8949MDA-CFR PAL/NTSC Monitoring Distribution Amplifier 17 - AV-iQ

8949MDA-CFR PAL/NTSC Monitoring Distribution Amplifier 17 - AV-iQ
8949MDA-CFR PAL/NTSC Monitoring Distribution Amplifier
Key Features
• Reclocked distribution of HD-SDI signals
for reconstructed input fan-out
• PAL/NTSC monitoring output
• Distributes both HD-SDI and SD-SDI with
automatic format detection for flexible
future-proof system architectures
• Provides SD monitoring output whether
input is SD or HD
• Very high-density solution
• Accepts optional fiber transmitter to
provide optical, HD-SDI, and PAL/NTSC
monitoring outputs for combined local/
remote systems
• Configurable as fiber receiver with four
HD-SDI outputs and PAL/NTSC monitoring
Applications
• Where an PAL/NTSC monitoring feed is
required
• HD-SDI distribution alongside monitoring
in PAL or NTSC
• Rate-agile systems requiring distribution
and a consistent composite monitoring
feed
• A fiber receiver with composite monitoring
• A fiber transmitter with local HD and
composite monitoring feeds
The 8949MDA-CFR is a monitoring distribution
amplifier with PAL/NTSC monitoring outputs.
This module is ideal for low-cost monitoring of
HD-SDI signals. The 8949MDA-CFR provides four
monitoring outputs and four reclocked outputs
and can be used to distribute either HD-SDI
or SD-SDI making it ideal for mixed format
applications or installations where an upgrade is
planned.
Thanks to its fiber-ready architecture the
8949MDA-CFR can be configured to support up
to two fiber connections in addition to its eight
coax outputs. Applications include use as an
HD-SDI fiber transmitter with additional monitoring
and reclocked coax feeds.
Parameters can be adjusted directly from
the module itself or via standard HTML Web
browsers or via the Newton control panel (when
installed in network equipped frames). In addition,
NetConfig and NetCentral can be used for remote
configuration and signal health monitoring.
Please note that the 8949MDA-CFR provides
16:9 anamorphic monitoring outputs for HD
signals and 4:3 outputs for SD inputs. The
8949MDA-SFR should
be selected if an SDI
HD/SD
monitoring output is
SDI In
required. This is a
monitoring device so,
in order to provide
the fastest possible
Only one fiber
option may be
conversion, the module
selected
does not perform
Fiber RX
de-interlacing and
Fiber RX
consequently it has
HD/SD
an extremely short
Optical In
processing delay of
Fiber RX
0.97 ms.
Supported Frame Types
Electrical Length (Delay)
0.97 ms
Power Rating
Conversion
HD/SD-SDI:
•Input equalization: up to 125m HD-SDI,
up to 330m SD-SDI (Belden1694A)
•Return loss: >15 dB 0.004 to 1.5 GHz
Optical: Single-mode (optional)
Formats supported: 1080i @ 59.94, 50,
720p @ 59.94, 50, 480i @ 59.94 (NTSC)
576i @ 50 (PAL-B)
Outputs
J1
J2
HD/SD
SDI Out
J3
J4
HD/SD
SDI Out
J5
J6
PAL/NTSC
Out
J7
J8
PAL/NTSC
Out
HD/SD
SDI Out
PAL/NTSC
Out
PAL/NTSC
Out
Fiber I/O
Connector
J9
HD/SD
SDI In
FIBER
4X HD/
SD-SDI
Out
Downconverter
4X
PAL/NTSC
Out
Encoder
Fiber TX
Option
Option
Fiber TX
HD/SD
Optical Out
Fiber TX
Option
Ordering Information
GeckoFlex frame
Inputs
HD/SD
SDI Out
Equalizer and
Re-clocker
Specifications
8.5 Watts – single slot
8900WFR-R
9 bits representation
Type: Field-based high speed monitoring to drive 16:9
monitors
Input formats: 59.94 Hz, 1080i @ 59.94 Hz,
720p @ 59.94 Hz, 480i @ 59.94 Hz
•To output format: 480i @ 59.94 Hz
Input formats: 50 Hz, 1080i @ 50 Hz, 720p @
50 Hz, 576i @ 50 Hz
•To output format: 576i @ 50 Hz
Manual input selection: Coax In, fiber 1, fiber 2 (with
optional fiber input)
HD/SD-SDI: Four outputs
•Return loss: >15 dB, 5 to 270 MHz;
>10 dB to 1.5 GHz
•Signal level: SDI 800 mVp-p ±10%
•Output jitter: for input with <0.1 UI jitter, the output
jitter complies with the SMPTE 259M & 292M
standards
Input format selection: Automatic/manual
Optical: Single-mode (optional)
Analog video: Four outputs (75Ω)
•Formats: SMPTE 170M (NTSC), CCIR624 (PAL-B)
•Return loss: > 40 dB to 10 MHz
•Signal level: SDI 800 mVp-p ±10%
•Output jitter: for input with <0.1 UI
Newton support: Yes
Control And Monitoring
SNMP: Yes
Web page configuration: Yes
Local configuration: Yes
This module can be mounted in a GeckoFlex
frame but not in other 8900 series frames
including Gecko-A or Gecko-V frames.
8949MDA-CFR
HD/SD monitoring distribution amplifier PAL/NTSC
output – fiber-ready front and rear module set.
For SD-SDI out monitoring see the 8949MDA-SFR
1310NM-DRL
Dual input fiber receiver. For one-signal-per-fiber and
CWDM fiber systems
1310NM-DTL
Dual output fiber transmitter. For one-signal-per-fiber
systems
1310NM-TRL
Fiber transceiver. For one-signal-per-fiber systems
Please note that the 8949MDA-CFR provides 16:9 anamorphic
monitoring outputs for HD signals and 4:3 outputs for SD inputs.
You should use the 8949MDA-SFR for SDI output monitoring.
To provide the fastest-possible conversion, this module does not
perform de-interlacing and consequently it has an extremely short
processing delay of 0.97 ms.
NetConfig support: Yes
NetCentral support: Yes
For detailed specifications, installation, and setup
instructions see:
www.grassvalley.com/docs/modular
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising