9420 〉〉 l-band / if-band rf-fiber transmitter and receiver - AV-iQ

9420 〉〉 l-band / if-band rf-fiber transmitter and receiver - AV-iQ
9420 〉〉 L-BAND / IF-BAND RF-FIBER TRANSMITTER AND RECEIVER
The 9420-Series of linear RF-Fiber (E-O) Transmitter and linear Fiber-RF (O-E) Receiver SATCOM
Fiber Optic Link Cards provides an easily integrated openGear® solution for a fiber optic link
between an LNB and an IRD. With models specifically optimized for L-band and IF-band linear
RF communications, the card combination of fiber transmitter and receiver allows up to 30 km
of transport length. The cards fit our standard 20-slot frames and utilize blind mate connection
beween the card and its rear module, allowing card installation without requiring rear access to
the frame or its connections.
The 9420 transmit (Tx) cards offer Smart Gain to help provide stable gain control in the presence
of varying input signal levels. This helps maintain constant operating power in these conditions.
Full user DashBoard™ remote control allows full status and control access locally or across a
standard Etherenet network.
〉〉 FEATURES
Models specifically optimized for L-Band and IF-band
signals
One-button Peak Optimizer allows quick and easy
set-up
Tx / Rx RF power monitoring via DashBoard, card-edge
LEDs, monitoring ports, and SNMP
Supports up to 30 km links
SmartGain provides enhanced AGC performance
Blind mate rear module connections allow card installation without requiring rear frame access
Optically-Isolated DFB Lasers enable high-dynamicrange links
LNB power sourcing – LNB power can be enabled or
disabled as desired
Five year warranty
25 dB Tx and Rx adjustable gain range
Combined E-O Tx (9420LT) and O-E Rx (9420LR) L-Band Fiber Optic Link
Enhanced
AGC
Manual Gain
Control
RF (Elect) In
(from SAT LNB)
Ethernet 10/100
(On Frame)
LNB
DC On/Off
Gain
Cntrl
RF > Optical
Converter
DashBoard™/OGCP
Monitor/Control
Fiber
Transport
Fiber (Optical) Out
Input Monitor Out
Manual Gain
Control
Fiber (Optical) In
Ethernet 10/100
(On Frame)
9420LT
Optical > RF
Converter
Gain
Cntrl
DashBoard™/OGCP
Monitor/Control
DA
RF (Elect) Out
(to IRD)
Input Monitor
Out or
RF (Elect) Out
9420LR
〉〉 SPECIFICATIONS
9420 RF-FIBER (E-O) TRANSMITTER CARDS
Power
12 Watts.
Input/Outputs
Inputs: (1) 75Ω RF input; 850-2300 MHz (L-band) with
LNB DC power inject enable/disable
Outputs: (1) Fiber Optic (LC-APC or SC-APC terminations). (1) Monitor port 75Ω.
Fiber Wavelength: 1310, 1550 nm
Performance
Fiber Transport Length: up to 30 km
Optical Output Power: 5 ±2 dBmo
Frequency Range:
(L-Band) 850-2300 MHz
(IF-Band) 50-1000 MHz
Input Return Loss (minimum): 10 dB
Total Front-End RF Gain(1) (at minimum attenuation
setting): 25 ±2 dB
Attenuation Adjustment Range: 30 dB
Spurs Free Dynamic Range(2): 98 dB-Hz
Noise Figure (at maximum gain, 25°C): 23 dB
Input IP3 (at maximum gain, 25°C): -4 dBm
Total RF Power Into Laser: 2 ±2dBm
1. Link RF Gain dB = TG + RG - 2*Fiber Loss dBo
2. SFDR = 2/3*(IIP3 + 174 - NF).Power
COBALTDIGITAL.COM
9420 FIBER-RF (O-E) RECEIVER CARDS
Power
12 Watts
Input/Outputs
Inputs: (1) Fiber Optic; LC-APC or SC-APC terminations.
Outputs: (1) 75Ω RF input; 850-2300 MHz (L-band).
(1) Monitor port 75Ω.
Fiber Wavelength: 1310, 1550 nm
Performance
Output Return Loss (Minimum): 10 dB
Total Front-End RF Gain(1) (at minimum attenuation
setting): 20 dB (dual output mode); 25 dB (single
output mode)
Attenuation Adjustment Range: 15 dB
Output IP3 (at maximum gain, 25°C): 20 dB (dual
output mode); 25 dB (single output mode)
1. Link RF Gain dB = TG + RG - 2*Fiber Loss dBo
US SALES 800 669-1691 / DIRECT +1 217-344-1243 / SALES@COBALTDIGITAL.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. E. & O.E. ©2014 COBALT DIGITAL INC.
9420 〉〉 L-BAND / IF-BAND RF-FIBER TRANSMITTER AND RECEIVER
9420 Rear I/O Module Connectorization
NC
NC
NC
NC
OPTICAL IN
OPTICAL IN
NC
RF OUT
NC
RF OUT
NC
RF OUT/MON
NC
RF OUT/MON
All 9420 cards use a passive blindmate rear module. The same rear module is used for all card models.
The rear module is a "split" type and can accommodate up to two cards per rear module. The connections
are determined by the card(s) installed and are as shown below.
Dual RF-to-Fiber
Tx (2x E-O)
Single RF-to-Fiber
Tx (E-O)
RM20-9420-LC-BNC-50
RM20-9420-LC-BNC-75
RM20-9420-SC-BNC-50
RM20-9420-SC-BNC-75
Single Fiber-to-RF
Rx (O-E)
RM20-9420-LC-SMA-50
RM20-9420-SC-SMA-50
Note: Rear modules are equipped with a slot blocker preventing two Tx cards from
being fitted to the same rear module. This accommodates limited per-slot power
capacity for earlier frames such as the 8321. For OG3-FR and HPF-9000 frames,
this blocker can be removed with no restrictions on dual-card installation for a
given rear module.
Rear Modules shown are applicable for all card models. Example I/O shown here
is a function of card(s) fitted to the rear module. Refer to Rear I/O Module Single
and Dual-Card Tx/Rx Combinations for depictions of various I/O complements.
Fiber
RF
RF-to-Fiber / Fiber-to RF
Tx/Rx (E-O O-E)
Dual Fiber-to-RF
Rx (2x O-E)
〉〉 ORDERING INFORMATION
Note: Dual Tx installation for a rear module (two adjacent slots
served by a shared rear module) is not compatible using limitedpower frame such as the 8321. This frame can only accommodate
one Tx, one Rx, or two Rx cards per rear module/slot pair. This
restriction does not apply if using an HPF-9000 or OG3-FR frame.
9420-LT13 L-Band (850 MHz - 2.3 GHz) RF-Fiber
Optic Transmitter; 1310nm DFB Tx @ +5dBm
9420-LT15 L-Band (850 MHz - 2.3 GHz) RF-Fiber
Optic Transmitter; 1550nm DFB Tx @ +5dBm
9420-LR L-Band (850 MHz - 2.3 GHz) Fiber-RF
Optic Receiver
9420-IFT13 IF-band (40 MHz - 1 GHz) RF-Fiber
Optic Transmitter; 1310nm DFB Tx @ +5dBm
9420-IFT15 IF-band (40 MHz - 1 GHz) RF-Fiber
Optic Transmitter; 1550nm DFB Tx @ +5dBm
9420-IFR IF-Band (40 MHz - 1 GHz) Fiber-RF Optic
Receiver
COBALTDIGITAL.COM
9420-LTCWDM-XX L-Band (850 MHz - 2.3 GHz)
RF-Fiber Optic Transmitter; CWDM wavelength DFB
Tx @ +5dBm. Replace "XX" with desired CWDM
wavelength when ordering. See table below for
available CWDM wavelengths.
9420-IFTCWDM-XX L-Band (40 MHz - 1 GHz)
RF-Fiber Optic Transmitter; CWDM wavelength DFB
Tx @ +5dBm. Replace "XX" with desired CWDM
wavelength when ordering. See table below for
available CWDM wavelengths.
Note: The receiver cards listed above work with any respective
L-Band or IF-Band CWDM transmitter card.
-27: 1270nm -29: 1290nm -33: 1330nm
-35: 1350nm -37: 1370nm -39: 1390nm
-41: 1410nm -43: 1430nm -45: 1450nm
-47: 1470nm -49: 1490nm -51: 1510nm
-53: 1530nm -57:
1570nm -59: 1590nm
-61: 1610nm
Note: Rear I/O Modules are blindmate type and vary only in connector type and Zo as shown below. Rear I/O Module RF and fiber
connection population and function is determined by card.
RM20-9420-LC-BNC-50 20-slot Frame Rear I/O
Module (Standard Width; Split) 50Ω BNC, LC-APC
Fiber Connectors. Supports 2 Cards.
RM20-9420-LC-BNC-75 20-slot Frame Rear I/O
Module (Standard Width; Split) 75Ω BNC, LC-APC
Fiber Connectors. Supports 2 Cards.
RM20-9420-LC-SMA-50 20-slot Frame Rear I/O
Module (Standard Width; Split) 50Ω SMA, LC-APC
Fiber Connectors. Supports 2 Cards.
RM20-9420-SC-BNC-50 20-slot Frame Rear I/O
Module (Standard Width; Split) 50Ω BNC, SC-APC
Fiber Connectors. Supports 2 Cards.
RM20-9420-SC-BNC-75 20-slot Frame Rear I/O
Module (Standard Width; Split) 75Ω BNC, SC-APC
Fiber Connectors. Supports 2 Cards.
RM20-9420-SC-SMA-50 20-slot Frame Rear I/O
Module (Standard Width; Split) 50Ω SMA, SC-APC
Fiber Connectors. Supports 2 Cards.
US SALES 800 669-1691 / DIRECT +1 217-344-1243 / SALES@COBALTDIGITAL.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. E. & O.E. ©2014 COBALT DIGITAL INC.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising