PL3000 Series Hard Disk/SSD Unit Installation Guide

PL3000 Series Hard Disk/SSD Unit Installation Guide
Safety Cautions
PL3000 Series
Hard Disk/SSD Unit
Installation Guide
• Do not attempt to modify or open the
HDD/SSD unit, since it can cause a
shock or fire.
• When installing the HDD/SSD unit, be
sure to read this guide "Installation"
section's information completely to
insure that the unit is correctly
installed.
This instruction guide covers the following
products.
• APL3000-HD60
• APL3000-HD250
• APL3000-SD16
To Prevent Accidents
The APL3000-HD60, The APL3000-HD250
is the hard disk unit for Pro-face's PL3000
series (hereafter referred as the "HDD unit").
• To prevent from a unit malfunction, be
sure to check that the PL unit's power is
disconnected before installing the unit.
• Since the HDD/SSD unit is a precision
instrument, be sure it is neither hit by nor
pressed strongly against another object.
After unpacking, be sure the unit is not
dropped or jolted during installation. Also,
a PL unit built in to a larger unit (i.e. operation panel) should be removed and packed
separately prior to shipping.
• Be sure water, liquids or metal particles are
not allowed to enter the HDD/SSD unit.
Any of these may cause either a breakdown or an electrical shock.
• Do not place or store this unit in a location
where there is direct sunlight, excessive
heat, dust or vibration.
• Do not store or operate this unit near chemicals, or where there are chemical fumes.
• Do not allow anyone other than Pro-face’s
own service staff to perform maintenance
or adjustments to this unit.
• Do not move or shift the PL unit while the
HDD/SSD unit is installed and the PL
unit's power is ON.
• Do not use the HDD/SSD unit in locations
where corrosive gasses are present, since
they can lead to a hard disk breakdown.
• To prevent the data damage, be sure to shut
down the PL unit’s OS according to the
correct procedure before turning OFF the
main power.
The APL3000-SD16 is SSD unit for Proface's PL3000 series.
This HDD/SSD unit has built-in recording
device to be used for loading the HDD slot of
the PL.
Applicable model: PL3000 series (hereafter
referred as the "PL")
• APL3000-HD250 cannot be used for Windows® 2000. Use APL3000-HD60 for
Windows® 2000.
About the Manual
For the detailed information on PL series,
refer to the following manuals.
• PL3000 Series Hardware Manual
Manuals for PL3000 series can be
downloaded from Pro-face Home Page.
URL
http://www.pro-face.com/
1
• To prevent memory leaks, restart the OS
periodically.
• The hard disk has the lifetime. To use it
longer by steady operation, read the
attached “Instructions for Using the Hard
Disk” carefully.
• In order to extend the lifetime of the hard
disk, Pro-face recommends you set the
Windows® [Control panel]-[Power Management option]-[Turn off hard disks]
selection to turn the hard disk off when the
unit is not being operated. A setting of 5
minutes is recommended.
Hardware Specifications
 HDD Unit
Features
Capacity
APL3000-HD60: 60GB
APL3000-HD250: 250GB
Average
Seek Time
13msec (TYP)
At Startup: 4.5W or less
Power
Consumption Read/Write: 1.5W (TYP)
During wait: 0.2W (TYP)
Interface
Serial ATA Rev.1.0a
5 years, or 30,000
Operation
operating hours,
Lifetime
whichever comes first
Unit Disposal
• When this HDD/SSD unit is disposed of, it
should be done so according to your country’s regulations for similar types of industrial wastes.
Weight
Package Contents
Approx. 800g
• The HDD unit's lifetime will vary,
depending on the usage conditions
and environment. The above value is
calculated assuming an ambient temperature of 20°C and 732 hours of
operation per month. (HDD access
frequency of 50% or less)
(1) HDD Unit (1)
or SSD Unit main body (1)
Environment
Surrouding
Air
5°C to 50°C
Temperature
Storage
Temperature -20°C to +60°C
10% to 90%RH
Ambient
(no condensation, wet bulb
Humidity
temperature: 29°C or less)
(2) Installation Guide (1) (This Guide)
(3) Instructions for Using the Hard Disk (1)
(HDD Unit Only)
Storage
Humidity
Pro-face has taken the utmost care to ensure
the quality of this product when it was
shipped, however, should, for any reason,
problems or damage have occurred during
shipping, please contact your Pro-face
representative immediately for service.
Noise
Immunity
10% to 90%RH
(no condensation, wet bulb
temperature: 39°C or less)
Noise voltage: 1,500Vp-p
Pulse width:
50ns, 500ns, 1µs
(via Noise Simulator)
Electrostatic
Discharge
6kV
Immunity
When operating:
10Hz to 57Hz:
Vibration
single-amplitude 0.075mm
Resistance 57Hz to 150Hz: 9.8m/s2
X,Y,Z directions: 10 cycles
(for 80 minutes)
• This HDD/SSD unit has a finite usage
lifetime. Therefore, be sure to back up
all HDD/SSD data periodically and/or
prepare a backup HDD/SSD unit.
2
Concussion
Resistance
Environment
When shipping:
3,920m/s2
(1ms, Half-sine shock
pluse)
Surrounding
Air
Temperature
Storage
Temperature
Ambient
Humidity
Storage
Humidity
• Using the HDD unit in an environment
that is excessively hot and/or humid
will shorten the disk’s usage lifetime. A
wet bulb temperature of 29°C or less
is recommended. This is equivalent to
the following data.
Temperature
Humidity
Noise
Immunity
at 35°C
at 40°C
no higher
no higher
than 64%RH than 44%RH
-20°C to +60°C
10% to 90% RH
(no condensation)
10% to 90% RH
(no condensation)
Noise voltage: 1,500Vp-p
Pulse width: 50ns, 500ns, 1µs
(via Noise Simulator)
Electrostatic
Discharge
6kV
Immunity
Conforms to JIS B 3502,
IEC/EN61131-2
5Hz to 9Hz
single-amplitude 3.5mm
Vibration
Resistance 9Hz to 150Hz
Constant acceleration
9.8m/s2
X,Y,Z directions:10 cycles
(for 100 minutes)
 SSD Unit
Features
Capacity
Power
Consumption
Interface
Weight
0°C to 50°C
16GB
2.5W (MAX.)
Serial ATA Rev.1.0a
Approx. 500g
• The SSD unit has a limited number of writes. Exceeding the guaranteed number of
writes could make it impossible to read and write data, or systems may become
unstable resulting in malfunctions.
• You can calculate the expected lifetime of the SSD unit based on the number of
writes.
SSD memory capacity: 15,631 MB
Guaranteed number of writes: 1 hundred thousand
The expected lifetime when writing 512 MB of data once per minute is approximately
6 years.
Depending on the system and software, data writes may actually be run several times
even when only one write command is made. This can lead to actual lifetimes significantly different from expected lifetimes.
In order to make more accurate lifetime predictions, please use Pro-face's System
Monitor, which is included with the PL unit.
3
(3) Fix the HDD/SSD unit with the two
screws. The torgue should be 0.2 to 0.3
N·m.
Installation
• Since the HDD/SSD unit is a precision
instrument that has a low resistance to
shocks, be sure it is neither hit by nor
pressed strongly against another
object when installing it.
• The electric power may be supplied to
the PL unit even when the screen
blacks out (such as the standby
mode). Be sure to confirm that the
power supply switch on the rear side
of the PL unit is OFF.
• To prevent from a unit malfunction, be
sure to check that the PL unit's power is
disconnected before installing the unit.
Inquiry
Do you have any questions or
commnets about this product?
Please access our site anytime you
need help with a solution.
http://www.pro-face.com/otasuke/
(1) Unscrew the screws (2) of the HDD slot
and remove the cover.
Note
HDD slot 1
Please be aware that Digital Electronics Corporation shall not be held liable by the user
for any damages, losses, or third party claims
arising from the uses of this product.
HDD slot 0
(2) Insert the HDD/SSD unit slowly along
the guide rail while holding the cover of
the HDD unit.
Insert the HDD/SSD unit all the way in
the HDD slot.
Digital Electronics Corporation
Schneider Electric Osaka Building
4-4-9 Kitahama,
Chuo-ku, Osaka 541-0041
JAPAN
http://www.pro-face.com/
Copyright © 2015.2 Digital Electronics
Corporation. All Rights Reserved.
HDD/SSD unit
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising