SXS8A PD3V100-Q.cdr - Strumenti Musicali

SXS8A PD3V100-Q.cdr - Strumenti Musicali
ICON
©
=
=
©
=
D
So
©
=
O
SX-Sub8A
8" Active Studio Subwoofer System
GRUNE Pe,
@ (€ Hones ©
000
°° O. o
©:
9
090
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
O NOT REMOVE COVER (OR BACK)
NO USER-SERVIDEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
ATTENTION: POUR EVITER LES RISQUES DE CHOC
ELECTRIQUE: NE PAS ENLEVER LE COUVERCLE. AUCUN
ENTRETIEN DE PIECES INTERIEURES PAR LUSAGER.CONFIER
L'ENTERETIEN AU PERSONNEL QUALIFIE.
AVIS: POUR EVITER LES RISQUES D'INCENDIE OU
D'ELECTROCUTION, N EXPOSEZ PAS CET ARTICLE
The lightning flash with arrowhead symbol within an
equilateral triangle.is intended to.alert the user to the
presence of uninsulated dangerous voltage within the
products enclosure, that may be of sufficient magnitude to
electric shock to persons. Le symbol.clair avec point de fi
che lintrieur d un triangle quilat ral est utilis pour alerter
| utilisateur de la pr sence | int rieur du coffret de vottage
dangereux non isol d ampleur suff
exclamation point within an equilateral triangle is
intended to alert the user of the presence of important
operating and maintenance (serviving) instructions in the
literature accompanying the appliance. Le point
d'exclamation | int rieur d un triangle quilat ral est employ
pour alerter les utilisateurs de la prseace d instructions
importantes pour le fonctionnement et | entretien (service)
dans le livret d instruction accmpagnant | appari |.
ALA PLUIE OU A L'HUMIDITE
Important Safety Instructions
1. Read this manual thoroughly before using this unit.
2. Keep this manual for future reference.
3. Take notice of and comply with all warnings included in the user's manual or indicated
on the appliance.
4. Follow all instructions included in this manual.
5. Do not expose this unit to rain or moisture. Avoid having water or other liquids spilled
on this unit.
6. When cleaning the cabinet or other parts of this appliance, use only a dry or slightly
damp soft cloth.
7. Do not block any ventilation openings or interfere with the proper ventilation of this unit.
Install in accordance with the manufacturer's instructions.
8. Do not use or store near any heat sources such as radiators, heat registers, stoves, or
other heat-producing appliances.
9. Do not interfere with the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding-type plug h
as two blades and a third grounding prong. These are designated for your safety. If the
provided plug does not fit into your outlet, consult an electrician.
10. Protect the power cord from being walked on or otherwise damaged by items placed
on or against them. Particular attention should be given to the plugs, receptacles, and
the point where the cord exits the appliance.
11. To avoid the risk of electrical shock, do not touch any exposed wiring while the unit is
in operation.
12. Only use attachments/accessories specified by the manufacturer.
13. Unplug this unit and all connected electrical equipment during lightning storms or when
left unused a long period of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
appliance has been damaged in any way or fails to operate normally.
WARNING: To reduce the risk of fire or electric shock, do not expose this unit to
rain or moisture
monitor
Contents
Introduction
What's in the package
Intended USe ee,
Feature eee nen nn
Rear Panel Layout ee)
Controls and Connections...
Setting Up your SX-Sub8A Subwoofer System...
Settings and Adjustments... неее
Specifications........................................ es
SO VIC OS 00e
Introduction
Congratulations on purchasing your ICON SX-Sub8A Studio Subwoofer
system. The management and employees of ICON are dedicated to
producing quality equipment and are pleased that you have selected one of
our many fine products. With proper care, we trust that your SX-Sub8A
Studio Subwoofer will provide years of trouble-free operation.
This manual is intended to introduce you to the features and specifications
of the SX-Sub8A Studio subwoofer you have purchased and to guide you ment
through the proper set-up and use of this equipment. You will also find an
enclosed warranty card. Please fill it out and mail it in to receive online
technical support and updated information about this unit as well as other
quality ICON products.
We recommend that you record your serial number in the space below for
future reference.
Welcome to ICON, and thank you for becoming part of our worldwide family!
Please write your serial number here for future reference:
Purchased at:
Date of purchase:
What's in the package?
e SX-Sub8A Active Subwoofer System
e Users’ Manual
e Power Cable
Intended use
The ICON SX-Sub10A Studio Subwoofer system is a loudspeaker with an
integrated amplifier for the reproduction of the deepest audio frequencies.
This product has been specifically designed and developed for use in a
professional studio environment. The reliability and performance of this
product cannot be guaranteed for other applications or uses.
Features
monitor
The ICON SX-Sub8A Active Studio Subwoofer system provide a powerful and
precise low-frequency reproduction. Here are some of its main features:
e 8" Woofer
® Phase adjustment in 0’ / 180°
e 30-150 Hz precision low-frequency reproduction
® LFE - Slave mode selectable
e Low Pass filter control ranged from 50Hz - 150Hz
e Subwoofer output level control (gain)
e Sat/Sub I/O connectors for right and left channel
® Unbalanced RCA output connectors
e 150W power handling @ 8 Ohms
® Studio cabinet ideal for professional applications
Rear Panel Layout
High Pass
80Hz Flat
60Hz HP
n Out
R L
Low Pass
fo
Phase
180°
Gain
INL IN
(ON (OO)
EY
50Hz 150Hz Mi
Mode
LFE
O ©®
Studio Series 8" Active Studio
Subwoofer System
Warning
This equipment is capable of delivering sound
pressure levels considerably high, which may
| cause permanent damage to your ear.
`.
( Q CAUTION f |
Risk of electrical shock
Do not open
Risque de shock electrique
Ne pas ouvrir
DE.
‘CAUTION: TO RED!
DO
e
@ AC In
Main power input
@) Voltage Selector
110V / 220V input voltage selector
(3) Power Switch
Turns the unit on/off.
monitor
monitor
Controls and Connections
SAT/SUB
. Pass = Pass
f
80Hz Flat
(7
N
N
50Hz 150Hz Min Max
Phase Mode
180° LFE
®® ©
SAT/SUB o.
Input for full bandwidth signal. The signal is processed according to
the High Pass setting and provided at the SAT/SUB Output.
SAT/SUB Output (Balanced)
Output to connect a satellite loudspeaker system. Signal is
processed according to the High Pass setting.
LFE/Slave Input
Input for LFE signal (Low Frequency Effect)
Slave Output
Output to next subwoofer (if installed)
High Pass Selectors
Allows cutting off low frequencies of the signal provided to the
SAT/SUB Output terminal. If "Flat" is selected, the signal is not
limited. If "HP" is selected, signal is cut off at 50 HZ or 80 HZ
(according to selection).
Unbalanced Output
Output to connect a satellite loudspeaker system.
Low Pass Selector
Controls the subwoofer low pass frequency continuously variable
from 50 to 150 HZ.
Phase Selector
phase can be set to 0° or 180°
Gain
Main volume control
Mode Selector
Select "LFE" for normal and Master use. Select "Slave" setting for
second and all following subwoofers.
Setting up your SX-Sub8A Subwoofer System
Input Connection Options
Your SX-Sub8A Subwoofer features inputs for two different signal
types.
LFE /Slave Input Allows connection to a LFE channel
(Low Frequency Effect).
SAT/SUB Input Allows connection of a full bandwidth signal.
Signals connected via the LFE/Slave Input is processed and
reproduced by the subwoofer and routed to the Slave Output for
connection to a second subwoofer.
Full bandwidth signals at the SAT/SUB Input are reproduced by the
subwoofer and routed to the SAT/SUB and the Slave Output terminals
with frequencies cut off according to the High Pass and Low Pass
settings. Use the SAT/SUB Output Terminal for connection to a power
amplifier or active speakers.
Basic Set-up and Operation
(® Before connecting your SX-Sub8A subwoofer, make sure that the
power of all your system components is turned off. Also, turn the
main volume control (gain) on your subwoofer all the way down.
(2) Set the Mode switch on your subwoofer to LFE (Note:
If connecting more than one subwoofer, the first
subwoofer will be set to LFE. Set the Mode to "Slave"
for the second and all subsequent subwoofers.)
© Connect LFE Channel to the LFE/Slave
Input on your subwoofer. Connect full
bandwidth signals to the SAT/SUB
Input.
(4) After all instrument, speaker, and
component connections have been made,
turn on your subwoofer and other powered
components.
(® Slowly raise the volume on your SX-Sub8A
subwoofer to the desired level by adjusting the
Gain control.
monitor
Setting up your SX-Sub8A Subwoofer System
Multiple Subwoofer Set-up
Connecting multiple subwoofers may be desired in large studios or
other spaces featuring difficult acoustic conditions. SX-Sub8A
subwoofers can be easily linked by connecting the Slave Output
terminal on the first unit to the LFE/Slave Input on the second terminal,
fui and so on.
The first subwoofer will act as the "Master" and should be set up as
indicated on page 5 (and the diagrams showing below), with the Mode
set to "LFE." Set the mode to "Slave" on each additional subwoofer.
First Subwoofer Additional Subwoofer
Note: when using multiple subwoofers, the volume and phase settings
of the Master will control all subwoofers.
Loudspeaker Connection
To connect loudspeakers to your subwoofer, use the SAT/SUB Output
terminals to connect an XLR cable to the input on your power amplifier.
(Be sure to note the manufacturer's instructions and specifications for
proper amplifier and speaker set-up).
LL” SATISUB \
e
Left Active Right Active
Monitor Monitor
Speaker Speaker
Settings and Adjustments
Low Pass setting
The Low Pass control defines the frequency range of the Low Pass
subwoofer and cuts off frequencies above the selected :
level. Frequencies above the selected level are routed to
the SAT/SUB Output while those below the Low Pass
setting are reproduced by the subwoofer and available
at the Slave Output Terminal.
The correct setting of the Low Pass control is important to ensure
balance between the subwoofer and speakers. Adjust the Low Pass
setting to the desired level between 50 and 150 HZ.
Note: Only signals at the SAT/SUB Input are affected by the Low Pass
control.
High Pass setting
The bass capabilities of satellite speakers can potentially
overlap the frequency range of your subwoofer. Poor High Pass
sound quality can result when the system is not matched | so: Fa!
properly or when using small speakers or low-powered
amplifiers. The High Pass filter can be used to limit the вон: L— Hp
bass range of speakers connected via the SAT/SUB
Output terminals.
SX-Sub8A subwoofers are equipped with three High Pass settings:
Flat No limitation
50 Hz Frequencies below 50 Hz are cut off
80 Hz Frequencies below 80 Hz are cut off
To select the desired High Pass setting, first choose between "Flat" or
"HP" (High Pass). If "HP" is selected, choose the preferred cut-off
frequency 50 Hz of 80 Hz.
Phase Setting
(M Set up your system components as described above
@) Play a bass-rich soundtrack that includes frequencies
in the overlap
@ Switch the Phase Setting between 0° and 180° to
find which setting provides the most bass.
monitor
monitor
Specifications
System:
Bass principle:
Frequency reponse:
Inputs
e LFE/Slave:
e SAT/SUB:
Input Impedance
+ barnch:
- branch:
Sensitivity:
Max. input voltage:
Outputs
® Slave:
e SAT/SUB:
Output impedance:
XLR Connector:
Mode selector:
Phase adjustment:
High pass:
Low pass:
Power modes:
Amplifier power:
Power Consumption
e Standby:
e Max.:
Woofer
e Cone:
e Coil:
Dimensions:
Cabinet volume:
Weight:
Main:
Active subwoofer
Bass reflex
30Hz to 150Hz
XLR
Right/Left full bandwidth, XLR
20K Ohm
10K Ohm
75mVrms to 5Vrms , adjustable
8 Vrms
XLR
Right/Left, Highpass filtered, XLR & RCA
100 Ohm (each branch)
Pin 1: 0 / Pin 2 : + / Pin 3 : -
LFE & Slave
09/1809
Flat / 60Hz / 80Hz
50 Hz to 150 Hz
On / Auto
120W, 4 Ohm
<5W
250W
204mm / 8", long throw, paper cone
35mm / 1.4" voice coil
310(H) x 290(W) x 360(D) mm
10.2(H) x 9.6(W) x 11.9(D) inch
22 liters
17 Kg
120V, 50/60Hz
220V, 50/60Hz
Services
If your SX-Sub8A needs servicing, follow these instructions.
1.
Ensure the problem is not related to operation error or external
system devices.
Pack the unit in its original packaging including end card and box.
This is very important. If you have lost the packaging, please
make sure you have packed the unit properly. ICON is not
responsible for any damage that occurs due to non-factory
packing.
Contact your ICON dealer or if none is available, contact the
nearest ICON distributor or regional office to obtain a return
authorization. If applicable, shipping instructions will be provided
by the dealer or from ICON.
Refer to www.icon-global.com for a complete list of current ICON
distribution locations.
U.S. OFFICE:
ICON Digital Corporation.
2222 Pleasant View Road,
Suite #1 Middleton,
WI 53562
Tel: 608-829-3450 Fax: 608-829-1972
infous@icon-global.com
ASIA OFFICE:
ICON International Digital Limited
Suite Nos. 7-10,
8th Floor, Sunley Centre,
No.9 Wing Yin Street,
Kwai Chun. N.T.
Hong Kong
Tel: 852-2398-2286 Fax: 852-2789-3947
infoasia@icon-global.com
For additional update information please visit our website at:
www.icon-global.com
monitor
Notes
monitor
o
O
090%
О
9900
=
©
ICON
www.icon-global.com
info@icon-global.com
SXS8A PD3V100
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising