warning warning

warning warning
STAR450-315TM WIRELESS
ACCESS CONTROL
RECEIVER
SPECIFICATIONS
SUPPLY VOLTAGE: 12-24 VOLTS AC OR DC
OPERATING CURRENT: 250 mA MAXIMUM
OPERATING TEMP RANGE: -40 TO +149F
(-40 TO +65C)
FREQUENCY: 315 MHz
RELAY CONTACT RATING: 1 AMP @ 24 VOLTS AC OR DC
This device complies with FCC Rules Part 15 and IC Canada Rules
and Regulations. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Removable memory modules and RF module are included in this
product. Jumper J2 must remain in the default position unless
otherwise noted. THERE ARE NO OTHER SERVICEABLE PARTS.
WARNING
WARNING
CAUTION
WARNING
TABLE OF CONTENTS
DESCRIPTION
PAGE
Mounting Instructions for STAR450 . . . . . . . . . . . . . . . . . . . . . .1
Programming For STAR450 . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Electrical Connections for STAR450 . . . . . . . . . . . . . . . . . . . . . .4
STAR450 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is not connected BEFORE installing the receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
MOUNTING INSTRUCTIONS FOR STAR450
Location: Select a convienent location near your device to be
controlled by the STAR450. For best performance, the STAR450
should be mounted in “Line-Of-Sight” with your intended
transmitting location. Avoid mounting the STAR450 in or on
metallic enclosures. If this is unavoidable, we recommend
installing the antenna extension kit (86LM) for best results. See
Remote Antenna Mounting for proper installation.
Receiver Mounting: Mount Backplate to desired surface using #6
hardware (Not provided). Hardware used will depend on on
mounting application. (Refer to figure 1 for Receiver mounting
hole locations). Wire electrical connections to unit. Snap Unit to
Back Plate.
Direct Antenna Mounting: Install the supplied antenna onto the
STAR450 antenna connector by screwing the connector
clockwise. Slide the seal boot down to meet the O-Ring, covering
the antenna hardware.
Figure 2
Remote Antenna Mounting: Use the optional 86LM antenna
extension kit to mount the remote antenna as high and far from
metal as possible for best radio range (Figure 2). Contact
LiftMaster customer service at: 1-800-528-2806 to order the
model 86LM.
Figure 1
Antenna
Seal Boot
Antenna
Connector
STAR450 FEATURES
POWER INDICATOR
SCROLLING DASHES ON
DIGITAL DISPLAY WHEN
AC OR DC POWER IS
APPLIED TO THE UNIT.
DIGITAL DISPLAY
DISPLAYS REMOTE CONTROL LOCATION
NUMBERS WHEN PROGRAMMING OR
ACCESS IS GRANTED. ALSO DISPLAYS
USER PROMPTS AND MESSAGES.
ANTENNA CONNECTION
FOR CONNECTION TO THE
DIRECT ANTENNA OR THE
ANTENNA EXTENSION KIT.
DELETE KEY
USED TO DELETE A REMOTE CONTROL
FROM THE SELECTED MEMORY LOCATION
ADD KEY
USED TO ENTER REMOTE CONTROLS
AND ENTER RAPID LEARNTM MODE.
Add
Delete
Block
1
4
7
*
2
5
8
0
3
6
9
BLOCK KEY
USED TO BLOCK THE
RECEIVER FROM
GRANTING ACCESS TO
THE SELECTED REMOTE
CONTROL. REMOTE CONTROL
REMAINS IN MEMORY, AND
MAY BE UNBLOCKED IN
THE FUTURE.
NUMERIC KEYPAD
USED FOR PROGRAMMING
AND QUERYING REMOTE CONTROL
LOCATIONS. ALSO USED TO ENTER
ADVANCED FUNCTIONS.
#
STAR KEY
USED TO ENTER ADVANCED FUNCTIONS:
*, 1- LAST REMOTE CONTROL RECEIVED
*, 2- NO. OF UNUSED MEMORY LOCATIONS
*, 3- NO. OF OCCUPIED MEMORY LOCATIONS
*, 4- NO. OF BLOCKED REMOTE CONTROL LOCATIONS
*, 5- FIRST BLOCKED REMOTE CONTROL LOCATION
*, 7- SOFTWARE VER. #
*, 0- AUDIBLE DIAGNOSTICS OFF/ON
POUND KEY
USED AS AN ESC OR EXIT KEY FOR ALL
FUNCTIONS OR MODES.
PROGRAMMING THE STAR450
Rapid LearnTM- Add remote control to next available location.
AUTO
001
#
TO EXIT
Add
PRESS
PRESS
PRESS
Add
Adding Remote control- Add remote control to a specific location.
AUTO
001
Add
002
023
234
2
3
4
ENTER LOCATION (1-450)
PRESS
#
PRESS
TO EXIT
PRESS
Add
Deleting a Remote control- To delete a user.
Del
Delete
PRESS
002
023
234
2
3
4
ENTER LOCATION (1-450)
2
Del
Delete
PRESS
TO
CONFIRM
END
PROGRAMMING THE STAR450 (CON’T)
Blocking (Unblocking) a Remote control- To block or unblock a user.
bLc
Block
002
023
234
2
3
4
bLc
END
Block
ENTER LOCATION (1-450)
PRESS
PRESS
TO
CONFIRM
(UNBLOCK)
Un-
bLc
Duplicating Memory- Allows user to back up programmed remote control memory into the provided backup memory module.
Main Memory Module
dup
*
6
,
PRESS SIMULTANEOUSLY
END
~6 SECONDS
Backup Memory
Module
NOTE: To duplicate memory, plug memory module into back up
slot and press *,6. Once duplication is complete, remove the
backup memory module and store in a separate location.
Restoring Memory- To restore memory, simply place the
duplicate memory module from the backup memory location in
the main memory position.
location of last remote control received.
* 12 Memory
# of open remote control locations.
* 3 # of locations occupied.
* 4 # of blocked remote control locations.
* 5 First blocked remote location.
* 5 Next blocked location (Repeat to scroll).
memory- See Duplicating memory.
* 67 Duplicate
Version #
* # Press to exit functions.
ADVANCED FUNCTIONS
Step 1. For advanced functions, press and hold the (*) key
and a number key at the same time to select the corresponding
advanced function. (See table at right for available functions.)
Press the ‘#’ key to exit the function.
*
0 Audible diagnostics OFF/ON
(LED will be displayed when OFF)
If no remote controls are programmed into the star450,
then (---) will be displayed.
AUDIBLE DIAGNOSTICS
Step 1. Activate Remote control.
Step 2. Listen for beep.
(LED will be displayed when OFF)
Double Beep- Remote control is valid & programmed into STAR450
accompanied by remote control location display.
Slow Beep- Security+ Remote control (Not programmed in STAR450).
Long Beep- Blocked remote control.
®
No Beep-
Remote control not working.
KEYPAD SOUND ALERTS
Triple Beep- Confirmation of Delete.
Single Beep- Key Pressed.
Double Beep- Confirmation of an accepted Tx
or valid Add/Block input.
Long Beep- Blocked Tx, Error, or
Out of Range
Display
OPn
Occ
bLc
Out
REMOTE CONTROL LOCATION QUERY
Step 1. Enter a remote control location number (001-450) to view
location status (See table to the right for possible status displays).
3
Description
Remote control location is empty
Remote control location is occupied
Remote control location is blocked
Remote control location is out of
range(not between 1 & 450)
Beeper
no beep
no beep
no beep
long beep
TROUBLESHOOTING GUIDE
Problem
Probable Cause(s)
Solution(s)
No display
1. Faulty/intermittent power connections to
unit Or
2. No power to unit
1. Check power connnections to unit
2. Supply power to unit
No beep when
transmitting
Audible diagnostics may have been turned
OFF (right-most decimal point will be lit on
the display)
Press "*" and "0" keys at the same time
Remote control does
not activate operator
1. Remote control not programmed into
system Or
2. Remote control is blocked Or
3. Remote control battery is dead
1. Add remote control to memory
2. Pay your rent
3. Replace remote control battery
Remote control won't
program into memory
1. Memory may be full Or
2. Remote control may not be a recognized
Chamberlain remote control Or
3. Remote control battery is dead
1. Delete unused remote controls from memory
2. Verify remote control is listed in compatible
remote controls section Or
3. Replace remote control battery
Unit does not function, Main memory module missing or damaged
[E 1] displayed
Replace main memory module
Duplication function
does not work,
[E 2] displayed
Backup memory module missing or
damaged - If included
Replace backup memory module
Keypad does not
respond,
[E 3] displayed
Keypad has a stuck key
Cycle power.
If unit exhibits this condition again after 2
minutes, contact Technical Service
ELECTRICAL CONNECTIONS FOR STAR450
Receiver (Bottom)
Receiver (Bottom)
Wall Button
Wall Button
Opener
Trans Primary
Trans Primary
Model 85
Transformer
To wall
outlet
To wall outlet
STAR450 COMPATIBLE REMOTE CONTROLS
Security+® Remote Controls
Security+® Keypads
371LM
372LM
370LM
374LM
376LM
Passport Remote Control
CPT43
CPT13
CPT23
CPT33
For highest level of security, we recommend the Security+ remote control family
®
01-32546
Model 95
Transformer
STAR450 OPTIONAL ACCESSORIES
CGI Part Number
71-65WTBOX
Description
Watertight Box Field Install Kit
86LM
Antenna Extension Kit
85LM
24VAC transformer w/barrel connector
95LM
24VAC transformer w/screw terminals
HOW TO ORDER REPAIR PARTS
OUR LARGE SERVICE ORGANIZATION
SPANS AMERICA
INSTALLATION AND SERVICE INFORMATION
ARE AVAILABLE 6 DAYS A WEEK
CALL OUR TOLL FREE NUMBER - 1-800-528-2806
MONDAY Through FRIDAY 5:00 a.m. TO 6:00 p.m. (MST)
SATURDAY 7:00 a.m. TO 3:30 p.m. (MST)
WWW.LIFTMASTER.COM
©2005, The Chamberlain Group, Inc.
All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising