FVT/FVR1031(M)(S)1

FVT/FVR1031(M)(S)1
INSTALLATION AND OPERATION MANUAL
FVT/FVR1031(M)(S)1
10-bit digital video with bi-directional data
(RS232, 422 and RS485 2 & 4 Wire)
Pelco and Panasonic “UP-THE-COAX”
The FVT/FVR1031 transmits 10 bit digital video and full duplex data over one
Singlemode or Multimode fiber. The video supports NTSC, PAL and SECAM CCTV
camera systems. The data supports RS232, RS422 and RS485 (2W & 4W) at data rates
up to 115 Kbps (NRZ). The FVT/FVR1031 series also supports “UP-THE-COAX” control
signals for Pelco and Panasonic cameras with a maximum distance of 1500 feet (590
meters). The product is “Plug-and-Play” with no electrical or optical adjustments.
The FVT/FVR1031 allows the user to choose bi-directional data or up-the-coax data
through a switch on the unit, as described in Figure 6 on Page 3.
Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining equipment
operating status. Figure 4 on Page 3 describes the LED indicators for each light on
the unit.
These units are interchangeable between stand-alone or card mount configurations,
or used with a DIN-rail adapter. See Figure A on Page 4 for installation instructions.
See Figures 1 – 7 for complete installation details.
INS_FVT/FVR1031_REV–
02/05/10
PAGE 1
INSTALLATION AND OPERATION MANUAL
FVT/FVR1031(M)(S)1
FIGURE 1 – FVT/FVR1031 TRANSMITTER AND RECEIVER
MULTIMODE OR SINGLE MODE
OPTICAL FIBER
BLACK
BLACK WITH WHITE STRIPES
Power Supply:
Surface Mount: 8–15 VDC @ 2W
Rack Mount: From Rack
NOTE: Remove Electrical Connector for
Rack Mount Units
FIGURE 2 – FVT1031 TRANSMITTER
FIGURE 3 – FVR1031 RECEIVER
FRONT PANEL
FRONT PANEL
Tech Support: 1.888.678.9427
REAR PANEL
REAR PANEL
INS_FVT/FVR1031_REV–
02/05/10
PAGE 2
INSTALLATION AND OPERATION MANUAL
FVT/FVR1031(M)(S)1
FIGURE 4 – LED INDICATORS
GREEN
RED
LINK
VIDEO
DATA IN
DATA OUT
Communication link
An active video signal
An active data signal
An active data signal is Unit powered up
has been established
is present on the BNC
is present on the
present on the output
over optical fiber
connector.
input pins of the data
pins of the data
connector.
connector.
–
–
Communication
link has not been
established.
–
OFF
POWER
–
Unit powered down.
FIGURE 5 – DATA CHANNEL CONNECTIONS
FIGURE 6 – SWITCH POSITIONS
The mode for each data channel is configured using a pair of switches on the front panel of the unit.
1
Switch
Tech Support: 1.888.678.9427
2
Up-the-Coax
Protocols
1
2
RS485
4-Wire Data
1
2
RS232 Data
1
2
RS422, RS485
2-Wire Bi-Phase or
Manchester Data
INS_FVT/FVR1031_REV–
02/05/10
PAGE 3
INSTALLATION AND OPERATION MANUAL
FVT/FVR1031(M)(S)1
FIGURE 7 – DATA CONNECTIONS
Customer
Equipment
UTC Control
FVR1031
VIDEO IN
VIDEO OUT
FVT1031
FVR1031
Data Transmit
DIN
DOUT
Data Receive
Data Receive
DOUT
DIN
Data Transmit
Signal Ground
GND
GND
Signal Ground
Data Out (+)
DIN(+)
DOUT(+)
Data In (+)
Data Out (–)
DIN(–)
DOUT(–)
Data In (–)
Data In (+)
DOUT(+)
DIN(+)
Data Out (+)
Data In (–)
DOUT(–)
DIN(–)
Data Out (–)
Data Out (+)
DIN(+)
DOUT(+)
Data In (+)
Data Out (–)
DIN(–)
DOUT(–)
Data In (–)
Data (A)
A
A
Data (A)
Data (B)
B
B
Data (B)
Data Out (A)
A
DOUT(+)
Data In (A)
Data Out (B)
B
DOUT(–)
Data In (B)
Data In (A)
DOUT(+)
A
Data Out (A)
Data In (B)
DOUT(–)
B
Data Out (B)
Up-the-Coax
Control Receiver
Customer
Equipment
RS232
RS422
Bi-phase or
Manchester
2-Wire
RS485
4-Wire
RS485
Customer
Equipment
FVT1031
Tech Support: 1.888.678.9427
Up-the-Coax
Control Transmitter
Customer
Equipment
INS_FVT/FVR1031_REV–
02/05/10
PAGE 4
MECHANICAL INSTALLATION INSTRUCTIONS
Installation Considerations
This fiber-optic link is supplied as a Standalone/Rack module. Units should
be installed in dry locations protected from extremes of temperature and
humidity.
C1-US, C1-EU, C1-AU or C1-CH Card Cage Racks
Figure A
Dimensions are for a standard ComNet™ one slot module
.156 [3.96 mm]
CAUTION: Although the units are hot-swappable and may be installed
without turning power off to the rack, ComNet recommends that the
power supply be turned off and that the rack power supply is disconnected
from any power source. Note: Remove electrical connector before
installing in card cage rack.
1. Make sure that the card is oriented right side up, and slide it into the
card guides in the rack until the edge connector at the back of the card
seats in the corresponding slot in the rack’s connector panel. Seating
may require thumb pressure on the top and bottom of the card’s front
panel.
CAUTION: Take care not to press on any of the LEDs.
.313 [7.95 mm]
2. Tighten the two thumb screws on the card until the front panel of the
card is seated against the front of the rack.
WARNING: S tandalone units are to be used with a Listed Class 2 or LPS
power supply
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may
be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is not
compromised.
3 Corporate Drive | Danbury, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | Tech Support: 1.888.678.9427 | info@comnet.net
8 Turnberry Park Road | Gildersome | Morley | Leeds, UK LS27 7LE
T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | info-Europe@comnet.net
© 2012 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
INS_FVT/FVR1031_REV–
02/05/10
PAGE 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising