Removing the Hard Disk Drive

Removing the Hard Disk Drive
Disassembly
Removing the Hard Disk Drive
Figure 3
The hard disk drive is mounted in a removable case and can be taken out to accommodate other 2.5" SATA hard disk
drives with a height of 9.5mm (h). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
HDD Assembly
Removal
a. Remove the screws.
b. Remove the cover
Hard Disk Upgrade Process
1. Turn off the computer, and turn it over and remove the battery (page 2 - 5).
2. Locate the Hard disk bay cover and remove screws 1 & 2 .
3. Remove the bay cover 3 .
b.
a.
2.Disassembly
1
2
3
4. Hard disk Bay Cover
• 3 Screws
Removing the Hard Disk Drive 2 - 7
Disassembly
Figure 4
2.Disassembly
HDD Assembly
Removal (cont’d.)
c. Remove the screws.
d. Lift the hard disk assembly using two hands at
points 9 - 10 .
e. Lift the hard disk assembly up out off the computer.
f. Remove the HDD(s) from
the connector
g. Remove the screws and
separate the HDD(s)
from case.
Remove screws 4 - 7 and pull the tab to disconnect the connector 8 from hard disk assembly.
Carefully lift the hard disk assembly using two hands at points 9 - 10 .
Lift the hard disk assembly 11 out of the computer.
Separate the hard disk board connector 12 from the hard disk assembly.
Remove screws 13 - 24 (depending on how many hard disks you have installed in the assembly).
Separate the hard disk(s) 25 and hard disk mylar 26 from the case 27 .
Reverse the process to install a new hard disk(s) and make sure to connect cable 8 before screwing in screws
4 - 7 (Figure c).
c.
g.
e.
4.
5.
6.
7.
8.
9.
10.
13
8
16
4
14
5
26
15
25
6
7
17
19
18
20
21
d.
11
10
11 Hard Disk Assembly
12 Hard Disk Board
Connector
25. Hard Disks
26. Hard Disk Mylar
27. Hard Disk Case
• 16 Screws
2 - 8 Removing the Hard Disk Drive
22
27
23
24
9
f.
25
11
12
Disassembly
Removing the Hard Disk(s) in the Secondary HDD Bay
1.
2.
3.
4.
5.
6.
7.
Figure 5
Turn off the computer, and turn it over and remove the battery.
The secondary hard disk bay is located under the battery.
Remove screws 1 - 4 from the secondary hard disk assembly.
Grip the tab 5 and slide the hard disk assembly in the direction of the arrow 6 .
Lift the hard disk assembly 7 out of the compartment.
Remove the screws 8 - 11 to release the hard disk 12 from the case 13 .
Reverse the process to install any new hard disk(s).
Secondary HDD
Assembly Removal
c.
a.
7
b.
8
d.
9
1
5
4
2
6
13
10
7. Hard Disk Assembly
12. Hard Disk Case
13. Hard Disks
• 8 Screws
3
11
12
Removing the Hard Disk Drive 2 - 9
2.Disassembly
a. Remove the battery.
b. Remove the screws and
slide the secondary hard
disk assembly in the direction of the arrow.
c. Lift the secondary hard
disk assembly out off
the computer.
d. Remove the screws to
release the hard disk
from the case.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising