data sheet

BK600 SERIES
DATA SHEET
R-LINE DEVICES – BK600 SERIES
FEATURE
Radial leaded devices.
Very high voltage surge capabilities.
Available in lead-free version.
PACKAGE DIMENSIONS
D
E
SY
A
B
C
D
E
Max.
Max.
±0.6
Max.
Typ.
BK600-110
15.0
15.0
5.1
6.5
0.6
SY
BK600-150
15.0
15.0
5.1
6.5
0.6
SY
BK600-160
15.0
15.0
5.1
6.5
0.6
SY
Part Number
Style.
ELECTRICAL CHARACTERISTICS
IH
VMAX
IMAX
RMAX
RMIN
Pd typ.
(mA)
(V)
(A)
(ȍ)
(ȍ)
(W)
BK600-110
110
500
3
18
6
1.0
BK600-150
150
500
3
15
5
1.0
BK600-160
160
500
3
12
4
1.0
Part Number
IH=Hold current: maximum current at which the device will not trip at 25ć still air.
VMAXi =Maximum interrupt voltage device can withstand without damage at rated current.
IMAX=Maximum fault current device can withstand without damage at rated voltage.
RMAX=Maximum device resistance at 25ć prior to tripping.
RMIN=Minimum device resistance at 25ć prior to tripping.
Pdtyp=Typical power dissipation: typical amount of power dissipated by the device when at room temperature.
Revision:02-Nov-11
www.brightking.com
BK600 SERIES
THERMAL DERATING CHART - IH(mA)
Maximum Ambient Operating Temperatures (ć)
Part Number
-20
0
25
30
40
50
60
70
85
BK600-110
152
131
110
100
91
80
70
61
46
BK600-150
207
179
150
137
125
110
96
83
63
BK600-160
221
190
160
146
133
117
102
88
67
TEST PROCEDURES AND REQUIREMENT
Test
Test Conditions
Accept/Reject Criteria
Resistance
In still air @25ć
Rmin ” R ” Rmax
Time to Trip
Specified current,Vmax,25ć
T ” max. Time to trip(Ttirp)
Hold Current
30 min, at IH
No trip
Trip Cycle Life
Vmax, Imax,100 cycles
No arcing or burning
Trip Endurance
Vmax,24hours
No arcing or burning
TYPICAL TIME-TO-TRIP CHARTS @ 25ć
Time-to-trip (s)
A = BK600-110
B = BK600-150
C = BK600-160
Fault current (A)
STORAGE RECOMMENDATIONS
1. Storage Temperature : -10°C ~+40°C
2. Relative Humidity :
̰80%RH
3. Keep away from corrosive atmosphere and sunlight.
4. Period of Storage: 1 year.
Revision:02-Nov-11
www.brightking.com
BK600 SERIES
WAVE SOLDERING RECOMMENDATION PARAMETERS
300
3-5S
250
Temperature (°C)
Soldering
245°C 260°C
200
Pre-heating
150
100°C 130°C
100
Cooling
50
0
0
50
150
100
200
250
Time(s)
Items
Conditions
Pre-Heating Zone
Refer to the condition recommended by the flux manufacturer. Maximum
ramping rate should not exceed 4ć/sec.
Soldering Zone
Cooling Zone
Maximum solder temperature should not exceed 260ć
Forced cooling
MANUAL SOLDERING RECOMMENDATION PARAMETERS
Items
Conditions
Soldering condition
The most highest power of the manual soldering electric iron should be 30W or
lower than that, soldering temperature should not be higher than 280ć.
Soldering time
The soldering time should be within 3 seconds, or it may lead to the envelope
layer cracking, resistance getting bigger.
Soldering position
Other
The soldering position should be controlled distance sea1de feet 4mm above.
The iron soldering head can’t touch the body of the product except the lead wire.
In the conditions of meeting soldering effect of the product, the soldering lower
temperature, nearest distance from the soldering position to chip and less
soldering time will make the soldering better.
Notes: 1. Before using the device must be stored in the original bags, if the storage conditions do not
guarantee, the device may not be able to meet the given value.
2. The devices can't used for reflow soldering.
Revision:02-Nov-11
www.brightking.com

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project