BC820v2H3 - Quick Start Guide

BC820v2H3 - Quick Start Guide
Siqura BC820v2H3
Find additional manuals for this Siqura product
at: www.siqura.com/support-files
3Mpixel box camera with integrated optics
Quick Start Guide
Unpack
Power up / Connect
Install
Determine where you are going to install the camera.
To power the BC820v2H3 with PoE


Use the Siqura WM04 Wall Bracket sold separately for BC series cameras
(figure 2).
Attach the RJ-45 connector to an appropriate PoE
network switch.

Make sure that the provided surface has sufficient strength to support the camera.

If using Power over Ethernet (PoE), check that there is adequate access to an IEEE
length. Connect to hub/switch with straight-
802.3af Power Sourcing Equipment (PSE) enabled network
through; direct to a PC with crossover.

Use Cat 5 Ethernet cable less than 100 m in
To power the camera with AC 24 V / DC 12/24 V

Connect to the DC/AC power source as indicated
Figure 3 BC820v2H3 rear
board connectors
by the labeling of the terminal block.
+
-
AC 24 V: Power-1
DC 12/24 V Power
AC 24 V: Earth GND
Earth GND
AC 24 V: Power-2
DC 12/24 V GND
Table 1
AC 24 V / DC 12/24 V
connection assignments
Indicator LEDs

RJ-45 connector LEDs: Green indicates a good network connection; orange
verifies network activity.

Figure 1 Package contents
Note: Subject to modification. Actual product and accessories may differ in appearance.
Log on
Green power LED signifies a good power connection.
To reset the camera to the factory default settings
Figure 2 The BC820H1 screws onto a mounted wall bracket
Install Siqura Device Manager (optional)

With the camera powered up, push and hold the reset button for 30 seconds.
Access via Siqura Device Manager (optional)
You can access the settings of the camera via its web interface.
Use Internet Explorer, to browse the webpages.
To open communication with the BC820v2H3
1.
Make an IP connection between the camera and the PC.
1
To achieve initial access, the network adapter of the PC must be set to the same
BC820
BC820v2H3
subnet as the camera. The factory-set IP address is on a label on the bottom of
the camera.
2.
Type the IP address of the camera in the address bar of your web browser.
3.
Enter the default user name (Admin) and password (1234).
1
2
Note that the user name is case sensitive.
4.
When prompted by the camera, install the add-on, Siqura Viewer.
5.
Enable ActiveX controls.
2
CAUTION: MAKE SURE THAT YOU CHANGE THE DEFAULT ADMIN PASSWORD AT
THE FIRST LOGIN. TO KEEP THE ACCOUNT SAFE, CREATE A STRONG, COMPLEX
PASSWORD. THIS HELPS TO PREVENT UNAUTHORISED ACCESS FROM PEOPLE
WHO TRY TO USE THE DEFAULT ACCOUNT.
3
Figure 4 Enter the IP address of the camera into the address bar of your browser
© Siqura B.V. 2016
Version 1.0 (161107-1.0)
BC820v2H3 QSG (MW10)
Figure 5 Download siqura Device Manager at www.siqura.com/support-files.
Install the software on the browsing PC.
www.siqura.com
www.tkhsecurity-usa.com
Figure 6 Use Siqura Device Manager to open the webpages of the camera
Change the network settings
With Siqura Device Manager you can directly change the network settings of
Across the top of the BC820v2H3 home page are six main menu items.

Home
Here you can monitor a live video stream or double-click the image to view
To change the network settings
10.50.3.145
stream details.
Right-click the camera in Siqura
10 . 50 . 3 . 145
Device Manager.

System
255 . 0 . 0 . 0
2.
Click Change Network Settings.
3.
Click Enable DHCP.
Here you can set the host name, system time, root password, and other
10 . 50 . 1 . 3
network related settings.

- or -
Streaming
Here you can set video and audio formats and compression parameters.
Click Static IP, and then enter the

new IP address, subnet mask, and
Camera
Here you can adjust various camera settings, including exposure, white balance,
gateway address.
4.
Depending on how BC820v2H3 camera is mounted, you may need to rotate
the camera image.
the camera
1.
Rotate camera image
Navigate the webpages
Click OK.

Figure 9 Applying Mirror video rotation
brightness, sharpness, contrast, and digital zoom.
To select a video rotation type
Pan Tilt
1.
With a Pan Tilt head properly connected to the RS-485 port of the camera, the
Figure 7 Network settings
user can drag the pointer across the camera view in the webpages for pan/tilt
On the Streaming tab, click to select Video Format from the menu options on
the left.
2.
Choose one of the following video rotation types:
camera control.

Normal video. The camera’s orientation is not modified.
Logout
Note: A DHCP server must be installed on the network in order to apply DHCP network

Flip video. The image rotates across the horizontal axis.
The Logout option signs the user out of the camera’s webpages and opens the
support.

Mirror video. The image rotates across the vertical axis.
Login page.

90 degree clockwise. The image rotates 90° clockwise.

180 degree rotate. The image rotates 180°.

90 degree counterclockwise. The image rotates 90° counterclockwise.

You can also change these settings on the Network webpage of the camera. For more
information, see the User Manual.
3.
Figure 8 The BC820v2H3 web interface menus
Set up alarms
Connect audio
If microphones and speakers are implemented, the camera can be used to
Connecting an alarm device, such as a sensor, to the BC820v2H3 camera input
provide a two-way audio channel.
can trigger an output action to occur based on digital I/O settings. A motion
detection or tampering alarm can also trigger an output action.
Step 1: Connect the audio input and output
cables to the LINE IN and LINE OUT
Step 1: Connect the alarm relay
Step 2: In the camera webpages, go to the
connectors on the back of the camera.
connectors to the I/O terminal block
System > Events tab. Using the Application,
on the back of the camera.
Motion Detection, and Tampering pages,
configure the alarms as desired.
Figure 10 Audio in and out connectors.
Pin definitions
Step 2: In the camera webpages, go to Streaming > Audio and select one of the

time. Local and remote sites can communicate with each other

Half-duplex – Audio can be either transmitted or received. One site
can talk or listen to the other site in turn.

Simplex (Talk only) – Audio can be transmitted. One site can speak to
the other site.

Simplex (Listen only) – Audio can be received. One site can listen to
the other site.

Disable – The audio transmission function is turned off.
Solid state relay MOSFET
output
Full-duplex – Audio can be transmitted and received at the same
simultaneously.
Output specification

following options:

Equivalent circuits
Absolute MAX voltage:
300 V AC/DC
1.
Output+

ON-Resistance: MAX 30 Ω
2.
Output-

MAX Load Current: 100 mA
3.
Input+

OFF Leakage Current: 1 uA
4.
Input-
5.
GND
6.
RS-485 D-
7.
RS-485 D+
Table 2 Alarm definitions
Click Save to confirm settings.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising