war - AV Ace
Eamon
BL B CTU ROTNTITC S§
MPC-5050Plus
PORTABLE MP3/CD PLAYER
RADIO CASSETTE RECORDER
WITH USB INPUT
INSTRUCTION MANUAL
Warnings and Precautions
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture
AVERTISSEMENT: Pour réduire le risque d’incendie
ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
CAUTION: Use of any controls or adjustments or per-
formance of procedures other than those herein specified
may result in hazardous radiation exposure.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for com-
pliance could void the user’s authority to operate the
equipment ^
WARNING: Do not place the unit on top of any soft, po-
rous, or sensitive surfaces to avoid damaging the surface.
Use a protective barrier between the unit and surface to
protect the surface,
WARNING: Use of this unit near fluorescent lighting
may cause interference regarding use of the remote. If
the unit is displaying erratic behavior move away from
any fluorescent lighting, as it may be the cause.
CAUTION: Danger of explosion if battery is incorrectly
replaced, Replace only with the same or equivalent type.
PRECAUTION: Danger d explosion si les piles sont
remplacées de fagon incorrect. Remplacer les piles seule-
ment par le méme type de pile ou l'equivalent
WARNING: There is a danger of explosion if you at-
tempt to charge standard Alkaline batteries in the unit.
Only use rechargeable NiMH batteries.
WARNING: The remote control’s button cell battery
contains mercury. Do not put in the trash, instead recycle
or dispose of as hazardous waste
WARNING: Lithium batteries, like all rechargeable
batteries are recyclable and should be recycled or dis-
posed of in normal household waste. Contact your local
government for disposal or recycling practices in your
area. They should never be incinerated since they might
explode.
WARNING: Shock hazard - Do Not Open
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS
OUVRIR
Mains plug is used as disconnect device and it should
remain readily operable during intended use. In order
to disconnect the apparatus from the mains completely,
the mains plug should be disconnected from the mains
socket outlet completely.
La prise du secteur est utilisé pour déconnecter le
système,
La prise du secteur ne doit pas être obstruée ou doit être
Jacilement accessible pendant son utilisation. Pour être
complètement déconnecté de l’alimentation d'entrée, la
prise doit être débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or recharge-
able (ni-cad, ni-mh, etc) batteries.
No mezcle baterias viejas y nuevas
No mezcle baterias alcalinas, eständar (carbono-zinc) o
recargables (ni-cad, ni-mh, elc.).
CAUTION WARNING: TO REDUCE THE RISK OF
RISK OF ELECTRIC SHOCK ELECTRIC SHOCK, DO NOT REMOVE
"E COVER (OR BACK). NO USER-
ATTENTION SERVICEABLE PARTS INSIDE. REFER
Ea SERVICING TO QUALIFIED SERVICE
Me PERSONNEL.
— на Z ZÉ£>=Zn. —— — a
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons
The exclamation point within an equilatera! triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the |Herature meca yb the
appliance
This product utilizes a Class 1 laser to read
Compact Discs. This laser Compact Disc Player is
equipped with safety switches to avoid exposure
when the CD door is open and the safety interlocks
are defeated. Invisible laser radiation is present
when the CD Player's lid is open and the system’s
interlock has failed or been defeated. It is very
important that you avoid direct exposure to the
laser beam at all times Please do not attempt to
defeat or bypass the safety switches
General
Power supply:
Qutput Power:
Speaker:
AUX/MP3 in:
Dimensions:
Weight:
Operation Temperature:
General
Frequency:
Antenna:
CD
Optical pick-up lens:
Specification
AC 110V / 60HZ
DC 9V (Uses 6 pcs of “UM-1" size battery)
1.0 watts x 2 (RMS)
90mm Cone type
3.5mm jack
24 x 21 x 13cm (L x D x H)
2.4 kgs
+5 °C - +35 °C
AM: 520 — 1710 KHz
FM: 87.5 — 108 MHz
AM: Built-in Ferrite Bar
FM: Antenna Rod
3 beam semiconductor laser
10
Cassette Operation Important Safety Instructions
1. Read these Instructions
| FCC Warnings
2. Keep these Instructions
RECORDING FROM DISCS NOTE: This equipment has been tested and found to comply with
1. Select the FUNCTION switch to "CD/MP3" position. 3, Heed all Warnings the limits for a Class B digital device, pursuant to Part 15 of the
2. Press the OPEN button to open the CD door. FCC Rules. These limits are designed to provide reasonable protec-
4. Follow all instructions. tion against harmful interference in a residential installation. This
3. Load a CD with label side upward the CD compartment and ciose the CD door and the player plays all equipment generates, uses, and can radiate radio frequency energy
the tracks once {continuous Play) 5. Do not use this apparatus near water. and, if not installed and used in accordance with the instructions,
4. Press the STOP button to stop olavina the CD. | may cause harmful interference to radio communications. However,
( = ) ue 6. Clean only with a dry cloth there is no guarantee that interference will not occur in a particular
5. Insert the cassette into the Cassette Compartment. installation. If this equipment does cause harmful interference to
6. Press the PAUSE button. 7. Do not block any ventilation openings, Install in accor- radio or television reception, which can be determined by turning
7. Press the RECORD button dance with the manufacturer’s instructions the equipment off and on, the user is encouraged to try to correct
| the interference by one or more of the following measures:
8. Press the play/pause button ( Mil ) to start playing. 8. Do not install near any heat sources such as radiators,
9. Release the PAUSE button to begin recording. You can also record audio signal from exteranl heat registers, stoves, or other apparatus (including * Reorient or relocate the receiving antenna.
microphone. ; amplifiers) that produce heat * Increase the separation between the equipment and receiver
» Connect th ipment into an outlet ircuit different fi
10. Adjust the VOLUME, if necessary. | po e, e UU OT
9, Do not defeat the safety purpose of the polarized or er 1s connecleds |
11. To stop recording, press STOP/EJECT button. When the tape operate to the end recording will be stop . . * Consult the dealer or an experienced radio/TV technician for
| ET grounding - type plug. A polarized plug has two blades pen
atilomaticaliys with one wider than the other, A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. = bi TEE
| | rnin |
RECORDING FROM THE BUILT IN RECORDING MICROPHONE When the provided plug does not fit into your outlet, | Additional Warnings ee dE
1. Select the RUNES, switch to Tape (Radio off) position. consult an electrician for replacement of the obsolete * The apparatus shall not be exposed to dripping or splashing and
2. Insert a cassette tape into the Cassette Compartment, outlet, that no objects filled with liquids, such as vases, shall be placed
3. To avoid feedback between the speaker and the built in recording microphone, set the Volume Control in on apparatus
the minimum position 10. Protect the power cord from being walked on or L'appareil ne doit pas être exposé aux écoulements ou aux écla-
4. P he R db | pinched particularly at plugs, convenience receptacles, boussures et aucun objet ne contenant de liquide, te! qu'un vase,
ress the Record button. and the point where they exit from the apparatus ne doit être placé sur l'objet
5. Recording can be achieved via built in microphone. |
6. To stop recording, press Stop/Eject button. When the tape operate to the end, recording will be stop 11. Only use attachments/accessories specified by the * Main plug is used as disconnect device and it should remain
manufacturer. readily operable during intended use. In order to disconnect the
automatcially. apparatus from the mains completely, the mains plug should be
— disconnected form the mains socket outlet completely.
12 Use only with a cart, stand, tripod, brack- La prise du secteur ne doit pas étre obstruée ou doit être facile-
et, or table specified by the manufacturer ment accessible pendant son utilisation. Pour étre complétement
>
or sold with the apparatus. When a cart is déconnecté de l'alimentation d'entrée, la prise doit être débran-
. | chée du secteur.
used, use caution when moving the cart/
appar atus combination to avoid injury Battery shall not be exposed to excessive heat such as sunshine,
H e а o e A e from tip-over. fire or the like
Les piles ne doivent pas être exposées à de forte chaleur, tel qu'à
la lumière du soleil, au feu ou autres choses de semblable
13. Unplug this apparatus during lightning storms or when
unused for long periods of time,
Turn the unit volume to minimum before you connect your headphone to headphone jack. Headphones
*
Caution marking is located at the rear or back of the apparatus
Attention marquage es! situé à l'arrière ou à l'arrière de
l'appareil
should have a 3.5 mm diameter stereo plug and an impedance of 8-32 ohms. When headphones are
14. Refer all servicing to qualified service personnel. Ser-
connected, the speakers are automatically get disconnected vicing is required when the apparatus has been dam-
NOTE: Extended listening of music at high volume may damage your hearing. It is highly recommended to aged in any way, such as power-supply cord or plug is * The marking information is located at the rear or back of ap-
use at comfortable volume levels, damaged, liquid has been spilled or objects have fallen paratus
into the apparatus, the apparatus has been exposed to Les informations de marquage est situé à l'arrière ou à l'arrière
rain or moisture, does not operate normally, or has been de l'appareil
dropped.
This symbol indicates that this product
[] incorporates double insulation between
hazardous mains voltage and user
accessible parts
Connecting the Power
AC POWER OPERATION
Before connecting the unit to an AC Outlet, check that the operating VOLTAGE of the unit is identical with the
VOLTAGE of your Local Power Supply.
Connect the supplied AC Power Cord to the AC Socket at the back of unit
When the AC Power Cord is plugged into the Batteries are automatically disconnected.
BATTERY OPERATION
The unit cannot be operated by battery when the AC power cord is connected.
Open the battery cover and put the batteries as indicated inside the battery compartment.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the batteries
compartment.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh
ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow
battery manufacturer's directions)
INSTALLING THE REMOTE CONTROL BATTERY E à | Ed
| 1
1. Remove the battery compartment cover on the back of К С 4 A or OPEN
the remote control, by pushing the tab to the right while ee
removing the cover. | ¡PUSH
2. Insert a 3V lithium battery (CR2025 or equivalent)
following the polarity (+) as shown on the diagram inside the compartment.
3. Replace the battery compartment cover.
Note: The remote control battery normally lasts for about one year, although it depends on how often the
remote control is used.
If the remote control is not working properly, replace the battery.
PRECAUTIONS WHEN USING BATTERIES
1. CAUTION: Danger of explosion if battery is not inserted correctly. Replace only with the same or
equivalent type.
2, Do not mix different types of battery together (e.g. alkaline, rechargeable and standard (carbon zinc) or
old batteries with fresh ones.
3. Exhausted batteries must be removed to prevent possible leakage
4, Dispose of batteries properly in accordance with the environmental regulations in force.
Cassette Operation
PLAYBACK
1. Select the FUNCTION switch to the "TAPE" position.
Insert the cassette into the Cassette Compartment.
Press the PLAY button to play a tape loaded.
Adjust the VOLUME, if necessary.
Press the STOP/EJECT button to stop the tape play.
*PAUSE button is used for temporarily stopping the tape during recording or playback.
по коем
FAST WINDING
1. To fast forward or rewind, press Fast Forward or Rewind button.
2. Press the STOP/EJECT button to stop fast winding as the tape ended, in order to prevent damage to the
cassette tape
CASSETTE RECORDER OPERATION
RECORDING
Within Recording, no volume adjustment is necessary, recording leve! is automatically set.
CASSETTE TAPE SELECTION
The quality and condition of the cassette tapes used will have a direct effect on the performance of this unit.
Low quality tapes tend to break and stretch, and a broken tape can easily become en-tangled in the drice
mechanism, causing major damage. Stretched tapes will run at un-even speeds and will distort anything
recorded on them.
Use only well-known brands of tape.
« Use of C-120 (120 minutes) cassettes is not recommended. The extreme thinness of this tape may result
in breakage or other problem.
Check to ensure there are no loose layers of tape visible through the cassette center windows. Tighten
these loose layers with a pencil or ball-point pen before inserting the cassette into the unit
RECORDING FROM THE BUILT-IN RADIO
Select the FUNCTION switch to "Radio" position.
Set the Band switch to the desired band position
Turn in desired radio station.
Insert the cassette into the Cassette Compartment.
Press the PAUSE button,
Press the RECORD button.
Release the PAUSE button to begin recording.
Adjust the VOLOUME, if necessary
To stop recording, press STOP/EJECT button. When the tape operate to the end recording will be stop
automatically.
оо моло >
To Repeat One Track on Music
CD or MP3 Disc or USB
1. During CD/MP3 disc or USB playback,
press SKIP FORWARD b»I / SKIP
BACKWARD Hd buttons to select a
track you wish to repeat.
2. Press the MODE button until the
“REP” indicator shows on LCD
display. The unit will play the
desired track repeatedly.
3. To cancel the setting, press the
MODE button continuously until the
“REP” “REP ALL” “RANDOM”
“ALBUM” indicators disappear.
To Repeat the Entire Disc or USB
1. During CD/MP3 disc or USB playback,
press the MODE button continuously
until the “REP ALL” indicator shows
on LCD display. The unit will play all
tracks on the disc repeatedly.
2. To cancel the setting, press the MODE
button continuously until the “REP”
“REP ALL” “RANDOM” “ALBUM”
indicators disappear.
To Play Music CD or MP3 Disc
or USB Randomly
1. During CD/MP3 disc or USB playback,
press the MODE button continuously
until the “RANDOM” indicator shows
on LCD display. The unit will play all
tracks randomly.
2. To cancel the setting, press the MODE
button continuously until the “REP”
“REP ALL” “RANDOM” “ALBUM”
indicators disappear.
To Repeat Album for MP3 Disc
or USB
1. During MP3 disc or USB playback,
press the MODE button continuously
until the “ALBUM?” indicator shows
display. The unit will play all desired
on LCD folder (album) repeatedly.
2. To cancel the setting, press the
MODE button continuously until
the “REP” “REP ALL” “RANDOM”
“ALBUM” indicators disappear.
NOTES:
Repeat album function cannot support
normal music CD.This function is for
MP3 disc format only.
To Program Specific Tracks (up to 20
Tracks)
1. Load the CD or USB you wish to program.
2. Make sure the CD or USB is in stop mode.
3. Press the MODE button once, "PO1" will
display on the LCD and "PROG" indicator
will blink
4. Press the SKIP FORWARD bl /
SKIP BACKWARD l«« buttons
until the desired track number is
reached.
5. Press the MODE button to store the
selection.
6. Repeat the (4) & (5) steps until you
have entered all the tracks.
7. To play the stored sequence, press the
PLAY/PAUSE button.
8. After all memory tracks have been
played, the CD player will stop
automatically.
NOTES:
When 20 tracks of CD (or 99 tracks for
MP3 disc or USB) have been programmed,
the memory is full and “FUL” will appear
on the display. If you want to cancel the
program memory, press the STOP button
once. “REP” “REP ALL” also applies to
CD, MP3 disc or USB program playback.
To Repeat Programmed tracks
1. During program play, press Mode
button once will repeat the specifically
programmed track.
2. Press Mode button again will repeat all
the programmed track.
3. Press Stop button to cancel repeat play on
programmed tracks.
Location of Controls
PHONES
|
BAND SWITCH В
=
BATTERY AC SOCKET
COMPARTMENT
MP3 USB
= A a A BATT) Si
PHONES -
ki |
VOLUME ==
hil À
BASS (ON/OFF)
a В
FAST | PLAY
FWD
STOP/ BACH RECORD
БЕСТ FWD
FUNCTION SWITCH
TUMMING SCALE
TUNNING
USB
SLOT-IN
Listening to Radio
1.
Insert the main plug into a main supply
power outlet.
2. Select the FUNCTION switch to
RADIO position.
3. Slide the BAND switch to select AM /
FM ST band.
4. Rotate the TUNING control knob to
search for the desire station.
5. Rotate the VOLUME control knob to
the desire volume sound. я
6. To turn off the unit power, select the
FUNCTION switch to OFF
position.
NOTES:
To have the best AM reception, slightly
rotate the unit or move the unit to a
different area of the room until the best
reception is obtained.
To obtain the best FM reception, fully
extend the FM antenna. Avoid close
proximity to the speakers and other
electrical appliance.
Listening to Music CD or MP3 Disc
1. Insert the main plug into a main
supply power outlet.
2. To open the CD door by lifting the
Open/Close area near the CD door.
Insert disc into the disc compartment
with the title side upwards.
3. Close the CD door, select the
FUNCTION switch to CD position,
“-—" 1s displayed for few seconds, and
total number of tracks will show on the
LCD display.
4. Press the PLAY/PAUSE button to
play the CD.
5. Press SKIP FORWARD b»l / SKIP
BACKWARD Hed buttons to jump to
next or previous track.
6. Press and hold SKIP FORWARD PI /
SKIP BACKWARD << buttons to search
rapidly within a track to locate a specific
passage.
7. During CD play, press the
PLAY/PAUSE button to pause CD
playing and press again to resume.
8. During MP3 playback, press and hold
the FOLDER UP button to search for
next folder.
9. Press the STOP button to stop the CD
playing.
10. After all tracks have been played, the
CD player will stop automatically.
NOTES:
Do not open the CD compartment while
the disc is playing or rotating. First press
the STOP button.
This unit can play Music CD & MP3
Disc format.
Listening to music on USB
1. Insert the mains plug into a power
supply outlet.
2. Plug the mass storage USB into the
USB socket. Slide the FUNCTION
switch to CD/USB position; "---" is
displayed for few seconds. Total
number of tracks and USB indicator
will then show on the LCD display.
3. Press PLAY/PAUSE button to play
the track on the USB.
4. Press SKIP FORWARD PM or SKIP
BACKWARD Ht button to search
rapidly within a track to locate a
specific passage.
5. During USB play, press the PLA Y/
PAUSE Pll button to pause USB play
and press again to resume.
6. During playback, press the FOLDER+
button to skip to next folder.
7. During playback, press the FOLDER—
button to skip to previous folder.
8. Press the STOP button to stop the USB
play.
9. After all tracks have been played, the
USB player will stop automatically.
NOTES:
a) When CD disc is loaded inside the disc
compartment, press and hold the CD--
USB button for more than 1 sec. to
select USB operation.
b) This unit can play disc of MP3 format.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising