Feature Specification Setup and Function How to set the Camera RS

Feature Specification Setup and Function How to set the Camera RS
Feature
1
Setup and Function
2
■ 1/3" SONY SuperHAD CCD Ⅱ (960H) (Min. Illumination)
■ Privacy Masking(8 Zone Selectable)
■ DPC (Dead Pixel Compensation)
④
■ HLC (High Light Compensation)
■ Lens Shading
■ 2DNR
③
①
②
■ Motion Detection(4 Zone Selectable)
⑥
■ Multi Language
■ DWDR
■ ICR TDN
⑤
Specification
Item
Specification
① Function Set Up Button
1/3" SONY Super HAD CCD Ⅱ (960H)
Imaging Sensor
Signal System
- SET Button : Displays the menu on the screen. Press the button to confirm status or
1028(H) X 508(V)
1028(H) X 596(V)
976(H) X 494(V)
976(H) X 582(V)
Scanning System
after changing a selected item.
2:1 Interlace
H:15.734 ㎑ / V:59.94 ㎐
Scanning Frequency
S/N Ratio
- Up and Down Button : Used to move the cursor up or down in the menu screen to select
H:15.625 ㎑ / V:50 ㎐
a desired menu item.
More than 50㏈ (AGC Off)
Horizontal Resolution
- Left and Right Button : Used to move the cursor left or right in the menu screen or to
Horizontal : 700 TV-Line (Color)[Min] / 800 TV-Line (B/W)[Min]
Lens
change the value of the selected item.
② Power Led
C / CS MOUNT
Video Output Level
1.0 Vp-p (75Ω, Composite)
Min. Illumination
- When power is properly connected, this LED comes on.
③ Video Output Port
Color : 0.05Lux(50IRE@F1.2)
Sync System
Internal
O.S.D
- Video signals are output through this port. Connect this port to the Video IN port of a monitor
④ Day & Night Input Port
Built-in & Available
Auto / Flk
Electronic Shutter Speed
(NTSC : 1/60sec ~ 1/100,000sec)
DWDR
- You can switch to Day & Night mode by connecting an external signal to this port.
(PAL : 1/50sec ~ 1/100,000sec)
ON / Off (Level Adjustable)
AGC
- You can control SETUP Menu through this port by using external controllers like a remote
Low / Middle / High / Off
White Balance
controller that RS-485 Communication is supported.
ATW1/ATW2/AWC-SET/ATNI.CRL/ MANUAL(MANUAL/INDOOR/OUTDOOR)
Backlight Compensation
BLC / HLC / Off
Day & Night
RS-485 Interface
START
Camera Title
The camera can be controlled by using external controllers like a reomote controller.
On / Off (Selectable)
Motion Detection
On / Off (4 Zone Selectable)
Privacy Masking
On / Off (8 Zone Selectable)
Parking Line
ON / Off (Level Adjustable)
1. To control by PC
- Connect the RS-485 control port of the camera and the serial cable through an RS-485 converter
EX) PC Serial Port (COM1)→Serial Cable→RS-485 Converter→Camera RS-485 Converter Port
2. To Control by DVR or System Controller
Lens Shading / 2DNR / Mirror / Font color / Contrast / Sharpness
Image Adjust
- Connect the RS-485 cable(TRX+, TRX-) to the port of RS-485 cotrol board that is
Display(CRT,LCD,USER) / NEG.IMAGE
Language
English/Chinese/Spanish/Russian/Deutsch/Portuguese/French/Japanese
Supplied Voltage
Dimension
⑥ Power Input Port
- Connect the power as specified for each model.
Auto / B.W / Color / EXT
DPC
⑤ RS-485 Control Port
connected with DVR or System controller
AC230V ±10%
485 Control Board Connection Port
RS-485 Control Port
66.5(W)*54.2(H)*93.6(D)mm
(+) CONNCTION TERMINAL (TRX+)
485 +
Approx. 195g
(-) CONNCTION TERMINAL (TRX-)
485 -
Weight
*RS-485 Communication establishment initial value
Item
Camera ID
BAUD RATE
UART MODE
PET PKT
Initial value
1
9600
8 - NONE - 1
Enable
3
EXPOSURE
4
▶ SHUTTER : You can select either auto or manual shutter.
- FLK : Select this when you see picture flilker, this can happen when the frequency
Notes
⊙ To control the camera by constructing an additional controller, use Pelco-D portocol.
of the local lighting clashes with carmera
- Auto : Automatically changes by brightness of enviromente
■ Function menu Structure
▶ AGC: You can adjust it Low, Middle and High level.
The higher the gain level, the brighter the screen but the higher the noise.
Function Menu
LENS
■ DC
■ VIDEO
■ MANUAL
EXPOSURE
■ SHUTTER
■ AGC
■ DWDR
WHITE BAL.
■ ATW1
■ ATW2
■ AWC→SET
▶ DWDR : If there are bright area and dark area on the screen at the same time,
this function makes both areas to be in clear image
- ON/OFF
■ ANTI.CRL
■ MANUAL (MANUAL, INDOOR, OUTDOOR)
BACKLIGHT
■ OFF
■ BLC
■ HLC
DAY&NIGHT
■ COLOR
■ B/W
■ EXT
DPS
■ START
■ CAM TITLE
■ MOTION
■ PRIVACY
■ COMM ADJ.
■ LANGUAGE
■ VERSION
■ IMAGE ADJ.
● LENS SHAD.
● 2DNR
● MIRROR
● FONT COLOR
● CONTRAST
● SHARPNESS
● DISPLAY(CRT,LCD,USER)
● NEG. IMAGE
SPECIAL
■ AUTO
■ PARK. LINE
DWDR OFF
WHITE BAL.
※ Select one of the following 4 modes, as appropriate for your purpose
▶ ATW1 : Select this when the color temperature is between 2,000ºK and 18,000ºK.
■ SAVE / NOT SAVE / RESET
EXIT
DWDR ON
▶ ATW2 : Select this when the color temperature is between 2,500ºK and 98,000ºK.
How to set the Camera
▶ AWC-> SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
Notes
the SET button. If the environment changes, readjust it.
⊙ All item with the
, you can move to sub menu pressing SET button.
⊙ An item with the - - -, icon is unavailable due to function settings
▶ MANUAL
- MANUAL : Select this to fine-tune White Balance manually. Set White Balance first
LENS
by using the ATW or AWC mode. After that switch to MANUAL mode.
● Using this function, you can control screen brightness
Adjust the [BLUE] and [RED], according to the changing of color on the screen
1. When the SETUP menu screen is displayed, select 'LENS' by using the Up and
Down buttons so that the arrow indicates 'LENS'.
- INDOOR : Select this when the color temperature is around 3,100ºK.
- OUTDOOR : Select this when the color temperature is around 5,100ºK.
2. Select the connected type by using Left and Right buttons
Notes
▶ DC/VIDEO : Select Auto Iris Lens
- When DC is selected, you can control screen brightness.The range of brightness control is between 0and100.
Adjust the brightness appropriately for optimal screen brightness.
⊙ White balance may not work properly under the following conditions.
In this case, select the AWC mode.
① When color temperature of environment surrounding the subject is out of the control range
② If the camera towards a fluorescent, the White Balance operation may become unstable
- MANUAL : Select Manual Lens
BACKLIGT
▶ IRIS SPEDD : 0 ~ 15(5 DEFUALT)
⊙ Some lenses may not work properly, depending on the setting of the Brightness Level.
⊙ When using a video-type Auto Iris Lens
① Adjust the ALC adjustment terminal on the lens appropriately. In general, set it to AV.
② It may not work properly depending on the installed lens. Set the Level VR of the lens
to the optimal value.
③ Set the AGC to OFF and adjust the lens VR to an appropriate brightness.
④ Adjust the Lens VR, adjust the BRIGHTNESS, and then check if the screen brightness
changes properly. Otherwise, adjust the Lens VR again.
Notes
▶ BLC : This function allows you to get a clear pictures of objects even the objects
in strong backlight.
- Enables a user to directly select a desired area from a picture, and to view the area more clearly.
▶ HLC : If there is a high light installed in a limited environment such as an apartment
parking garage or gas station entrance, removing the hight light makes
it possible to view car license plates efficiently.
- Close the lens to shield the light, Select the START and press the SET button twice.
5
6
then you can see "PROCESSING NOW" displyed on the screen.
SPECIAL
▶ CAM TITLE : If you enter a title, the title will be appear on the monitor.
① If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the
arrow indicates 'CAM TITLE'
OFF
② Set it to 'On' by using Left and Right buttons.
ON
* AREA SELECT : You can select up to 8 privacy areas.
- LEVEL : Less value Masking Area gets bigger
* AREA DISPLAY : Determines whether to use the area selected in the AREA SELECT.
- MODE
* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
* NIGHT ONLY : It's only working at the low light conditions.
* WIDTH : adjust the selected vertical area.
* ALL DAY : It's working in daytime or nighttime.
* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.
DAY&NIGHT
* HEIGHT : adjust the selected horizontal area.
● You can display pictures in Color or Black and White.
* COLOR : Determine area color. You can select 0 ~ 15.
▶ COLOR : The picture is always displayed in color.
▶ PARK. LINE : It shows the parking line on the video
▶ AUTO : The mode is switched to ‘Color’ in a normal environment,
① When the SPECIAL menu screen is displayed, press the Up and down buttons so that
but switches to ‘B/W’ mode when ambient illumination is low.
the arrow indicates "PARK, LINE.".
To set up the day/night switching delay time for AUTO mode, press the SET button.
② Press SET button for Sub Menu.
also you can select the duration time about changing
③ Set up the mode using the 4 direction buttons.
the D(Day) → N(Night) and N(Night) → D(Day) mode.
* LT : Left Top(Move Left or Right)
- D→N LEVEL : The condition about changing color to B/W mode.
* LB : Left Back(Move Left or Right)
( Increase the level, switches to B/W slowly )
* RT : Right Top(Move Left or Right)
- D→N DELAY : The time about changing color to B/W mode.
* RB : Right Back(Move Left or Right)
- N→D LEVEL : The condition about changing B/W to COLOR mode.
* F : Change Distance of Top Line(Move Up or Down)
( Increase the level, switches to Color fast )
* N : Change Distance of Back Line(Move Up or Down)
- N→D DELAY : The time about changing B/W to COLOR
* T : Thickness of the Line
▶ B/W : The picture is always displayed in black and white.
▶ IMAGE ADJ.
- BURST : The picture is always displayed in black and white.
① When the SPECIAL menu screen is displayed, press the Up and down buttons so that
- IR SMART : When IR LED is turned on in B/W, the objects can be clearly identified due to the
function that decreases screen saturation of objects within a short distance.
the arrow indicates "IMAGE ADJ.".
② Press SET button for Sub Menu.
* IR GAIN : Change the IR gain level(Saturation)
- LENS SHAD. : Protect Shading area when use Wide Angle View Lens
* HEIGHT : adjust the selected horizontal area.
* LEVEL : Bigger No. more Bright
* WIDTH : adjust the selected vertical area.
- 2DNR : This function reduces the background noise in a low luminance environment
* LEFT/RIGHT : Determines the coordinate of the vertical axis for Area.
- MIRROR : you can flip the image vertically on the screen.
* TOP/BOTTOM : Determines the coordinate of the horizontal axis for area.
- FONT COLOR : OSD Font & Color Change
- IR LEVEL : ※ OPTION
* FONT : 15 steps OSD Font & Color
* HIGH : IR LED Fully ON
* ID&TITLE : 15 steps of CAM TITLE Color
* LOW : IR LED Half(1/2) ON
- CONTRAST : Bigger No. more dark
▶ EXT : Deactivates the EXT function.
- SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer.
DPC(Dead Pixel Compensation)
Adjust this value appropriately depending on the sharpness of the picture.
● Defect CCD correction to compensate for defects that can occur at the
- DISPLAY : CRT,LCD,USER(Selectable)
low light conditions.
* CRT : Please select this menu item when using a CRT monitor.
- PED LEVEL : Bigger No. more brighter
7
- COLOR GAIN : Bigger No. more dark
▶ PRIVACY : Hide an area you want to hide on the screen.
8
① When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the
* LCD : Please select this menu item when using an LCD monitor.
arrow indecates 'PRIVACY'.
- Standard value is 0.55. You can adjust the value between 0.05 ~ 1.00
② Press SET button for Sub Menu.
- PED LEVEL : Bigger No. more bright in dark
③ Set up the mode by using 4 direction buttons.
- COLOR GAIN : Bigger No. more dark and strong color
- GAMMA : Standard value is 0.45. You can adjust the value between 0.05 ~ 1.00
- PED LEVEL : Bigger No. more bright in dark
Notes
⊙ When the CAM TITLE menu is 'OFF', no title will be displayed on the monitor screen even if you
enter one.
- COLOR GAIN : Bigger No. more dark and strong color
- NEG.IMAGE : you can flip the color on screen.
③ Press the SET button.
▶ COMM ADJ.(RS485) : ※ OPTION
④ Use the 4 direction buttons to move to a desired letter and select the letter by pressing the
- This function sets up the camera communication status when controlling
the camera through an external device.
SET button. Repeat this to enter multiple letters. You can enter up 15 letters.
① When the SPECIAL menu screen is displayed, press the Up and down buttons so that
Notes
⊙ If you entered wrong letter……
If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a leeter,
change the cursor to the bottom left arrow and press the SET button. Move the curson over the
letter to be edited, move the cursor to the letter to be inserted and then press SET button.
the arrow indicates "COMM ADJ.".
② Press SET button for Sub Menu.
- CAM ID : Determines the camera's ID number (0~255)
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600bps.
⑤ Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears
- PROTOCOL : PELCO-D, PELCO-P, NEXTCHIP PROTOCOL
- DISPLAY ID : Display camera title on the screen.
on the screen. Select the position to display the title on the screen by using the 4 directoin
- ID POS : CAM ID Position
buttons and press the SET button. When the position is determined, select 'END' and press
the SET button to return to the SPECIAL menu.
▶ LANGUAGE : You can select the menu language according to your requirement.
▶ MOTION : Whenever motion is detected. The "motion detection" displayed at the
- Supplied Language : English, Chinese, Spanish, Russian, Deutsch, Portuguese,
bottom of the screen.
① When the SPECIAL menu is displayed, press the Up and Down buttons so that arrow indicates
French, Japanese
▶ VERSION : Camera Version
EXIT
MOTION.
② Press SET button for sub menu.
▶ SAVE, NOT SAVE, RESET
③ Set up the mode using the 4 direction buttons.
▶ RESET : Resets the camera settings to the factory defaults.
* AREA SEL : Determines which 4 vertices of each MD area is to be used
* AREA STATE :Determines whether to use the MOTION area selected.
* HEIGHT : adjust the selected horizontal area.
* WIDTH : adjust the selected vertical area.
* LEFT/RIGHT : Determines the coordinate of the vertical axis for Area.
* TOP/BOTTOM : Determines the coordinate of the horizontal axis for area.
* DEGREE : When sensitivity number is high, motion detection sensitivity
is increased to recognize even small movement
* VIEW : If you make it ON by using LEFT and RIGHT buttons, selected
alue of color is filled on the screen
Notes
⊙ MD areas show only MOTION menu. Therefore, MD areas don't display on the monitor screen.
⊙ BUT if you select the motion view function ON, MD areas are displayed on the monitor
* Note : It do not effect to Lenguage, Camera Tile and Communication Setting
MEMO
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising