BALEVER

BL380WM

Forest Cameras

120° wide lens/0.6s Trigger/1080P HD/GPRS MMS

User Manual

Introduction

Congratulations on the purchase of your new device. You have selected a high-quality product. The operating instructions are a constituent of this product. They contain important information about safety, use and disposal.

Before using the product, familiarise yourself with all operating and safety instructions. Use this product only as described and only for the specified areas of application.

Main features

♦

120 degree wide angle lens

♦

1080P full HD video resolution

♦

0.6 seconds trigger time

♦

IP65 waterproof, dustproof

♦

6-8 months stand-by time (4-12 batteries)

♦

MMS function

Illustration

Front&Bottom view:

Power supply

♦

To insert batteries in the device, first open the base plate and pull out the battery compartment.When you replace the battery, please replace all batteries. Do not mix using the old and new batteries together.

♦

Insert 4 x 1.5 V LR6/AA batteries into the battery slots .

Please pay close attention to the polarity, which is marked on the battery compartment. Otherwise the device will not work and can be damaged.

♦

To increase the operating time, you can use an additional 4 x 1.5 V LR6/AA batteries in the battery compartment.

♦

If you operate the device using a mains adapter (not supplied), open the round rubber seal on the base plate and connect the plug of the adapter cable into the socket for the external mains adapter, which is now accessible. The mains adapter must supply a direct-current voltage of 6 V. Use a barrel jack whose interior polarity is connected to the plus pole. Operation via a mains adapter is possible with batteries inserted. If one power source fails, operation will be maintained using the other.

Inserting storage media

►

Since the camera has no built-in memory, it can only work if an SD/SDHC memory card is inserted.

After inserted, format the SD card , so that to improve the battery life and shutter speed.

►

The device supports SD/SDHC memory cards with a capacity of up to 32 GB.

►

To avoid malfunctions, keep the memory card away from moisture and avoid strong vibration, dust, heat sources and direct sunlight.

►

Insert the memory card as indicated by the icon on the slot.

Never force the memory card into the slot. Never bend or twist the memory card.

►

After transport, wait until the memory card has reached ambient temperature before using it for the first time. Major fluctuations in temperature or humidity can lead to condensation which could cause an electrical short-circuit. Keep the memory card in the protective case.

►

When the SD memory card is full, it will automatically stop take picture and record video. And the light will be closed.

♦

To remove an SD/SDHC memory card from the memory card slot of the device, press the protruding edge of the memory card in a little way until it pops out. Then remove the card.

♦

To insert an SD/SDHC memory card into the memory card slot of the device, push it into the slot until it clicks into place. The contact surfaces of the memory card must be facing towards the front of the camera.

♦

SD/SDHC memory cards have a locking system to prevent accidental erasure. To protect the card from write access, slide the switch on the side of the card to the“LOCK”position. However, the camera can only save data onto the card if the switch is in the other position.

Specifications

Image sensor

Photo resolution

Video resolution

File format

Lens

Display

External memory

Range of IR flash

Triggering distance

PIR Sensitivity

Trigger time

Trigger Interval

Shooting Numbers

Effectiveness

Video Length

Camera+Video

Time Stamp

Time Lapse

MMS Status

MMS Numbers

MMS Phone No.

5MP CMOS sensor

12MP / 8M / 5M / 1.3M

1920*1080P/30fps;

1280x720/30fps 720x480/30fps; 640x480/30fps

JPG/AVI

F=3.1; FOV=120°; Auto IR-Cut

2.0" TFTLCD

TF card up to 32GB

65 Feet/20 Meters; 30 Feet/10 Meters on

Low-glow Flash

20m（ Below 77°F/25°C at the Normal Level）

High/Normal/Low

0.6 Second(When using the 4G SD card)；

Pre boot 0.2 Sesond

5sec. - 60min;Programmable

1-2-3

Daytine:1m-infinitive;Night time:3m-20m

5-30sec.;Programmable

First take Picture then Video

On/Off;Include serial No.,temperature and moon phase

On/Off; Time Lapse Programmable

VGA = 640x480; QVGA = 320x240;OFF

Programmable

“0” = Unlimited; 0 ~ 99/Day

1 Phone Numbers

MMS E-mail

Language

Password

Build-in Microphone

Build in Speaker

1 E-mail addresses

English/French/Spanish/Portuguese/Deutsch/

Italian/Chinese/Japanese

4-Digit Numbers

Yes

Yes

Auto-distinguish images Color images in daytime/black & white night images

Auto Power Off

TV-out

PC Interface

Auto power off in 3 minutes while no keypad controllin g

Yes

Mini USB2.0

Power supply

4xAA;Expandable to 12xAA external 6V power supply,at least 2A

Standby time

Spray-water protected

Operating Temperature

Certificate

Applications

1. Trail camera for hunting

6-8 months

Yes (IP protection class56)

-20℃ to +60℃

CE/ROHS/FCC

2. Animal or event observation,Fauna Surveys

3. Warehouse/Storage/Farm Area Surveillance

4. Home/Property Security

5. Farm Gates or Driveways

Accessories

1. strap

2. USB cable

3. User manual

Transferring recordings to a computer

Connect the mini USB plug of the supplied USB cable to the USB port on the camera and the USB plug to a free USB 2.0 port of a switched-on computer. This will now recognize the device as“mass storage”. When you have confirmed this message of the camera with“OK”, the camera connects to the computer and the content of the SD/SDHC memory card will appear as a new drive on the computer. Now carry out the required file operations.

Cleaning

Damage to the device!

►

To avoid irreparable damage, ensure that no moisture penetrates the device during cleaning.

■ Clean the surfaces of the device with a soft, dry cloth. Use a normal commercial detergent and water to remove stubborn residue. Ensure that no water gets into the device.

■ Always keep the seal between the camera housing and the tree mounting clean so that no moisture gets into the device and damages it. Contamination of the seal can impair the dust and water spray protection .

■ Always keep the base plate seal that protects the connection socket for the mains adapter clean.

■ Clean the seal regularly with a little Vaseline to keep it malleable. This is the only way to ensure that the interior of the device is adequately protected from moisture.

Handling and operation

In this chapter you will receive important information for the handling and operation of the device.

Switching on and off , making settings

After connecting a power supply, move the operating mode selector switch to the“TEST”position to make the settings described on the following pages using the remote control panel buttons (photo as follows). In test mode, the infrared lamp is closed.

Press the key to choose the upper option.

Press the key to choose the next option.

Press the SHOT key to manually trigger the shutter. A photo or video (depending on the camera setting) will be taken and saved to the SD card.

Press OK key to save the menu setting

Press Mode key to swift photo mode and video mode; review or replay the photo or video; swift the number, letter, symbol when setting up MMS.

The Menu on the keypad allows you to program the camera to work the way you want.

How to finish the Parameter by the remote control.

1.Mode

To select whether photos or videos are to be recorded in motion detection mode. In “Photo + Video” mode, the camera first takes a photo and then starts filming video.

2.Language

Here you can set English / French / Spanish / Portuguese / Dutch/ Italian / T Chinese / S

Chinese/Japanese as the menu language. Contact the manufacturer if you want to add any new language.

3.Image size

Select a photo size: 1.3 MP, 5 MP (preset), 8 MP or 12 MP.The larger the file size, the more detailed the image. However, the maximum number of high-resolution images that can be stored before the memory card is full is much lower.

4.Video resolution

Select the screen resolution: 1920 × 1080, 1280 × 720, 640 × 480. The higher the resolution, the sooner the capacity limit of the memory card will be reached.

5.Date & time

Press OK to set up date and time. They will be displayed on the photos that the camera takes.

6.Shooting No.

Select the number of photos that are to be taken in succession when the camera is activated in photo mode. In addition to single shot mode 1 photo, you can take“2 photos”or“3 photos”.

7.Video length

Use the up/down buttons to select the length of the video recording (between 5–30 seconds) that is to be made when video recording is activated. The longer the recording time selected, the shorter the operating time.

8.Interval

Use the up/down buttons to select the minimum time period(between 3second and 60mins) that the camera should wait before reacting to subsequent activation of the sensor after the initial recording.

During the selected interval, the camera will not record any images or videos. This prevents the memory card from being filled up with too many recordings of the same event. You can select between 3 seconds to 60 minutes.

9.PIR Sensitivity

The sensitivity of the main motion sensor is set here. For interior areas and environments with little interference, such as branches blowing in the wind, select“High”. Select“Medium”for exterior areas and environments with a normal amount of interference, and select“Low”for environments with a high level of interference. The temperature can also affect the sensitivity. The“High”setting is suitable for warm ambient temperatures, whereas“Low”should be selected for cold environments.

10.Date stamp

Here you can choose whether to save your photos with a time stamp.You can choose whether the stamp consists of the time and date or just the date.

11.Timer

Select“On”if the camera should only be active during a certain time period. In the screen menu that subsequently appears, you can then set the start and end time for the active phase:

Press the up/down buttons to set the hour for the start of the active phase. Then switch to the next field using the right button. Press the up /down buttons to set the minutes for the start of the active phase.

The settings made here apply every day. The camera will not record any images outside of the active phase.

Confirm your selection with the OK button. Afterwards, press the MENU button to close this sub-menu.

12.Password Setting

Select “On”if you want to use a password to protect the camera from unwanted access. In the following screen menu, you can set a 4-digit combination:

Press the up /down buttons to select the first digit between 0–9.

Then switch to the next field using the right button. Press the up /down buttons to select the second digit between 0–9.Confirm your selection with the OK button. Afterwards, press the MENU button to close this sub-menu.The set number combination must now be entered each time the camera is switched on in SET mode before the unit can be operated.If you forget the number combination, please ask the supplier for firmware to reset it to its factory default settings.

13.Serial No

Select“On”if you want to use a serial number to rank the camera. In the following screen menu, you can set a 4-digit combination:

Press the up /down buttons to select the first digit between 0–9.

Then switch to the next field using the right button. Press the up /down buttons to select the second digit between 0–9.

14.Time lapse

With this function the camera automatically takes pictures at adjustable intervals. This is useful if you want to observe the blooming of plants or the like, for example. When you confirm“On”with the OK button, you can then set the desired time interval using the menu that now appears:

Press the up/ down buttons to set the hour of the desired time interval.Then switch to the next field,“Min

”, using the right button. Press the up/down buttons to set the minutes of the desired time interval. Then switch to the next field,“Sec”, using the right button. Press the up/down buttons to set the seconds of the desired time interval.Confirm your selection with the OK button. Afterwards, press the MENU button to close this sub-menu.

15.Organization Name

The default setting is Off. The user can set up the logo or label on the photo that the camera takes

16.MMS setup

Input the operator data of the SIM card you are using in the camera to send MMS photos: APN, MMSC

URL, IP, Port, Account (if needed). Password (if needed), phone number and email address to receive the photo.

17.MMS status

Choose either VGA=640x480 or QVGA=320x240, which defines the resolution size of the MMS picture.

18.Record audio

Open the function, you can record sound while recording video.

19.Default Settings

If you select“Yes”the menu item and then slide the select bar in the following prompt to“OK”using the

/ buttons and then press the OK button, all previously made camera settings including any password will be deleted and the factory settings will be restored.

20.Format

Formatting the memory card will permanently delete all data on it. Before you use a new memory card in the camera or a card that has previously been used in another device, you should first format the memory

card. Select“Yes”with the OK button and confirm the following prompt with the OK button. The formatting process starts. While the card is being formatted, the message “Please wait”appears.

21.Version

Check the Software Version number.That’s will be help to the manufacturer to find our the reason when the camera with problem.

How to finish the Parameter via PC firmware.

a.Mode

To select whether photos or videos are to be recorded in motion detection mode. In “Photo + Video” mode, the camera first takes a photo and then starts filming video.

b.Language

Here you can set English / French / Spanish / Portuguese / Dutch/ Italian / T Chinese / S

Chinese/Japanese as the menu language.

Contact the manufacturer if you want to add any new language.

c.Image size

Select a photo size: 1.3 MP, 5 MP (preset), 8 MP or 12 MP.

The larger the file size, the more detailed the image. However, the maximum number of high-resolution images that can be stored before the memory card is full is much lower.

d.Video size

Select the screen resolution: 1920 × 1080, 1280 × 720, 720 × 480, 640 × 480. The higher the resolution, the sooner the capacity limit of the memory card will be reached.

e.Video length

Use the up/down buttons to select the length of the video recording (between 5–30 seconds) that is to be made when video recording is activated. The longer the recording time selected, the shorter the operating time.

f.Interval

Inpute the minimum time period(between 3second and 60mins) that the camera should wait before reacting to subsequent activation of the sensor after the initial recording. During the selected interval, the camera will not record any images or videos. This prevents the memory card from being filled up with too many recordings of the same event. You can select between 3 seconds to 60 minutes.

g.Shot number.

Select the number of photos that are to be taken in succession when the camera is activated in photo mode. In addition to single shot mode 1 photo, you can take“2 photos”or“3 photos”.

h.PIR Sensitivity

The sensitivity of the main motion sensor is set here. For interior areas and environments with little interference, such as branches blowing in the wind, select“High”. Select“Medium”for exterior areas and environments with a normal amount of interference, and select“Low”for environments with a high level of interference. The temperature can also affect the sensitivity. The“High”setting is suitable for warm ambient temperatures, whereas“Low”should be selected for cold environments.

i.Date stamp

Here you can choose whether to save your photos with a time stamp.You can choose whether the stamp consists of the time and date or just the date.

j.MMS status

Choose either VGA=640x480 or QVGA=320x240, which defines the resolution size of the MMS picture.

k.Record audio

Open the function, you can record sound while recording video.

l.Timer

Select“On”if the camera should only be active during a certain time period. In the screen menu that subsequently appears, you can then set the start and end time for the active phase:

Input the hour and minute for the start/end of the active phase. Confirm your selection with the “OK” button and to close this sub-menu.

The settings made here apply every day. The camera will not record any images outside of the active phase.

m.Password Setting

Select “On”if you want to use a password to protect the camera from unwanted access. In the following sub-menu, you can set a 4-digit combination:

Confirm your selection with the “OK” button and close this sub-menu.

The set number combination must now be entered each time the camera is switched on in SET mode before the unit can be operated.

If you forget the number combination, please ask the supplier for firmware to reset it to its factory default settings.

n.Serial No

Select“On”if you want to use a serial number to rank the camera. In the following sub-menu, you can set a 4-digit combination:

Confirm your selection with the “OK” button and close this sub-menu.

o.Time lapse

With this function the camera automatically takes pictures at adjustable intervals. This is useful if you want to observe the blooming of plants or the like, for example. When you confirm“On”with the OK button, you can then set the desired time interval using the menu that now appears.

Inpute the hour/minute/second of the desired time interval.

Confirm your selection with the “OK” button and close this sub-menu.

p.Organization Name

The default setting is Off. The user can set up the logo or label on the photo that the camera takes

Confirm your selection with the “OK” button and close this sub-menu.

q.MMS / SMPT Setup

Choose your country and operator in this sub-menu to finish the MMS(MMS/SMTP/Both) setup.

r.Default Config

all the setting data will be recovery to the factory setting after you click this key.

s.Load Config File

Load the config from your SD card(that was made before)

u.Save config no:

Input your SD card to the computer at first,then click the “save config no” to save the data to your SD card.There will be a “menu.cfg”file in your SD card.all the data that you set will be show on the camera display after you input the SD card to your camera.

V. Exit

Exit the system