XX-LARGE STAND-OFF MOTOR MOUNT
XX-LARGE STAND-OFF
MOTOR MOUNT
ITEMS INCLUDED
(4) 50mm [2"] Aluminum Spacer
(4) 20mm [25/32"] Aluminum Spacer
(4) 10mm [13/32"] Aluminum Spacer
(4) 5mm [3/16"] Aluminum Spacer
(4) 2.5mm [3/32"] Aluminum Spacer
(8) 10mm [13/32"] Mount Bases
(4) 1/4-20 x 5" [127mm] Socket Head Cap Screw
(4) 1/4-20 x 4" [102mm] Socket Head Cap Screw
(4) 1/4-20 x 3" [95mm] Socket Head Cap Screw
(4) 1/4-20 x 2" [51mm] Socket Head Cap Screw
(4) 1/4-20 Blind Nut
(4) 1/4" [6.4mm] Flat Washer
(4) 1/4" [6.4mm] Split Lock Washer
XX-LARGE STAND-OFF
MOTOR MOUNT
ITEMS INCLUDED
(4) 50mm [2"] Aluminum Spacer
(4) 20mm [25/32"] Aluminum Spacer
(4) 10mm [13/32"] Aluminum Spacer
(4) 5mm [3/16"] Aluminum Spacer
(4) 2.5mm [3/32"] Aluminum Spacer
(8) 10mm [13/32"] Mount Bases
(4) 1/4-20 x 5" [127mm] Socket Head Cap Screw
(4) 1/4-20 x 4" [102mm] Socket Head Cap Screw
(4) 1/4-20 x 3" [95mm] Socket Head Cap Screw
(4) 1/4-20 x 2" [51mm] Socket Head Cap Screw
(4) 1/4-20 Blind Nut
(4) 1/4" [6.4mm] Flat Washer
(4) 1/4" [6.4mm] Split Lock Washer
ASSEMBLY
ASSEMBLY
1. Make a 1:1 photocopy of the motor mounting bolt
template on the opposite side of this manual. Cut
out the template that corresponds to the X-mount
you will use. Note: The X-mount that is included
with the RimFire™ 50cc and the RimFire 65cc motors
has a mounting pattern that matches the DLE-55
gasoline engine. You may also order the optional DA50 X-mount (GPMG1214) to match the DA-50 gas
engine’s mounting pattern.
4. Use a 3/16" hex wrench to draw the blind nuts into
the back of the firewall with one of the mount bases
and a short 1/4-20 bolt. Optional: Apply medium CA
around each blind nut to permanently hold it into the
back of the firewall – use care NOT to get any CA into
the threads.
1. Make a 1:1 photocopy of the motor mounting bolt
template on the opposite side of this manual. Cut
out the template that corresponds to the X-mount
you will use. Note: The X-mount that is included
with the RimFire™ 50cc and the RimFire 65cc motors
has a mounting pattern that matches the DLE-55
gasoline engine. You may also order the optional DA50 X-mount (GPMG1214) to match the DA-50 gas
engine’s mounting pattern.
4. Use a 3/16" hex wrench to draw the blind nuts into
the back of the firewall with one of the mount bases
and a short 1/4-20 bolt. Optional: Apply medium CA
around each blind nut to permanently hold it into the
back of the firewall – use care NOT to get any CA into
the threads.
2. Use the motor mounting bolt template you selected
to mark the bolt hole locations on your firewall.
Align the template with the alignment marks on your
firewall.
2. Use the motor mounting bolt template you selected
to mark the bolt hole locations on your firewall.
Align the template with the alignment marks on your
firewall.
5. Select the mount base/spacer/bolt combination
necessary to extend your motor the correct distance
from the firewall. Apply a few drops of threadlocker
to the threads on the end of the mounting bolts. Then,
mount your motor using 1/4" [6.4mm] lock washers
and 1/4" [6.4mm] flat washers under the heads of
the bolts.
5. Select the mount base/spacer/bolt combination
necessary to extend your motor the correct distance
from the firewall. Apply a few drops of threadlocker
to the threads on the end of the mounting bolts. Then,
mount your motor using 1/4" [6.4mm] lock washers
and 1/4" [6.4mm] flat washers under the heads of
the bolts.
3. Drill 1/8" [3.2mm] guide holes through the firewall 6. Make certain your motor is secure and all the bolts
at the marks you made with the template. Then, are tightened. Always use a balanced propeller.
enlarge the guide holes with a 9/32" [7.1mm] drill to
accommodate the blind nuts.
3. Drill 1/8" [3.2mm] guide holes through the firewall 6. Make certain your motor is secure and all the bolts
at the marks you made with the template. Then, are tightened. Always use a balanced propeller.
enlarge the guide holes with a 9/32" [7.1mm] drill to
accommodate the blind nuts.
© 2009 GPMG1275INSTR
© 2009 GPMG1275INSTR
78mm
RimFire 50cc & 65cc
Motor Mounting Bolt Template
(DA-50)
78mm
66mm
80mm
RimFire 50cc & 65cc
Motor Mounting Bolt Template
(DLE-55)
RimFire 50cc & 65cc
Motor Mounting Bolt Template
(DA-50)
66mm
80mm
67mm
RimFire 50cc & 65cc
Motor Mounting Bolt Template
(DLE-55)
67mm
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising