Copper SFP Series

Copper SFP Series
EOLT-C03-02-X & EOLT-C02-02-X Series
10/100BASE-T Copper SFP Transceiver
RoHS6 Compliant
Features
Support 10/100BASE-T Operation in
Host Systems
For 100m Reach over Cat 5 UTP Cable
Hot-Pluggable SFP Footprint
Fully metallic enclosure for low EMI
Low power dissipation
Compact RJ-45 connector assembly
Applications
Detailed product information in
EEPROM
LAN 10/100Base-T
Operating Case Temperature
Router/Server Interface
Switch to Switch Interface
：℃ ℃
Industrial：-40℃~85℃
Standard 0 ~70
Switched backplane applications
Compliant with SFP MSA
Compliant with IEEE Std 802.3
Order Information
Data
Rate
Link
Type
Connector
LOS
Function
EOLT-C02-02
10M
Cat5
RJ45
Without
100m
Standard
EOLT-C02-02-I
10M
Cat5
RJ45
Without
100m
Industrial
EOLT-C03-02
100M
Cat5
RJ45
Without
100m
Standard
EOLT-C03-02-I
100M
Cat5
RJ45
Without
100m
Industrial
EOLT-C03-02-A
10/100M
Cat5
RJ45
Without
100m
Standard
EOLT-C03-02-AI
10/100M
Cat5
RJ45
Without
100m
Industrial
EOLT-C02-02-E
10M
Cat5
RJ45
With
100m
Standard
EOLT-C02-02-EI
10M
Cat5
RJ45
With
100m
Industrial
EOLT-C03-02-E
10/100M
Cat5
RJ45
With
100m
Standard
EOLT-C03-02-EI
10/100M
Cat5
RJ45
With
100m
Industrial
Part No.
Eoptolink Technology Inc., Ltd.
Page 1 of 8
Distance Tempe.
V1.f
Copper SFP Series
Regulatory Compliance*
Product Certificate
Certificate Number
TUV
R50135086
UL
E317337
EMC CE
AE 50285865 0001
CB
JPTUV-049251
FCC
FDA
ROHS
WTF14F0514437E
1331340-000
RHS01G006464
Applicable Standard
EN 60950-1:2006+A11+A1+A12
EN 60825-1:2007
EN 60825-2:2004+A1+A2
UL 60950-1
CSA C22.2 No. 60950-1-07
EN 55022:2010
EN 55024:2010
IEC 60825-1
IEC 60950-1
47 CFR PART 15 OCT., 2013
CDRH 1040.10
2011/65/EU
*The above certificate number updated to June 2014, because some certificate will be updated every year, such
as FCC, FDA and ROHS. For the latest certification information, please check with Eoptolink.
Product Description
EOLT-C02-02-X/EOLT-C03-02-X series is a 10/100BASE-T Copper Small Form Pluggable
(SFP), which is based on the SFP Multi Source Agreement (MSA). It’s high performance, cost
effective module compliant with the 100BASE-T standards as specified in IEEE 802.3-2002 and
IEEE 802.3u, which supporting 100Mbps up to 100 meters reach over unshielded twisted-pair
category-5 cable. EOLT-C03-02 can perform any necessary scrambling / descrambling between
the 100Base-TX and 100Base-FX formats and support intelligent auto-negotiation 100BASE-T
operation in host systems.
Absolute Maximum Ratings
Parameter
Symbol
Min
Typ
Max
Maximum Supply Voltage
Vcc
-0.5
4.0
Storage Temperature
TS
-40
85
Normal operating condition
Parameter
Symbol
Operating Case Temperature
Tc
Supply Voltage
Vcc
Min
Typ
Max
0
70
-40
85
3.15
3.3
Eoptolink Technology Inc., Ltd.
Page 2 of 8
3.45
Units
°C
Ref.
Standard
Industrial
V
V1.f
Copper SFP Series
Electrical Characteristics
Parameter Symbol
Supply
Current
Icc
Input
Voltage
Vcc
Surge
Current
Isurge
Min
Typ
Max
Units
+3.3 Volt Electrical Power Interface
3.13
170
300
mA
3.3
3.47
V
30
mA
Notes/Conditions
Low-Speed Signals, Electronic Characteristics
SFP Output
LOW
SFP Output
HIGH
SFP Input
LOW
VOL
VOH
VIL
SFP Input
HIGH
VIH
0
0.5
host_Vcc-0.5
host_Vcc+0.3
0
0.8
2
Vcc + 0.3
V
4.7k to 10k pull-up to
host_Vcc, measured
at host side of
connector
V
4.7k to 10k pull-up to
host_Vcc, measured
at host side of
connector
V
4.7k to 10k pull-up to
Vcc, measured at
SFP side of connector
V
4.7k to 10k pull-up to
Vcc, measured at
SFP side of connector
High-Speed Electrical Interface, Transmission Line-SFP*note1
Line Baud
Rates
fL
125
MHz
MLT-3 encoding per
IEEE802.3u
TX Output
impedance
Zout, TX
100
Ohm
Differential,
AC coupled Internally
RX Input
Impedance
Zin, RX
100
Ohm
Differential,
AC coupled Internally
High-Speed Electrical Interface, Host-SFP*note1
Single
ended data
input swing
Vin
250
1200
mV
Single ended
Single
ended data
output swing
Vout
300
1000
mV
Single ended
Rise/Fall
Time
Tr, Tf
3
nsec
20%-80%
TX Input
Impedance
Zin
50
Ohm
Single ended
Eoptolink Technology Inc., Ltd.
Page 3 of 8
V1.f
Copper SFP Series
RX Output
Impedance
Zout
50
Ohm
Single ended
Note1Note1: For detail information, refer to the recommend circuit.
General specifications
Parameter
Data rate
Symbol
Min
Typ
EOLT-C02-02-X
10
EOLT-C03-02-X
125
Max Units
Distance
Notes/Conditions
Mbps
100
m
Category 5 UTP. BER <10-12
Pin Descriptions
Pin No.
Name
Function
1
VeeT
Transmitter Ground
Plug Seq.
1
Notes
2
TX Fault
Transmitter Fault Indication
3
1
3
TX Disable
Transmitter Disable
3
2
4
MOD-DEF2
Module Definition 2
3
3
5
MOD-DEF1
Module Definition 1
3
3
6
MOD-DEF0
Module Definition 0
3
3
7
Rate Select
Not Connected
3
8
LOS
Los of Signal
3
9
VeeR
Receiver Ground
1
10
VeeR
Receiver Ground
1
11
VeeR
Receiver Ground
1
12
RD-
Inv. Received Data Out
3
5
13
RD+
Received Data Out
3
5
14
VeeR
Receiver Ground
1
15
VccR
Receiver Power
2
6
6
4
16
VccT
Transmitter Power
2
17
VeeT
Transmitter Ground
1
18
TD+
Transmit Data In
3
7
19
TD-
Inv. Transmit Data In
3
7
20
VeeT
Transmitter Ground
1
Notes:
1. TX Fault is not used and tied to ground within the module.
2. TX Disable is not used and is not connected within the module.
3. MOD-DEF 0,1,2 are the module definition pins. They should be pulled up with a 4.7k~10kΩ
resistor on the host board. The pull-up voltage shall be VccT or VccR.
MOD-DEF 0 is tied to ground within the module.
MOD-DEF 1 is the clock line of two wire serial interface for serial ID
MOD-DEF 2 is the data line of two wire serial interface for serial ID
Eoptolink Technology Inc., Ltd.
Page 4 of 8
V1.f
Copper SFP Series
4. LOS is not used for EOLT-CXX-02, EOLT-CXX-02-A. For EOLT-CXX-02-E, the LOS will be
LVTTL low for link ok and will be LVTTL high for link off. Externally pull up to VccR or VccT
with 4.7k – 10k ohm on host board.
5. These are the differential receiver output. Internally AC-coupled in the transceiver. 100Ω
differential lines and 100 Ω terminate resistor should be used on the host board.
6. VccT and VccR are internally connected together in the transceiver.
7. These are the differential receiver input. Internally AC-coupled in the transceiver. 100Ω
differential lines and 100 Ω terminate resistor is used in the transceiver.
The following is the Diagram of host board connector pin numbers and names
Serial Communication Protocol
Eoptolink Copper SFP support the 2-wire serial communication protocol defined in the SFP MSA.
These SFP use a 128 byte EEPROM with an address of A0H. The 10/100/BASE-T physical layer
IC can also be accessed via the 2-wire serial bus at address ACH.
EEPROM Serial ID Memory Contents
Accessing Serial ID Memory uses the 2 wire address 1010000X (A0H). Memory Contents of
Serial ID are shown in Table 1.
Table 1 Serial ID Memory Contents
Addr.
Size
(Bytes)
Name of Field
Hex
Description
BASE ID FIELDS
0
1
Identifier
03
SFP
1
1
Ext. Identifier
04
SFP function is defined by
serial ID only
2
1
Connector
22
RJ-45
3-10
8
Transceiver
00 00 00 20 00 00 00 00
100BASE-FX
11
1
Encoding
02
4B5B
12
1
BR, Nominal
01
100M
Eoptolink Technology Inc., Ltd.
Page 5 of 8
V1.f
Copper SFP Series
13
1
Reserved
00
14
1
Length (9µm)km
00
15
1
Length(9µm)100m
00
16
1
Length (50µm) 10m
00
17
1
Length(62.5µm)10m
00
18
1
Length (Copper)
64
19
1
Reserved
00
20-35
16
Vendor name
XX XX XX XX XX XX XX
XX(note2) 20 20 20 20 20
20 20 20
36
1
Reserved
00
37-39
3
Vendor OUI
XX XX XX(note2)
40-55
16
Vendor PN
56-59
4
Vendor rev
XX XX XX XX(note2)
60-61
2
Wavelength
00
62
1
Reserved
00
63
1
CC_BASE
Check Sum (Variable)
Transceiver transmit
distance
100m
Vendor name (ASCII)
Transceiver part number
Check code for Base ID
Fields
EXTENDED ID FIELDS
64-65
2
Options
00 00
66
1
BR,max
00
67
1
BR,min
00
68-83
16
Vendor SN
XX XX XX XX XX XX XX Serial Number of transceiver
XX 20 20 20 20 20 20 20
(ASCII). For example
(note2)
20
“B000822”.
84-91
8
Date code
XX XX XX XX XX XX XX Manufacture date code. For
XX(note4)
example “080405”.
92-94
3
Reserved
XX(note4)
95
1
CC_EXT
Check Sum (Variable)
Check sum for Extended ID
Field.
VENDOR SPECIFIC ID FIELDS
96-127
32
Vendor Specific
Read only
128-255
128
Reserved
Read only
Depends on customer
information
Note2: The “XX” byte should be filled in according to practical case. For more information, please refer to the
related document of SFP Multi-Source Agreement (MSA).
Eoptolink Technology Inc., Ltd.
Page 6 of 8
V1.f
Copper SFP Series
Recommended Circuit Schematic
Note5: if TX_disable, LOSS and Tx_Fault are used, they should be connected as the recommend circuit.
Mechanical Specifications
Eoptolink’s Copper SFP transceivers are compliant with the dimensions defined by the SFP
Multi-Sourcing Agreement (MSA).
Eoptolink Technology Inc., Ltd.
Page 7 of 8
V1.f
Copper SFP Series
Obtaining Document
You can visit our website:
http://www.eoptolink.com
Or contact Eoptolink Technology Inc., Ltd. Listed at the end of the documentation to get the latest
documents.
Revision History
DCN
Release Date
Kelly.Cao
Released.
Apr 15, 2009
Kelly.Cao
Update Product List,
PN&LOGO.
Oct 15, 2011
Nov 29, 2011
Revision
Initiated
Reviewed
V1.a
Tim.Liang
V1.b
Phlio
Approved
V1.c
Phlio
Kelly.Cao
Update application
information and add
recommend circuit.
Update the output
amplitude.
V1.d
Angela
Kelly,
Torres
Update product picture
and mechanical drawing
June 13, 2013
V1.e
Torres/
Angela
Update Features and
regulatory compliance.
June 20, 2014
V1.f
Angela/
Torres
Correct a mistake.
Jan 04,2015
Notice:
Eoptolink reserves the right to make changes to or discontinue any optical link product or service
identified in this publication, without notice, in order to improve design and/or performance.
Applications that are described herein for any of the optical link products are for illustrative
purposes only. Eoptolink makes no representation or warranty that such applications will be
suitable for the specified use without further testing or modification.
Contact:
Add: Floor 5, Building 2, No. 21 Gaopeng Avenue, High-Tech District, CHENGDU, SICHUAN
610041 P.R. CHINA
Tel: (+86) 028-85122709 ext 816 & 809
Fax: (+86) 028-85121912
Postal: 610041
E-mail:sales@eoptolink.com
http://www.eoptolink.com
Eoptolink Technology Inc., Ltd.
Page 8 of 8
V1.f

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project