English Manual for PrismCube Ruby
Main Features
• Twin Tuner HD Satellite Receiver
• HDMI Output (up to 1080p)
• DiSEqC 1.0, 1.1, 1.2, 1.3 (USALS) Compatible
• Dolby Digital audio output (S/PDIF)
• Extended EPG and program reservation on EPG
• Open source media player XBMC with favorite addons
• Mutilingual OSD menu
• Parental Control
• Ethernet integrated
• Software update Over The Internet (OTI)
• Available in various external colors
1
What's included ?
Power Adapter
Easy Setup Guide
HDMI cable
HDD Bracket
Screws
Power Cable
2
RCU
Front Panel
Display
Standby
Displays the current menu and program information.
Top
CI Module slot
Door
open
Smartcard reader slot
One Smartcard slot is provided.
3
Rear Panel
Video/Audio Output
Ethernet
LNB INPUT 1/2
RS232
HDMI
Fan
USB
Connects to TV using a HDMI cable
for both audio and video signals.
S/PDIF
Connects to a digital audio system
using S/PDIF cable.
4
Power Adapter Input
Remote Control
STB Power
TV Power
Color Keys
SOURCE
Controls the outputs of TV.
XBMC
Displays the XBMC Media Center.
Archive
Displays the Archive window.
• Red
• Green
• Yellow
• Blue
EPG
Displays the Electronic Program
Guide (EPG) information
if provided.
Navigation Keys
i (Information)
Displays the channel and program
-me information in live mode
otherwise popup the Context menu.
Menu
Volume+/Teletext
Displays the teletext information of
the current channel if the channel
provides teletext.
Subtitle
Displays the subtitle of
the current channel
if the channel provides subtitle.
Channel+/Mute
Num Lock
Enables NUMERIC (0-9) buttons to
enter a TV/Radio channel number
or menu option number.
5
Remote Control
QWERTY
Unlock to use
NOTE
Two coin batteries (CR2032) are used
in the remote control.
The estimated battery lifetime is around 1year.
To replace batteries use a screwdriver
to pry open the lid.
1
6
2
Connecting Cable
1. Connect Satellite Signal Cable
Prismcube Ruby is a DVB-S2 Twin Tuner
Receiver. For the best use, connect two separate satellite
cables to LNB 1 & 2.
2. Connect Prismcube Ruby to the TV
One HDMI cable is included in the accessory box. Connect one end of the cable to the HDMI input
of TV. Connect the other end to the HDMI output of Prismcube Ruby.
7
Connecting Cable
3. Power Up
A power cord and an adapter are provided in the accessory box.
Plug the round end of the adapter power cord into the power input.
NOTE
AC input condition
• Nominal Voltage Range: 100 – 250 VAC
• Maximum Voltage Range: 90 – 264 VAC
• Nominal Frequency: 50 - 60 Hz
• Maximum Frequency Range: 47 – 63 Hz
8
Run First Time Installation
Prismcube Ruby is a satellite (DVB-S2) twin tuner receiver.
Please run the following installation steps for the basic system configurations.
Step 1. Run First Installation
- Press MENU and go to Installation.
- Select First Installation and press OK.
Step 2. Language Setup
- Choose the menu language and audio language.
* Prismcube Ruby
supports all major languages
to make sure its best use
in any part of the world.
Select Next and press OK to go to the next step.
9
Run First Time Installation
Step 3. Video & Audio Setup
- Configure video and audio settings from the given options.
• TV Screen Format : Normal / Stretched / Zoom
• Dolby Audio : On / Off
• HDMI Format : Automatic / 1080p / 1080i / 720p / 576p
Select Next and press OK to go to the next step.
Step 4. Antenna & Satellite Setup
Prismcube Ruby has two satellite tuners.
- Select Tuner 1 Control and choose from the below satellite signal control options :
• Simple LNB / DiSEqC 1.0 / 1.1 / 1.2 / USALS.
- Select Tuner 2 Connection and choose
from the below options :
• Loopthrough – when you have one
signal cable.
• Separated - when you have two
separate signal cables.
Select Next and press OK to go to the next step.
10
Run First Time Installation
Step 5. Channel Search Setup
This menu allows you to configure the channel search options.
- Channel Search : Yes / No
- Satellite : All or installed satellite list (e.g. Astra, Hotbird)
- Network Search : On / Off
• Off is used when searching for the default transponders only.
• On is when searching for the default transponders and additional transponders
that are not stored in the factory default transponders.
- Search Mode :
• Free only – means searching for Free-To-Air (FTA) channels only.
• Scrambled only – means searching for scrambled channels.
• Free & Scrambled – means searching for all FTA and scrambled channels.
Select Next and press OK to start the channel search.
11
Run First Time Installation
Step 6. Channel Search
You can see the progress of channel search.
When the channel search is done, the search result will be displayed.
- Press OK to complete the channel search.
- Press BACK to go to the next step.
12
Run First Time Installation
Step 7. Time & Date Setup
You can either set the time/date manually or automatically.
- Automatic – time/date is automatically set up according to the time/date information
of the selected channel.
- Manual – time/date is manually configured.
Select Next to complete the First Installation.
Step 8. Channel Search
This menu shows the summary of first installation settings.
- Menu Language
- Date
- Time
- The number of searched
TV channels
- The number of searched
Radio channels
Select Finish exiting the First Installation.
13
A Guide to Request of GPLv2 based Software
This product contains software whose rights holders license it on the terms of the GNU General
Public License, version 2 (GPLv2). You can find the text of this license in its English original version
in the manual for this product. We will provide you with the complete corresponding source code
of the software licensed under the GPLv2.
if you send us a written request by email to the following addresses:
Prismcube Support Team, support@prismcube.com
detailing the name of the product and indicating how we can contact you.
Please note that we will ask you to pay us a certain amount of money for the costs incurred.
The amount can be varied according to your location and prismcube Support Team will notify
the exact cost when receiving the request.
This offer is valid for three years from the moment we distributed the product.
In addition, you can access the source code for our devices using the command below.
git clone http://archive.prismcube.com/git/dvbapp.git
14
Now, your
Prismcube Ruby
is ready for your use!
For more information about Prismcube Ruby,
go to "Help" from Main Menu.
15
Prismcube Ruby
XBMC Integrated Hybrid Linux Receiver
www.prismcube.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising