Desigo CC
Data Sheet
s
Fire Safety Products
Desigo® CC
Fire Safety Management Station (v2.1)
ARCHITECT AND ENGINEER SPECIFICATIONS
• Industry-leading, pane-based management station
that provides critical data in a single view




Constant display of all active events
Highest-priority events are highlighted
User interface can be configured to support basic-to-advanced needs
User profiles can be created, based on various end-user needs
• Built on a robust Siemens platform that is used worldwide
in critical installations
• Full integration of fire panels, building-automation
systems, video surveillance and access control

One (1) platform to learn and maintain
• UL Listed to 864 9th Edition Standard
• Smart system that anticipates needed data and
for Control Units & Accessories
(for `Command & Control’)
provides the information automatically

Enables faster, more accurate response to critical events
• ULC Listed to ULC-S527 Standard for Control Units and
• Integrates multiple networks for FireFinder®; MXL®
Fire Alarm systems 2nd & 3rd Edition (for `Command
and Control’) and ULC-S559 for Equipment for Fire
Signal Receiving Centre and Systems - 3rd Edition
and Desigo® fire-alarm control panels (FACPs)
• Monitors and controls up to 63 XLS / MXL FACPs; 32
Desigo Fire Safety FACPs per network; Apogee
Building Automation panels and up to 40,000
addressable detection devices

•
UL and ULC recognized as an ancillary annunciator
when used with a non-UL864 / ULC-S527-11 Listed PC
that is connected to a Desigo Fire Safety, FireFinder
XLS or MXL FACP:
Supports CO detection with ASAtechnologyTM
• Automatic or manual Remote Notification (ReNo) of
events via email, text message, or page
• Supports leading open standards: BACnet,
OPC, Modbus, ONVIF and SNMP
• Agency listed for remote access (monitoring only)
via a Virtual Private Network (VPN) connection
System Overview
Desigo CC (v2.1) workstations from Siemens – Fire
Safety provide an integrated, practical approach to
managing and controlling facilities from a flexible,
easy-to-use interface. Desigo CC also provides
facility-wide efficiencies, cost-effective information
sharing, faster event management, and better
decision-making.
Desigo CC software operates on UL Listed hardware
that has passed rigorous performance and
environmental tests. Desigo CC, which is ideally
suited for monitoring and controlling FireFinder XLS
and MXL FACPs, also serves as the management
station for Desigo 252 / 504-point addressable FACPs.



Model MOSA used for connection with XLS and/or MXL FACPs
Model SCALANCE X204-2 switch used for
connection with Desigo Fire Safety FACPs
provides a cost-effective monitoring-only solution for
sites that do not require full control of the fire system
• CSFM [#7300-0067:0267] for Fire
Alarm Control Unit Accessories
Key Features
Server / Client Design
Desigo CC has a flexible, full-system design that
integrates and enables customized workflow
configurations. Desigo CC can be installed on a single
PC, providing complete client / server system
compatibility. The server hosts all system data. Full
control of Desigo CC can be transferred from the server
to a client. A front-end processor (FEP) communicates
data from FireFinder’s XNET, as well as from the
FCnet module on Desigo 252 / 504-point addressable
FACPs, respectively.
In the event of system failure, Desigo CC has the
option to transfer control to a redundant server.
Desigo CC Management Station
s I ndustry, Inc.
Building Technologies Division
5082
Key Features ─ (continued)
Related-Items Pane − Items such as operating procedures
User Interface
and other data that has been linked to specific devices
are listed in this pane. When a device is selected –
either by the operator or by the Desigo CC
management station (based upon an active event) –
all of the information that has been linked to that
device is displayed in the Related-Items Pane.
Desigo CC’s User Interface displays all critical data in a
single view. This provides faster, more accurate response
to events, and makes Desigo CC easy to use and easy to
learn. Key components of the UI are as follows:
Summary Bar
The Summary Bar serves as an important source of
data for Desigo CC event management, and highlights
current system status with clear indication of currentevent priorities. Event lamps for Alarm, Trouble, and
Supervisory events are highlighted with different
colors when events occur. The top two (2) priority
events in the system that are currently active are
displayed in the Summary Bar. The Summary Bar is
visible at all times.
Text Pane − The Text Pane provides a summary of the
current value and status of any selected object without
any prior system configuration. This is a convenient
feature for obtaining an overview of system and / or
device status.
Investigative Treatment for Event Management −
Desigo CC enables fast response to system events
through Investigative Treatment. When an event occurs,
Desigo CC will find the device that is the event source in
System Manager, and will bring up information
associated with that device, including graphics and
specific information about the device.
Event Bar
The Event-Bar feature of Desigo CC’s User Interface
displays a lamp for all active events currently in the
system, and is visible on the User Interface at all times.
Operating and Engineering Modes
Desigo CC Manager provides two (2) separate modes for
system use: Operation and Engineering. In Operating
Mode, the end-user has the ability to monitor and
control the system; address events, and analyze current
and past data. Configuration changes, on the other
hand, are possible via Engineering Mode.
Pane-Based Workflow
The User Interface has well-defined, pane-based
workflow that keeps essential data in front of each enduser with no overlapping windows. End users can
navigate the system through Systems Manager or via
graphical interface. Panes can be tailored to the userspecified requirements for a specific building or facility.
Additionally, every user who is granted access privileges for
system configuration can toggle Desigo CC into
Engineering Mode, where system parameters can be set
and user accounts can be managed. This is a powerful
feature that should be limited to only a few advanced users.
Pane-based workflow provides the following features:
System Manager − used for navigating Desigo CC to
view and control current conditions, analyze
historical operation, and to configure Desigo
CC. The System Manager uses a common,
consistent workflow for all system navigation.
System Manager allows the end user to either
select from traditional applications in
‘Applications View,’ or permits user-specified
navigation in ‘Management View’, guiding the
end-user to the most relevant data
(e.g. – selecting a certain part of the
building for further detail, analysis).
Event List
The Event List provides a complete, easy-to-filter list of all
active events in the system. Event List gives clear indication
of each event’s source and current status.
Custom messages and suggested action steps are displayed
to the end-user, via the use of text, color, and icon
representations. Events can be ‘acknowledged’, ‘silenced’,
and ‘reset,’ via Event List.
Primary Pane − the primary pane is used to show data that is
Graphics
Desigo CC graphics are built using smart objects that know
how they are used and how to represent themselves
graphically. The use of smart objects allows you to create
graphics by simply dragging and dropping objects onto a
page, without manually binding object to graphical symbols.
Desigo CC also provides a powerful AutoCAD importing tool
that allows you to select and manipulate layers of AutoCAD
drawings during and after the import process. The following
file types are supported: .DWG, .DXF, .PNG, .BMP, .GIF,
.JPG, .JPEG, .TIF, .TIFF, .RLE, .ICO.
critical to event response. This includes device
information, key facility graphics (e.g. ─ campus
layout), and floor-layout plans that show the location
of selected devices or those that are in Alarm mode.
Secondary Pane − the secondary pane is used
to display additional, critical data, including:

A Reaction Processor that can be used for defining
simple, time-based activities that include:
– scheduling backups, trend collections and reports
s I ndustry, Inc.
Building Technologies Division
–2–
Key Features ─ (continued)
Remote Access
Desigo CC’s User Interface can be accessed from remote,
non-UL PCs solely for monitoring, via the available Web
Client. This Remote Access feature enables up to 20 key
stakeholders to have the same view of the User
Interface as those operating the system from a remote
PC ─ provided Desigo CC is installed on an intranet site –
therefore enabling faster sharing of critical data over a
wide area.
Remote Notification (ReNo)
With the optional Remote Notification enabled, Desigo
CC can be configured to automatically or manually
send email, SMS messages, or pages to first-level
responders. Additionally, escalated notification ─
when necessary ─ can also be sent to second-tier
responders.
Mobile App
The Desigo CC Mobile App is designed for the Android
and iOS operating systems enabling the user to
remotely view events and object status based on user
privileges. Users receive event notifications when new
events are available.
Assisted Treatment
The Assisted Treatment option provides the ability to
pre-define a sequence of steps or actions, allowing the
operator to optionally implement when responding to a
system event. Each Assisted Treatment step provides
instructions and operating tools (e.g. – view the graphic of
The mobile app can optionally provide commanding of
events and objects based on user privileges. The
commanding capabilities of the Mobile App are not
Agency listed or approved for commanding fire
systems. The use of event commanding must be
reviewed with and permitted by the local authority
having jurisdiction (AHJ) or equivalent.
the object in `alarm’; view a related live video stream; fill-in a
treatment form, or automatically print out system-event
information).
End-User Profiles
To ensure proper level of event-management support by
Desigo CC for any system-event situation, pre-defined
profiles can be established for each end-user or
workstation that provide the correct level of event
management for that user or workstation.
Video
The video-surveillance integration supports the workflows
of System Manager and Event Treatment and enhances
these workflows with video specific workflows and video
support that are fully integrated into the Desigo CC UI
experience.
Reports
The Desigo CC reporting tool includes standard
reporting templates. The Reports feature also allows the
development of fully configurable reports with custom
logos, headers, footers and layouts that include tabular
and graphical system data. Reports can be scheduled
and saved in .CSV or .PDF file extensions for future use.
Live streams and recordings can be displayed in the
primary and secondary pane. In the contextual pane video
operations (e.g. – Pan-Tilt-Zoom | Start / Stop recording) can
be executed from both the video control and operations
tabs.
Schedules
Schedules are automatically associated to systems they
operate, in order for the end-user to quickly navigate to
schedules related to any selected object.
Other Desigo CC applications are able to execute video
commands and actions on events of video device
supervision. The video integration is based on Siveillance
VMS or Milestone XProtect Expert / Corporate.
Macros
Macros are pre-defined lists of commands that enable a
user to send out a group of commands to specified
devices with a single action. Macros can be started
manually or automatically based on schedules defined
for time-based functions or automatic reactions.
Access Control
The Access Control option integrates with Siemens SiPass
integrated and adds access control event monitoring and
control capabilities to Desigo CC. Events from Access
Control devices, doors, and areas are seamlessly
incorporated into the Desigo CC event treatment
workflows. Users can view door and I/O status
information in graphics and the operations tab and
monitor device connection status with integrated device
supervision.
Reaction Processor
The Reaction Processor option allows Desigo CC to
automatically execute given actions when some
conditions are verified. Conditions can be any of the
following: time-based (e.g. – every Monday at 7:00 a.m.);
event-based (e.g. – when technical equipment is in fault); a
change of values (e.g. – when the temperature of a room is
higher than a predefined value), or on a variation of any or
all of the above. When conditions are met, the Reaction
Processor executes a pre-configured list of commands
(e.g. – switch on the lights).
All access control commands are available to other Desigo
CC applications (e.g. – Reactions, Macros, & Scheduler)
providing enhanced cross discipline workflows (e.g. – a
card swipe starts recording of nearby camera, activates
lighting, and resets temperatures).
s I ndustry, Inc.
Building Technologies Division
–3–
Key Features ─ (continued)
Specifications ─ (continued)
Multiple Installed Clients
Desigo CC can support up to seven (7) installed clients.
Additionally, control of the fire-safety system can be
transferred to these clients ─ provided the clients’
accounts have been configured to assume control.
Operating Systems
Desigo CC Server, FEP, and Installed Clients run on the
following Microsoft operating systems and editions:
Log Viewer
The Log Viewer application provides a log/history of
system events and user activities. Additionally, the
feature allows users to retrieve past events and
activities for further analysis and investigation. The
Detailed Log within the Contextual Pane provides a log
of the most recent user and system events and
activities, relative to an individually selected object. For
example, the system logs user intervention to a set
point with previous, new value, timestamp and
username. Data displayed within the Detailed Log can
be further analyzed, via sorting and filtering
functionality – similar to that of the Log Viewer.




Web Clients and Windows App Clients run on the
following Microsoft operating systems and editions:






Specifications
Microsoft Windows Server, 2008 R2
(Express and Standard)
Microsoft Windows Server, 2012 R2
(Express and Standard)
Microsoft Windows Server, 2014 R2
(Express and Standard)
Microsoft Office
The following versions and editions of
Microsoft Office are supported:
Desigo CC is a full, flexible client / server architecture for
building automation and fire safety applications, allowing
configurations from small, single-seat to large, multi-user
installations.

Desigo CC can be installed completely on one (1)
computer, with full server and client functionality.
Additional clients (e.g. – dedicated, browser, and Windows
desktop application) can be also be added. Additional
system connections can be made through systems
installed with a Desigo CC’s Front End Process (FEP)
configuration.


Microsoft Office 2013
(Standard, Small Business, Professional, Enterprise)
Microsoft Office 2010
(Standard, Small Business, Professional, Enterprise)
Microsoft Office 2007
(Standard, Small Business, Professional, Enterprise)
Virus Scanners
Desigo CC Server, FEP, and Installed Clients are
compatible with the following Virus Scanners:
A Microsoft IIS server for Browser Clients and Desktop
Application downloads can be installed on the server
or on a separate installation.





The Desigo CC Server, FEP, and Dedicated clients run on
Windows 7, 64-bit, or Windows Server 2008 R2 operating
systems. Browser and Windows desktop application
clients run on Windows 7 or Windows 8.1 operating
systems.
Kaspersky
Avira
McAfee
Bitdefender
TrendMicro
Office Scan
(© 1997-2015 Kaspersky Lab)
(© 2015 Avira Operations GmbH & Co. KG.)
(© 2003-2015 McAfee, Inc.)
(© 1997-2015 Bitdefender)
(© 1998-2013 TrendMicro Inc.)
Firewalls
Desigo CC Server, FEP, and Installed Clients are compatible
with the following Firewalls:
 Norton Security (©1995-2015 Symantec Corporation)
 Comodo Firewall (© 2015. Comodo Group, Inc.)
 Kaspersky TOTAL Security (© 1997-2015 Kaspersky Lab)
 Bitdefender Total Security (© 1997-2015 Bitdefender)

McAfee
(© 2014 McAfee, Inc.)

ZoneAlarm
(ZoneAlarm 2015 Extreme Security)
 Dell SonicWALL security
(© 2015 SonicWALL L.L.C.)

Check Point Next Generation Firewalls
(©2015 Check Point Software Technologies Ltd.)
 Cisco PIX Firewall Software
The server hosts all the data for the system, while the
clients are only for the visualization and the user
interaction. The clients provide a high-resolution interface
to all the relevant server data needed for monitoring and
commanding the system. Control of the fire-safety system
can be transferred from one client to another client if
desired.
s I ndustry, Inc.
Microsoft Windows 7 64-bit
(Professional, Ultimate, and Enterprise)
Microsoft Windows 8.1 64-bit
(Professional, Ultimate, and Enterprise)
Microsoft Internet Explorer 11
Microsoft SQL Server Database
Microsoft SQL Server 2008 R2 Express is free and
included on the product DVD. Additional supported SQL
Server version and editions are:
Document Viewer
The Document Viewer displays object-related data sheets,
operating manuals or other information contained in
document file (e.g. –a data sheet for a detector
or sensor or web page.)
Building Technologies Division
Microsoft Windows 7 64-bit
(Professional, Ultimate, and Enterprise)
Microsoft Windows 8.1 64-bit
(Professional, Ultimate, and Enterprise)
Microsoft Windows Server, 2008 R2
Microsoft Windows Server, 2012 R2
–4–
Specifications ─ (continued)
System Compatibilities
Desigo CC provides full control and monitoring of multiple building systems
for up to ~40,000 addressable fire points^:
 FireFinder XLS and MXL



Desigo Fire Safety





Up to 128 cameras for UL / ULC applications
Up to 512 cameras for non-UL/ULC applications
Up to 16 independent video streams per client
Milestone XProtect Expert / Corporate




Up to four (4) FCnet or FVnet networks
Up to 16 panels per SafeDLINK or 32 panels per FCnet
APOGEE building automation controllers
Simatic S7 PLCs
Siveillance VMS 100, 200, 300




Up to five (5) XNET networks (four [4] via Front End Processors {FEP})
Up to 63 panels per XNET network
Up to 128 cameras for UL / ULC applications
Up to 512 cameras for non-UL/ULC applications
Up to 16 independent video streams per client
SiPass integrated


Connect up to five (5) SiPass integrated servers
Up to 256 doors per server
to the Desigo CC System Dimensioning Guide to verify the mix of fire,
building automation, video and access control point count is supported.
^ Refer
Sub-System and Device Compatibilities
 APOGEE BACnet (PXC series controllers with Firmware 3.2.4, 3.2.5, 3.3, and 3.4 with some exceptions*)
 APOGEE P2 Ethernet (Firmware 2.8.10 in PXC, MBC, and MEC controllers)
 APOGEE P2 RS-485 via AEM (Firmware 2.8 in PXC, MBC, and MEC controllers)
 FireFinder XLS, via XNET (FireFinder XLS v8, v10.4, and v11)
 FireFinder and MXL, via XNET (35.06J)
 Desigo Fire Safety, via FCnet (MP1. x, MP2.0, MP2.1)
 Desigo Fire Safety Intelligent Voice Communication System, via FVnet (MP2.0, MP2.1)
 BACnet IP server devices (BTL listed as B-BC typical)
 OPC Client software solutions (i.e. SCADA solutions) compliant with OPC DA2.0
 OPC Server devices and software solutions (i.e. PLCs) compliant with OPC DA v2.05 / v3.00
 Modbus TCP server devices
 SNMP Manager for monitoring SNMP Agents (v1 and v2)
 Simatic S7- 300/400(-H) / 1200 v3
 SiPass integrated 2.65 SP2 & SP4
 Siveillance VMS 100, 200, and 300 2014 (v7.0c, v7.0d) and 2016 (10.1a)
 Milestone XProtect Expert/Corporate 2014 (v7.0c, v7.0d) and XProtect Expert/Corporate 2016 R2
* Recommended APOGEE BACnet controller compatibility for complete Point, PPCL, and TEC editing capabilities:

PXC with Firmware Revision 3.2.4 or later
 At least one (1) PXC-36 or PXC-M with controller UI files installed
s I ndustry, Inc.
Building Technologies Division
–5–
Technical Data
UL / ULC Listed Workstation
– Hardware Category A or B –
Operating System
Processor
Microsoft Windows 7 Ultimate, 64-bit
Serial / Parallel Ports
Intel i7 4th Generation, 2.4 GHz,
XNET Interface Card
Quad core, QM87 chipset
Memory
32 GB
Disk Drives
(1x) 240GB SSD, SATA III
and (1x) 2TB Hard drive, SATA III
Network Card
Intel GigaLAN with two (2) ports
Graphics Card
PCI Express 2.0 –x–16 Video Card,
2GB of RAM, VGA port and 2 DVI
outputs (1920 –x– 1080)
-andAMD FirePro W5000, 2GB of RAM,
Display Outputs: Two DisplayPort
and one (1) dual-link DVI-I
(Max DisplayPort 1.2 Resolution:
4096 –x– 2160; Max DisplayPort
1.1 Resolution: 2560 –x– 1600;
Max DVI Resolution: 2560x1600)
DVD drive
USB
Serial / Parallel Ports
XNET Interface Card
Monitoring Card
Keyboard / Mouse
Monitoring Card
Keyboard / Mouse
Certifications
PS/2 keyboard and mouse ports
650 Watt
UL864 9th Edition / ULC-S527- 11 /
UL2572 Recognized
UL / ULC Listed 22’’ (56 cm.) Widescreen Monitor
DVD / RW drive
Resolution
1920 –x– 1080 HD
Backlight
LED
Speaker
Two (2) Multimedia Audio Plug
(Built-In, 2W, 3.5mm)
Inputs
VGA DVI-Connector
(D-Sub, 15 pin)
VESA Mount
75 / 75 mm
Dimensions
with Stand
20.2" [W] –x– 15" [H] –x– 6.75" [D]
(51.4 cm –x– 38.7 cm –x– 17.1 cm)
Weight
14.3 Lbs. (6.5 kg.)
Color
black
Siemens Model NCC-2F card
Power Supply Input
120 VAC to 12V DC power brick
Fan Monitoring and Watchdog Card
Power Consumption
41W, typical (max.)
PS/2 keyboard and mouse ports
Current Rating
5A (with audio)
650 Watt
Certifications
UL864 9th Edition / ULC-S527- 11 /
UL2572 Recognized
UL864 9th Edition / ULC-S527- 11 /
UL2572 Recognized
UL / ULC Listed 42’’ (107 cm.) Monitor
Processor (FEP), or Client
UL / ULC Listed Server
– Hardware Category C –
Processor
Siemens Model NCC-2F card
Fan Monitoring and Watchdog Card
Recommended Use: Small / Medium Server
Recommended Use: Small / Medium Server, Front End
Operating System
None
Power Supply
Two (2) USB 3.0 and five (5) USB 2.0
(Note: Two (2) USB 2.0 ports are
behind the door)
One (1) parallel port;
Two (2) RS-232 communication ports
Power Supply
Certifications
– Hardware Category C – (continued)
Resolution
1920 –x– 1080 HD
Backlight
LED
Speaker
Microsoft Windows Server 2012, 64-bit
with 5 Client Access Licenses (CAL)
Two Intel Xeon Processor X5550;
2..4 GHz, Quad Core
None
(Optional add-on available.)
Inputs
VGA DVI-Connector
(D-Sub, 15 pin)
VESA Mount
No
Dimensions
with Stand
41.4" [W] –x– 25.4" [H] –x– 4.4" [D]
(105.1 cm –x– 64.5 cm –x– 11.2 cm)
Weight
70 Lbs. (31.75 kg.)
Color
black
Memory
32 GB
Disk Drives
(1x) 240GB SSD, SATA II
and (1x) 2TB Hard drive, SATA II
Network Card
Intel GigaLAN with two (2) ports
Power Supply Input
90 VAC to 264 VAC
Graphics Card
Dual PCI Express 2.0 –x–16 Video
Card; 2GB of RAM, VGA port and 2
DVI outputs (1920 –x– 1080)
Power Consumption
235W, typical (max.)
DVD drive
DVD / RW drive
USB
Six (6) USB 2.0
(Note: Two (2) USB 2.0 ports
are behind the door)
s I ndustry, Inc.
Building Technologies Division
1.7A
Current Rating
Certifications
UL864
Edition / ULC-S527- 11 /
UL2572 Recognized
9th
NOTE: Refer to the Desigo CC System Description v2.1 for
computer specifications when Desigo CC is used in
non-UL864 / ULC-S527 applications.
–6–
Details for Ordering
SERVER Hardware / Software Packages
Model
Hardware
Category
DCC-W7I7-22L-S
Part Number
S54465-C10-A2
A or B
Description




DCC-W7I7-42L-S
S54465-C12-A2
A or B




C
DCC-W7XN-22L-S
S54465-C30-A2




C
DCC-W7XN-42L-S
S54465-C31-A2




DESIGO CC SERVER PACKAGE
UL / ULC Listed Workstation
22" (56 cm.) Monitor
Desigo CC software
NCC-2F interface card
DESIGO CC SERVER PACKAGE
UL / ULC Listed Workstation
42" (107 cm.) Monitor
Desigo CC software
NCC-2F interface card
DESIGO CC SERVER PACKAGE
UL / ULC Listed PC
22" (56 cm.) Monitor
Desigo CC software
NCC-2F interface card
DESIGO CC SERVER PACKAGE
UL / ULC Listed PC
42" (107 cm.) Monitor
Desigo CC software
NCC-2F interface card
CLIENT Hardware / Software Packages
Model
Hardware
Category
Part Number
A or B
S54465-C33-A2
DCC-W7I7-22L-C
Description



DCC-W7I7-42L-C
A or B
S54465-C34-A2



DESIGO CC CLIENT PACKAGE
UL / ULC Listed Workstation
22" Monitor
Desigo CC software
DESIGO CC CLIENT PACKAGE
UL / ULC Listed Workstation
42" Monitor
Desigo CC software
UL Listed Hardware Only > PCs
Model
Hardware
Category
Part Number
Description
UHW-W7I7-00L-M
A or B
S54465-C1-A2
UL / ULC Listed Workstation Hardware
− w / o Desigo CC SW, w / o Monitor
UHW-W7XN-00L-M
C
S54465-C2-A2
UL / ULC Listed SERVER PC Hardware with WIN7
− w / o Desigo CC SW, w / o Monitor
UL Listed Hardware Only > Monitors
Model
UHW-0000-22L-L
UHW-0000-42L-L
Part Number
Description
S54465-C8-A2
S54465-C9-A2
UL / ULC Listed 22" (56 cm.) Monitor
UL 864, 42" (107 cm.) Monitor
Network Interfaces
Model
Part Number
Description
Each order of Model MOSA consists of the following components:
MOSA
S54465-C62-A1
NCC-2F
500-849430
One (1) Model ENCL-01 enclosure with key-lock door
One (1) Model XND-M: XND-M (XNET interface) Module for MOSA
One (1) Model BRKT-M: Bracket for mounting an XND-M module to a Model ENCL-01 enclosure
One (1) Model S2E: Serial-to-Ethernet Module
One (1) Model PS-5A: Auxiliary 5V power supply module
UL 864 9th Edition Listed PC Interface Network Card for X-NET Systems
Network Switches
Model
SCALANCE X204-2
EIS6-100T/FT
EIS-ENCL
s I ndustry, Inc.
Building Technologies Division
Part Number
Description
500-650537
571-581
571-582
Multi-Mode Ethernet Fiber Switch
Multi-mode Ethernet Fiber Switch
Enclosure for Multi-mode Ethernet Fiber Switch
–7–
Details for Ordering ─ (continued)
NEW LICENSES – Required Software Licenses
Model
Part Number
Description
CCA-EXT-FSET
P55802-Y118-A100
New license for Extended Feature Set
CCA-1-CL
CCA-MAX-CL
P55802-Y119-A200
P55802-Y120-A200
New license for Add one (1) Client
New license for Add Max Clients
NEW LICENSES – Required Fire Safety Point Licenses
Model
Part Number
Description
CCA-100-FIRE
P55802-Y158-A412
Desigo CC license for new installs: Add 100 Fire dps
CCA-1000-FIRE
P55802-Y158-A413
Desigo CC license for new installs: Add 1,000 Fire dps
CCA-5000-FIRE
P55802-Y158-A453
Desigo CC license for new installs: Add 5,000 Fire dps
CCA-10000-FIRE
P55802-Y158-A414
Desigo CC license for new installs: Add 10,000 Fire dps
CCA-100-SCADA
P55802-Y124-A412
CCA-1000-SCADA
P55802-Y124-A413
Desigo CC license for new installs: Add 100 OPC Client Points
(and other general purpose Data Point [dps])
Desigo CC for new installs: Add 1000 OPC Client Points
(and other general purpose dps)
NEW LICENSES – Required Software Licenses, Video
Model
Part Number
Description
Video Option Plus
CCA-V-PLUS
P55802-Y159-A300
CCA-V-16MON
P55802-Y160-A401
CCA-V-16EMBC
P55802-Y162-A401
CCA-V-16EXTC
P55802-Y161-A401
License option to add the discipline Video to Desigo CC
The license includes eight (8) monitors; eight (8) embedded cameras,
and one (1) Siveillance VMS 200 embedded license
Add 16 monitors
License option to enable 16 additional monitors in Desigo CC
Add 16 embedded cameras
License extension to enable 16 additional embedded
cameras in Desigo CC and the embedded VMS
Add 16 external cameras
License extension to enable 16 additional embedded cameras in Desigo CC
Note: embedded camera licenses will be disabled
NEW LICENSES – Required Software Licenses, Access Control
Model
Part Number
Description
Add 16 doors
CCA-AC-16EXTD
P55802-Y164-A401
CCA-100-SEC
P55802-Y102-A412
CCA-1000-SEC
P55802-Y102-A413
New License extension to enable 16 additional doors of an external access-control system
Note: I/O’s are licensed as security points
Add 100 Security dps
New License extension to enable 100 Security data points
Add 1000 Security dps
New License extension to enable 1000 Security data points
NOTE: Access Control does not have an Access Control option license as the Video Module (CCA-V-PLUS). Door and security data point licenses are only required.
NEW LICENSES – Optional License, SiPass
Model
AAC-16-GMS
Part Number
P54511- P101-A1
Description
New License for adding the Desigo CC integration option to the SiPass integrated server.
Includes all necessary licenses to connect SiPass to Desigo CC.
Note: This license needs to be ordered through your SiPass rep.
s I ndustry, Inc.
Building Technologies Division
–8–
Details for Ordering ─ (continued)
NEW LICENSES – Optional Licenses
Model
Part Number
Description
CCA-OP-RENO
P55802-Y126-A300
Desigo CC: Add REMOTE NOTIFICATION (RENO) Option
CCA-OP-OPC
P55802-Y100-A300
Desigo CC: License for exposing dps as OPC-server dps to a 3rd-party OPC client
CCA-OP-AS-TR
P55802-Y103-A300
Desigo CC: Assisted Event Treatment Option
CCA-OP-RE-PR
P55802-Y104-A300
Desigo CC: Available options for the Reaction Processor
CCA-OP-LOG-V
P55802-Y132-A300
Desigo CC: License for the Log Viewer and Detailed Log
CCA-OP-WS-LIVE
P55802-Y163-A300
Desigo CC: License for live data for the Mobile App
(up to five [5] concurrent mobile apps users)
CCA-OP-WS-CMD
P55802-Y166-A300
Desigo CC: License for object commanding in the Mobile App
CCA-OP-WS-ADD
P55802-Y167-A300
Desigo CC: License to add one (1) more concurrent Mobile App user
NEW LICENSES – Optional Licenses, Accessories
Model
Part Number
DCC-EXSW-000-M
S54465-C47-A1
CMD.04
S55802-Y148
CCA-ENG
P55802-Y130-A100
Description
Desigo CC Installation DVD (with print manual)
USB license hardware key (dongle)
Hardware key is mandatory for Engineering Licenses (Model CCA-ENG)
One-year Engineering License
Provides access to all Desigo CC functionality for one year.
Engineering Licenses requires use of a hardware key (Model CMD.04)
RENEWAL LICENSES – Required Software Licenses
Model
Part Number
CCA-EXT-FSET-SUR
Desigo CC: Software License Renewal (SUR) for Extended Feature Set
CCA-1-CL-SUR
P55802-Y118-B100
P55802-Y119-B200
Description
CCA-MAX-CL-SUR
P55802-Y120-B200
Desigo CC: Software License Renewal (SUR) for Add Max Clients
Desigo CC: Software License Renewal (SUR) for Add one (1) Client
RENEWAL LICENSES – Fire Safety Point Licenses
Model
Part Number
Description
CCA-100-FIRE-SUR
P55802-Y158-B412
Desigo CC: Software License Renewal (SUR) for Add 100 Fire dps
CCA-1000-FIRE-SUR
P55802-Y158-B413
Desigo CC: Software License Renewal (SUR) for Add 1,000 Fire dps
CCA-5000-FIRE-SUR
P55802-Y158-B453
Desigo CC: Software License Renewal (SUR) for Add 5,000 Fire dps
CCA-10000-FIRE-SUR
P55802-Y158-B414
Desigo CC: Software License Renewal (SUR) for Add 10,000 Fire dps
CCA-100-SCADA-SUR
P55802-Y124-B412
Desigo CC Software License Renewal (SUR) for: Add 100 OPC Client Points
(and other general purpose Data Point [dps])
CCA-1000-SCADA-SUR
P55802-Y124-B413
Desigo CC Software License Renewal (SUR) for: Add 1000 OPC Client Points
(and other general purpose Data Point [dps])
RENEWAL LICENSES – Software License, Video
Model
Part Number
Description
Video Option Plus
License option to add the discipline Video to Desigo CC
The license includes eight (8) monitors; eight (8) embedded cameras,
and one (1) Siveillance VMS 200 embedded license
CCA-V-PLUS-SUR
P55802-Y159-B300
CCA-V-16MON-SUR
P55802-Y160-B401
CCA-V-16EMBC-SUR
P55802-Y162-B401
License extension to enable 16 additional embedded
cameras in Desigo CC and the embedded VMS
CCA-V-16EXTC-SUR
P55802-Y161-B401
License extension to enable 16 additional embedded cameras in Desigo CC
Note: embedded camera licenses will be disabled
Add 16 monitors
License option to enable 16 additional monitors in Desigo CC
Add 16 embedded cameras
Add 16 external cameras
s I ndustry, Inc.
Building Technologies Division
–9–
Details for Ordering ─ (continued)
RENEWAL LICENSES – Required Software License, Access Control
Model
Part Number
CCA-AC-16EXTD-SUR
P55802-Y164-B401
CCA-100-SEC-SUR
P55802-Y102-B412
CCA-1000-SEC-SUR
P55802-Y102-B413
Description
Add 16 doors
License extension to enable 16 additional
doors of an external access-control system
Note: I/O’s are licensed as security points
Add 100 Security dps
License extension to enable 100 Security data points
Add 1000 Security dps
License extension to enable 1000 Security data points
RENEWAL LICENSES – Optional Licenses
Model
Part Number
Description
CCA-OP-RENO-SUR
P55802-Y126-B300
Desigo CC: Add REMOTE NOTIFICATION (RENO) Option
[for software update renewal, SUR]
CCA-OP-OPC-SUR
S55802-Y100-B300
Desigo CC: License for exposing dps as OPC-server dps
to a 3rd-party OPC client [for SUR]
CCA-OP-AS-TR-SUR
P55802-Y103-B300
Desigo CC: Assisted Event Treatment Option [for SUR]
CCA-OP-RE-PR-SUR
P55802-Y104-B300
Desigo CC: Available options for the Reaction Processor [for SUR]
CCA-OP-LOG-V-SUR
P55802-Y132-B300
Desigo CC: License for the Log Viewer and Detailed Log [for SUR]
CCA-OP-WS-LIVE-SUR
P55802-Y163-B300
Desigo CC: License for live data for the Mobile App
(up to five [5] concurrent mobile apps users) – [for SUR]
CCA-OP-WS-CMD-SUR
P55802-Y166-B300
Desigo CC: License for object commanding in the Mobile App [for SUR]
CCA-OP-WS-ADD-SUR
P55802-Y167-B300
Desigo CC: License to add one (1) more concurrent Mobile App user [for SUR]
SERVICE LICENSES – Required Software Licenses
Model
Part Number
Description
CCA-EXT-FSET-SUS
P55802-Y118-C100
Software upgrade service (SUS) for Extended Feature Set
CCA-1-CL-SUS
P55802-Y119-C200
Software upgrade service (SUS) for Add one (1) Client
CCA-MAX-CL-SUS
P55802-Y120-C200
Software upgrade service (SUS) for Add Max Clients
SERVICE LICENSES – Fire Safety Point Licenses
Model
Part Number
CCA-100-FIRE-SUS
P55802-Y158-C412
Software upgrade service (SUS) for Add 100 Fire dps
CCA-1000-FIRE-SUS
P55802-Y158-C413
Software upgrade service (SUS) for Add 1,000 Fire dps
CCA-5000-FIRE-SUS
P55802-Y158-C453
Software upgrade service (SUS) for Add 5,000 Fire dps
CCA-10000-FIRE-SUS
P55802-Y158-C414
Software upgrade service (SUS) for Add 10,000 Fire dps
CCA-100-SCADA-SUS
P55802-Y124-C412
Software upgrade service (SUS) for Add 100 OPC Client Points
CCA-1000-SCADA-SUS
P55802-Y124-C413
Software upgrade service (SUS) for Add 1000 OPC Client Points
s I ndustry, Inc.
Building Technologies Division
Description
(and other general-purpose dps)
(and other general-purpose dps)
–10–
Details for Ordering ─ (continued)
SERVICE LICENSES – Required Software License, Video
Model
Part Number
Description
Video Option Plus
Service License option to add the discipline Video to Desigo CC
CCA-V-PLUS-SUS
P55802-Y159-C300
CCA-V-16MON-SUS
P55802-Y160-C401
CCA-V-16EMBC-SUS
P55802-Y162-C401
The license includes eight (8) monitors; eight (8) embedded
cameras, and one (1) Siveillance
VMS 200 embedded license
Add 16 monitors
Service License option to enable 16
additional monitors in Desigo CC
Add 16 embedded cameras
Service License extension to enable 16 additional embedded
cameras in Desigo CC and the embedded VMS
Add 16 external cameras
CCA-V-16EXTC-SUS
P55802-Y161-C401
Service License extension to enable 16 additional
embedded cameras in Desigo CC
Note: embedded camera licenses will be disabled
SERVICE LICENSES – Required Software License, Access Control
Model
Part Number
Description
P55802-Y164-C401
Service License extension to enable 16 additional
doors of an external access-control system
Add 16 doors
CCA-AC-16EXTD-SUS
Note: I/O’s are licensed as security points
CCA-100-SEC-SUS
P55802-Y102-C412
CCA-1000-SEC-SUS
P55802-Y102-C413
Add 100 Security dps
Service License extension to enable 100 Security data points
Add 1000 Security dps
Service License extension to enable 1000 Security data points
SERVICE LICENSES – Optional Licenses
Model
Part Number
CCA-OP-RENO-SUS
P55802-Y126-C300
Desigo CC: Add REMOTE NOTIFICATION (RENO) Option
[for software update service, SUS]
CCA-OP-OPC-SUS
P55802-Y100-C300
Desigo CC: License for exposing dps as OPC-server dps
to a 3rd-party OPC client [for SUS]
CCA-OP-AS-TR-SUS
P55802-Y103-C300
Desigo CC: License for Assisted Event Treatment Option [for SUS]
CCA-OP-RE-PR-SUS
P55802-Y104-C300
Desigo CC: License for available options for the Reaction Processor [for SUS]
CCA-OP-LOG-V-SUS
P55802-Y132-C300
Desigo CC: License for SW Service Upgrade Service (SUS)
for the Log Viewer and Detailed Log
CCA-OP-WS-LIVE-SUS
P55802-Y163-C300
Desigo CC: License for SW Service Upgrade Service (SUS)
for live data for the Mobile App
CCA-OP-WS-CMD-SUS
P55802-Y166-C300
Desigo CC: License for SW Service Upgrade Service (SUS)
for object commanding in the Mobile App
CCA-OP-WS-ADD-SUS
P55802-Y167-C300
Desigo CC: License for SW Service Upgrade Service (SUS)
for object commanding in the Mobile App
adding one (1) more concurrent Mobile App user
s I ndustry, Inc.
Building Technologies Division
Description
–11–
Notice: This marketing data sheet is not intended to be used for system design or installation purposes.
For the most up-to-date information, refer to each product’s installation instructions.
s Industry, Inc.
Building Technologies Division
Fire Safety
8 Fernwood Road
Florham Park, NJ 07932
Tel: (973) 593-2600
FAX: (908) 547-6877
URL: www.USA.Siemens.com/DesigoCC
(SII-FS)
Printed in U.S.A.
Fire Safety
1577 North Service Road
East Oakville, Ontario
L6H 0H6 / Canada
Tel: [905] 465-8000
URL: www.Siemens.CA
February 2017
Supersedes sheet dated 8/2016
(Rev. 7)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising