Operation Instructions

Fader Panel Operation with Control Remote

1.Product Descriptions

We wish to express our gratitude for your purchasing our digital product Fader

Panel. You now hold a premiere, hybrid 6-ch DMX controller combining with 6 channel faders. Its compact and portable design is convenient to mount and easy to operate for users. Its key features consists of as the following:

0

0

5

5

10

10

CH. 1

CH. 2

SC1

SC2

CH. 3 SC3

0 5 10

USITT DMX-512(1990) Multiplexed Digital Control

Up to 6 DMX channels and 6 channel control faders

6 programmable scenes, ability of up to 100 steps per scene

Assignable fade setting separately and Master control

Infrared remote control function

One preset pattern available for per scene

With a Control Panel DMX Distributor as tension provider and DMX signal converter in the entire system

US and EU versions optional

2.Control Panel View

Front Control View

0

0

0

5

5

10

10

60s 600s

MASTER/FADE

CH. 4

CH. 5

CH. 6

Fader Panel

SC4

SC5

SC6

OFF/PRO

Channel Faders(1~6):

Used to control the output level of each corresponding fixture channel.

Master Control Fader:

Used to control the overall output level for all Channels1~6 or control the master level for all Scenes.

Scene LED indicators(1~6):

These 6 LED's detail the current fader level for Scene's1-6. The LED indicators will reflect the fader level changes in real time.

OFF LED indicators:

To indicate the output state is turned on or off.

Scene Buttons(1~6):

To select the corresponding programmed scene to playback.

OFF Button:

To press the OFF button to close all channel1-6 output or enter/exit Recording Scene Mode.

LagoLED Control Remote for Fader Panel

Code: 95321004

Control Remote

RJ45 Interface:

To link with the Control Panel DMX Distributor via C-LAN cable for getting the tension and DMX output.

3.Operating Guide

3.1Recording Scenes

3.1.1 Recording Scenes Mode enables: press and hold the "OFF" button down for approximately 2 seconds or until the red

LED indicator next to the "OFF" button comes on, once the indicator is flashing, Record mode is engaged and you may

release the "OFF" button.

3.1.2 If the selected scene has been stored before, its indicator will be on. Press and hold the "Scene" button down for about

2 seconds and all LED indicators will flash repeatedly 3 times to delete it.

3.1.3 Select the "Scene" button where you wish to record to. The selected "Scene" LED will flash repeatedly.

3.1.4 Adjust the corresponding "Channel Fader" all ways up to ten(10) to set the desired fader level for the step of the scene.

Once you're satisfied with the setting, press the "Scene" button to store it. All LED indicators will flash repeatedly 3 times,

indicating that your the step of the scene has been recorded.

3.1.5 Repeat Step3.1.4 to record more steps for the scene, up to 100 Steps can be created per scene.

3.1.6 To record additional scenes, repeat Step3.1.3~3.1.5.

3.1.7 Once you've stored all of your scenes, press and hold the "OFF" button to exit. A blue LED next to the "OFF" button coming

on is indicative that you are out of the Recording Scene mode.

-Page 1-

3.2 Assigning Scenes Fade time

3.2.1 Press and hold the "Scene" button to select the Scene where you wish to assign fade time to, until its indicator is flashing.

3.2.2 Keep and hold the selected "Scene" button, and at the moment adjust the "Master control fader" all ways up to 600s to

set desired fader level.

3.2.3 Once you're satisfied with the setting, release the selected "Scene' button to store it. All LED indicators will flash repeatedly

3 times.

3.2.4 To assign fade time for additional scenes, repeat Step3.2.1 through 3.2.3.

Note: Once you've stored fade time for all of your scenes, please flip the "Master Control Fader" back to the initial position.

3.3 Set OFF Fade time

3.3.1 Recording Scene mode enables.

3.3.2 Adjust the "Master Control Fader" all ways up to 600s to set the desired level.

3.3.3 Once you're satisfied with the setting, tap the "OFF" button to store it. All LED indicators will flash repeatedly 3 times.

3.3.4 Exit the Recording Scene mode.

3.4 Set the Total Number of Controllable Channels

3.4.1 Disconnect the main power of Fader Panel.

3.4.2 Select the channel total number which you wish to control. When using the "Channel Fader 1", the channel total which

you wish to control is "1"; when using the "Channel Fader 2", the channel total which you wish to control is "2"; and in

the function, the channel total which you wish to control is up to "6".

3.4.3 Should adjust the "Master Control Fade" over 5 position when selecting the channel number.

3.4.4 Keep and hold the "OFF" button, and power the Fader Panel on, all LED indicators will come on. Release the "OFF" button,

and all LED indicators will flash repeatedly 3 times.

3.5 Playback Scenes

3.5.1 Only stored scenes can be playback.

3.5.2 Directly tap the "Scene" button to select the scene which you wish to playback.

3.5.3 Users can use the Infrared Remote to operate your Fader Panel.

3.6 Restore Scene

3.6.1 Disconnect the main power of the Fader Panel.

3.6.2 Keep and hold down the "Scene1" button which you wish to restore , and power the main power of the Fader Panel on,

until all Scenes' LED indicators will illuminate. Then release the "Scene" button to restore, and all Scenes' LED indicators

will flash repeatedly 3 times

4.Technical Specifications

Power Requirement

Connection

Housing

Ingress Protection Rating

Control Protocol

Listing

Operation temperature

Dimensions

Weights

12VDC

RJ45 interface

Polycarbonate

IP20

DMX-512 (1990)

CE certified

-10 degC to +50 degC

US:112(L) x 70(W) x 45(H)mm

EU: 86(L) x 86(W) x 45(H)mm

200g

Dimension 70mm 86mm

US version

EU version

-Page 2-

5.System Connection Diagram

Fader Panel

CH. 1

0 5 10

CH. 2

0

5

10

CH. 3

0 5 10

CH. 4

0 5 10

0 5 10

CH. 5

CH. 6

0 60s 600s

MASTER/FADE

SC1

SC2

SC3

SC4

SC5

SC6

OFF/PRO

Control Panel DMX distributor

Code: 95320231

AC 120V / 230V, 60/50Hz

0.5A max.

6 channel DMX output

Standard DMX cable

C-LAN cable

PIN-CONNECTION of RJ45 Interface

1. DMX OUT +

2. DMX OUT -

3. DMX IN +

4. GND

5. GND

6. DMX IN -

7. +12V

8. +12V

LagoLED Control Remote for Fader Panel

Code: 95321004

Control Remote

NOTE:

Effective distance from the infrared sensor of Fader Panel to Control Remote shall be limited within the range of 10m.

Otherwise, it results out of control.

-Page 3-

24-004-2161-00

Rev1.0