RF wireless LED remote controller - PL-1

RF wireless LED remote controller - PL-1
RF wireless LED remote controller
Brief introduction of buttons
Model:SR-2819S with SR-1009Fxx
Indicator: indicate the state of
remote control
W
White channel: the 4th channel
Color wheel
4 zones: each zone can save
3 color or modes
Brightness: dim up
Brightness: dim down
ON/OFF of all zones
W+
Running button/Speed button
S1
Save button
Four zones/areas
Press-button RGB+W controller
Receivers work with WIFI-RF converter to be controlled by smart phone
S2
ww nw and cw mixed by RGB
S3
Wiring diagram
1)Receiver Connection Diagram for Single Unit
Power Supply
12-36VDC
110V-230VAC
L
SR-2819S RGBW remote controller has 4 different zones. It can get Red/ Green/ Blue/ White color directly. The
N
Product introduction
remote controller can save up to 3 colors or 3 modes into corresponding buttons (S1,S2,S3) for each zone.
1
You can choose any color through color wheel. you can set the system as RGB 3-channeloutput, or RGBW 42
SR-1009FA
LED CONTROLLER
white
Parameter
3
Learning Key
4
channel output.
Remote
Part No.
SR-2819S
Operation Voltage
3.6VDC
Operation
Frequency
DIMENSIONS
ø/h (mm)
Remarks
434MHz/868MHz
48x140x16
load 3pcs 7 AAA (1.5V)
batteries
2)Receiver Connection Diagram for Multiple Units
N
Power Supply
12-36VDC
Iuput Voltage
Current
Output
Remarks
12-36VDC
4x5A
4x(60-180)W
Constant voltage
1
Part No.
SR-1009FA
110V-230VAC
L
Receiver
Constant voltage
4x(4.2-12.6)W
Constant current
SR-1009FA7
12-36VDC
4x700mA
4x(8.4-25.2)W
Constant current
SR-1009FA
Learning Key
2
4x(96-288)W
4x350mA
LED CONTROLLER
3
4x8A
12-36VDC
1
Product Size
4
12-36VDC
white
SR-1009EA
SR-1009FA3
2
SR-1009FA
white
4
white
4
3
LED CONTROLLER
1
17.
55.0
Learning Key
120.0
2
SR-1009FA
LED CONTROLLER
3
Learning Key
Note:
One receiver can work with 1-8pcs SR-2819S
One SR-2819S control multiple receivers
The power supply chosen must be 20% higher than the actual load
Operation
Safety & Warnings
Learning (matching)
a. Do wiring according to connection diagram
b. Wake up the remote control by touching ON/OFF button.
c. Press learning button on receiver.
d. Touch any zone button on remote control.
e. Then touch color wheel.
f. Connected LED light will blink to confirm zone designation.
g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
product.
Note 1: To choose a master from slaves by jumper for each zone.
Short circuit for master.
Open circuit for slave.
Each zone only can set one master controller. After a period of time, the master will do synchronization
operation to keep the same color or mode of all slaves in one zone.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6) Please ensure that the cable is secured tightly in the connector
7) For update information please consult your supplier.
Note 2: Each remote control 4 zones (areas) receivers, each area can be learned as many receivers as
we can.
Each receiver maximally can be controlled by 8 different remote controllers.
Warranty Agreement
1) We provide lifelong technical assistance with this product:
Color wheel
Choose zone number
, for example,
and , then touch
zone 1 and 3 will indicate corresponding color as we touched.
, choose the color you want,
Brightness Up & Down Button
Short/Long press button
to dim down brightness of RGB channels, Short/long press
button to dim
up RGB channels.
“W” channel is separated from RGB channels, so we can only long press button to dimming“W” channel.
Running Mould & Speed Button
a. Short press
, mode will run. Press it once, it runs one mode. Press button again, it stops, then press
one more time, it will enter next mode. There are total 10 build-in modes.
b. Long press
when mode is running, Fist long press will speed up the color moving, long press again to
speed down the color moving.
W+ Button
a. RGB channel will mix to three different white: warm white, nature white and cold white by short press
For example: first press---warm white, press again---nature white, third press again—cold white, fourth
press—warm white………………
b. Fast click twice
W+ to switch off RGB channel.
Save and recall button
a. Save color: select zones from
LED lighting flash twice
indicate save successful
b. Save running mold: select zones from
LED lighting flash twice
indicate save successful
select a color from
long press one save button
from S1,S2,S3 for 2-3 second
select a moving mode from
long press one save button from
S1,S2,S3 for 2-3 second
c. Recall: select zone button which we want recall from 1-4, then short press save button S1,S2,S3.
W+
3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The
warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 3-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising