PP 1SUB - Arendse Car Systems
UPGRADE
Your Audio System
ENGLISH VERSION
plug & play
1
Table of contents
MUSIC
A new experience
Amplifiers
PP 41DSP.................................................................................. 4
PP 1SUB..................................................................................... 6
PP 52DSP.................................................................................. 8
PP 82DSP.................................................................................. 10
Enclosure subwoofers
PP 7E-D...................................................................................... 14
PP 7S-D...................................................................................... 14
PP 8E-Q...................................................................................... 15
PP 10E-D.................................................................................... 10
Subwoofer chassis:
PP 72W-D.................................................................................. 16
PP 8W-Q.................................................................................... 16
Plug & play
The concept - upgrade your audio system.................. 18
The accessories....................................................................... 19
2
Philosophy
Music is pure emotion and should be
a feast for the senses. Most of the OE
sound systems, however, seem hardly capable of arousing emotions,
much less setting off waves of audiophile enthusiasm. The most beautiful music means nothing without
that spark of excitement! But now
there's an ideal solution for turning
the dream of audio excellence into
reality. With its intelligent plug &
play components, Audiotec Fischer is
trailblazing totally new paths to get
the most in sound excellence out of
original audio systems at a minimum
of installation effort. In doing so, our
overriding credo is: Your car should
stay the way it is. Not one single
cable has to be cut or modified to install our MATCH sound systems. This
is pure enjoyment with no regrets –
combined with a sound experience
in a new dimension. Let yourself be
seduced by us!
Here are the advantages at a glance:
• No need to replace the OE radio or OE speakers
• No changes to the vehicle electrical system
• No intervention in existing CAN/MOST bus systems
• A ll wiring is pre-assembled for genuine "plug & play"
• Short installation times (generally < 1 hour)
• No restrictions in the everyday use of the vehicle
• Easy de-installation without leaving a trace
3
PP 41DSP
Simple, simpler, PP 41DSP - a sound
upgrade of original sound systems
has never been easier. The PP 41DSP
is specified by vehicle manufacturer,
comes already completely configured,
and in most editions is offered with the
matching vehicle-specific connection
cable. The internal memory contains
up to 16 different setups for the digital
signal processor in the amplifier. Simply adjust the number to the right setup for your own vehicle using two buttons, and your original speakers will be
vaulting to new audio peaks in no time.
Perhaps no need to say that the included cable set enables a connection
that require not even a single modification to the vehicle wiring harness.
That is plug & play in its purest form.
PP 41DSP
RMS / max. power:
4
- at 4 ohms
4 x 35 / 70 watts
- at 2 ohms:
4 x 50 / 100 watts
Frequency range:
20 Hz - 22,000 Hz
Number of inputs:
4 x Highlevel
DSP resolution:
56 bits
DSP processing power
50 MIPS
Total harmonic distortion (THD):
< 0.03 %
Signal-to-noise ratio:
> 100 dB
Damping factor:
> 100
Input impedance:
30 ohms
Dimensions (H x W x D):
44 x 185 x 124 mm
compact
Pure and simple
Amplifiers
PP 41DSP is a perfect example of how
easy it can be to embrace state-of-theart technology. Foolproof connections
and only two buttons for the right
configuration in a matter of seconds
– that's all there is to it. What's more,
the compact design enables effortless
installation - you'll be enjoying this audio boost all the more quickly.
It's all here
Up to 16 different sound setups are
already pre-programmed and can be
called up using the two buttons. The
display on the top side indicates the
selected memory slot.
Features PP 41DSP:
Need more bass?
The PP 41DSP is configured to enable
a rich bass sound with your original
speakers. For even more bass, we
recommend the PP 1SUB subwoofer
amplifier. This is connected using only
a single cable and drives any type of
MATCH subwoofer.
- Effortless plug & play connection to the original sound systems
using vehicle-specific adapter cables
-U
p to 16 different DSP setups that are pre-programmed can be
called up at the touch of a button
- Indication of the selected setup via a 7-segment display
- L ow-level sub out for a separate PP 1SUB subwoofer amplifier
- 56 bit DSP technology and 24 bit AD/DA converter
- S tart/stop capability, all the way down to 6V supply voltage
- MCM power supply technology with "ECO mode"
Uncompromisingly stable
The PP 41DSP is totally oblivious to
fluctuations in battery voltage. Its
highly efficient MCM power supply
technology keeps the internal supply
voltage of the output stage 100%
stable – even when starting the engine. This "start/stop capability" is
one of the many unique features of
all MATCH amplifiers.
Finest sound engineering
A digital signal processor with 56 bit
resolution and high-end converters by
the manufacturer Asahi Kasei, a company renowned for its studio equipment, provide for superb sound characteristics.
- Connection for optional cable remote control
- S tate-of-the-art SMD technology for a smaller footprint and
maximum reliability
- P rinted circuit boards in fourfold multilayer technology for optimal power
and signal transmission
5
PP 1SUB
Sometimes, only more is enough – PP
1SUB is an ideal complement to the PP
41DSP, when you like to feel the bass.
This extremely compact subwoofer
amplifier drives our MATCH subwoofers
to acoustic peaks of performance.
The proper setting of key parameters
such as crossover frequency, level and
phase can be really tricky; good thing
you don't have to worry about this
at all. We've already handled it for
you and provided for vehicle-specific
pre-programming in the PP 41DSP
setups. This demonstrates that the PP
1SUB thus not only benefits from the
sophisticated DSP technology of the
PP 41DSP, it also is combined exclusively with it and was not designed
as a stand-alone amplifier.
PP 1SUB
RMS / max. power:
6
- at 2 ohms:
1 x 160 / 320 watts
(4 channels 40 / 80 watts each)
Total harmonic distortion (THD):
< 0.03 %
Signal-to-noise ratio:
> 100 dB
Damping factor:
> 100
Input impedance:
30 ohms
Dimensions (H x W x D):
44 x 185 x 64 mm
MORE
Sounds deep
Amplifiers
For all its robust power of 160 watts,
the PP 1SUB is extraordinarily compact, which means it fits easily anywhere inside the car. Depending upon
space available, it can even be installed
next to the PP 41DSP or near the respective MATCH subwoofer. Because
the connection cables (1 m length and
included in the delivery of the PP 1SUB,
4.8 m length and included in delivery
with the MATCH enclosed subwoofers)
are bidirectional and interchangeable
for effortless installation.
The connection becomes child's play
The PP 1SUB receives all its signals,
including supply voltage, through the
PP 41DSP MATCH amplifier. One single pre-assembled cable (included in
delivery) provides the necessary connection. Even the MATCH subwoofers
are connected to the PP 1SUB with a
single cable (included in the delivery
of the subwoofers).
Always impeccably configured
Nothing could be simpler - the PP
1SUB receives its input signal via the
PP 41DSP. All pre-adjustments for optimal adaptation to the other speakers in the vehicle are already included in each vehicle specific setup. The
subwoofer level can be adapted to
your personal tastes via the included
cable remote control.
The suitable MATCH subwoofer
The PP 1SUB is exclusively designed
to be combined with subwoofers of
the MATCH series (see label on the PP
41DSP packaging). It is not suitable
with subwoofers of other manufacturers. There are the following MATCH
subwoofers to choose from: PP 7E-D,
PP 7S-D, PP 8E-Q and PP 10E-D.
Features of the PP 1SUB:
- The ideal complement to the MATCH PP 41DSP amplifier
- Effortless plug & play connection using a total of just two cables
- Optimally pre-configured through the PP 41DSP sound setup
- Easily combined with the MATCH subwoofers PP 7E-D, PP 7S-D, PP 8E-Q and PP 10E-D
- Cable remote control for the subwoofer levels is included in delivery
7
PP 52DSP
The best of both worlds – the new PP
52DSP strikes a perfect balance between simple installation and maximum versatility. Those who like things
quick and simple can load an appropriate vehicle-specific setup per MicroSD
card into the amplifier and let the fun
begin. Audiophiles who create their
own sound setup will enjoy the integrated USB interface for direct connection to a PC and the sensational options
for trying their hand at sound engineer-
ing. Thanks to the two-channel, freelyconfigurable preamplifier output, there
is even an option of combining the system with additional amplifiers.
Plug & play doesn't get any more versatile than this.
PP 52DSP
RMS / max. power:
8
- at 4 ohms
4 x 35 / 70 watts
- at 2 ohms:
4 x 50 / 100 watts
- Match Subwoofer at 2 ohms:
1 x 160 / 320 watts
Frequency range:
10 Hz - 22,000 Hz
Number of inputs:
4 x Highlevel, 1x Aux
DSP resolution:
56 bits
DSP processing power
172 MIPS
Total harmonic distortion (THD):
< 0.01 %
Signal-to-noise ratio:
> 103 dB
Damping factor:
> 100
Input impedance:
30 ohms
Dimensions (H x W x D):
44 x 185 x 154 mm
UNIVERSAL
Master of all trades
Amplifiers
"The Beauty is a Beast" – through targeted fine-tuning of all electronic devices, the PP 52DSP offers a rich and
balanced sound reproduction, which
is accented especially in combination
with the MATCH subwoofers. Incredible bass power is guaranteed here.
USB on board
Those who want to create their own
sound setup can connect the PP 52DSP
directly to a PC and get started. The
software required to do so is available
free on our website www.audiotecfischer.com
Open for system enhancements
In addition to the five internal amplifier channels, the PP 52DSP offers the
option of establishing a connection
to additional amplifiers through the
2-channel preamplifier output. This
output is totally freely configurable using the DSP PC Tool. Its maximum output voltage of 3V is even completely
galvanically isolated, in order to eliminate any interference noise caused by
ground loops.
Everything under control
The optional cable remote control
also provides a novel feature – both
controllers and the selector switch
are freely assignable using software. You can decide whether you
want to use it for controlling the
overall volume, subwoofer level or Aux
input. Various functions can also be assigned to the switch.
Seven in one fell swoop
The DSP PC-Tool software enables
each of the seven channels to be
freely configured. You have direct access to highpass, lowpass and bandpass filters, along with numerous EQ
bands. Get ready for your perfect
sound experience.
Features PP 52DSP:
- Effortless plug & play connection to the original sound systems
using vehicle-specific adapter cables
- Upload of vehicle-specific setups via a MicroSD memory card
- E xtremely high performance DSP with virtually boundless sound engineering
opportunities; freely configurable using PC software
-5
6 bit DSP technology and 24 bit AD/DA converter from Burr-Brown
- USB interface for direct connection to a PC
- F reely configurable to two-channel pre-out for the connection
of additional amplifiers
- Aux input with automatic or manual changeover
- Start/stop capability, all the way down to 6V supply voltage
- MCM power supply technology with "ECO mode"
-C
onnection for optional cable remote control,
functionality configurable using PC software
- S tate-of-the-art SMD technology for a smaller footprint and
maximum reliability
- P rinted circuit boards in fourfold multilayer technology for optimal power
and signal transmission
9
PP 82DSP
The crowning achievement of this
plug & play amplifier series – the new
PP 82DSP, with its incredible performance on a small footprint – outshines all the previous models that
came before it. With its enormous
range of functions, thanks to Audiotec
Fischer's unique Class HD technology,
it is setting a whole new standard in
terms of efficiency. The combination
of state-of-the-art digital amplifier
technology and a dynamically-controlled switched-mode power supply
reduces heat generation and power
consumption to an absolute minimum. But that's not all – no less than
eight separate and freely-configurable amplifier channels with incredible power enable even sophisticated system configurations with one
single amplifier.
PP 82DSP
RMS / max. power:
10
- at 4 ohms
8 x 55 / 110 watts
- at 2 ohms:
8 x 70 / 140 watts
Frequency range:
10 Hz - 22,000 Hz
Number of inputs:
4 x Highlevel, 1x Aux, 1x optical
DSP resolution:
56 bits
DSP processing power
172 MIPS
Total harmonic distortion (THD):
< 0.02 %
Signal-to-noise ratio:
> 100 dB
Damping factor:
> 100
Input impedance:
30 ohms
Dimensions (H x W x D):
44 x 185 x 164 mm
performance
The powerhouse
Amplifiers
Fireworks of cutting-edge technologies for sound enjoyment at the highest level – never before has so much
ingenuity been put into offering half a
kilowatt of power on such a small footprint. With all the focus on the technical features, it's easy to forget that the
PP 82DSP with its phenomenal design
is also enticing to look at and to touch.
The secret of maximum efficiency
The totally new P³S power pack of the
PP 82DSP controls the internal supply
voltage of the Class-D output stages,
depending upon the audio signals of
all eight channels. This combination
guarantees unparalleled overall efficiency and minimal heat generation.
An Interface in any case
Whether it be the Aux input for an
iPod/iPhone, optical input for digital
sources with virtually any scanning
sampling rate from 6 – 192 kHz or a
preamplifier output for the connection of additional output stages – PP
82DSP leaves nothing to be desired.
Functionality on request
The optional cable remote control is
just as flexible as the PP 82DSP – both
controllers and the selector switch are
freely assignable using via our PC tool
software. You can decide whether you
want to use it for controlling the overall
volume, subwoofer level or the Aux input, for example. Various functions can
also be assigned to the switch.
“Eight” in one fell swoop
This is truly remarkable for an amplifier in this performance class – all eight
channels of the PP 82DSP are configurable with DSP functions via the PC
software. Four of these channels can
even be mixed through a signal matrix
consisting of arbitrary input signals.
Features PP 82DSP:
- Proprietary Class HD technology for unparalleled efficiency and minimal
heat generation
- Eight independently configurable amplifier channels for maximum flexibility
- E xtremely high performance DSP with virtually boundless sound
engineering opportunities; freely configurable using PC software
- 56 bit DSP technology and 24 bit AD/DA converter from Burr-Brown
-O
ptical S/PDIF input 6 – 192 kHz with integrated
sampling converter
- USB-on-board for direct connection to a PC
- F reely configurable to two-channel pre-out for the connection of additional
amplifiers
- Aux input with automatic or manual changeover
- Start/stop capability, all the way down to 6V supply voltage
-T
he latest D/A converter-controlled P³S power supply technology with
"ECO Mode"
-C
onnection for optional cable remote control, functionality
configurable using PC software
- S tate-of-the-art SMD technology for a smaller footprint and
maximum reliability
- P rinted circuit boards in sixfold multilayer technology for optimal
power and signal transmission
11
The right bass for every purpose – the
brand-new subwoofers are the ideal
complement to the MATCH amplifiers. Choose your dream combination
based on available space in your trunk
and your personal demand not only
to hear the music but to feel it. These
subs are the best example of how an
intelligent teamwork of amplifier and
speakers, thanks to sophisticated DSP
technology, can create intense bass
you can feel inside the vehicle, even
12
12
with extremely small dimensions. The
secret lies in the meticulous matching of components – only in concert
with the MATCH amplifiers can these
subwoofers ascend to the heights of
audio brilliance.
Feel the Power
The space savers
Enclosure subwoofers
A MATCH made in heaven
All MATCH enclosure subwoofers are designed as so-called "highpass filtered vented systems". This
means that a suitable highpass filter in DSP must be configured, so that these subwoofers can
deliver the right performance. In the latest PC-Tool software, the appropriate settings are already
saved and can be retrieved at the "push of a button".
The simple connection
A pre-assembled connection cable (4.8
m long) is included with all MATCH
enclosure subwoofers. Thanks to the
coded plug connectors, it is impossible
to hook up the wrong connection by
accident. This means that the connection to the MATCH amplifiers is a snap.
A great bass without loss of space
The PP 7S-D fits inside the spare wheel
compartment on most vehicles in
place of the spare wheel. This means
that not one liter of precious trunk capacity is lost. The woofer is attached
to the central bolt which normally
holds the spare wheel into place. This
means you can derive maximum bass
enjoyment with a minimum space requirement.
Features of enclosure subwoofers:
- Optimized for MATCH plug & play amplifiers
- Extremely easy connection of pre-assembled subwoofer wiring assemblies
(in the delivery)
- Incredibly stiff, scooped paper membranes
- High-endurance voice coils with large layer widths
-Double-vented voice coils for minimized compression effects
- Sturdy metal grille offers optimal protection for your woofers
13
13
PP 7E-D
PP 7S-D
Compact bass-reflex subwoofer, equipped with two 165
mm woofers with dual voice coil, impedance 4 x 2 ohms
Round bass-reflex subwoofer, equipped with two 165
mm woofers with dual voice coil, impedance 4 x 2 ohms,
fits into many spare wheel recesses instead of the spare
wheel.
PP 7E-D
14
PP 7S-D
RMS / max. power:
200 / 400 watts
RMS / max. power:
200 / 400 watts
Sensitivity
90 dB 1W / 1m
Sensitivity
90 dB 1W / 1m
Impedance
4 x 2 ohms
Impedance
4 x 2 ohms
Linear cone excursion:
+/- 5 mm
Linear cone excursion:
+/- 5 mm
Dimensions (H x W x D):
280 x 318 x 310 mm
Dimensions (H x W x D):
500 x 120 mm
Enclosure subwoofers
PP 8E-Q
PP 10E-D
Extremely compact "downfiring" bass reflex subwoofer
with only 9 liters of net volume, 200 mm woofer with
fourfold (quad coil) voice coil, impedance 4 x 3 ohms
Particularly high-performance bass reflex subwoofer
with two 250 mm woofers with dual voice coil and impedance of 4 x 2 ohms
PP 8E-Q
PP 10E-D
RMS / max. power:
200 / 400 watts
RMS / max. power:
300 / 600 watts
Sensitivity
87 dB 1W / 1m
Sensitivity
91 dB 1W / 1m
Impedance
4 x 3 ohms
Impedance
4 x 2 ohms
Linear cone excursion:
+/- 6.5 mm
Linear cone excursion:
+/- 5.5 mm
Dimensions (H x W x D):
189 x 340 x 310 mm
Dimensions (H x W x D):
375 x 400 x 415 mm
15
self-made
PP 72W-D
Bass Power
You didn't find the right type of
product? In case none of the four
MATCH enclosure subwoofers fit the
optimal styling in your vehicle, then
the PP72 W-D and PP8 W-Q woofers
offer the opportunity for customizing your own subwoofer. These
single chassis are exactly identical
to the systems fitted in the various
enclosure models. As long as your
customized cabinet conforms to our
specifications with respect to the
16
16
net volume and the matching of the
bass reflex channel, identical sound
performance is guaranteed.
PP 72W-D (per subwoofer)
Qes:
0.41
RMS / max. power:
100 / 200 watts
Qts:
0.37
Sensitivity
87 dB 1W / 1m
VAS:
7.9 liters
Impedance
2 x 2 ohms
Linear cone excursion:
+/- 5 mm
Resonance frequency:
53 Hz
Installation depth:
80 mm
Qes:
3.3
Installation diameter:
134 mm
1 pair of 165 mm subwoofers
with 2x2 ohms dual voice coil for
compact bass reflex enclosures
(approx. 15 liters of net volume),
connection terminal included in
delivery
Subwoofer Chassis:
PP 8W-Q
200 mm subwoofer with 4x3 ohms
quad voice coil for extremely compact
bass reflex housings (approx. 9 liters
of net volume), connection terminal
included in delivery
PP 8W-Q
Qes:
0.57
RMS / max. power:
200 / 200 watts
Qts:
0.51
Sensitivity
87 dB 1W / 1m
VAS:
23 liters
Impedance
4 x 3 ohms
Linear cone excursion:
+/- 6.5 mm
Resonance frequency:
37 Hz
Installation depth:
105 mm
Qes:
5.4
Installation diameter:
183 mm
Peak of Professionalism
In order to make your life as easy as
possible when designing your own enclosure, the MATCH single subwoofers
already contain the appropriate connection terminal with pre-assembled
plug connectors. This means you won't
even need a soldering iron to connect
it to the woofer.
You decide the length
Those building their own enclosure
also require an adequate connection
cable to the MATCH amplifier. These
are available individually – allowing
you to choose from among three different lengths (1 m, 3.3 m or 4.8 m).
Features of subwoofer chassis:
- Incredibly stiff, scooped paper membranes
- High-endurance voice coils with large layer widths
- Double-vented voice coils for minimized compression effects
- Powerful magnet drives for compact bass reflex enclosure
- Connection terminal for MATCH subwoofer cables included in delivery
17
17
PLUG & PLAY – Upgrade Your Audio System!
Why replace equipment when you
can complement them - a mere two
additional components provide for a
dramatic improvement in sound reproduction and a significant increase in
the dynamics themselves in connection
with the original radio and the standard speaker installation. The following
graphic illustrates the simple plug &
play concept for which not one single
cable needs to be cut in your vehicle.
Everything is pre-assembled and can be
plugged together in ways protecting it
against polarity reversal.
Particularly important for leasing vehicles - all components can be removed
again without leaving a trace!
Original
head unit
Original
connector
of the
head unit
MATCH
amplifier
Vehicle-specific
MATCH
cable
MATCH
subwoofer cabel
MATCH
subwoofer
18
ingenious
Simple
More is less
For anyone worried that the original
speakers won't withstand the additional power of the MATCH amplifiers,
we can allay their concerns. Because
although double the power is available
per channel compared to the original
car radio, the speakers are in fact subjected to far less mechanical stress.
Why? Because the subwoofer does all
the "heavy labour" and takes care of
the reproduction of the low frequencies. The remaining speakers are relieved of the very low frequencies due
to matched, high-slope highpass filters.
Less cone excursion means a lower load
on the speaker and less risk of exciting
resonance in the installation location of
the speakers. Finally, dedicated limiters
ensure that the amplifiers will not be
overdriven, which in turn protects your
speakers.
Accessories
We dazzle – You marvel!
It really is fascinating how much sound potential you can coax out of OE-speakers.
But just getting an additional power is only half the story. Because these days an
amplifier has to offer much more. The intelligence is revealed in the digital processors in our MATCH amplifiers, whose incredible processing power can compensate
for virtually all the inadequacies of the original speakers as well as the individual
vehicle acoustics. Per channel there are up to 30 equalizer bands available. Add
to this variable highpass and lowpass filters, along with a for the driver’s seat optimized time-alignment ensure to experience the music precisely from the front and
not diffused “from the side”.
The figure shows three curves:
red = reference curve
green = measurement of a standard sound system
blue = measurement after the MATCH installation and DSP correction
URC 2A
The matching cable remote control
for the PP 52DSP and PP 82DSP
amplifiers offers not only the option
of adjusting the level of the subwoofer or an additional incoming
AUX source conveniently from the
driver's seat but also shutting off
the vehicle-specific sound tuning.
This allows you to present the "aha"
effect of sound optimization in a
particularly spectacular way. Those
creating their own sound setup using our DSP PC-Tool software can
even configure the function of the
controllers and switches on the URC
2A according to their own taste.
Vehicle-specific adapters
40 different adapters for some
2,500 different vehicles are available and enable connection of the
MATCH amplifiers to the original
cable harness of the vehicle without having to cut through a single
wire. These adapters are combined
with ISO connection cables that
come along with the PP 52DSP and
PP 82DSP amplifiers. By contrast,
on the vehicle-specific PP 41DSP
variant, an adapter is no longer required, as everything is included in
the delivery.
Cable lengths for all needs
The cables that come with our
amplifiers and subwoofers are optimized in terms of their length for
the typical installation positions.
For other installation places, however, it may be useful or necessary
to use longer or even shorter variants. Here Audiotec Fischer also
provides the right product for virtually every product use. Regardless of whether it involves the ISO
amplifier connection cable or the
feed line to the subwoofer – other
lengths are optionally available.
19
AUDIOTEC FISCHER GmbH
Hünegräben 26, 57392 Schmallenberg
Phone: +49 2972 9788 0
Fax: +49 2972 9788 88
E-mail: match@audiotec-fischer.com
Internet: www.audiotec-fischer.com
20
Distribution: AUDIO DESIGN GmbH
Am Breilingsweg 3, 76709 Kronau
Phone: +49 7253 9465 0
Fax: +49 7253 9465 10
E-mail: info@audiodesign.de
Internet: www.audiodesign.de
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising