MPS1000 v31.book
MPS1000
4-Port, 8-Port, or 16-Port Multi-Protocol Communications Server
Hardware Manual
205 Indigo Creek Drive
Rochester, NY 14626
Phone 585.256.0200
w w w. p t . c o m
support@pt.com
Document Revision History
Part Number
Date
Explanation of Changes
106p1670.10
October 22, 2003
Initial Release
106p1670.20
March 27, 2006
Reformatted Manual
106p1670.21
July 30, 2008
Added temperature, humidity and altitude requirements to
Operating and Storage Conditions. Reformatted Manual
106p1670.30
August 24, 2009
Added 4-port MPS1000 to manual. New product photographs.
Updated Table 2-1 part numbers, removed non-ROHS part
numbers. Added Upgrading a 4-Port Version to an 8-Port
Version topic. Renamed and reorganized manual.
106p1670.31
September 28, 2011
The following changes have been made to this document on
this date:
- Updated reliability information for chassis (MTBF). See
Reliability on Page 29
- Updated illustrations, because chassis is no longer equipped
with power indicator LED (Green). See Figure 3-3, “Rear View
16-Port MPS1000,” on page 26 and Figure 3-4, “Rear View 4Port MPS1000,” on page 27
- Updated document with re-branded template
Copyright Notice
© Copyright 2004-2011 by Performance Technologies, Inc. All Rights Reserved.
Trademarks
PT is a trademark of Performance Technologies, Inc.
IPnexus®, Nexusware®, SEGway®, Simply Smarter Signaling®), and the PT logo are
trademarks and registered trademarks of PT.
CompactPCI® and PICMG® are registered trademarks of the PCI Industrial Computer
Manufacturers Group.
All product and brand names may be trademarks or registered trademarks of their respective
owners.
Errors and Omissions
Although diligent efforts are made to supply accurate technical information to the user,
occasionally errors and omissions occur in manuals of this type. For the most current user
documentation, contact Signaling Systems Customer Support.
PT reserves its right to change product specifications without notice.
Disclaimer
This document is the sole property of PT. This document presents information for users of PT
products. Although the information contained within this document is considered accurate and
characteristic of the subject product, PT reserves the right to make changes to this document
and any products described herein to improve reliability, functionality, or design.
2
PT does not assume any liability arising out of the application or use of any product or circuit
described herein. No part of this document may be copied or reproduced in any form or by any
means without the prior permission of PT.
Symbols and Conventions in this Manual
The following symbols may appear in this document:
Caution:
There is risk of equipment damage. Follow the instructions.
Warning:
Hazardous voltages are present. To reduce the risk of electrical shock and danger to
personal health, follow the instructions.
Caution:
Electronic components on printed circuit boards are extremely sensitive to static electricity.
Ordinary amounts of static electricity generated by your clothing or work environment can
damage the electronic equipment. It is recommended that anti-static ground straps and
anti-static mats are used when installing the board in a system to help prevent damage due
to electrostatic discharge.
3
4
Contents
Chapter 1: About This Guide
13
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Customer Support and Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Customer Support Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Other Web Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Return Merchandise Authorization (RMA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 2: Introduction
17
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Extensive Software Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Feature Rich Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Multi-Networking Protocol Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Four-Port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Eight-Port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Sixteen-Port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
System Features and Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Models and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Chapter 3: Technical Information
23
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Front and Rear Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5
Contents
Operating and Storage Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Certification Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Safety Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
FCC (USA) Class A Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Industry Canada Class A Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Product Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Electrostatic Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Compliance with RoHS and WEEE Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapter 4: Chassis Installation
33
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Power and Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Input Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Additional Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electromagnetic Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6
Contents
Clean Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Powering Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Powering Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Chapter 5: On-Site Replacements and Upgrading
37
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Powering Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Replacing a Card in an 4-port, 8-port or 16-Port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Removing a CPC358 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Installing a CPC358 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Upgrading a 4-Port Version to an 8-Port Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Upgrading an 8-Port Version to a 16-Port Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Battery Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Chapter 6: Configuration Settings
43
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Jumper and Switch Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
4-Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
8-Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
16-Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Index
47
7
Contents
8
Tables
Table 2-1: PTI Part Numbers for MPS1000 Versions and Accessories . . . . . . . . . . . . . . . . . . . . . . . 21
Table 3-1: Ambient Temperature Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3-2: Humidity Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3-3: MTBF for MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 4-1: Power Requirements (Input/Primary) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 4-2: Chassis Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 6-1: K5 and K38 Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 6-2: SW1 DIP Switch Settings for MPS1000 4-Port Version . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 6-3: SW1 DIP Switch Settings for MPS1000 8-Port Version . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 6-4: SW1 DIP Switch Settings for MPS1000 16-Port Version . . . . . . . . . . . . . . . . . . . . . . . . . 46
9
Tables
10
Figures
Figure 3-1: Front View 16-Port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 3-2: Front View 4-Port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 3-3: Rear View 16-Port MPS1000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 3-4: Rear View 4-Port MPS1000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 5-1: CPC358 Latches with Lock Release Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 5-2: Card Installation Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 6-1: K5, K38 Jumpers and SW1 Switch Location on the CPC358 . . . . . . . . . . . . . . . . . . . . . 44
11
Figures
12
Chapter 1
About This Guide
Introduction
This guide describes Performance Technologies, Inc. MPS1000 Multi-Protocol Servers. This
manual covers the 4-port, 8-port, and 16-port versions. A brief description of what you’ll find in
this guide is listed below:
Chapter 2, “Introduction,” on page 17 provides an MPS1000 product overview.
Chapter 3, “Technical Information,” on page 23 contains photographs of the MPS1000, product
specifications, and electrical and environmental considerations for the system.
Chapter 4, “Chassis Installation,” on page 33 contains information on power requirements, ESD
concerns and installing the MPS1000 chassis in 19 inch racks.
Chapter 5, “On-Site Replacements and Upgrading,” on page 37 contains information on
installing CPC358s and RTM358s into the MPS1000 chassis in the event replacement or
upgrading is needed.
Chapter 6, “Configuration Settings,” on page 43 provides jumper and switch locations and
setting information for configuring the 4-port, 8-port, or 16-port MPS1000.
An “Index,” on page 47 is also provided.
Text Conventions
This guide uses the following text conventions:
Convention
Used For
Monospace font
Monospace font represents sample code
Bold font
Bold font represents:
• paths
• file names
• UNIX commands
• user input
Italic font
Italic font represents:
• notes that supply useful advice
• supplemental information
• referenced documents
13
Chapter 1: About This Guide
Customer Support and Services
PT offers a variety of standard and custom support packages to ensure customers have access
to the critical resources that they need to protect and maximize hardware and software
investments throughout the development, integration, and deployment phases of the product
life cycle.
If you encounter difficulty in using this PT product, you may contact our support personnel by:
1. E-MAIL (Preferred Method) – e-mail us at the addresses listed below or use our online e-mail support
form. Outline your problem in detail. Please include your return e-mail address and a telephone
number.
2. TELEPHONE – Contact us using telephone at the number listed below, and request Technical
Support. Our offices are open Monday to Friday, 8:00 a.m. to 8:00 p.m. (Eastern Time).
PT Support Contact Information
Embedded Systems and Software
(Includes Platforms, Blades, and Servers)
SS7 Systems
(Includes SEGway™)
Email
support@pt.com
ss7support@pt.com
Phone
+1 (585) 256-0248
(Monday to Friday, 8 a.m. to 8 p.m.
Eastern Time)
+1 (585) 256-0248
(Monday to Friday, 8 a.m. to 8 p.m.
Eastern Time)
If you are located outside North America, we encourage you to contact the local PT distributor
or agent for support. Many of our distributors or agents maintain technical support staffs.
Customer Support Packages
Our configurable development and integration support packages help customers maximize
engineering results and achieve time-to-market goals. To find out more about our Customer
Support packages, visit http://www.pt.com/page/support/.
Other Web Support
Support for existing products including manuals, release notes, and drivers can be found on
specific product pages at http://www.pt.com. Use the product search to locate the information
you need.
Return Merchandise Authorization (RMA)
To submit a return merchandise authorization (RMA) request, complete the online RMA form
available at http://pt.com/assets/lib/files/rma-request-form.doc and follow the instructions on
the form. You will be notified with an RMA number once your return request is approved.
Shipping information for returning the unit to PT will be provided once the RMA is issued.
14
Product Warranty
Product Warranty
Performance Technologies, Incorporated, warrants that its products sold hereunder will at the
time of shipment be free from defects in material and workmanship and will conform to
Performance Technologies’ applicable specifications or, if appropriate, to Buyer’s specifications
accepted by Performance Technologies in writing. If products sold hereunder are not as
warranted, Performance Technologies shall, at its option, refund the purchase price, repair, or
replace the product provided proof of purchase and written notice of nonconformance are
received by Performance Technologies within 12 months of shipment, or in the case of
software and integrated circuits within ninety (90) days of shipment and provided said
nonconforming products are returned F.O.B. to Performance Technologies’s facility no later
than thirty days after the warranty period expires. Products returned under warranty claims
must be accompanied by an approved Return Material Authorization number issued by
Performance Technologies and a statement of the reason for the return. Please contact
Performance Technologies, or its agent, with the product serial number to obtain an RMA
number. If Performance Technologies determines that the products are not defective, Buyer
shall pay Performance Technologies all costs of handling and transportation. This warranty
shall not apply to any products Performance Technologies determines to have been subject to
testing for other than specified electrical characteristics or to operating and/or environmental
conditions in excess of the maximum values established in applicable specifications, or have
been subject to mishandling, misuse, static discharge, neglect, improper testing, repair,
alteration, parts removal, damage, assembly or processing that alters the physical or electrical
properties. This warranty excludes all cost of shipping, customs clearance and related charges
outside the United States. Products containing batteries are warranted as above excluding
batteries.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS,
IMPLIED OR STATUTORY INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS. IN NO EVENT SHALL PERFORMANCE TECHNOLOGIES BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES DUE TO BREACH OF THIS WARRANTY
OR ANY OTHER OBLIGATION UNDER THIS ORDER OR CONTRACT.
15
Chapter 1: About This Guide
16
Chapter 2
Introduction
Overview
This chapter provides an introduction to the MPS1000. Topics covered in this chapter include:
•
“Product Description,” on page 17
•
“Product Features,” on page 19
•
“System Features and Capabilities,” on page 20
•
“Models and Accessories,” on page 20
Product Description
The MPS1000 is a WAN-LAN Data Communication Server that attaches to your local-area
network to provide wide-area connectivity. A single MPS communication server can support a
number of WAN protocols, each of which can be accessed simultaneously by multiple clients.
The MPS1000 is a robust WAN-over-IP communications server that is ideal for bringing WAN
gateway connectivity to your local area network. It provides two 10/100 Mb Ethernet ports and
four, eight, or 16 high-speed WAN serial ports, making it ideal as an intelligent WAN/LAN
bridge, WAN/LAN gateway device, or a remote WAN connectivity server. Using SNMP
management, any computer and/or workstation equipped with TCP/IP on the LAN can access
information from the MPS communications server.
The MPS1000 is designed to preserve the user's software investment; all of Performance
Technologies’ WAN Communications products enable applications developed on one to be
moved to any of the other WAN products. Its modular design supports virtually any
synchronous serial communications protocol.
Extensive Software Support
The MPS1000 is enabled with the Linux-based NexusWare® Core development environment.
With the wide acceptance and extensive number of publicly available applications and
protocols, available for Linux, system developers can bring sophisticated systems to market in
a much shorter time.
Equipped with a well-defined API, the integrated protocol suite from Performance Technologies
reduces time to market by eliminating unnecessary development efforts at the hardware/
protocol level. The depth and flexibility of the protocols offered by Performance Technologies
for our WAN hardware products enable development engineers to proceed directly to
integration and application development.
Performance Technologies' suite of WAN communications protocols provides complete WAN
connectivity solutions for Frame Relay, HDLC, LAPD, X.25 and Radar Receiver/SBSI
protocols. Operating system support for the MPS1000 includes Solaris™/UNIX®, Windows
XP®, and Linux®.
17
Chapter 2: Introduction
Feature Rich Hardware
The MPS1000 is designed as a fully programmable communications system capable of
sustaining high data rates for a variety of protocols used in synchronous communications.
The MPS1000 utilizes single or dual Motorola MPC8255 PowerQUICC™ II communications
microprocessors. In a dual configuration, one of the processors is configured as the Master and
the other is configured as the Slave. The default mode of operation uses the Slave processor
with its CPU core disabled, leaving the CPM active for serial communication.
Two external Ethernet PHYs are offered to provide Ethernet redundancy. The MPS1000 will
automatically switch over to the secondary Ethernet PHY if link is lost on the primary PHY.
The MPS1000 supports eight or sixteen identical, individually programmable, synchronous
serial I/O ports. The ports are capable of electrically interfacing to V.35, RS442 (EIA530 or
RS449) and RS232 equipment. Each port is brought out in groups of four to an 80-pin
connector that supports Performance Technologies quad connection hydra line of serial I/O
cables.
A four-port version of the MPS1000 is capable of interfacing to EIA530 and RS232 equipment.
Each port is brought out to a DB25 male connector on the rear of the unit. No hydra cables are
required.
With rack-mountable or freestanding configurations, the MPS1000 provides the power to
handle full load network traffic, and communicates via TCP/IP with clients on the LAN.
18
Product Features
Multi-Networking Protocol Capabilities
With the multi-protocol architecture of the MPS, standard and custom protocols supplied by
Performance Technologies can coexist on the same server with protocols you develop yourself.
A single MPS server provides the unique combination of WAN and LAN protocols you need,
giving you an integrated networking solution.
Product Features
The MPS1000 comes in three versions: four port, eight port, or sixteen port. The four-port
version can be upgraded by the user to become an eight-port version. The eight-port version
can be upgraded by the user to become a 16-port version. Photographs of the 4-port MPS1000
and the 16-port MPS1000 can be seen in “Front and Rear Features,” on page 24. The
highlights for each version are listed below.
Four-Port MPS1000
A four-port MPS1000 has the following attributes:
•
4 high-speed WAN ports - up to 2.0 Mpbs bi-directional, simultaneously
•
Two 10/100 Base-T Ethernet ports
•
One 233 MHz Motorola MPC8255 PowerQUICC II processor
•
128 MB shared DRAM
•
32 Mbyte application flash PROM
•
512 KBytes boot PROM
•
SNMP (Basic MIB II) support allowing MIB Browser or SNMP management of the server
Note: See “Upgrading a 4-Port Version to an 8-Port Version,” on page 40 for information on
upgrading.
Eight-Port MPS1000
An eight-port MPS1000 has the following attributes:
•
8 high-speed WAN ports - up to 2.0 Mpbs bi-directional, simultaneously
•
Two 10/100 Base-T Ethernet ports
•
One 233 MHz Motorola MPC8255 PowerQUICC II processor
•
128 MB shared DRAM
•
32 Mbyte application flash PROM
•
512 KBytes boot PROM
•
SNMP (Basic MIB II) support allowing MIB Browser or SNMP management of the server
Note: See “Upgrading an 8-Port Version to a 16-Port Version,” on page 41 for information on
upgrading.
19
Chapter 2: Introduction
Sixteen-Port MPS1000
A 16-port MPS1000 has the following attributes:
•
16 high-speed WAN ports - up to 2.0 Mpbs bi-directional, simultaneously
•
Two 10/100 Base-T Ethernet ports
•
Two 233 MHz Motorola MPC8255 PowerQUICC II processors
•
Two x 128 MB shared DRAM
•
Two x 32 Mbyte application flash PROM
•
Two x 512 KBytes boot PROM
•
SNMP (Basic MIB II) support allowing MIB Browser or SNMP management of the server
System Features and Capabilities
Each MPS1000 is a 1U-high WAN-LAN data communications server that attaches to your
local-area network to provide wide-area connectivity. The MPS1000 contains one or two
CPC358s, octal synchronous serial communication processors, which can be preloaded with
one or more protocols.
For more information about the CPC358 or RTM258, refer to the CPC358 Octal Synchronous
Serial Communications Processor Hardware Manual.
Models and Accessories
Table 2-1, “PTI Part Numbers for MPS1000 Versions and Accessories,” on page 21 lists the
PTI RoHS part numbers for the MPS1000 versions and accessories required to operate the
server.
This manual covers both RoHS and Non-RoHS versions of the MPS1000. See “Compliance
with RoHS and WEEE Directives,” on page 31 for information about RoHS compliance.
Note: Refer to the Performance Technologies Web site to find the non-RoHS part Numbers for
some of these products if needed:
http://pt.com/page/about-us/ehsms/rohs-compliant/
20
Models and Accessories
Table 2-1:PTI Part Numbers for MPS1000 Versions and Accessories
Item
PTI Part Number
MPS1000 Versions
MPS1000 - 4-Port Multi-Protocol Communications Server
PT-MPS1000-12386
MPS1000 - 8-Port Multi-Protocol Communications Server
PT-MPS1000-12159
MPS1000 - 16-Port Multi-Protocol Communications Server
PT-MPS1000-12035
Serial Communications Processors
CPC358 - 8-Port Synchronous Serial Controller, Rear I/O
PT-CPC358-11932
CPC358 - 8-Port Synchronous Serial Controller, Front I/O
PT-CPC358-11933
Rear Transition Modules
RTM358 - 4-Port, 2 Slot, Rear I/O, DTE RS232/EIA530
PT-RTM358-12382
RTM358 - 8-Port, Rear I/O, DTE RS232/RS449/422/EIA530/V.35, DCE V.35
PT-RTM358-11934
RTM358 - Front I/O, Ethernet only
PT-RTM358-11970
Cables1
4 x RS232 Hydra Cable, DTE with Jackscrews
PT-ACC334-11919
4 x RS232 Hydra Cable, DTE with Thumbscrews
PT-ACC334-12274
4 x EIA530 Hydra Cable, DTE with Jackscrews
PT-ACC334-11969
4 x EIA530 Hydra Cable, DTE with Thumbscrews
PT-ACC334-12273
4 x RS449 Hydra Cable (Socket) Sun Substitute, DTE with Jackscrews (Female)
PT-ACC334-11920
4 x RS449 Hydra Cable (Pin), DTE with Jackscrews (Male)
PT-ACC334-11921
4 x V.35 Hydra Cable, DTE with Thumbscrews
PT-ACC334-11918
4 x V.35 Hydra Cable, DCE with Thumbscrews
PT-ACC358-11971
RS232 Debug Cable (console)
PT-ACC358-12275
Rear Filler Panels
6U 1-Slot Rear Filler Panel
PT-ACC5040-12059
1. Please note that the hydra cables are not required for the 4-port version of the MPS1000 (PT-MPS1000-12386).
21
Chapter 2: Introduction
22
Chapter 3
Technical Information
Overview
This chapter contains front and rear photographs of the MPS1000, product specifications, and
electrical and environmental considerations for the system. Topics covered in this chapter
include:
•
“Front and Rear Features,” on page 24
•
“Front View,” on page 24
•
“Rear View,” on page 26
•
“Operating and Storage Conditions,” on page 28
•
“Specifications,” on page 29
•
“Certifications,” on page 29
•
“Regulatory Information,” on page 30
•
“Product Safety Information,” on page 30
•
“Compliance with RoHS and WEEE Directives,” on page 31
23
Chapter 3: Technical Information
Front and Rear Features
Front View
16-Port MPS1000
Figure 3-1, “Front View 16-Port MPS1000,” shows an example of the front of a 16-port
MPS1000. The 16-port MPS1000 contains two CPC358 cards in the front and two RTM358
cards in the rear of the chassis.
Figure 3-1: Front View 16-Port MPS1000
Board Status,
Ethernet, and
Port Status LEDs
Mounting Bracket
CPC358 (Rear I/O)
Node Glyph
CPC358 (Rear I/O)
Hot-Swap LED
Mounting Bracket
Air Intake
ESD Jack
Console Port
Eight-Port MPS1000
The 8-port MPS1000 looks similar to the 16-port version, but it does not have a second
CPC358 card in the front or a second RTM358 in the rear of the chassis. The empty slots in the
front and rear of the 8-port MPS1000 contain filler panels.
Note: Both slots are non-H.110 slots.
24
Front and Rear Features
Four-Port MPS1000
Figure 3-2, “Front View 4-Port MPS1000,” shows an example of the front of a 4-port MPS1000.
The 4-port MPS1000 contains one CPC358 card in the front and a single 4-port RTM358 in the
rear of the chassis. The empty slot in the front of the 4-port MPS1000 contains a filler panel.
Figure 3-2: Front View 4-Port MPS1000
Board Status,
Ethernet, and
Port Status LEDs
Mounting Bracket
Filler Panel
Node Glyph
CPC358 (Rear I/O)
Hot-Swap LED
Console Port
25
Mounting Bracket
Air Intake
ESD Jack
Chapter 3: Technical Information
Rear View
16-Port MPS1000
Figure 3-3, “Rear View 16-Port MPS1000,” shows an example of the back of a 16-port
MPS1000. The 16-port MPS1000 contains two RTM358 cards in the rear of the chassis.
Cabling
* ENET B (Ports “B”) should be connected using the supplied Crossover Cable. ENET A (Ports
“A”) should not be connected with a Crossover Cable. This only applies to the 16-port version.
No cable is needed for the 8-port or 4-port version of the MPS1000.
Figure 3-3: Rear View 16-Port MPS1000
Power Supply
Fan (Exhaust)
Power Cord
Connector
Ethernet
LEDs
RJ45 Ethernet
Ports A & B
ESD Jack
RTM358
(Rear I/O)
80-Pin Connectors
Grounding
Lug
Power Switch
Ethernet RJ45 Ethernet
LEDs
Ports A & B
80-Pin Connectors
RTM358
(Rear I/O)
Eight-Port MPS1000
The MPS1000 8-port version looks similar to the 16-port version but does not have a second
RTM358 in the rear of the chassis. The empty slot in the back of the 8-port version contains a
rear filler panel.
26
Front and Rear Features
Four-Port MPS1000
Figure 3-4, “Rear View 4-Port MPS1000,” shows an example of the back of a 4-port MPS1000.
The 4-port MPS1000 contains a single 4-port RTM358 in the rear of the chassis. The 4-port
RTM front panel takes up two CPCI slots (double wide).
Figure 3-4: Rear View 4-Port MPS1000
4-Port RTM358 (Rear I/O) with
Double-wide CPCI 6UX8HP
Front Panel
Power Supply
Fan (Exhaust)
Power Cord
Connector
Power Switch
ESD Jack
RJ45 Ethernet
Ports A & B
DB25 Connectors
Grounding
Lug
Ethernet
LEDs
DB25 Connectors
27
Chapter 3: Technical Information
Operating and Storage Conditions
The operating conditions for the MPS1000 are based upon the requirements defined in the
following tables.
Warning:
Do not restrict air flow through the vents.
Temperature
The MPS1000 should be installed in a location that allows airflow through the front, rear, and
side of the unit. Temperature requirements are shown in Table 3-1, “Ambient Temperature
Requirements,”.
Table 3-1:Ambient Temperature Requirements
Operation
Minimum
Maximum
Operating
0°C (32° F)
50°C (122° F)
Storage
-40°C (-40° F)
70°C (158° F)
Humidity
Humidity requirements are shown in Table 3-2, “Humidity Requirements,”.
Table 3-2:Humidity Requirements
Operation
Minimum
Maximum
Operating
10%
85%
Storage
10%
85%
Altitude
The MPS1000 is designed to meet the requirement outlined in the NEBS GR-63 specification
with regard to Altitude.
28
Specifications
Specifications
The MPS1000 has the following electrical and mechanical specifications.
Power Requirements
The MPS1000 utilizes 2.0A @ 115V or 0.9A @ 230V.
Physical Dimensions
See “Dimensions,” on page 34 for more information.
Enclosure
19-inch rackmount or tabletop
Reliability
The following reliability tests have been performed for the MPS1000:
Table 3-3:MTBF for MPS1000
MPS1000 Version
MTBF in Hours
Using
4 port
217,784
Bellcore SR-332 Issue 2
8 port
272,453
Bellcore SR-332 Issue 2
16 port
272,253
Bellcore SR-332 Issue 2
Certifications
The MPS1000 meets the following safety and certification standards.
Certification Standards
The MPS1000 meets the following standards:
•
FCC Class A
•
CE
•
ETSI EN 300 386
Safety Certifications
•
UL60950-1
•
EN60950-1:2006
29
Chapter 3: Technical Information
Regulatory Information
FCC (USA) Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
Note: Modifications made to this device that are not approved by Performance Technologies,
Inc. may void the authority granted to the user by the FCC to operate this equipment.
Industry Canada Class A Notice
This Class A digital apparatus complies with Industry Canada’s Equipment Standard for Digital
Equipment (ICES-003).
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Product Safety Information
Safety Precautions
This section is provided as a summary of the safety recommendations throughout this manual.
Performance Technologies recommends that all safety precautions be followed to prevent
harm to yourself or to the equipment. Please follow all warnings marked on the equipment.
Caution:
Ensure that the voltage and frequency of your power source matches the voltage and
frequency inscribed on the equipment's electrical rating label.
Caution:
Never push objects of any kind through the openings in the equipment. Dangerous voltages
may be present. Conductive foreign objects could produce a short circuit that could cause
fire, electrical shock, or damage the equipment.
30
Compliance with RoHS and WEEE Directives
Electrostatic Discharge
Caution:
Electronic components on printed circuit boards are extremely sensitive to static electricity.
Ordinary amounts of static electricity generated by your clothing or work environment can
damage electronic equipment. Use anti-static ground straps and anti-static mats when
handling components to prevent damage due to electrostatic discharge.
Compliance with RoHS and WEEE Directives
In February 2003, the European Union issued Directive 2002/95/EC regarding the Restriction
of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS) and
Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).
This product is compliant with Directive 2002/95/EC. It may also fall under the Directive 2002/
96/EC.
PT's complete position statements on the RoHS and WEEE Directives can be viewed on the
Web at: http://pt.com/page/about-us/ehsms/.
31
Chapter 3: Technical Information
32
Chapter 4
Chassis Installation
Overview
This chapter contains information on power requirements, ESD concerns and installing the
MPS1000 chassis in 19 inch racks. Topics covered in this chapter include:
•
“Power and Grounding,” on page 33
•
“Additional Requirements,” on page 34
•
“Mounting,” on page 35
•
“Powering Up,” on page 36
•
“Powering Down,” on page 36
Power and Grounding
The power requirements are shown in Table 4-1, “Power Requirements (Input/Primary),”:
Table 4-1:Power Requirements (Input/Primary)
Minimum
AC Voltage
AC Frequency
90 VAC
Nominal
180 VAC
115 VAC
47 Hz
230 VAC
60/50 Hz
Maximum
135 VAC
265 VAC
63 Hz
Ensure that your MPS1000 unit and the frame holding the unit are properly grounded.
Warning:
Use proper ESD protection to reduce the risk of damage to your equipment.
Input Supply
Check the system nameplate ratings to ensure that there is no overloading of the supply
circuits that could have an effect on overcurrent protection and supply wiring.
Grounding
The MPS1000 must maintain a constant grounding. It is important to inspect supply
connections to power strips and not just the direct connection to the branch circuit.
The protective grounding lug, located on the rear of the unit, is intended to be connected to the
supply circuit ground. Figure 3-3, “Rear View 16-Port MPS1000,” on page 26 and Figure 3-4,
“Rear View 4-Port MPS1000,” on page 27 show the location of the grounding lug.
33
Chapter 4: Chassis Installation
Additional Requirements
ESD
To reduce the risk of damage to equipment, the MPS1000 should be kept in an ESD protected
environment. The unit should be properly grounded at all times; it should be plugged in and its
grounding lug should be connected to the supply circuit ground. When performing routine
maintenance on the unit, a wrist strap should be used and plugged into one of the ESD jacks,
located on the front and rear of the chassis.
See Figure 3-1, Figure 3-2, Figure 3-3, and Figure 3-4 for the locations of the ESD jacks.
Warning:
Use proper ESD protection to reduce the risk of damage to your equipment.
Dimensions
The MPS1000 occupies an area of 17" W x 11.02" D x 1.75" H (432 x 280 x 44.5 mm), see
Table 4-2, “Chassis Dimensions,”. It is recommended that you allow for access to both front
and back panels of the unit when installing the MPS1000.
Table 4-2:Chassis Dimensions
Dimension
Millimeters
Inches
Height
44.5 mm
1.75 inches (1U)
Width
432 mm
17.0 inches
Depth
280 mm
11.02 inches
Weight
The MPS1000 weights 5.44 kg (12 lb.) unpackaged; and 8.35 kg (18.4 lb.) packaged.
Rack Mounting
If several rack-mounted units are installed in a rack, the ambient temperature within the rack
may be higher than the room temperature. Care should be taken to install the units such that
each has sufficient room for air inflow and exhaust, to allow proper cooling. Air flow in the
MPS1000 is from the front of the unit to the side and rear.
Rack-mounted units should be installed such that their weight is distributed properly in the rack.
Otherwise, the rack may be unstable and create a potential hazard.
If rack-mounted units are installed in a closed or multi-unit rack assembly, they may require
further evaluation by certification agencies.
34
Mounting
Electromagnetic Interference
The MPS1000 uses, generates, and can radiate electromagnetic energy. In order to avoid
electromagnetic interference issues affecting or caused by this unit, be sure to use adequate
EMI protection during its installation and operation.
Warning:
EMI Caution: The MPS1000 may cause or be susceptible to electromagnetic interference
(EMI) if it is not installed and used with adequate EMI protection.
Clean Environment
The MPS1000 should be operated in an environment with filtered air.
Note: The MPS1000 contains no internal user-serviceable parts; do not remove the cover.
CPC358 card insertion or removal must be done following PT’s instructions, using proper ESD
precautions. Attempting internal repairs during the warranty period may void the warranty.
Always refer servicing to qualified service personnel.
Mounting
Mounting points on the MPS1000 are located at the front on each side of the unit, allowing
mounting brackets to be used for front mounting. For other mounting options, please contact
Performance Technologies. The MPS1000 is designed to be installed in a standard 19 inch
mounting rack.
If several rack-mounted units are installed in a rack, the ambient temperature within the rack
may be higher than the room temperature. Care should be taken to install the units such that
each has sufficient room for air inflow and exhaust, to allow proper cooling.
35
Chapter 4: Chassis Installation
Powering Up
To power up the MPS1000, first ensure that power is supplied to the unit and that all cabling is
installed. Press the power switch (located on the back panel of the unit on the left-hand side).
Note: A pause of at least 3 seconds between shutdown of the MPS1000 and when it is
powered up again is preferred. This allows the capacitors in the sense feedback circuitry to
discharge fully.
Powering Down
To force a hard shutdown of the MPS1000, first make sure no applications are running, in order
to prevent loss of data. Press the power switch (located on the back panel of the unit on the
left-hand side).
The procedure for a soft shutdown of the MPS1000 is dependent upon the operating system it
is running. Your operating system will have a general procedure for shutdown, which should be
followed.
36
Chapter 5
On-Site Replacements and Upgrading
Overview
This chapter covers the removal and installation of replacement CPC358 cards in the event
that the MPS1000 needs to have cards replaced or repaired. It also covers upgrading a 4-port
version to an 8-port version and upgrading an 8-port version to a 16-port.
It is important to remember to follow safety procedures and grounding protocol in order not to
cause personal harm or equipment damage. If cards must be swapped out in the MPS1000, it
will be necessary to continue with the configuration of those cards as detailed in Chapter 6,
“Configuration Settings,” on page 43 before powering back up the MPS1000.
Topics covered in this chapter include:
•
“Replacing a Card in an 4-port, 8-port or 16-Port MPS1000,” on page 37
•
“Removing a CPC358,” on page 37
•
“Installing a CPC358,” on page 39
•
“Upgrading a 4-Port Version to an 8-Port Version,” on page 40
•
“Upgrading an 8-Port Version to a 16-Port Version,” on page 41
•
“Battery Instructions,” on page 42
Powering Down
To force a hard shutdown of the MPS1000, first make sure no applications are running, in order
to prevent loss of data. Press the power switch (located on the back panel of the unit on the
left-hand side).
The procedure for a soft shutdown of the MPS1000 is dependent upon the operating system it
is running. Your operating system will have a general procedure for shutdown, which should be
followed.
Replacing a Card in an 4-port, 8-port or 16-Port
MPS1000
The following instructions are used to replace a CPC358 card in a 4-port, 8-port, or 16-port
MPS1000.
Removing a CPC358
Follow these steps to remove a CPC358 from the MPS1000:
1. Unscrew the captive screws on the latches. Ensure that these screws are completely free before
trying to remove the card to prevent damage to the card and the MPS1000 chassis.
37
Chapter 5: On-Site Replacements and Upgrading
2. The latches have a locking mechanism, press it to unlock the latches.
3. Press the latches open. This will unseat the card from the pin connectors at the rear of the card slot.
4. Holding the card by its latches, pull the card gently straight out of the slot.
Card Latches
The CPC358 card uses the card latches shown in Figure 5-1, “CPC358 Latches with Lock
Release Buttons,”. Before removing a card, always ensure that the screws have been loosened
and are completely free from the chassis. When installing or removing a card, the latches must
always be in the open position.
Figure 5-1: CPC358 Latches with Lock Release Buttons
Lock Release Button
Screw location
(not visible)
To open this latch, first ensure that the screw is completely free from the
chassis, then push the lock release button. There will be an audible click as
the lock is released.
38
Replacing a Card in an 4-port, 8-port or 16-Port MPS1000
Installing a CPC358
Follow these steps to insert a CPC358 card into a MPS1000:
See Figure 5-2, “Card Installation Details,”.
1. Inspect the CPC358. If it is new, it may come with protective plastic covers on the latches’ captive
screws. These will need to be removed before the card can be installed.
2. Ensure that the card’s latches are open. The latches have a locking mechanism that will need to be
pressed in order to open the latches.
Note: It is important to remember if you are updating a 4-port version to an 8-port version,
updating an 8-port version to a 16-port version, adding a different card, or removing a card,
that the DIP switch SW1 is set properly for the running conditions of the MPS1000. Further
information on setting SW1 can be found on “DIP Switch Settings,” on page 45.
3. Holding the card by its latches, align the card in the MPS1000’s card guides.
4. Slide the card gently straight into the slot, keeping the card level. Do not apply too much pressure,
particularly if you feel resistance. You should feel the pin connectors on the rear of the card meet the
backplane.
5. Continue to slide the card into the slot until the latches touch the extrusions on either side of the slot.
6. Press down on the latches to guide the card the rest of the way into the slot and lock it into place. You
will hear a click as the latches are closed and the card is set into place.
7. After insertion, tighten the captive screws on the latches.
Figure 5-2: Card Installation Details
Extrusion
Captive
Screw
The notch in the latch
will butt up against the
extrusion when the card
is fully seated.
Once the card is fully seated,
press down on the latches to
guide the card the rest of the
way into the slot. You will
hear a click when installed
properly.
39
Chapter 5: On-Site Replacements and Upgrading
Upgrading a 4-Port Version to an 8-Port Version
In order to upgrade a 4-port version to an 8-port version, you must purchase the following from
Performance Technologies:
•
an 8-port RTM358
•
a 6U 1-Slot rear filler panel
•
the proper software
See Table 2-1, “PTI Part Numbers for MPS1000 Versions and Accessories,” on page 21 for
product part numbers.
Configuring and Installing the CPC358
After receiving the RTM358, use the following steps to configure and install the CPC358.
Follow these steps to configure the CPC358:
1. Remove the filler panel on the front of the MPS1000 by unscrewing the captive screws.
2. Remove the CPC358 following the steps described in “Removing a CPC358,” on page 37.
Note: It is important to remember if you are updating a 4-port MPS1000 to an 8-port
MPS1000, the SW1 switch on the CPC358 must be set properly for the running conditions
of the MPS1000. Further information on setting SW1 can be found on “DIP Switch Settings,”
on page 45.
3. Set the SW1-2 switch to the Open (OFF) position on the CPC358, as described in “8-Port
Configuration,” on page 45.
4. Reinsert the CPC358 following the steps described in “Installing a CPC358,” on page 39.
Installing the RTM358
Conversion to an 8-port MPS1000 requires the replacement of the 4-port RTM358 with an 8port RTM358. Additionally you will need to install a 6U 1-slot rear filler panel to maintain the
chassis’s shielding and cooling performance. The steps for installing the RTM and the rear filler
panel are as follows:
Follow these steps to insert an 8-RTM358 and rear filler panel into an MPS1000:
1. Inspect the 8-port RTM358 and the rear filler panel. If new, they may come with protective plastic
covers on the latches’ captive screws. These will need to be removed before the items can be
installed.
2. Remove the 4-port RTM at the rear of the MPS1000 chassis.
3. Ensure that the 8-port RTM358’s latches are open. The latches have a locking mechanism that will
need to be pressed in order to open the latches.
4. Holding the 8-port RTM by its latches, align the RTM in the MPS1000’s card guides.
5. Slide the RTM gently straight into the lower slot, keeping the RTM level. Do not apply too much
pressure, particularly if you feel resistance. You should feel the pin connectors on the rear of the RTM
meet the backplane.
6. Continue to slide the RTM into the slot until the latches touch the extrusions on either side of the slot.
40
Upgrading an 8-Port Version to a 16-Port Version
7. Press down on the latches to guide the RTM the rest of the way into the slot and lock it into place. You
will hear a click as the latches are closed and the RTM is set into place.
8. After insertion, tighten the captive screws on the latches.
9. Position the rear filler panel over the upper slot and secure the captive screws.
Upgrading an 8-Port Version to a 16-Port Version
In order to upgrade an 8-port version to a 16-port version, you must purchase the following
from Performance Technologies:
•
a second CPC358
•
a second 8-port RTM358
•
an Ethernet crossover cable
•
the proper software
See Table 2-1, “PTI Part Numbers for MPS1000 Versions and Accessories,” on page 21 for
product part numbers.
Configuring and Installing the CPC358s
After receiving the second CPC358 and the 8-port RTM358, use the following steps to
configure and install both cards.
Follow these steps to configure the CPC358:
1. Remove the filler panel on the front of the MPS1000 by unscrewing the captive screws.
2. Remove the existing CPC358 following the steps described in “Removing a CPC358,” on page 37.
3. Inspect the second CPC358. If it is new, it may come with protective plastic covers on the latches’
captive screws. These will need to be removed before the card can be installed.
Note: It is important to remember if you are updating an 8-port MPS1000 to a 16-port
MPS1000, the SW1 switch on both CPC358s must be set properly for the running
conditions of the MPS1000. Further information on setting SW1 can be found on “DIP
Switch Settings,” on page 45.
4. Set the SW1-1 switch to the Closed (ON) position on both the new CPC358 and on the existing
CPC358 in the MPS1000.
5. Insert the CPC358s following the steps described in “Installing a CPC358,” on page 39.
Installing the RTM358
Adding an additional CPC358 to an 8-port MPS1000 during the conversion to 16-port requires
the addition of the corresponding RTM358 for the second CPC358. The steps for adding the
second RTM are as follows:
Follow these steps to insert an RTM358 into an MPS1000:
1. Inspect the 8-port RTM358. If it is new, it may come with protective plastic covers on the latches’
captive screws. These will need to be removed before the card can be installed.
2. Remove the empty filler panel on the rear of the MPS1000 chassis by unscrewing the captive screws.
41
Chapter 5: On-Site Replacements and Upgrading
3. Ensure that the RTM’s latches are open. The latches have a locking mechanism that will need to be
pressed in order to open the latches.
4. Holding the RTM by its latches, align the RTM in the MPS1000’s card guides.
5. Slide the RTM gently straight into the empty slot, keeping the card level. Do not apply too much
pressure, particularly if you feel resistance. You should feel the pin connectors on the rear of the RTM
meet the backplane.
6. Continue to slide the RTM into the slot until the latches touch the extrusions on either side of the slot.
7. Press down on the latches to guide the RTM the rest of the way into the slot and lock it into place. You
will hear a click as the latches are closed and the RTM is set into place.
8. After insertion, tighten the captive screws on the latches.
9. ENET B (Ports “B”) should be connected using the supplied Crossover Cable. ENET A (Ports “A”)
should not be connected with a Crossover Cable. Using the Crossover Cable only applies to the 16port version.
Battery Instructions
The CPC358 has a lithium battery on it. The battery is user replaceable. In the event the battery
must be replaced, dispose of the battery in the proper manner.
Warning:
Do not dispose of battery in fire. Do not disassemble battery or attempt to recharge it.
42
Chapter 6
Configuration Settings
Overview
The proper configuration of the MPS1000 depends on whether you are installing one or two
CPC358 cards. One CPC358 card is needed for the 4-port and 8-port configurations, while a
second CPC358 is needed for the 16-port configuration. Installation of the CPC358 for any
configuration is the same as described in the previous chapter.
Topics covered in this chapter include:
•
“Jumper and Switch Location,” on page 43
•
“Jumper Settings,” on page 45
•
“DIP Switch Settings,” on page 45
Jumper and Switch Location
Proper configuration of the MPS1000 requires that you configure jumpers K5 and K38 and set
DIP switches SW1-1 and SW1-2 on the CPC358. The location of these jumpers and DIP
switches on the CPC358 are shown in Figure 6-1, “K5, K38 Jumpers and SW1 Switch Location
on the CPC358,” on page 44.
For more information on the location of all jumpers and switches on the CPC358, refer to the
CPC358 Octal Synchronous Serial Communications Processor Hardware Manual.
43
Chapter 6: Configuration Settings
Figure 6-1: K5, K38 Jumpers and SW1 Switch Location on the CPC358
K6
Q2
NKUBH
1
UQ27
,
V32
V34
D64
S231
DS2
D85
S254
,
S257
D84
D89
S244
S247
S248
,
S258
S25:
S261
S262
D96
S264
S265
S266
S267
D98
S268
D9:
S269
S271
S272
D87
S233
V46
K4
V39
D62
S215
S217
S222
D69
S23: UQ8
D83 UQ9
D5:
D61
D63
V38
D74
S239
D82
D7:
S237
S238
S224
D91
S252
UQ26
1
S21:
S223
S251
UQ25
P
S259
D99
M3
DS3
S246
D81
D73
7
SW1 Switch Bank
S:9
D86
S243 D8:
D97
9
6
S:4
S:6
S212
V44
S242
S253
S214
S213
TKUBH
Q4
D71 D67
UQ24
S228
S241
S249
S256
S255
S219
S218
D66
S234
S235
D77 D78
V37
5
S236
D57
D95
V45
V4:
JP7
UQ2 D53
: 21 22 23
S245
V43
P
MU7
,
SJ9
D92
D94
L38 L39
D59
S221
S226
D65
D88
V41
MU9
L37
1
SQ26
SQ27
S232
1
SQ25
D6:
S225
K5 Jumper
S:2
S:1
D93
L35 L36
SQ24
D76
V3:
D72
D75
V42
JP9
1
SQ23
D68
,
SJ4
D79
D58
,
V35
MU4
L34
S96
S95
P
V31
S227
L32 L33
SQ22
S9:
UQ3
1
QPSU2.5
S94
S93
QME!JTQ
S:8
S211
S::
D56
M5
S263
S92
S:5
S:7
V33
D55
V36
JP4
SQ21
,
SJ2
1
S99
S:3
V29
MU2
L31
SQ:
S216
S98
1
SQ9
M4
S274 V51
SQ28
SQ29
K38 Jumper
QPS
QP
S316
K2
SQ44 SQ45
S329
,
SQ46
SQ47
S34:
SQ48
SQ49
231Q1538YY
S311
D24:
SQ4:
S376
D266
Front of CPC358
E5
44
Jumper Settings
Jumper Settings
The jumper settings for the 4-port, 8-port, and 16-port MPS1000 are identical and are shown in
Table 6-1, “K5 and K38 Jumper Settings,”.
Table 6-1:K5 and K38 Jumper Settings
Pins
Jumper
1
K5
2
3
Shunted
K38
Shunted
DIP Switch Settings
DIP switch usage depends on the port configuration of your MPS1000. The only DIP switches
used for the MPS1000 are SW1-1 and SW1-2. DIP switches SW1-3 and SW1-4 are not used
and must be left Open (OFF). The location of the DIP switches on the CPC358 are shown in
Figure 6-1, “K5, K38 Jumpers and SW1 Switch Location on the CPC358,” on page 44.
4-Port Configuration
On the single CPC358, the DIP switch setting for SW1-1 must be in the Open (OFF) position
and the DIP switch setting for SW1-2 must be in the Closed (ON) position for the 4-port
MPS1000, as shown in Table 6-2, “SW1 DIP Switch Settings for MPS1000 4-Port Version,”.
Table 6-2:SW1 DIP Switch Settings for MPS1000 4-Port Version
SW1
Closed (ON)
Position 1
Position 2
Open (OFF)
X
X
Position 3
X
Position 4
X
8-Port Configuration
On the single CPC358, the DIP switch setting for SW1-1 must be in the Open (OFF) position
for the 8-port MPS1000 as shown in Table 6-3, “SW1 DIP Switch Settings for MPS1000 8-Port
Version,”. DIP switches SW1-2 through SW1-4 are not used for this configuration and must be
left in the Open (OFF) position.
Table 6-3:SW1 DIP Switch Settings for MPS1000 8-Port Version
SW1
Closed (ON)
Open (OFF)
Position 1
X
Position 2
X
Position 3
X
Position 4
X
45
Chapter 6: Configuration Settings
16-Port Configuration
For each CPC358, the DIP switch setting for SW1-1 must be in the Closed (ON) position for the
16-port MPS1000, as shown in Table 6-4, “SW1 DIP Switch Settings for MPS1000 16-Port
Version,”. DIP switches SW1-2 through SW1-4 are not used for this configuration and must be
left in the Open (OFF) position.
Table 6-4:SW1 DIP Switch Settings for MPS1000 16-Port Version
SW1
Closed (ON)
Position 1
X
Open (OFF)
Position 2
X
Position 3
X
Position 4
X
46
Index
Numerics
CPC358
configuration for upgrading to 16-port . . . . . . . . . . . . 41
configuration for upgrading to 8-port . . . . . . . . . . . . . 40
installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
jumper and switch location . . . . . . . . . . . . . . . . . . . . 43
part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
preloaded in MPS1000 . . . . . . . . . . . . . . . . . . . . . . . 20
removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35, 37
switch configuration
16-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
16-port MPS1000
cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
front view photograph . . . . . . . . . . . . . . . . . . . . . . . . .24
jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
rear view photograph . . . . . . . . . . . . . . . . . . . . . . . . .26
switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
4-port MPS1000
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
front view photograph . . . . . . . . . . . . . . . . . . . . . . . . .25
jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
rear view photograph . . . . . . . . . . . . . . . . . . . . . . . . .27
switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
upgrading to 8-port . . . . . . . . . . . . . . . . . . . . . . . . . . .40
crossover cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 42
customer support and services . . . . . . . . . . . . . . . . . . . 14
D
80-pin connector on RTM . . . . . . . . . . . . . . . . . . . . . . . .18
DB25 connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8-port MPS1000
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
upgrading to 16-port . . . . . . . . . . . . . . . . . . . . . . . . . .41
dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
E
EIA530 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
A
electromagnetic interference . . . . . . . . . . . . . . . . . . . . 35
electrostatic discharge . . . . . . . . . . . . . . . . . . . . . . . . . 31
altitude requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
ENET A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 42
ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .34
ENET B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 42
B
ESD requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ethernet ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20
battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
ethernet redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
boot PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19, 20
F
C
FCC (USA) Class A notice . . . . . . . . . . . . . . . . . . . . . . 30
cable part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
cabling on 16-port MPS1000 . . . . . . . . . . . . . . . . . . . . .26
filler panel . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 25, 26, 40
part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Canada Class A notice . . . . . . . . . . . . . . . . . . . . . . . . . .30
flash PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20
card latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
certification standards . . . . . . . . . . . . . . . . . . . . . . . . . . .29
47
G
reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
return merchandise authorization (RMA) . . . . . . . . . . . 14
grounding lug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
RoHS compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
H
RoHS part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
hard shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36, 37
RS442 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
humidity requirements . . . . . . . . . . . . . . . . . . . . . . . . . .28
RS449 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
hydra cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18, 21
RTM358
installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40, 41
part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
photograph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
J
jumper
K38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
K5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
S
safety certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
jumper settings
16-port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
4-port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
8-port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
serial I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
shared DRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20
K
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20
soft shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36, 37
K38 jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
software support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
K5 jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
storage conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
M
SW1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41, 43, 45
SW1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40, 43, 45
mounting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
switch location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
MPC8255 PowerQUICC II . . . . . . . . . . . . . . . . .18, 19, 20
switch settings
16-port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4-port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8-port MPS1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
MTBF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
O
T
operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
operating system support . . . . . . . . . . . . . . . . . . . . . . . .17
temperature requirements . . . . . . . . . . . . . . . . . . . . . . 28
P
text conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
U
part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
upgrading from 4-port to 8-port . . . . . . . . . . . . . . . . . . . 40
power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
upgrading from 8-port to 16-port . . . . . . . . . . . . . . . . . . 41
V
product warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
R
V.35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
rack mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
48
W
WAN communications protocols support . . . . . . . . . . . .17
WAN ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19, 20
warranty, product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
WEEE compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
49
50
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising