Wireless LAN Device Series

Wireless LAN Device Series
Wireless LAN Device Series
OT-2615
Manual do Usuário
v20080312
Prefácio
Para usar este guia, você deve ter experiência com
configurações TCP/IP e estar familiarizado com os conceitos e
terminologias de redes locais sem fio.
O endereço padrão para o OT-2615 é 192.168.1.254
Ele levará 55 segundos para completar a sequência de boot
depois de ligado na energia.
Conteúdo do Kit
Antes de começar a instalar o OT-2615, certifique-se de que o Kit
contém os seguintes itens:
* Antena em caixa plástica, com o roteador
* Adaptador de energia POE 48VDC@ 400mA
* Cabo de energia
* Abraçadeiras
* Esquema de montagem
Antes de começar
O OT-2615 é enviado com a seguinte configuração padrão.
Default IP Address: 192.168.1.254
Default IP subnet mask: 255.255.255.0
WEB login User Name: <empty>
WEB login Password: <empty>
O dispositivo tem 3 modos de operação (Gateway/Bridge/WISP).
Prepare your PC to configure the WLAN Broadband Router
For OS of Microsoft Windows 95/ 98/ Me:
1. Click the Start button and select Settings, then click Control Panel. The
Control Panel window will appear.
Note: Windows Me users may not see the Network control panel. If so,
select View all Control Panel options on the left side of the window
2. Move mouse and double-click the right button on Network icon. The
Network window will appear.
3. Check the installed list of Network Components. If TCP/IP is not installed,
click the Add button to install it; otherwise go to step 6.
4. Select Protocol in the Network Component Type dialog box and click Add
button.
5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then
click OK button to install the TCP/IP protocol, it may need the Microsoft
Windows CD to complete the installation. Close and go back to Network
dialog box after the TCP/IP installation.
6. Select TCP/IP and click the properties button on the Network dialog box.
7. Select Specify an IP address and type in values as following example.
 IP Address: 192.168.1.1, any IP address within 192.168.1.1 to
192.168.1.253 is good to connect the Wireless LAN Access Point.
 IP Subnet Mask: 255.255.255.0
8. Click OK and reboot your PC after completes the IP parameters setting.
For OS of Microsoft Windows 2000, XP:
1. Click the Start button and select Settings, then click Control Panel. The
Control Panel window will appear.
2. Move mouse and double-click the right button on Network and Dial-up
3.
4.
5.
6.
7.
8.
Connections icon. Move mouse and double-click the Local Area
Connection icon. The Local Area Connection window will appear. Click
Properties button in the Local Area Connection window.
Check the installed list of Network Components. If TCP/IP is not installed,
click the Add button to install it; otherwise go to step 6.
Select Protocol in the Network Component Type dialog box and click Add
button.
Select TCP/IP in Microsoft of Select Network Protocol dialog box then
click OK button to install the TCP/IP protocol, it may need the Microsoft
Windows CD to complete the installation. Close and go back to Network
dialog box after the TCP/IP installation.
Select TCP/IP and click the properties button on the Network dialog box.
Select Specify an IP address and type in values as following example.
 IP Address: 192.168.1.1, any IP address within 192.168.1.1 to
192.168.1.253 is good to connect the Wireless LAN Access Point.
 IP Subnet Mask: 255.255.255.0
Click OK to completes the IP parameters setting.
For OS of Microsoft Windows NT:
1. Click the Start button and select Settings, then click Control Panel. The
Control Panel window will appear.
2. Move mouse and double-click the right button on Network icon. The
Network window will appear. Click Protocol tab from the Network window.
3. Check the installed list of Network Protocol window. If TCP/IP is not
installed, click the Add button to install it; otherwise go to step 6.
4. Select Protocol in the Network Component Type dialog box and click Add
button.
5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then
click OK button to install the TCP/IP protocol, it may need the Microsoft
Windows CD to complete the installation. Close and go back to Network
dialog box after the TCP/IP installation.
6. Select TCP/IP and click the properties button on the Network dialog box.
7. Select Specify an IP address and type in values as following example.
 IP Address: 192.168.1.1, any IP address within 192.168.1.1 to
192.168.1.253 is good to connect the Wireless LAN Access Point.
 IP Subnet Mask: 255.255.255.0
8. Click OK to complete the IP parameters setting.
1.1Connect to the WLAN Broadband Router
Open a WEB browser, i.e. Microsoft Internet Explore, then enter
192.168.1.254 on the URL to connect the WLAN Broadband Router.
1.2Management and configuration on the WLAN Broadband Router
1.2.1Status
This page shows the current status and some basic settings of the
device, includes system, wireless, Ethernet LAN and WAN
configuration information.
Screen snapshot – Status
Item
System
Uptime
Firmware version
Description
It shows the duration since WLAN Broadband
Router is powered on.
It shows the firmware version of WLAN
Broadband Router.
Wireless configuration
Mode
It shows wireless operation mode
Band
It shows the current wireless operating
frequency.
SSID
It shows the SSID of this WLAN Broadband
Router.
The SSID is the unique name of WLAN
Broadband Router and shared among its service
area, so all devices attempts to join the same
wireless network can identify it.
Channel Number
It shows the wireless channel connected
Encryption
BSSID
Associated Clients
currently.
It shows the status of encryption function.
It shows the BSSID address of the WLAN
Broadband Router. BSSID is a six-byte address.
It shows the number of connected clients (or
stations, PCs).
TCP/IP configuration
Attain IP Protocol
It shows type of connection.
IP Address
It shows the IP address of LAN interfaces of
WLAN Broadband Router.
Subnet Mask
It shows the IP subnet mask of LAN interfaces
of WLAN Broadband Router.
Default Gateway
It shows the default gateway setting for LAN
interfaces outgoing data packets.
DHCP Server
It shows the DHCP server is enabled or not.
MAC Address
It shows the MAC address of LAN interfaces of
WLAN Broadband Router.
WAN configuration
Attain IP Protocol
It shows how the WLAN Broadband Router gets
the IP address. The IP address can be set
manually to a fixed one or set dynamically by
DHCP server or attain IP by PPPoE / PPTP
connection.
IP Address
It shows the IP address of WAN interface of
WLAN Broadband Router.
Subnet Mask
It shows the IP subnet mask of WAN interface of
WLAN Broadband Router.
Default Gateway
It shows the default gateway setting for WAN
interface outgoing data packets.
DNS1/DNS2/DNS3
It shows the DNS server information.
MAC Address
It shows the MAC address of WAN interface of
WLAN Broadband Router.
1.2.2Setup Wizard
This page guides you to configure wireless broadband router for first
time
Screen snapshot – Setup Wizard
1. Operation Mode
This page followed by Setup Wizard page to define the
operation mode.
Screen snapshot – Operation Mode
2. Time Zone Setting
This page is used to enable and configure NTP client
Screen snapshot – Time Zone Settings
3. LAN Interface Setup
This page is used to configure local area network IP address and
subnet mask
Screen snapshot – LAN Interface Setup
4. WAN Interface Setup
This page is used to configure WAN access type
Screen snapshot – WAN Interface Setup
5. Wireless Basic Settings
This page is used to configure basic wireless parameters like
Band, Mode, Network Type SSID, Channel Number, Enable
Mac Clone(Single Ethernet Client)
Screen snapshot – Wireless Basic Settings
6. Wireless Security Setup
This page is used to configure wireless security
Screen snapshot – Wireless Security Setup
1.2.3Operation Mode
This page is used to configure which mode wireless broadband router
acts
Screen snapshot – Operation Mode
Item
Gateway
Bridge
Description
Traditional gateway configuration. It always
connects internet via ADSL/Cable Modem. LAN
interface, WAN interface, Wireless interface, NAT
and Firewall modules are applied to this mode
Each interface (LAN, WAN and Wireless) regards
Wireless ISP
Apply Changes
Reset
as bridge. NAT, Firewall and all router’s functions
are not supported
Switch Wireless interface to WAN port and all
Ethernet ports in bridge mode. Wireless interface
can do all router’s functions
Click the Apply Changes button to complete the
new configuration setting.
Click the Reset button to abort change and recover
the previous configuration setting.
1.2.4Wireless - Basic Settings
This page is used to configure the parameters for wireless LAN clients
that may connect to your Broadband Router. Here you may change
wireless encryption settings as well as wireless network parameters.
Screen snapshot – Wireless Basic Settings
Item
Disable Wireless
LAN Interface
Band
Mode
Description
Click on to disable the wireless LAN data
transmission.
Click to select 2.4GHz(B) / 2.4GHz(G) /
2.4GHz(B+G)
Click to select the WLAN AP / Client / WDS /
AP+WDS wireless mode.
Site Survey
SSID
Channel Number
Associated Clients
Enable Mac Clone
(Single Ethernet
Client)
Enable Universal
Repeater Mode
SSID of Extended
Interface
Apply Changes
Reset
The Site Survey button provides tool to scan the
wireless network. If any Access Point or IBSS is
found, you could choose to connect it manually
when client mode is enabled. Refer to 3.3.9 Site
Survey.
It is the wireless network name. The SSID can be
32 bytes long.
Select the wireless communication channel from
pull-down menu.
Click the Show Active Clients button to open
Active Wireless Client Table that shows the MAC
address, transmit-packet, receive-packet and
transmission-rate for each associated wireless
client.
Take Laptop NIC MAC address as wireless client
MAC address. [Client Mode only]
Click to enable Universal Repeater Mode
Assign SSID when enables Universal Repeater
Mode.
Click the Apply Changes button to complete the
new configuration setting.
Click the Reset button to abort change and recover
the previous configuration setting.
1.2.5Wireless - Advanced Settings
These settings are only for more technically advanced users who have a
sufficient knowledge about wireless LAN. These settings should not be
changed unless you know what effect the changes will have on your
WLAN Broadband Router.
Screen snapshot – Wireless Advanced Settings
Item
Authentication Type
Fragment Threshold
RTS Threshold
Beacon Interval
Data Rate
Preamble Type
Description
Click to select the authentication type in Open
System, Shared Key or Auto selection.
Set the data packet fragmentation threshold, value
can be written between 256 and 2346 bytes.
Refer to 4.10 What is Fragment Threshold?
Set the RTS Threshold, value can be written
between 0 and 2347 bytes.
Refer to 4.11 What is RTS(Request To Send)
Threshold?
Set the Beacon Interval, value can be written
between 20 and 1024 ms.
Refer to 4.12 What is Beacon Interval?
Select the transmission data rate from pull-down
menu. Data rate can be auto-select, 11M, 5.5M,
2M or 1Mbps.
Click to select the Long Preamble or Short
Preamble support on the wireless data packet
transmission.
Refer to 4.13 What is Preamble Type?
Broadcast SSID
Click to enable or disable the SSID broadcast
function.
Refer to 4.14 What is SSID Broadcast?
IAPP
Click to enable or disable the IAPP function.
Refer to 4.20 What is Inter-Access Point
Protocol(IAPP)?
802.11g Protection
Protect 802.11b user.
RF Output Power
To adjust transmission power level.
Turbo Mode
Click to Enable/Disable turbo mode.(Only apply
to WLAN IC of Realtek).
Block Relay Between Click Enabled/Disabled to decide if blocking
Clients
relay packets between clients.
WMM
Click Enabled/Disabled to init WMM feature.
ACK Timeout
Set ACK timeout value. It shows current time in
the end.
Apply Changes
Click the Apply Changes button to complete the
new configuration setting.
Reset
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.6Wireless - Security Setup
This page allows you setup the wireless security. Turn on WEP, WPA,
WPA2 by using encryption keys could prevent any unauthorized access
to your wireless network.
Screen snapshot – Wireless Security Setup
Item
Encryption
Description
Select the encryption supported over wireless
access. The encryption method can be None,
Use 802.1x
Authentication
WPA Authentication
Mode
Pre-Shared Key
Format
Pre-Shared Key
Enable PreAuthentication
Authentication
RADIUS Server
Apply Changes
Reset
WEP, WPA(TKIP), WPA2 or WPA2 Mixed
Refer to 4.9 What is WEP?
4.15 What is Wi-Fi Protected Access (WPA)?
4.16 What is WPA2(AES)?
4.17 What is 802.1X Authentication?
4.18 What is Temporal Key Integrity Protocol
(TKIP)? 4.19 What is Advanced Encryption
Standard (AES)?
While Encryption is selected to be WEP.
Click the check box to enable IEEE 802.1x
authentication function.
Refer to 4.16 What is 802.1x Authentication?
While Encryption is selected to be WPA.
Click to select the WPA Authentication Mode
with Enterprise (RADIUS) or Personal (PreShared Key).
Refer to 4.15 What is Wi-Fi Protected Access
(WPA)?
While Encryption is selected to be WPA.
Select the Pre-shared key format from the pulldown menu. The format can be Passphrase or
Hex (64 characters). [WPA, Personal(PreShared Key) only]
Fill in the key value. [WPA, Personal(Pre-Shared
Key) only]
Click to enable Pre-Authentication.
[WPA2/WPA2 Mixed only, Enterprise only]
Set the IP address, port and login password
information of authentication RADIUS sever.
Click the Apply Changes button to complete the
new configuration setting.
Click the Reset button to abort change and
recover the previous configuration setting.
7. WEP Key Setup
Screen snapshot – WEP Key Setup
Item
Key Length
Key Format
Default Tx Key
Encryption Key 1
Encryption Key 2
Encryption Key 3
Encryption Key 4
Apply Changes
Close
Reset
Description
Select the WEP shared secret key length from
pull-down menu. The length can be chose
between 64-bit and 128-bit (known as “WEP2”)
keys.
The WEP key is composed of initialization vector
(24 bits) and secret key (40-bit or 104-bit).
Select the WEP shared secret key format from
pull-down menu. The format can be chose
between plant text (ASCII) and hexadecimal
(HEX) code.
Set the default secret key for WEP security
function.
Value can be chose between 1 and 4.
Secret key 1 of WEP security encryption function.
Secret key 2 of WEP security encryption function.
Secret key 3 of WEP security encryption function.
Secret key 4 of WEP security encryption function.
Click the Apply Changes button to complete the
new configuration setting.
Click to close this WEP Key setup window.
Click the Reset button to abort change and
recover the previous configuration setting.
WEP encryption key (secret key) length:
Length
Format
ASCII
HEX
64-bit
128-bit
5 characters
10 hexadecimal codes
13 characters
26 hexadecimal codes
1.2.7Wireless - Access Control
If you enable wireless access control, only those clients whose wireless
MAC addresses are in the access control list will be able to connect to
your Access Point. When this option is enabled, no wireless clients will
be able to connect if the list contains no entries.
Screen snapshot – Wireless Access Control
Item
Wireless Access
Control Mode
MAC Address
Comment
Apply Changes
Reset
Current Access
Description
Click the Disabled, Allow Listed or Deny Listed
of drop down menu choose wireless access
control mode.
This is a security control function; only those
clients registered in the access control list can link
to this WLAN Broadband Router.
Fill in the MAC address of client to register this
WLAN Broadband Router access capability.
Fill in the comment tag for the registered client.
Click the Apply Changes button to register the
client to new configuration setting.
Click the Reset button to abort change and recover
the previous configuration setting.
It shows the registered clients that are allowed to
Control List
Delete Selected
Delete All
Reset
link to this WLAN Broadband Router.
Click to delete the selected clients that will be
access right removed from this WLAN Broadband
Router.
Click to delete all the registered clients from the
access allowed list.
Click the Reset button to abort change and recover
the previous configuration setting.
1.2.8WDS Settings
Wireless Distribution System uses wireless media to communicate with
other APs, like the Ethernet does. To do this, you must set these APs in
the same channel and set MAC address of other AP that you want to
communicate with in the table and then enable the WDS.
Screen snapshot – WDS Setup
Item
Enable WDS
MAC Address
Comment
Apply Changes
Reset
Description
Click the check box to enable wireless distribution
system. Refer to 4.21 What is Wireless
Distribution System (WDS)?
Fill in the MAC address of AP to register the
wireless distribution system access capability.
Fill in the comment tag for the registered AP.
Click the Apply Changes button to register the AP
to new configuration setting.
Click the Reset button to abort change and recover
the previous configuration setting.
Set Security
Show Statistics
Delete Selected
Delete All
Reset
Click button to configure wireless security like
WEP(64bits), WEP(128bits), WPA(TKIP),
WPA2(AES) or None
It shows the TX, RX packets, rate statistics
Click to delete the selected clients that will be
removed from the wireless distribution system.
Click to delete all the registered APs from the
wireless distribution system allowed list.
Click the Reset button to abort change and recover
the previous configuration setting.
8. WDS Security Setup
Requirement: Set [Wireless]->[Basic
Settings]->[Mode]->AP+WDS
This page is used to configure the wireless security between
APs. Refer to 3.3.6 Wireless Security Setup.
Screen snapshot – WDS Security Setup
9. WDS AP Table
This page is used to show WDS statistics
Screen snapshot – WDS AP Table
Item
MAC Address
Tx Packets
Tx Errors
Rx Packets
Tx Rare (Mbps)
Refresh
Close
Description
It shows the MAC Address within WDS.
It shows the statistic count of sent packets on the
wireless LAN interface.
It shows the statistic count of error sent packets on
the Wireless LAN interface.
It shows the statistic count of received packets on
the wireless LAN interface.
It shows the wireless link rate within WDS.
Click to refresh the statistic counters on the
screen.
Click to close the current window.
1.2.9Site Survey
This page is used to view or configure other APs near yours.
Screen snapshot – Wireless Site Survey
Item
SSID
BSSID
Channel
Type
Encrypt
Signal
Select
Refresh
Connect
Description
It shows the SSID of AP.
It shows BSSID of AP.
It show the current channel of AP occupied.
It show which type AP acts.
It shows the encryption status.
It shows the power level of current AP.
Click to select AP or client you’d like to connect.
Click the Refresh button to re-scan site survey on
the screen.
Click the Connect button to establish connection.
1.2.10LAN Interface Setup
This page is used to configure the parameters for local area network
that connects to the LAN ports of your WLAN Broadband Router.
Here you may change the setting for IP address, subnet mask, DHCP,
etc.
Screen snapshot – LAN Interface Setup
Item
IP Address
Description
Fill in the IP address of LAN interfaces of this
WLAN Access Point.
Subnet Mask
Fill in the subnet mask of LAN interfaces of this
WLAN Access Point.
Default Gateway
Fill in the default gateway for LAN interfaces out
going data packets.
DHCP
Click to select Disabled, Client or Server in
different operation mode of wireless Access Point.
DHCP Client Range Fill in the start IP address and end IP address to
allocate a range of IP addresses; client with DHCP
function set will be assigned an IP address from
the range.
Show Client
Click to open the Active DHCP Client Table
window that shows the active clients with their
assigned IP address, MAC address and time
expired information. [Server mode only]
DNS Server
Manual setup DNS server IP address.
Domain Name
Assign Domain Name and dispatch to DHCP
clients. It is optional field.
802.1d Spanning
Select to enable or disable the IEEE 802.1d
Tree
Spanning Tree function from pull-down menu.
Clone MAC Address Fill in the MAC address that is the MAC address
to be cloned. Refer to 4.24 What is Clone MAC
Address?
Apply Changes
Click the Apply Changes button to complete the
new configuration setting.
Reset
Click the Reset button to abort change and recover
the previous configuration setting.
1.2.11WAN Interface Setup
This page is used to configure the parameters for wide area network
that connects to the WAN port of your WLAN Broadband Router.
Here you may change the access method to Static IP, DHCP, PPPoE
or PPTP by click the item value of WAN Access Type.
10. Static IP
Screen snapshot – WAN Interface Setup – Static IP
Item
Static IP
Description
Click to select Static IP support on WAN
interface. There are IP address, subnet mask and
default gateway settings need to be done.
IP Address
If you select the Static IP support on WAN
interface, fill in the IP address for it.
Subnet Mask
If you select the Static IP support on WAN
interface, fill in the subnet mask for it.
Default Gateway
If you select the Static IP support on WAN
interface, fill in the default gateway for WAN
interface out going data packets.
MTU Size
Fill in the mtu size of MTU Size. The default
value is 1400
DNS 1
Fill in the IP address of Domain Name Server 1.
DNS 2
Fill in the IP address of Domain Name Server 2.
DNS 3
Fill in the IP address of Domain Name Server 3.
Clone MAC Address Fill in the MAC address that is the MAC address
to be cloned. Refer to 4.24 What is Clone MAC
Address?
Enable uPNP
Click the checkbox to enable uPNP function.
Refer to 4.22 What is Universal Plug and Play
(uPNP)?
Enable Web Server Click the checkbox to enable web configuration
Access on WAN
Enable WAN Echo
Reply
Enable IPsec pass
through on VPN
connection
Enable PPTP pass
through on VPN
connection
Enable L2TP pass
through on VPN
connection
Set TTL value
Apply Changes
Reset
from WAN side.
Click the checkbox to enable WAN ICMP
response.
Click the checkbox to enable IPSec packet pass
through
Click the checkbox to enable PPTP packet pass
through
Click the checkbox to enable L2TP packet pass
through
Click to Enable and set Time to Live value.
Click the Apply Changes button to complete the
new configuration setting.
Click the Reset button to abort change and
recover the previous configuration setting.
11. DHCP Client
Screen snapshot – WAN Interface Setup – DHCP Client
Item
DHCP Client
Host Name
Description
Click to select DHCP support on WAN interface
for IP address assigned automatically from a
DHCP server.
Fill in the host name of Host Name. The default
value is empty
MTU Size
Fill in the mtu size of MTU Size. The default
value is 1400
Attain DNS
Click to select getting DNS address for DHCP
Automatically
support. Please select Set DNS Manually if the
DHCP support is selected.
Set DNS Manually
Click to select getting DNS address for DHCP
support.
DNS 1
Fill in the IP address of Domain Name Server 1.
DNS 2
Fill in the IP address of Domain Name Server 2.
DNS 3
Fill in the IP address of Domain Name Server 3.
Clone MAC Address Fill in the MAC address that is the MAC address
to be cloned. Refer to 4.24 What is Clone MAC
Address?
Enable uPNP
Click the checkbox to enable uPNP function.
Refer to 4.22 What is Universal Plug and Play
(uPNP)?
Enable Web Server
Click the checkbox to enable web configuration
Access on WAN
from WAN side.
Enable WAN Echo
Click the checkbox to enable WAN ICMP
Reply
response.
Set TTL value
Click to Enable and set Time to Live value.
Apply Changes
Click the Apply Changes button to complete the
new configuration setting.
Reset
Click the Reset button to abort change and
recover the previous configuration setting.
12. PPPoE
Screen snapshot – WAN Interface Setup – PPPoE
Item
PPPoE
User Name
Password
Service Name
Connection Type
Description
Click to select PPPoE support on WAN interface.
There are user name, password, connection type
and idle time settings need to be done.
If you select the PPPoE support on WAN
interface, fill in the user name and password to
login the PPPoE server.
If you select the PPPoE support on WAN
interface, fill in the user name and password to
login the PPPoE server.
Fill in the service name of Service Name. The
default value is empty.
Select the connection type from pull-down menu.
There are Continuous, Connect on Demand and
Manual three types to select.
Continuous connection type means to setup the
connection through PPPoE protocol whenever
this WLAN Broadband Router is powered on.
Connect on Demand connection type means to
setup the connection through PPPoE protocol
whenever you send the data packets out through
the WAN interface; there are a watchdog
implemented to close the PPPoE connection
while there are no data sent out longer than the
idle time set.
Manual connection type means to setup the
connection through the PPPoE protocol by
clicking the Connect button manually, and
clicking the Disconnect button manually.
Idle Time
If you select the PPPoE and Connect on
Demand connection type, fill in the idle time for
auto-disconnect function. Value can be between 1
and 1000 minutes.
MTU Size
Fill in the mtu size of MTU Size. The default
value is 1400. Refer to 4.23 What is Maximum
Transmission Unit (MTU) Size?
Attain DNS
Click to select getting DNS address for PPPoE
Automatically
support. Please select Set DNS Manually if the
PPPoE support is selected.
Set DNS Manually
Click to select getting DNS address for Static IP
support.
DNS 1
Fill in the IP address of Domain Name Server 1.
DNS 2
Fill in the IP address of Domain Name Server 2.
DNS 3
Fill in the IP address of Domain Name Server 3.
Clone MAC Address Fill in the MAC address that is the MAC address
to be cloned. Refer to 4.24 What is Clone MAC
Address?
Enable uPNP
Click the checkbox to enable uPNP function.
Refer to 4.22 What is Universal Plug and Play
(uPNP)?
Enable Web Server Click the checkbox to enable web configuration
Access on WAN
from WAN side.
Enable WAN Echo
Click the checkbox to enable WAN ICMP
Reply
response.
Set TTL value
Click to Enable and set Time to Live value.
Apply Changes
Click the Apply Changes button to complete the
new configuration setting.
Reset
Click the Reset button to abort change and
recover the previous configuration setting.
13. PPTP
Screen snapshot – WAN Interface Setup – PPTP
Item
Description
PPTP
Allow user to make a tunnel with remote site
directly to secure the data transmission among the
connection. User can use embedded PPTP client
supported by this router to make a VPN
connection.
IP Address
If you select the PPTP support on WAN interface,
fill in the IP address for it.
Subnet Mask
If you select the PPTP support on WAN interface,
fill in the subnet mask for it.
Server IP Address
Enter the IP address of the PPTP Server.
User Name
If you select the PPTP support on WAN interface,
fill in the user name and password to login the
PPTP server.
Password
f you select the PPTP support on WAN interface,
fill in the user name and password to login the
PPTP server.
MTU Size
Fill in the mtu size of MTU Size. The default
value is 1400. Refer to 4.23 What is Maximum
Transmission Unit (MTU) Size?
Request MPPE
Click the checkbox to enable request MPPE
Encryption
Attain DNS
Automatically
encryption.
Click to select getting DNS address for PPTP
support. Please select Set DNS Manually if the
PPTP support is selected.
Set DNS Manually
Click to select getting DNS address for PPTP
support.
DNS 1
Fill in the IP address of Domain Name Server 1.
DNS 2
Fill in the IP address of Domain Name Server 2.
DNS 3
Fill in the IP address of Domain Name Server 3.
Clone MAC Address Fill in the MAC address that is the MAC address
to be cloned. Refer to 4.24 What is Clone MAC
Address?
Enable uPNP
Click the checkbox to enable uPNP function.
Refer to 4.22 What is Universal Plug and Play
(uPNP)?
Enable Web Server
Click the checkbox to enable web configuration
Access on WAN
from WAN side.
Enable WAN Echo
Click the checkbox to enable WAN ICMP
Reply
response.
Set TTL value
Click to Enable and set Time to Live value.
Apply Changes
Click the Apply Changes button to complete the
new configuration setting.
Reset
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.12Firewall - Port Filtering
Entries in this table are used to restrict certain types of data packets
from your local network to Internet through the Gateway. Use of such
filters can be helpful in securing or restricting your local network.
Screen snapshot – Firewall - Port Filtering
Item
Enable Port Filtering
Port Range
Protocol
Comments
Apply Changes
Reset
Delete Selected
Delete All
Reset
Description
Click to enable the port filtering security function.
To restrict data transmission from the local
network on certain ports, fill in the range of startport and end-port, and the protocol, also put your
comments on it.
The Protocol can be TCP, UDP or Both.
Comments let you know about whys to restrict
data from the ports.
Click the Apply Changes button to register the
ports to port filtering list.
Click the Reset button to abort change and
recover the previous configuration setting.
Click to delete the selected port range that will be
removed from the port-filtering list.
Click to delete all the registered entries from the
port-filtering list.
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.13Firewall - IP Filtering
Entries in this table are used to restrict certain types of data packets
from your local network to Internet through the Gateway. Use of such
filters can be helpful in securing or restricting your local network.
Screen snapshot – Firewall - IP Filtering
Item
Enable IP Filtering
Local IP Address
Description
Click to enable the IP filtering security function.
To restrict data transmission from local network
Protocol
Comments
Apply Changes
Reset
Delete Selected
Delete All
Reset
on certain IP addresses, fill in the IP address and
the protocol, also put your comments on it.
The Protocol can be TCP, UDP or Both.
Comments let you know about whys to restrict
data from the IP address.
Click the Apply Changes button to register the IP
address to IP filtering list.
Click the Reset button to abort change and
recover the previous configuration setting.
Click to delete the selected IP address that will be
removed from the IP-filtering list.
Click to delete all the registered entries from the
IP-filtering list.
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.14Firewall - MAC Filtering
Entries in this table are used to restrict certain types of data packets
from your local network to Internet through the Gateway. Use of such
filters can be helpful in securing or restricting your local network.
Screen snapshot – Firewall - MAC Filtering
Item
Enable MAC
Filtering
MAC Address
Comments
Description
Click to enable the MAC filtering security
function.
To restrict data transmission from local network
on certain MAC addresses, fill in the MAC
address and your comments on it.
Comments let you know about whys to restrict
data from the MAC address.
Apply Changes
Reset
Delete Selected
Delete All
Reset
Click the Apply Changes button to register the
MAC address to MAC filtering list.
Click the Reset button to abort change and
recover the previous configuration setting.
Click to delete the selected MAC address that will
be removed from the MAC-filtering list.
Click to delete all the registered entries from the
MAC-filtering list.
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.15Firewall - Port Forwarding
Entries in this table allow you to automatically redirect common
network services to a specific machine behind the NAT firewall.
These settings are only necessary if you wish to host some sort of
server like a web server or mail server on the private local network
behind your Gateway's NAT firewall.
Screen snapshot – Firewall - Port Forwarding
Item
Enable Port
Forwarding
IP Address
Protocol
Port Range
Comment
Description
Click to enable the Port Forwarding security
function.
To forward data packets coming from WAN to a
specific IP address that hosted in local network
behind the NAT firewall, fill in the IP address,
protocol, port range and your comments.
The Protocol can be TCP, UDP or Both.
The Port Range for data transmission.
Comments let you know about whys to allow data
Apply Changes
Reset
Delete Selected
Delete All
Reset
packets forward to the IP address and port
number.
Click the Apply Changes button to register the IP
address and port number to Port forwarding list.
Click the Reset button to abort change and
recover the previous configuration setting.
Click to delete the selected IP address and port
number that will be removed from the portforwarding list.
Click to delete all the registered entries from the
port-forwarding list.
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.16Firewall – URL Filtering
URL Filtering is used to restrict users to access specific websites in
internet.
Screen snapshot – Firewall – URL Filtering
Item
Enable URL
Filtering
URL Address
Description
Click to enable the URL Filtering function.
Apply Changes
Reset
Click the Apply Changes button to save settings.
Click the Reset button to abort change and recover
Add one URL address.
Delete Selected
Delete All
Reset
the previous configuration setting.
Click to delete the selected URL address that will
be removed from the URL Filtering list.
Click to delete all the registered entries from the
URL Filtering list.
Click the Reset button to abort change and recover
the previous configuration setting.
1.2.17Firewall - DMZ
A Demilitarized Zone is used to provide Internet services without
sacrificing unauthorized access to its local private network. Typically,
the DMZ host contains devices accessible to Internet traffic, such as
Web (HTTP) servers, FTP servers, SMTP (e-mail) servers and DNS
servers.
Screen snapshot – Firewall - DMZ
Item
Enable DMZ
DMZ Host IP
Address
Description
Click to enable the DMZ function.
To support DMZ in your firewall design, fill in the
IP address of DMZ host that can be access from
the WAN interface.
Apply Changes
Click the Apply Changes button to register the IP
address of DMZ host.
Click the Reset button to abort change and recover
the previous configuration setting.
Reset
1.2.18VPN Setting
This page is used to show VPN connection table, configure IPSEC
VPN, NAT Traversal, Generate RSA Key, Show RSA Public Key.
Screen snapshot – VPN Setup
Item
Enable IPSEC VPN
Enable NAT
Traversal
Generate RSA Key
Show RSA Public
Key
Apply Changes
Current VPN
Connection Table
Edit
Delete
Refresh
Description
Click to enable IPSEC VPN function. Refer to
4.27 What is VPN? and 4.28 What is IPSEC?
Click to enable NAT Traversal function.
Click to generate RSA key.
Click to show RSA public key that we generate.
Click the Apply Changes button to enable IPSEC
VPN, NAT Traversal settings.
It shows current WAN interface information and
VPN connection table.
Click to enter the current VPN tunnel
configuration page.
Click to delete the current VPN tunnel that radio
button stay.
Click to refresh the current VPN connection table.
14. VPN Setup - Edit Tunnel
Screen snapshot – VPN Setup-Edit-1
Item
Enable Tunnel #
Connection Name
Auth Type
Local Site
Local IP
Address/Network
Local Subnet Mask
Remote Site
Description
Click to enable the IPSEC VPN current tunnel.
Assign the connection name tag.
Click to select PSK or RSA.
Click to select Single Address or Subnet
Address VPN connection.
Fill in IP address or subnet address depends on
which Local Site option you choose.
Fill in the local subnet mask.
Click to select Single Address, Subnet Address,
Any Address or NAT-T Any Address VPN
remote connection.
Fill in remote gateway IP address
Remote Secure
Gateway
Remote IP
Address/Network
Fill in IP address or subnet address depends on
Remote Subnet Mask which Remote Site option you choose.
Fill in remote subnet mask
Local/Peer ID
Define IKE exchange information type
Local ID Type
Click to select IP, DNS or E-mail as local
Local ID
exchange type
Remote ID Type
Fill in local ID except IP selected
Click to select IP, DNS or E-mail as remote
Remote ID
exchange type
Fill in remote ID except IP selected
Screen snapshot – VPN Setup-Edit-2
Item
Key Management
Advanced
Connection Type
Connect
Disconnect
ESP
PreShared Key
Remote RSA Key
Status
SPI
Encryption Key
Authentication Key
Apply Change
Reset
Refresh
Back
Description
Click to select IKE or Manual mode.
Click Advanced button to configure more IKE
settings.
Click to select Initiator or Responder mode.
Click to connect manually. [Responder mode
only]
Click to disconnect manually. [Responder mode
only].
Click to configure 3DES, AES128 or NULL
encryption.
Click to configure MD5 or SHA1 authentication.
Fill in the key value. [IKE mode only]
Fill in the remote gateway RSA key. [IKE mode
only]
It shows connection status. [IKE mode only]
Fill in Security Parameter Index value. [Manual
mode only]
Fill in encryption key. [Manual mode only]
Fill in authentication key. [Manual mode only]
Click the Apply Changes button to save current
tunnel settings.
Click the Reset button to abort change and
recover the previous configuration setting.
It shows the current connection status. [Manual
mode only]
It returns back to VPN Setup page.
15. Advanced IKE Setup
Screen snapshot – Advanced VPN Settings for IKE
Item
Phase 1
Negotiation Mode
Encryption Algorithm
Authentication
Algorithm
Key Group
Description
Main mode.
Click to select 3DES or AES128 encryption.
Click to select MD5 or SHA1 authentication.
Click to select DH1(modp768), DH2(modp1024)
or DH5(modp1536) key group. Default value is
DH2
Fill in the key life time value by seconds.
Key Life Time
Phase 2
Active Protocol
ESP.
Encryption Algorithm Click to select 3DES, AES128 or NULL
encryption.
Authentication
Algorithm
Key Life Time
Encapsulation
Perfect Forward
Secrecy (PFS)
Ok
Cancel
Click to select MD5 or SHA1 authentication.
Fill in the key life time value by seconds.
Tunnel mode.
Click to select ON or NONE.
Click the Ok button to save current tunnel
settings.
Click the Cancel button to close current window
without any changes.
1.2.19Management - Statistics
This page shows the packet counters for transmission and reception
regarding to wireless, Ethernet LAN and Ethernet WAN networks.
Screen snapshot – Management - Statistics
Item
Wireless LAN
Sent Packets
Wireless LAN
Received Packets
Ethernet LAN
Sent Packets
Ethernet LAN
Received Packets
Ethernet WAN
Sent Packets
Ethernet WAN
Received Packets
Refresh
Description
It shows the statistic count of sent packets on the
wireless LAN interface.
It shows the statistic count of received packets on
the wireless LAN interface.
It shows the statistic count of sent packets on the
Ethernet LAN interface.
It shows the statistic count of received packets on
the Ethernet LAN interface.
It shows the statistic count of sent packets on the
Ethernet WAN interface.
It shows the statistic count of received packets on
the Ethernet WAN interface.
Click the refresh the statistic counters on the
screen.
1.2.20Management - DDNS
This page is used to configure Dynamic DNS service to have DNS
with dynamic IP address.
Screen snapshot – Management – DDNS
Item
Enable DDNS
Service Provider
Domain Name
User Name/Email
Password/Key
Apply Change
Reset
Description
Click the checkbox to enable DDNS service.
Refer to 4.25 What is DDNS?
Click the drop down menu to pickup the right
provider.
To configure the Domain Name.
Configure User Name, Email.
Configure Password, Key.
Click the Apply Changes button to save the
enable DDNS service.
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.21Management - Time Zone Setting
This page is used to configure NTP client to get current time.
Screen snapshot – Management – Time Zone Settings
Item
Current Time
Time Zone Select
Enable NTP client
update
NTP Server
Apply Change
Reset
Refresh
Description
It shows the current time.
Click the time zone in your country.
Click the checkbox to enable NTP client update.
Refer to 4.26 What is NTP Client?
Click select default or input NTP server IP
address.
Click the Apply Changes button to save and
enable NTP client service.
Click the Reset button to abort change and recover
the previous configuration setting.
Click the refresh the current time shown on the
screen.
1.2.22Management – Denial-of-Service
This page is used to enable and setup protection to prevent attack by
hacker’s program. It provides more security for users.
Screen snapshot – Management – Denial-of-Service
Item
Enable DoS
Prevention
Whole System
Flood / Per-Source IP
Flood…
Select ALL
Clear ALL
Apply Changes
Description
Click the checkbox to enable DoS prevention.
Enable and setup prevention in details.
Click the checkbox to enable all prevention items.
Click the checkbox to disable all prevention
items.
Click the Apply Changes button to save above
settings.
1.2.23Management - Log
This page is used to configure the remote log server and shown the
current log.
Screen snapshot – Management – Log
Item
Enable Log
System all
Wirelessy
DoS
Enable Remote Log
Log Server IP
Address
Apply Changes
Refresh
Clear
Description
Click the checkbox to enable log.
Show all log of wireless broadband router
Only show wireless log
Only show Denial-of-Service log
Click the checkbox to enable remote log service.
Input the remote log IP address
Click the Apply Changes button to save above
settings.
Click the refresh the log shown on the screen.
Clear log display screen
1.2.24Management - Upgrade Firmware
This page allows you upgrade the Access Point firmware to new
version. Please note, do not power off the device during the upload
because it may crash the system.
Screen snapshot – Management - Upgrade Firmware
Item
Select File
Upload
Reset
Description
Click the Browse button to select the new version
of web firmware image file.
Click the Upload button to update the selected
web firmware image to the WLAN Broadband
Router.
Click the Reset button to abort change and recover
the previous configuration setting.
1.2.25Management Save/ Reload Settings
This page allows you save current settings to a file or reload the
settings from the file that was saved previously. Besides, you could
reset the current configuration to factory default.
Screen snapshot – Management - Save/Reload Settings
Item
Description
Save Settings to File Click the Save button to download the
configuration parameters to your personal
computer.
Load Settings from Click the Browse button to select the
File
configuration files then click the Upload button to
update the selected configuration to the WLAN
Broadband Router.
Reset Settings to
Click the Reset button to reset the configuration
Default
parameter to factory defaults.
1.2.26Management - Password Setup
This page is used to set the account to access the web server of
Access Point. Empty user name and password will disable the
protection.
+
Screen snapshot – Management - Password Setup
Item
User Name
Description
Fill in the user name for web management login
control.
New Password
Fill in the password for web management login
control.
Confirmed Password Because the password input is invisible, so please
fill in the password again for confirmation
purpose.
Apply Changes
Clear the User Name and Password fields to
empty, means to apply no web management login
control.
Click the Apply Changes button to complete the
new configuration setting.
Reset
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.27Management - WatchDog
This page is used to do watchdog function using ping command. User
set IP address, interval and ping fail count conditions to decide
whether router reboots or not.
Screen snapshot – Management – WatchDog Settiing
Item
Enable WatchDog
WatchDog IP
Address
Ping Interval
Ping Fail to reboot
Count
Apply Changes
Reset
Description
Click to enable watchdog.
IP address that is referred.
Fill in the value by seconds.
Fill in the value that is the threshold to reboot
router when ping fails.
Click the Apply Changes button to complete the
new configuration setting.
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.28Management - Quality of Service
This page is used to do bandwidth control by ip address. User sets total
and undefined bandwidth first. Then set bandwidth by range of ip
addresses.
Screen snapshot – Management – Qaulity of Service
Item
Enable QoS
ISP Bandwidth
Download
Upload
Description
Click to enable QoS.
Fill in the value that is the download stream from
ISP by KB/s.
Fill in the value that is the upload stream from ISP
by KB/s.
Undef IP Bandwidth
Download
Define the download bandwidth that is not
defined.
Upload
Define the upload bandwidth that is not defined.
Apply Changes
Click the Apply Changes button to complete the
new configuration setting.
Reset
Click the Reset button to abort change and
recover the previous configuration setting.
Item
Description
Bandwidth Control
IP Address Range
Set start and end ip address.
Guarantee Bandwidth
Download
Fill in the value by KB/s.
Upload
Fill in the value by KB/s.
Piority
Apply Changes
Reset
Delete Selected
Delete All
Reset
Click to pick High, Medium or Low
Click the Apply Changes button to complete the
new configuration setting. It is added into
Current Bandwidth Control Table.
Click the Reset button to abort change and
recover the previous configuration setting.
Click to delete the selected ip addresses that will
be removed from the Current Bandwidth
Control Table.
Click to delete all the registered entries from the
ip addresses Current Bandwidth Control Table.
Click the Reset button to abort change and
recover the previous configuration setting.
1.2.29Logout
This page is used to logout web management page. This item will be
activated next time you login after you define user account and
password.
Screen snapshot – Logout
Screen snapshot – Logout - OK
Item
Apply Change
Description
Click the Apply Change button, Then click OK
button to logout.
Fabricante: A. Kamide - Inform€tica-ME
Rua Jos• Bonif€cio, 799 Sl 03 - Centro
Cep 87.360-000 - Goioer‚ - PR
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising