Leam Amplifier Instructions for Use

Leam Amplifier Instructions for Use
Leam Amplifier
Instructions for Use
Introduction
This amplifier has been designed to mix up to 6 separate mono inputs (microphones
etc. as well as one stereo input from a CD or tape player.
Village Outreach can also supply microphones (wired, radio, handheld or lapel), and
microphone stands if required.
If you have any problems with setting it up which cannot be resolved by reading the
instructions on the following pages then please call us on 01588 630097.
If you find any features don’t work (e.g. faulty leads or switches) then please tell us
when you return the equipment so we can fix them before hiring it out to another
customer.
The amplifier is supplied with:
•
Two Speakers
•
Two Speaker Leads (one longer than the other)
•
Two Speaker Tripods
•
One Microphone
•
One iPod/PC Connection Lead
•
Mains Cable
When ordering the system you need to consider if you need a mains extension lead.
We recommend that once you have set up the speakers you get the system working
with just a wired microphone before connecting anything else, even if you do not
intend to use a microphone. This proves the amplifier and speakers are working and
the sound levels are reasonable before adding any other connections.
Connecting Up the System
1. Erect the two speaker stands and mount the speakers on each one. beware,
they are heavy and it should be done by two people. The speakers just slot on
top of the stands.
2. Connect a speaker cable to each speaker and run it back to the amplifier, one
of the speaker cables is longer than the other, the plugs are the same at both
ends.
C
ins
a
M
h
e in
l
b
a
er e
Speakers plug in here
3. The microphone leads can be plugged into any of the six sockets on the front
of the amplifier. Make sure the “Level” control (Volume) is turned right
down.
Volume
The Effect Control
should be at zero
Pad Switch out
Microphone
Leave these controls
(Pan, Low & High)
in the upright position
4. Turn the master level controls shown below to about the middle position
position.
Set both level controls
to mid position
The amp is now ready for use. Switch it on (switch at top right hand corner of
the front) and check the red power on light on the front panel comes on.
Ensure the switch on the microphone is on, turn up the microphone volume
until you can hear yourself through the speakers.
If you hear a Loud Screech this indicates you have the microphone volume
too high which induces feedback. Turn down the volume and/or move the
microphone so it is not directly in front of a speaker.
Now it is working adjust the master levels so the volume is right for your
event, each speaker is controlled from a different control.
More microphones can be plugged in channels 2-6 the volume of each can be
independently controlled allowing you to mix different inputs together.
Now you have a basic system up and running you can add other sources as
described below.
5. Adding a Tape, iPad or CD Player.
Channels 1-6 are mono, i.e. one source. Channel 7 has two line inputs so you
can plug the left and right channels of a stereo system into the amplifier.
The lead we provide for iPods has two phono plugs which go in the red and
white sockets marked "Play" shown below
C ha
nne
l
two 7 for A
u
soc
kets dio, u
mar se th
e
ked
“Pla bottom
y”
om
e fr n
m
olu
itio
d v d pos
n
u
i
so
m
the in the
s
t
it
l se
tro rt with
n
o
sta
el c
lev nput,
p
i
o
t
io
The e aud
th
6. Radio Microphone
If you wish to use the radio microphone from Village Outreach the output
from the radio receiver should be plugged into a “Line Input” socket.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising