Integrated Amplifier Amplificateur Intégré

Integrated Amplifier Amplificateur Intégré
U
Integrated Amplifier
Amplificateur Intégré
OWNER’S MANUAL
MODE D’EMPLOI
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
1
2
3
4
5
6
7
8
9
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain
this Owner’s Manual in a safe place for future reference.
10
11
12
13
14
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been
dropped.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
i En
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Corporation of America A/V Division, 6600
Orangethorpe Avenue, Buena Park, CA 90620, USA.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot and fully insert.
CAN ICES-3 (B)/NMB-3(B)
ii En
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry,
clean place - away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold. For proper
ventilation, allow the following minimum clearances
around this unit.
Top: 30 cm (11-3/4 in)
Rear: 20 cm (7-7/8 in)
Sides: 20 cm (7-7/8 in)
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to this
unit, and/or personal injury.
Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to an AC wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the AC wall
outlet, grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from an AC wall
outlet or this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the AC wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
iii En
17 Before moving this unit, press A (power) to set this unit
to standby mode, and then disconnect the AC power plug
from the AC wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this unit
alone for cooling.
20 Install this unit near the AC wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
22 Excessive sound pressure from earphones and
headphones can cause hearing loss.
This unit is not disconnected from the AC power source as long as
it is connected to the AC wall outlet, even if this unit itself is turned
off by A. This state is called the standby mode. In this state, this
unit is designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This label is required to be attached to a product of which
the temperature of the top cover may be hot during
operation.
CONTENTS
Front panel ........................................................2
Rear panel .........................................................4
Remote control..................................................6
PLAYBACK................................................. 11
Playing a source ............................................. 11
Adjusting to the desired sound ....................... 12
TROUBLESHOOTING.............................. 13
SPECIFICATIONS ..................................... 15
CONNECTIONS............................................ 9
Connecting speakers and source components...9
Connecting power cable..................................10
About this manual
• y indicates a tip for your operation.
• The illustrations used in this Owner’s Manual are A-S701.
• Depending on the model, there are some countries/regions where it may not be sold.
USEFUL FEATURES
This unit allows you to:
◆ Enjoy the highest sound quality of compact discs by
using the CD direct function (A-S701 only)
(see page 12)
◆ Enjoy pure, high fidelity sound by using the Pure
Direct function (see page 12)
◆ Save power by using AUTO POWER STANDBY
switch (see page 4)
◆ Use the remote control of this unit to operate a Yamaha
tuner and/or CD player (see page 7)
◆ Boost bass sounds by connecting a subwoofer
(see page 9)
SUPPLIED ACCESSORIES
Please check that you received all of the following parts.
Remote control
Batteries (x2)
(AA, R6, UM-3)
Power cable
(A-S701 only)
1 En
English
USEFUL FEATURES ................................... 1
SUPPLIED ACCESSORIES......................... 1
CONTROLS AND FUNCTIONS................. 2
CONTROLS AND FUNCTIONS
Front panel
(A-S701)
1
A (power) switch
Turns on and off the power of this unit.
4 PHONES jack
Connect your headphones.
Note
5 SPEAKERS selector
Even when this unit is turned off, this unit consumes a small
amount of power.
2 Power indicator
Indicator
Status
Brightly lit
The power of this unit is “on”.
Dimly lit
This unit is in “standby” mode.
For details on the “standby” mode, see
page 6.
Off
The power of this unit is “off”.
3 Remote control sensor
Receives infrared signals from the remote control.
2 En
Selector
position
Speaker status
OFF
Both sets of speakers are off.
A or B
The set of speakers connected to the A
or B terminals is on.
A+B BI-WIRING
Both sets of speakers are on.
6 BASS control
Increases or decreases the low frequency response.
The 0 position produces a flat response.
Control range: –10 dB to +10 dB
7 TREBLE control
Increases or decreases the high frequency response.
The 0 position produces a flat response.
Control range: –10 dB to +10 dB
CONTROLS AND FUNCTIONS
English
(A-S701)
8 BALANCE control
Adjusts the sound output balance of the left and right
speakers to compensate for sound imbalances.
Note
If you rotate the BALANCE control to the end of L (left) or
R (right), the opposite side of channel is muted.
9 LOUDNESS control
Retain a full tonal range at any volume level
(see page 12).
0 INPUT selector and indicators
Selects the input source you want to listen to. The
input source indicators light up when the
corresponding input sources are selected.
A VOLUME control
Increases or decreases the sound output level.
B CD DIRECT AMP button and indicator
(A-S701 only)
Reproduces CD sound in the highest signal quality
(see page 12).
The indicator above it lights up when this function is
turned on.
C PURE DIRECT button and indicator
Reproduces any input source in the purest sound
possible (see page 12).
The indicator above it lights up when this function is
turned on.
y
The input source names correspond to the names of the
connection jacks on the rear panel.
3 En
CONTROLS AND FUNCTIONS
Rear panel
(A-S501/S301)
(A-S701)
1 CD input jacks
Used to connect a CD player (see page 9).
2 PHONO jacks and GND terminal
Used to connect a turntable that uses an MM cartridge,
and to ground the terminal (see page 9).
3 Audio input/output jacks
Used to connect external components, such as a tuner,
etc (see page 9).
4 DIGITAL (OPTICAL) jack
Used to connect a component with a digital optical
output (see page 9).
5 DIGITAL (COAXIAL) jack
Used to connect a component with a digital coaxial
output (see page 9).
4 En
6 DC OUT jack
For supplying power to a Yamaha AV accessory. For
details on connections, refer to the instruction manual
of the AV accessory.
7 SPEAKERS A/B terminals
Used to connect one or two speaker sets (see page 9).
8 SUBWOOFER OUT jack
Used to connect a subwoofer with built-in amplifier
(see page 9).
y
The SUBWOOFER OUT jack attenuates signals over 90 Hz.
9 AUTO POWER STANDBY switch
Switch
position
Status
ON
The unit enters standby mode
automatically if not operated for 8
hours.
OFF
The unit does not enter standby mode
automatically.
CONTROLS AND FUNCTIONS
(A-S501/S301)
English
(A-S701)
0 VOLTAGE SELECTOR (General model only)
Used to set to your local main voltage (see page 10).
A IMPEDANCE SELECTOR switch
CAUTION
Do not change the IMPEDANCE SELECTOR switch
while the power is turned on, as doing so may damage
the unit.
If the IMPEDANCE SELECTOR switch may not be
fully slid to either position, remove the power cable
and slide the switch all the way to either position.
Select the switch position according to the impedance
of the speakers.
Speaker
connection
SPEAKERS A
or
SPEAKERS B
SPEAKERS A
and
SPEAKERS B
Bi-wiring
Speaker
impedance
B AC IN (A-S701)
Used to connect the supplied power cable to an AC
wall outlet (see page 10).
Power cable (A-S501/S301)
Used to connect this unit to an AC wall outlet
(see page 10).
Switch
position
6 Ω or higher
HIGH
4 Ω or higher
LOW
8 Ω or higher
LOW
6 Ω or higher
HIGH
4 Ω or higher
LOW
5 En
CONTROLS AND FUNCTIONS
Remote control
(A-S701)
1 Infrared signal transmitter
Sends infrared signals.
2
A AMP
Turns this unit on, or sets it to standby mode.
3
OPEN/CLOSE
Opens/closes the disc tray of the Yamaha CD player.
Refer to the owner’s manual of your CD player for
details.
Note
Even when using a Yamaha CD player, certain components
and features may not be available.
(A-S501/S301)
4
A CD
Turns the Yamaha CD player on, or sets it to standby
mode. Refer to the owner’s manual of your CD player
for details.
Note
Even when using a Yamaha CD player, certain components
and features may not be available.
5 CD DIRECT AMP (A-S701 only)
Reproduces CD sound in the highest signal quality
(see page 12).
6 Input selector buttons
Selects the input source you want to listen to.
y
The input source names correspond to the names of the
connection jacks on the rear panel.
6 En
CONTROLS AND FUNCTIONS
7 VOLUME +/–
Increases or decreases the sound output level.
9 PURE DIRECT
Reproduces any input source in the purest sound
possible (see page 12).
0 Yamaha tuner control buttons
The following buttons can be used to control various
functions of a Yamaha tuner.
Refer to your component’s owner’s manual for more
information.
w
f
DISC SKIP
e
b
a
p
s
Rewinds playback
Fast-forwards playback
Skips to the next disc in a CD changer
(A-S501/S301 only)
Pauses playback
Skips backward
Skips forward
Starts playback
Stops playback
Note
Even when using a Yamaha CD player, certain components
and features may not be available.
BAND
Selects the reception band (FM/AM).
TUNING jj / ii
Selects the tuning frequency.
MEMORY
Stores the current FM/AM station as a preset.
PRESET j / i
Selects a preset FM/AM station.
Note
Even when using a Yamaha tuner, certain components and
features may not be available.
7 En
English
8 MUTE
Reduces the current volume level by approximately
20 dB. Press again to restore the audio output to the
previous volume level. Pressing the VOLUME +/–
also cancels muting.
The input indicator on the front panel for the current
input source blinks while the output is muted.
A Yamaha CD player control buttons
The following buttons can be used to control a
Yamaha CD player.
Refer to your component’s owner’s manual for more
information.
CONTROLS AND FUNCTIONS
■ Installing batteries
AA, R6, UM-3 batteries
■ Operation range
Point the remote control at the remote control sensor on
this unit and remain within the operating range shown
below.
Approximately
6m
(20 ft)
Remote control
■
•
•
•
•
•
•
•
•
•
•
•
•
Notes on remote control and batteries
The area between the remote control and this unit must be clear of large obstacles.
Be careful not to spill water or other liquids on the remote control.
Be careful not to drop the remote control.
Do not leave or store the remote control in the following conditions:
– places of high humidity, such as near a bathroom
– places of high temperatures, such as near a heater or stove
– places of extremely low temperatures
– dusty places
Change all batteries if you notice the operation range of the remote control narrows.
If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.
If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material
comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery
compartment thoroughly before installing new batteries.
Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.
Do not use different types of batteries (such as alkaline and manganese batteries) together. Batteries that look the same may have a
different specification.
Dispose of batteries according to your regional regulations.
Keep the batteries in a location out of reach of children.
Batteries can be dangerous if a child were to put in his or her mouth.
If you plan not to use this unit for a long period of time, remove the batteries from this unit. Otherwise, the batteries will wear out,
possibly resulting in a leakage of battery liquid that may damage this unit.
8 En
CONNECTIONS
Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will
be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and
lack bass. Refer to the owner’s manual for each of your components.
Make sure to use RCA cables or optical cable to connect audio components.
CAUTION
Do not connect this unit or other components to the main power until all connections between components are complete.
Turntable
DVD player,
etc.
Tuner
Audio
out
GND
Audio
out
CD player
Speakers A
Right
Left
TV, etc.
Audio
out
Audio
out
Audio
out
Audio
In
Tape deck,
etc.
BD player, etc.
Audio
out
Audio
In
Audio
out
Audio
out
CD recorder,
etc.
Subwoofer
Right
Left
Speakers B
Only PCM signals can be input to the DIGITAL (OPTICAL/COAXIAL) jacks of this unit. For details on the supported
PCM signals, see page 15.
y
• The PHONO jacks are designed for connecting a turntable with an MM cartridge.
• Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise
without the GND connection.
9 En
English
Connecting speakers and source components
CONNECTIONS
■ REC jacks
Rear panel
• The audio signals are not output via the LINE 2 REC
or LINE 3 REC output jacks when LINE 2 or LINE 3
is selected with the INPUT selector.
• The VOLUME, BASS, TREBLE, BALANCE and
LOUDNESS controls and the CD DIRECT function
(or the PURE DIRECT function) have no effect on the
source being recorded.
Speaker
■ Connecting speaker cables
1 Remove approximately 10 mm (3/8 in) of insulation
from the end of each speaker cable.
2 Twist the bare wires of the cable firmly together.
3 Unscrew the knob.
4 Insert one bare wire into the hole in the side of each
terminal.
5 Tighten the knob to secure the wire.
Connect the other speaker to the other set of terminals in
the same way.
Note
When making bi-wire connections, remove the shorting bridges
or cables on the speaker. Refer to the speakers’ instruction
manuals for more information.
y
To use the bi-wire connections, set the SPEAKERS selector on
the front panel to the A+B BI-WIRING position.
10 mm (3/8 in)
Red: positive (+)
Black: negative (–)
Connecting power cable
CAUTION
CAUTION
• Set the IMPEDANCE SELECTOR switch according to
the impedance of the speakers to be connected (see
page 5).
• Do not let bare speaker wires touch each other or any
metal part of this unit. This could damage this unit and/
or the speakers.
■ Connecting via banana plug
(North America, General, China and
Australia models only)
1 Tighten the knob.
2 Insert the banana plug into the end of the
corresponding terminal.
Banana plug
■ Bi-wire connection
In the case of speakers supporting the bi-wiring
connection, the tweeter/midrange unit and woofer of the
speakers can be driven independently through connections
shown in the following figure, allowing you to enjoy clear
mid- and high-range sounds.
10 En
(General model only)
Before connecting the power cable, make sure you set
VOLTAGE SELECTOR of this unit according to your
local voltage. Improper setting of VOLTAGE SELECTOR
may cause fire and damage to this unit.
■ AC IN (A-S701)
Connect the supplied power cable to AC IN after all other
connections are complete.
■ Power cable (A-S501/S301)
Connect the power cable to an AC wall outlet after all
other connections are complete.
To the AC
wall outlet
(A-S501/S301)
To the AC
wall outlet
(A-S701)
PLAYBACK
SPEAKERS
4
VOLUME
Rotate the SPEAKERS selector on the front
panel to select SPEAKERS A, B or A+B BIWIRING.
y
Set the SPEAKERS selector to the A+B BI-WIRING position
when two sets of speakers are connected using bi-wire
connections, or when using two sets of speakers simultaneously
(A and B).
(A-S701)
A
5
Play the selected input source.
6
Rotate the VOLUME control on the front
panel (or press VOLUME +/– on the remote
control) to adjust the sound output level.
INPUT
A AMP
Input selector
buttons
y
You can adjust to the desired sound by using the BASS,
TREBLE, BALANCE and LOUDNESS controls, the CD
DIRECT AMP button, or the PURE DIRECT button on the front
panel.
7
When finished listening, press A (power)
switch on the front panel outward to turn off
this unit.
y
VOLUME +/–
1
Rotate the VOLUME control on the front
panel fully counter-clockwise so as not to
play sounds loud suddenly.
2
Press A (power) switch on the front panel
inward to turn on this unit.
3
Rotate the INPUT selector on the front panel
(or press one of the Input selector buttons on
the remote control) to select the input source
you want to listen to.
The indicator for the selected input source lights up.
If A AMP on the remote control is pressed while the A (power)
switch on the front panel is in the on position, this unit enters
standby mode. Press A AMP again to turn this unit on.
11 En
English
Playing a source
PLAYBACK
Adjusting to the desired sound
LOUDNESS
VOLUME
■ Reproducing pure, high fidelity sound
(PURE DIRECT)
When the PURE DIRECT function is on, noise can be
reduced by bypassing the circuit that the audio input
signal is not using and stopping the power supply to the
circuit.
Therefore, in all input sources, you can enjoy music
playback in straight and high quality sound.
The indicator above the PURE DIRECT button lights up
when this function is turned on.
Note
(A-S701)
CD DIRECT
AMP
PURE
DIRECT
■ Making it easier to hear the high- and
low-frequency ranges even at low
volume (LOUDNESS)
Enjoy natural sound even at low volume by lowering the
mid-range sound level and compensating for the human
ears’ loss of sensitivity to high- and low-frequency ranges
at low volume.
CAUTION
If the CD DIRECT AMP function (or the PURE DIRECT
function) is turned on with the LOUDNESS control set at
a certain level, the input signals bypass the loudness
control, resulting in a sudden increase in the sound output
level. To prevent your ears or the speakers from being
damaged, be sure to press the CD DIRECT AMP button
(or the PURE DIRECT button) AFTER lowering the
sound output level or AFTER checking that the
LOUDNESS control is properly set.
1
Set the LOUDNESS control to the FLAT
position.
2
Rotate the VOLUME control on the front
panel (or press VOLUME +/– on the remote
control) to set the sound output level to the
loudest listening level that you would listen
to.
3
Rotate the LOUDNESS control
counterclockwise until the desired volume is
obtained.
12 En
The BASS, TREBLE, BALANCE and LOUDNESS controls do
not function while the PURE DIRECT function is turned on.
■ Reproducing CD sound with the highest
sound quality (CD DIRECT AMP)
(A-S701 only)
When selecting the input source other than CD, if you
press the CD DIRECT AMP button, the input source
switches to CD.
CD Direct Amp feature
Stop power supply to the unnecessary circuit for CD
playback, convert the input signal to the normal phase
and reverse phase, and balance transfer to the electronic
volume. With the following effects, a more faithful
sound to the original will be provided.
• improved signal-to-noise ratio
• external noise canceling
• reduced distortion
Notes
• The BASS, TREBLE, BALANCE and LOUDNESS controls do
not function while the CD DIRECT AMP function is turned on.
• Be sure to connect the CD player to the CD input jacks if you
use the CD direct function.
• The CD DIRECT AMP function is turned off if the following
operation is performed.
– Select an input source other than CD for the INPUT selector.
– The PURE DIRECT function is turned on.
TROUBLESHOOTING
Problem
This unit fails to turn
on.
This unit turns off
suddenly and the
power indicator
blinks.
Cause
See
page
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
The A AMP is pressed on the remote
control while this unit is turned off.
Press A (power) switch on the front panel to on.
The impedance setting of the connected
speaker is too small.
Use speaker(s) with proper speaker impedance.
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
10
There is a problem with the internal
circuitries of this unit.
Disconnect the power cable and contact the nearest
authorized Yamaha dealer or service center.
—
The speaker wires are touching each other
or shorting out against the rear panel.
Connect the speaker cables properly and press the A
(power) switch again. The INPUT indicators blink
and the volume is decreased to the lowest setting
automatically, then the INPUT indicators stop
flashing and the last input source selected lights up.
Confirm normal sound output from speakers by
increasing the volume gradually.
10
Replace the speaker set and press the A (power)
switch again. The INPUT indicators blink and the
volume is decreased to the lowest setting
automatically, then the INPUT indicators stop
flashing and the last input source selected lights up.
Confirm normal sound from speakers by increasing
the volume gradually.
—
The protection circuitry has been activated
because of excessive input or excessive
volume level.
Rotate the VOLUME control on the front panel to
decrease the volume level and then turn the power on
again.
—
The protection circuitry has been activated
due to excessive internal temperature.
Allow about 30 minutes for the temperature inside
this unit to decrease, rotate the VOLUME control on
the front panel to lower the volume and then turn the
power on again. Set the unit in a place where heat can
readily dissipate from the unit.
—
The IMPEDANCE SELECTOR switch is
not fully slid to either position.
Turn the power off and slide the IMPEDANCE
SELECTOR switch all the way to the correct position.
5
The IMPEDANCE SELECTOR switch is
not set to the correct position.
Set the IMPEDANCE SELECTOR switch to the
position that corresponds to the impedance of your
speakers.
5
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Turn off this unit, disconnect the power cable, plug it
back in after 30 seconds, then use the unit normally.
There is a problem with the internal
circuitries of this unit.
Disconnect the power cable and contact the nearest
authorized Yamaha dealer or service center.
—
Sound is muted.
Press MUTE on the remote control or rotate the
VOLUME control.
7
Incorrect cable connections.
Connect the stereo cable for audio units and the
speaker wires properly. If the problem persists, the
cables may be defective.
9
The speaker is malfunctioning.
No sound.
Remedy
10
2
5
—
13 En
English
Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or
if the instructions below do not help, turn off this unit, disconnect the power cable, and then contact the nearest
authorized Yamaha dealer or service center.
TROUBLESHOOTING
Problem
Cause
Remedy
See
page
Playback has been stopped on the
connected component.
Turn the component on and start playback.
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or one of the Input
selector buttons on the remote control).
11
The SPEAKERS selector is not set
properly.
Set the corresponding SPEAKERS selector to A, B or
A+B BI-WIRING position.
11
The output audio source setting on the
connected component is not PCM.
Only PCM audio sources can be played via the
DIGITAL (OPTICAL/COAXIAL) jacks of this unit.
Set the output audio source of the connected
component to PCM.
16
The automatic power down function has
activated.
Confirm that there are no other issues causing this
problem, and then turn this unit on again.
To turn off the AUTO POWER STANDBY function,
set the AUTO POWER STANDBY switch to OFF on
the rear panel.
4
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
9
Incorrect setting for the BALANCE
control.
Set the BALANCE control to the appropriate
position.
3
There is a lack of bass
and no ambience.
The + and – wires are connected in
reverse at the amplifier or the speakers.
Connect the speaker wires to the correct + and –
phase.
10
A “humming” sound
can be heard.
Incorrect cable connections.
Connect the audio plugs firmly. If the problem
persists, the cables may be defective.
No connection from the turntable to the
GND terminal.
Make the GND connection between the turntable and
this unit.
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the LINE 2
REC or LINE 3 REC jacks of this unit is
turned off.
Turn on the power of the component.
The sound is
degraded when
listening with
headphones
connected to a CD
player connected to
this unit.
This unit is turned off or is in standby
mode.
Turn on the power of this unit.
The sound level is
low.
Sound is muted.
Press MUTE on the remote control or rotate the
VOLUME control.
7
The loudness control function is
operating.
Turn down the volume, set the LOUDNESS control
to the FLAT position, and then adjust the volume
again.
12
The turntable is connected to the jacks
other than the PHONO jacks.
Connect the turntable to the PHONO jacks.
The record is being played on a turntable
with an MC cartridge.
Use a turntable equipped with an MM cartridge.
The CD DIRECT function or the PURE
DIRECT function is turned on.
The CD DIRECT function or the PURE DIRECT
function must be turned off to use those controls.
No sound.
The sound suddenly
goes off.
Only the speaker on
one side can be
heard.
The volume level is
low while playing a
record.
Using the BASS,
TREBLE, BALANCE
and LOUDNESS
controls does not
affect the sound.
14 En
11
9, 10
9
—
—
9
9
12
SPECIFICATIONS
AUDIO SECTION
Minimum RMS output power
A-S701
A-S501
A-S301
8 Ω, 20 Hz to 20 kHz, 0.019% THD
100 W + 100 W
85 W + 85 W
60 W + 60 W
6 Ω, 20 Hz to 20 kHz, 0.038% THD
(Except for Asia and China models)
120 W + 120 W
100 W + 100 W
70 W + 70 W
8Ω
140 W
130 W
100 W
6Ω
170 W
150 W
120 W
4Ω
220 W
185 W
140 W
2Ω
290 W
220 W
150 W
Maximum power per channel
1 kHz, 0.7% THD, 4 Ω
(U.K. and Europe models only)
160 W
120 W
95 W
IEC power
1 kHz, 0.019% THD, 8 Ω
(U.K. and Europe models only)
115 W
100 W
75 w
Dynamic power per channel (IHF)
10 Hz to 50 kHz
—
—
Power band width
0.04% THD, 50 W, 8 Ω
0.04% THD, 42.5 W, 8 Ω
—
10 Hz to 50 kHz
—
0.04% THD, 30 W, 8 Ω
—
—
10 Hz to 50 kHz
Damping factor (SPEAKERS A)
1 kHz, 8 Ω
Maximum Effective Output Power
(JEITA)
Input sensitivity/Input impedance
Maximum input signal
240 or more
210 or more
1 kHz, 10% THD, 8 Ω
(Asia, China and General models
only)
145 W
130 W
100 W
1 kHz, 10% THD, 6 Ω
(General model only)
170 W
—
—
PHONO (MM)
3.0 mV/47 kΩ
CD, etc.
200 mV/47 kΩ
PHONO (MM) (1 kHz, 0. 03%
THD)
45 mV or more
CD etc. (1 kHz, 0.5% THD)
2.2 V or more
REC OUT
Output level/Output impedance
SUBWOOFER OUT (Cut Off
Frequency: 100 Hz)
PHONES jack rated output/
Impedance
CD, etc. (Input 1 kHz, 200 mV,
8 Ω)
200 mV/1.0 kΩ or less
3.5 V/1.2 kΩ
470 mV/470 Ω
430 mV/470 Ω
CD, etc. (20 Hz to 20 kHz)
0 ± 0.5 dB
Frequency response
CD, etc. PURE DIRECT on (10 Hz
to 100 kHz)
0 ± 1.0 dB
RIAA equalization deviation
PHONO (MM)
± 0.5 dB
PHONO (MM) to REC OUT (20
Hz to 20 kHz, 2.5 V)
Total harmonic distortion
360 mV/470 Ω
0.03 % or less
CD, etc. to SPEAKERS (20 Hz to
20 kHz, 50 W, 8 Ω)
0.019 % or less
—
—
CD, etc. to SPEAKERS (20 Hz to
20 kHz, 45 W, 8 Ω)
—
0.019 % or less
—
CD, etc. to SPEAKERS (20 Hz to
20 kHz, 30 W, 8 Ω)
—
—
0.019 % or less
15 En
English
Item
SPECIFICATIONS
Item
Signal to noise ratio (IHF-A
network)
A-S701
A-S501
PHONO (MM)
(5 mV input shorted)
82 dB or more
CD, etc. PURE DIRECT on
(200 mV input shorted)
99 dB or more
CD DIRECT AMP on
104 dB or more
Residual noise (IHF-A network)
Channel separation
A-S301
—
—
40 μV
CD, etc. (5.1 kΩ input shorted,
1 kHz)
65 dB or more
CD, etc. (5.1 kΩ input shorted,
10 kHz)
50 dB or more
BASS
Tone control characteristics
TREBLE
Boost/
Cut (20 Hz)
± 10 dB
Turnover
frequency
400 Hz
Boost/
Cut (20 kHz)
± 10 dB
Turnover
frequency
3.5 kHz
Continuous loudness control
Attenuation (1 kHz)
Supported digital audio format
(OPTICAL/COAXIAL)
PCM (2-ch)
– 30 dB
192/176.4/96/88.2/48/44.1/32 kHz
PCM word depth
24 bit/16 bit
GENERAL
Item
A-S701
U.S.A. and Canada models
AC 220-240 V, 50/60 Hz
General model
Power consumption
AC 110-120 V/220-240 V, 50/60 Hz
China model
—
Korea model
—
AC 220 V, 50 Hz
—
Australia model
AC 240 V, 50 Hz
U.K. and Europe models
AC 230 V, 50 Hz
AC 220 V, 60 Hz
U.S.A and Canada, General,
Australia, U.K and Europe models
270 W
240 W
190 W
Asia model
230 W
220 W
170 W
China model
—
220 W
170 W
Korea model
—
—
190 W
Standby power consumption
0.5 W
Maximum power consumption
1 kHz 6 Ω 10% THD
(General model only)
Dimensions
W×H×D
Weight
Specifications are subject to change without notice.
16 En
A-S301
AC 120 V, 60 Hz
Asia model
Power supply
A-S501
580 W
510 W
430 W
435 × 151 × 387 mm (17-1/8" × 6" × 15-1/4")
11.2 kg (24.7 lbs)
10.3 kg (22.7 lbs)
9.0 kg (19.8 lbs)
Printed in Malaysia ZM52680
fi)YAMAHA
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.
Pour plus de details sur les produits, contactez votre representant Yamaha le plus proche de chez vous ou le distributeur agree indique ci-dessous.
I
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Tronto ON M1S 3R1, Canada
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
I
CENTRAL & SOUTH AMERICA
[
MEXICO
n-
---
-
EUROPE
EUROPEAN COUNTRIES
Yamaha de Mexico S.A. de C. V.
Avenida lnsurgentes numero 1647,
Col. San Jose lnsurgentes, C.P. 03900,
Deleg. Benito Juarez, Mexico, D. F.
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
RUSSIA
Yamaha Music (Russia)
Room 37, bid. 7, Kievskaya street, Moscow,
121059, Russia
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913- 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
I
ARGENTINA
I
AFRICA
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali, Dubai,
United Arab Emirates
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Olga Cossettini 1553, Piso 4 Norte
Madero Este-C1107CEK
Buenos Aires, Argentina
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES I
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanizaci6n Marbella,
Calle 47 y Aquilino de Ia Guardia,
Ciudad de Panama, Panama
~
As of April 2013
AVR01301A
Yamaha Corporation, AV Products Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
"\?";(~' J, ..it~tt
IZF73310-1I
=r
430-8650 D~~~fllffltt:'J(gtt:'J)RIBJ 10- 1
I
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
I I
ASIA
--]
SINGAPORE
Yamaha Music (Asia) PRIVATE LIMITED
Blk 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
THE PEOPLE'S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
TAIWAN
Yamaha Music and Electronics Taiwan Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd., Taipei,
Taiwan, R.O.C
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
INDIA
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
THAILAND
Slam Music Yamaha Co., Ltd.
4, 6, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
VIETNAM
Yamaha Music Vietnam Company, Limited
15th Floor, Nam A Bank Tower
201-203 Cach Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
REPUBLIC OF KOREA
Yamaha Music Korea Ltd.
SF, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
OTHER COUNTRIES
Yamaha Corporation,
Sales & Marketing Div. ASEAN Department
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
I
OCEANIA
AUSTRALIA I NEW ZEALAND
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
- --~
.YAMAHA
Registering Your New Yamaha
Product is Fast and Easy
Thank you for purchasing a new product from Yamaha Electronics. We'd like to
continue providing you with high quality products and better service. So, we've made
it simple to register your new product purchase online. Please take a few minutes to
visit our website at www.yamaha.com/YEC/registration/ and complete the
information and questions included there. We appreciate your business and we look
forward to hearing from you.
Failure to complete the registration form does not diminish your warranty rights in any way.
Product registration applies to USA customers only.
WF15740
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~
b'.'<!ibl:<'ii!>::~"'·"'"'·'<!ib':'~o-.~b':'~o-.'<!ib-~b':'~bl:<'ib'.~b'.~bl:<'ib'.'<!ib-~bl:<'ibl:<'ii!J.'.'<!ibl:<'ib-~b'.;abl:<'io-.'<!io-.;ab'.'<!ibl:<'io-~o-•.,b':'~b-~b'.'<!io-•.,bl:<'ib':'~i!J.'•.,b'•.,M~lll:i'io•.,bl:<'ib'.'<>b'.'<>o-.,.,b-~bl:<'ii!J.~b'.'<~
~
~
~
m
~
~
~
~
~
~
~
~
~~
·~
GARANTXE DE§ A JPP>AREKL§
§TEREOJPHO NKQUE§ YA1\1AHA ~
Yamaha Canada Musique Ltee., garantit a I'acheteur original ses appareils stereophoniques contre toutes
defectuosites de materiaux et de main-d'reuvre, selon les conditions ci-dessous:
Duree de validite de Ia garantie a
partir de Ia date d'achat originate
Appareils
* Recepteurs, amplificateurs, syntoniseurs, lecteurs de disque compact, projecteur de son
numerique, ensembles de haut-parleurs et caissons de graves achetes separementr.. ........ .................... 2 annees
~
~
~
m
ti
~~
~
~
~~
~
~
ti
~1
~
* Lecteurs de DVD, emegistreurs de CD, lecteurs de disque Bluray,
~
~~:~
Iecteurs de musique reseau et gestionnaires, radios-reveils, ensembles de
haut-parleurs iPod, haut-parleurs multimedias, casques d'ecoute, ecouteurs,
systemes integres (recepteur ou amplificateur combine a ou sur Je meme
bati qu'un lecteur de disque optique et haut-parleurs inclus), accessoires ................... .. ......................... I annee
*Cartouc he a Lampe pour Ie ProJecteur
.
...... ................................................................ ........................... 180 jours
~l
~
~
~
~
~
~.q
~~
~
~
~
Sous reserve des conditions stipulees ci-apres, Yamaha Canada Musique Ltee., s'engage a reparer
gratuitement, incluant les pieces et Ia main-d' reuvre, ses appareils stereophoniques devenant defectueux au
cours de Ia duree de Ia garantie applicable.
~
CONDITIONS·.
~
~
~
~
~l
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
[~
~
~l
~
~
~
~l
~
~
~
~
~
~
~
~
~
~
~
~
•
ti
ti
~
~
~""
~~
~
t;t
~
~~
~
1. Les appareils defectueux doivent etre retournes, accompagnes d'une description complete de Ia
defectuosite ct Ia facture d'achat, a un centre de service Yamaha autorise.
2. Le transport, l'emballage et I' assurance sont a Ia charge du proprietaire.
3. La presente garantie ne s'etend pas a l'entretien normal des appareils et est assujettie a leur maintien
en bon etat, conformement au mode d' entretien reproduit dans le manuel d' instructions.
4. Exclus de Ia presente garantie:
a) les dommages materiaux resultant d'un abus d'emploi;
b) les avaries survenues en cours d'expedition;
c) les elements exigeant un entretien periodique, par exemple Ies ampoules, Ies courroies
d'entralnement, le nettoyage des tetes enregistreuses et Ia lubrification;
d) le grillage des bobines mobiles aux haut-parleurs des mediums et des aigus (entralnes par le
fonctionnement des ampliticateurs au-deJa de Ia puissance nominale);
e) le grillage des bobines mobiles aux haut-parleurs des graves (resultant d ' une suralimentation des
haut-parleurs par leur fonctionnement a des niveaux d'alimentation superieurs a leur capacite);
f) les verifications de rendement;
g) Ies fils d'interconnexion et les antennes FM;
h) Ies fusibles qui bn11ent par suite d'une utilisation incorrecte.
5. Cette garantie ne couvre pas les produits qui ont ete a] teres ou repares autre que par un centre de
service autorise Yamaha Audio, ou les appareils dont Ia marque de fabrique, le nom du fabricant, le
numero de modele et le numero de serie ont ete alteres ou enleves.
6. LA GARANTIE NE COUVRE QUE LES APPAREILS A L'ETAT NEUF VENDUS PAR DES
CONCESSIONNAIRES AUTO RISES DE YAMAHA AUDIO AU CANADA, SOUS RESERVE
QUE L' ACHETEUR ORIGINAL EN FASSE UNE UTILISATION NORMALE.
7. La garantie ne couvre pas le appareils stereophoniques de Yamaha Canada Musique Ltee., vend us en
Saskatchewan et auxquels s'appliquent Ies garanties reglementaires prevues par Ia loi intitulee "The
Consumer Products Warranties Act, 1977" (Saskatchewan).
8. Cette garantie ne peut s'exercer dans les territoires ou elle est interdite par Ia loi.
bl:<'i
~
0
~
~
~l
~
~
~l
~
~
ti
~-~
i!JI.,.,
~
~
~
~
~
~
~l
~
t'~
~
t'~
~
~
~l
~
~
t~l
~
[~
~
~
bl:<'i
Adresses des centres de service principaux:
135 Milner Avenue, Scarborough, Ontario, M1 S 3R1.
~
~
T€~1:(416)298-1311
~
~
Pour connaitre l'adresse des autres centres de service Yamaha, renseignez-vous
aupres d'un concessionnaire d'appareils stereophoniques Yamaha ou communiquez
avec l'un des centres ci-dessus.
~
LA CARTE DE GARANTIE N'EST PAS REQUISE.
PRIERE DE CONSERVER VOTRE FACTURE COMME PREUVE D' ACHAT EN CAS DE TO UTES
REPARATIONS EFFECTUEES SOUS LA GARANTIE.
~
W VAMAHA
~
~~~il~~~~~~~~~~t!l~~ ~ 1
j
~l
~
~
~
~
~
010394 ~
~~~;:~~l!l~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~::<!i~Ai~~~;~~; ...:~~~~r>?6r>.<!i~~... i!'.<!iO'•.,~~i!>::<!i~i!'><>~i!'.-ai!'...~i!'.<!i!>'•.,i!'•.,i!'.-aO'•.,i!'.<!i~~.<!i"""~::<!ii!':'~i!>?6i!>::<!i~~~""·"'~i!'•...,i!'.<!ii!'.<!ii!'..,~::<!i~~i!>::<!i
~
~
~
~
§
~YAMAHAAliDKOWARRANTY~
li
~
Yamaha Canada Music Ltd. warrants to the original purchaser of its audio products that such products are
free from defects in workmanship and materials as follows:
~
~
~
~
~
~1
~
~
~
~
~
~
~
~
~
~
~
~
m
~
~
~
~
~
~
~
~
Warranty Period from date
of Original Purchase
Product
~
* Receivers, Amplifiers, Tuners, Compact Disc Players, Digital Sound Projectors,
~
Speaker Systems and Subwoofers purchased individually ...................................................................... 2 years
~
~
* DVD Players, CD Recorders, Blu-ray Disc Players, Network Music Players and
~
Commanders, Clock Radios, iPod Speaker Systems, Powered Multimedia Speakers,
Headphones, Earphones, Integrated Systems (Receiver or Amplifier combined or
on same chassis with an Optical Disc Player along with any included Speakers), Accessories ............... l year
* Lamp Cartridge for Projectors ......................... ......................................................................................
~
~
~
~
~
~
180 days
m
Subject to the following terms and conditions if any Yamaha Canada Music Ltd. audio products become
defective during the applicable warranty period. Yamaha Canada Music Ltd. will repair such product without
charge, including both parts and labour.
~
~
~
~
~
~
~
~
~
~
~
ii
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
i
~
~
~
~
~
~
m
~
~
~
~
~
~
~
~
~
~
~
~
~
~
Terms and Conditions:
l. Defective units must be returned to an authorized Yamaha Audio Service Centre together with a
complete description of the defect, and Bill of Sale.
2. Any transportation, packing and insurance arrangements are the responsibility of the owner.
3. This warranty does not cover normal maintenance of the products and is subject to the products being
properly maintained in accordance with the maintenance instructions contained in the Yamaha
Owner's Manual.
4. This Warranty does not cover:
a) Physical damage due to abuse:
b) Shipping damage.
c) Normal maintenance items such as: light bulbs, drive belts, dirty tape heads, lubrication.
d) Burned voice coils on tweeter and midrange speakers (caused by amplifier chipping, i.e. operation
of amplifier beyond rated wattage.)
e) Burned voice coils on woofers (caused by overpowering the speakers, i.e. operation of amplifier at
power levels beyond speaker capability).
f) Performance checks.
g) Interconnection cables and FM antennas.
h) Blown fuses caused by improper operation.
5. This warranty does not cover products which have been altered or repaired ·other than by an
authorized Yamaha Audio Service Centre, or products whose trademark name, model, or serial
number have been altered or removed.
6. THIS WARRANTY COVERS ONLY NEW AND UNUSED MERCHANDISE SOLD BY
AUTHORIZED YAMAHA AUDIO DEALERS IN CANADA, AND SUBJECTED TO NORMAL
CONSUMER USE, BY THE ORIGINAL PURCHASER.
7. This warranty does not apply to Yamaha Canada Music Ltd. audio products sold in Saskatchewan,
and to which statutory warranties contained in The Consumer Products Warranties Act, 1977
(Saskatchewan) are applicable.
8. This warranty is void where prohibited by law.
~
~
m
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
i
~
~
.·
~
"""
~
~
m
~
~
Factory Service Centres are located at:
135 Milner Avenue, Scarborough, Ontario, M1 S 3R1.
(416)298-1311
~
~
~
~
For the location of other service centres, contact any Yamaha Audio Dealer or one of
the above.
~
~
~
A WARRANTY REGISTRATION CARD IS NOT REQUIRED.
~
~~
PLEASE KEEP YOUR BILL OF SALE AS PROOF OF PURCHASE SHOULD WARRANTY REPAIRS BE
REQUIRED.
W VAMAHA
~ 1j
t~
~t~r~~~~t~~t~~t~~~~~~~t~~
.
.
~
~
~
ti~~~~~~~~~ni~~~~~~~~~~
010394
WT55060
.YAMAHA
LIMITED WARRANTY ON
HOME AUDIO PRODUCTS
Thank you for selecting a YAMAHA product. YAMAHA products are designed and manufactured to provide a high level of defect-free performance. Yamaha
Corporation of America ("YAMAHA") is proud of the experience and craftsmanship that goes into each and every YAMAHA product. YAMAHA sells its
products through a network of reputable, specially authorized dealers and is pleased to offer you, the Original Owner, the following Limited Warranty, which
applies only to products that have been (1) directly purchased from YAMAHA's authorized dealers in the USA, including Puerto Rico (the "Warranted Area")
and (2) used exclusively in the Warranted Area. YAMAHA suggests that you read the Limited Warranty thoroughly, and invites you to contact your authorized
YAMAHA dealer or YAMAHA Customer Service if you have any questions.
THIS WARRANTY COVERS THE LISTED PRODUCTS AGAINST DEFECTS IN MATERIALS OR
WORKMANSHIP FOR THE NUMBER OFYEARS IDENTIFIED BELOW.
Warranty Term
Duration of Warranty from Date of
Purchase by or for the Original Owner
Type of Product
AN and Stereo Receivers, Processor and Integrated Amplifiers,
Separate Amplifiers and Preamplifiers, Tuners, CD Players and
Changers, HOD Players and Recorders, Network Players, Powered
Loudspeakers, Media Controllers and Speaker Systems purchased
individually, as a pair, or as part of an Integrated or Packaged System.
........................ 2 years
Cassette Decks, Btu-ray Disc Players, DVD Players and Changers,
Integrated Systems (Receiver or Amplifier combined or on same
chassis with CD, DVD or Btu-ray Disc Player}, Desktop Audio Systems
(i.e. TSX and POX Series}, Multimedia Speakers, Headphones,
Earphones and Accessories.
........................ 1 year
Coverage: YAMAHA will, at its option, repair or replace the product covered by this warranty if it becomes defective, malfunctions or otherwise fails to
conform with this warranty under normal use and service during the term of this warranty, without charge for labor or materials. Repairs may be
performed using new or refurbished parts that meet or exceed YAMAHA specifications for new parts. If YAMAHA elects to replace the product, the
replacement may be a reconditioned unit. You will be responsible for any installation or removal charges and for any initial shipping charges if the
product(s) must be shipped for warranty service. However, YAMAHA will pay the return shipping charges to any destination within the USA if the repairs
are covered by the warranty. This warranty does not cover (a) damage, deterioration or malfunction resulting from accident, negligence, misuse, abuse,
improper installation or operation or failure to follow instruGtions according to the Owner's Manual for this product; any shipment of the product (claims
must be presented to the carrier); repair or attempted repair by anyone other than YAMAHA or an authorized YAMAHA Service Center; (b) any unit which
has been altered or on which the serial number has been defaced, modified or removed; (c) normal wear, battery or battery replacement and any periodic
maintenance; (d) deterioration due to perspiration, corrosive atmosphere or other external causes such as extremes in temperature or humidity; (e)
damages attributable to power line surge or related electrical abnormalities, lightning damage or acts of God; (f) RFI/EMI (Interference/noise) caused by
improper grounding or the improper use of either certified or uncertified equipment, if applicable; or (g) interference arising from the use of wireless
communication devices (e.g. 2.4 gHz cordless telephones), or other radio frequency emitting products such as microwave ovens, whether such
interference impairs the operation of the product or vice-versa. Consult the Owner's Manual for guidance on set-up procedures for minimizing the risks of
interference. Any evidence of alteration, erasing or forgery of proof-of-purchase documents will cause this warranty to be void. This warranty covers only
the Original Owner and is not transferable.
In Order to Obtain Warranty Service: Warranty service will only be provided for defective products within the Warranted Area. Contact your
local authorized YAMAHA dealer who will advise you of the procedures to be followed. If this is not successful , contact YAMAHA at the address,
telephone number or website shown below. YAMAHA may request that you send the defective product to a local authorized YAMAHA Servicer or
authorize return of the defective product to YAMAHA for repair. For products requiring in-home service, contact your local authorized Yamaha dealer to
arrange for service. If you are uncertain as to whether a dealer has been authorized by YAMAHA, please contact YAMAHA's Service Department at the
number shown below, or check Yamaha's website at http://usa.yamaha.com. Product(s) shipped for service should be packed securely and must be
accompanied by a detailed explanation of the problem(s) requiring service, together with the original or a machine reproduction of the bill of sale or other
dated, proof-of-purchase document describing the product, as evidence of warranty coverage. Should any product submitted for warranty service be
found ineligible therefore, an estimate of repair cost will be furnished and the repair will be accomplished only if requested by you and upon receipt of
payment or acceptable arrangement for payment.
Limitation Of Implied Warranties and Exclusion Of Damages: ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE APPLICABLE PERIOD OF TIME SET
FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR DAMAGES BASED UPON
INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE OR INTERRUPTION OF
PERFORMANCES OR ANY CONSEQUENCES. YAMAHA'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT
OF THE PRODUCT, AT YAMAHA'S OPTION . SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. This Warranty gives you specific legal rights, and you may also have other rights which vary from stale to stale. This is the only express
warranty applicable to the product specified herein; Yamaha neither assumes nor authorizes anyone to assume for it any other express warranty.
If you have any questions about service received or if you need assistance in locating an authorized YAMAHA Servicer, please contact:
.YAMAHA
CUSTOMER SERVICE
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, California 90620-1373
Telephone: 800-292-2982
http://usa.yamaha.com
Do not return any product to the above address without a written Return Authorization issued by YAMAHA.
©201 2 Yamaha Corporation of America
04/2012 ZE38290
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising