wait for it to fully load and then test the keyboard
and mouse functionality of the connected computer or device.
Repeat this step for all of the connected computers or devices.
You should now be able to switch between the connected
computers or devices. If you’re experiencing issues with the KVM
switch, see the Troubleshooting topic.
About driver installation
You don’t need to install any drivers for this KVM switch, as the
keyboard and mouse use generic USB drivers that are already
installed on any operating system that supports USB technology.
Select a port
To select a port, press one of the numbered Port selection buttons
located on the front of the KVM switch.
You can also use hotkey commands to select a port and turn on
AutoScan. For more information, view the full product manual at
www.startech.com/SV431DPU3A2.
Note: Different operating systems use different naming conventions.
For more information about changing the BIOS settings, contact the
manufacturer of the motherboard or system.
About LED indicators
The KVM switch features five LED indicators: One LED indicator for
each of the four port connections and one Power LED. For more
information about the LED indicators, see the table below:
LED behavior
Significance
Port selection/link LEDs
LED is illuminated green
The port is active and the connected
computer or device is turned on.
LED is illuminated red
The computer or device connected to
the port is currently selected.
Power LED
LED is illuminated
The KVM switch is turned on.
Troubleshooting
If you experience issues using the KVM switch and you’re using a PC,
you might need to make the following changes to the BIOS settings
on your computer:
1. Set HALT ON ERROR to All but keyboard.
2. In PNP AND PCI SETUP, do the following:
• Set PNP OS INSTALLED to Yes.
• Set USB IRQ to Enabled.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the
equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and
access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two-year warranty.
StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for
repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not
allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising