vector seating system
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
MATERIALS INCLUDED
epoxy
a
b
TOOLS NEEDED
c
ratchet
steel
wire brush
pencil
7/32" hex bit for
tamper-resistant
screws
1/4", 1/2" & 3/4" drill
bits for concrete
tape measure
hammer drill
epoxy gun
STEP BY STEP FOR VECTOR SEATING SYSTEM TRI-HUB CONFIGURATION
Place bench, top down
Attach legs
Position bench
• Securely place bench, top down, on top
of a padded surface.
• Position leg with edge of bench seat.
• Insert 3/8"-16 x 3/4" tamper-resistant
button head cap screw (b) into mounting
holes in bench and thread into holes
using provided 7/32" hex bit for tamperresistant screws.
• Carefully turn bench right side up; you
will need another person to hold the
bench and/or a sturdy box to provide
support until benches are attached; they
will not stand alone. Use padding where
necessary.
• Repeat with all benches ensuring
that end/intermediate legs are used
appropriately.
• Position bench in desired location. Be
sure that the space allows enough room
for full configuration.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 4 | Rev. 06-18-15
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
STEP BY STEP FOR VECTOR SEATING SYSTEM TRI-HUB CONFIGURATION
4
5
6
Bottom view
Bottom view
Attach second 120º bench
Attach third 120º bench
Mark surface mount location
• Position the two benches so that
connection holes align.
• Position the third bench so that the
conneciton holes align.
• Once connection holes are aligned
insert 3/8"-16 x 3/4" tamper-resitant
button head cap screw (b) into bench
connection holes using provided 7/32"
hex bit for tamper resistant screws.
• Once connection holes are aligned
insert 3/8"-16 x 3/4" tamper-resitant
button head cap screw (b) into bench
connection holes using provided 7/32"
hex bit for tamper resistant screws.
• Once module is in the desired location,
mark the ground along the inside of each
leg including the center notch, indicated by
the dashed line.
Note: Although two benches are
connected they will not stanalone until
the third bench is completely attached.
You will still need a person and/ or sturdy
box to support the configuration after this
step.
• Carefully move bench to the side once
mounting surfaced is marked.
Note: If the Tri-hub is surface mounted
continue on to step 6, otherwise
installtion is complete.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 4 | Rev. 06-18-15
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
STEP BY STEP FOR VECTOR SEATING SYSTEM TRI-HUB CONFIGURATION
8
7
9
Side view of surface mount plate
11 1/8"
1/8”
Top view
11 1/8"
1/8”
Position surface mount plate
Drill holes
Fill holes & insert anchors
• Measure and mark 1 1/8" from surface
mount mark to find the surface mount
plate center line, indicated by the dashed
line.
• Use hammer drill to drill 4.5" deep x 3/4"
diameter anchor hole at each marked
location using a 3/4" drill bit suitable for
concrete drilling.
• Use compressed air and steel wire brush
to clean each anchor hole in accordance
with epoxy instructions.
• Position the surface mount plate by first
aligning the center notch with the center
notch line.
Note: Forms+Surfaces recommends
starting holes with 1/4" diameter drill
bit followed by 1/2" and finally 3/4" for
maximum accuracy.
• Next, align the mounting holes and
positioning notches to the surface mount
plate center line.
• Mark the center of each mounting
hole. • Use epoxy in epoxy gun to fill each
anchor hole 5/8 of the hole depth in
accordance with epoxy instructions
• Insert 3/8"-16 x 4-1/4" epoxy anchor
(a) into each anchor hole so anchor top
is flush with ground. Allow proper curing
time according to cure schedule on
epoxy instructions before moving on to
Step 10.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 4 | Rev. 06-18-15
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
STEP BY STEP FOR VECTOR SEATING SYSTEM TRI-HUB CONFIGURATION
12
10
11
Attach surface mount plate
Fit module onto surface mount plate
Attach leg to surface mount plate
• Position surface mount plate so that
mounting holes line up with anchors.
• Lift module up and slide leg(s) onto
mounted surface mount plate(s).
• Ensure that leg mounting hole and
surface mount plate mounting hole align.
• Insert 3/8”-16 x 1-1/2” tamper-resistant
button cap screws (c) into mounting
holes in surface mount plate.
• Insert 3/8"-16 x 3/4" tamper-resitant
button head cap screw (b) into bench
connection holes using provided 7/32"
hex bit for tamper resistant screws.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 4 of 4 | Rev. 06-18-15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising