Firmware update instruction

Firmware update instruction
Step 1 : Connect To Computer
Step 2 : Open NUX DFU Updater
A) Click on:
A) Unplug power supply from pedal.
USB
NUX DFU Updater
Open Window
B) Hold down pedal footswitch &
Plug in the power receptor.
You Will See
NUX Firmware Updater v1
NUX Firmware Updater v1
(no device found)
(no device found)
B) Connect micro-USB cable from computer
to pedal.
1. Click 'Select file’ button to select an firmware file.
Start Update
1. Click 'Select file’ button to select an firmware file.
Select File...
Start Update
Select File...
v1.1.2
v1.1.2
Step 3 : Select Pedal Bin
Step 4 : Start Updating
NUX Firmware Updater v1
NUX Firmware Updater v1
NUX Firmware Updater v1
YOUR PEDAL NAME
YOUR PEDAL NAME
YOUR PEDAL NAME
Product: Monterey Vibe
Version: MR01M1.1
Product:V1
Version:2.0.0
v1.1
1.Adds new vibrato mode.
Usage: Press and hold foot switch for 2 seconds to switch effects between
chorus and vibrato.
RED LED: Chorus mode
GREEN LED: Vibrato mode
V2.0
1.Support Tape Core Editor
2.Add new reverb effect (need TapeCore Editor)
3.Add Smart Tap Tempo Mode (need TapeCore Editor)
4.Add Sync Mode (need TapeCore Editor)
Start Update
Select File...
Start Update
3.Device found. Click update and continue.
Select File...
v1.1.2
v1.1.2
Light Will Flash
2.Adds smart tao tempo
Usage: tap the foot switch to the beat(quarter-note tempo). the speed of
effect will change to the interval between the last two taps. The two taps
must be less than 1.5 seconds apart(greater than 40 BPM).
2.Let Device into DFU mode and connect To Computer.
Ensure the firmware is match the device.
1. Click 'Select file’ button to select an firmware file.
v1.1.2
v1.1.2
v1.1.2
v1.1.2
Start Update
( During & After
Update Complete )
v1.1.2
Select File...
v1.1.2
A) Click on: Select File
B) Select bin file ( zip )
Start Update
Step 5 : Let File Install
Step 6 : Finishing Update
A) Close the update window
NUX Firmware Updater v1
B) Unplug power & micro-USB from pedal
YOUR PEDAL NAME
Do Not Unplug Pedal !
When Update is
Complete Will Say
NUX Firmware Updater v1
Product: Monterey Vibe
Version: MR01M1.1
v1.1
1.Adds new vibrato mode.
Usage: Press and hold foot switch for 2 seconds to switch effects between
chorus and vibrato.
RED LED: Chorus mode
GREEN LED: Vibrato mode
2.Adds smart tao tempo
Usage: tap the foot switch to the beat(quarter-note tempo). the speed of
effect will change to the interval between the last two taps. The two taps
must be less than 1.5 seconds apart(greater than 40 BPM).
4. Update Finished.
Start Update
v1.1.2
Select File...
v1.1.2
YOUR PEDAL NAME
Product: Monterey Vibe
Version: MR01M1.1
v1.1
1.Adds new vibrato mode.
Usage: Press and hold foot switch for 2 seconds to switch effects between
chorus and vibrato.
RED LED: Chorus mode
GREEN LED: Vibrato mode
2.Adds smart tao tempo
Usage: tap the foot switch to the beat(quarter-note tempo). the speed of
effect will change to the interval between the last two taps. The two taps
must be less than 1.5 seconds apart(greater than 40 BPM).
4. Update Finished.
Start Update
v1.1.2
Select File...
v1.1.2
C) Enjoy the pedal !
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising