3160EC Quick Install Guide

3160EC Quick Install Guide
MO D E L 3160E C E AS Y- C LOS E
DRAWER PREPARATION
QR Installation
Video
FORMULA FOR CALCULATING DRAWER BOX LENGTH
Slide length = Outside drawer box length
CABINET MEMBER
5
(Example: If slide length = 16", the outside length of the drawer box = 16")
FORMULA FOR CALCULATING DRAWER BOX HEIGHT
Maximum drawer height = cabinet height minus 13/16"
FORMULA FOR CALCULATING DRAWER BOX WIDTH
For drawer side thickness:
5/8"
16mm
19/32" 15mm
9/16"
14mm
1/2"
1
2
13mm
9/16"
15mm
5/8"
17mm
3/4"
13mm
Overlay Drawer
(side view)
19mm
#8-32 Pan Head
Screws
Pre-assembled
6
Pre-assemble the
stabilizer carrier
strip as shown.
Screw and
connector clips
are needed.
.063 [1.6] Gap
For inside drawer width,
deduct from inside cabinet width: 1-3/4" 44.45mm 1-3/4" 44.45mm 1-3/4" 44.45mm 1-3/4" 44.45mm
For outside drawer width,
deduct from inside cabinet width: 1/2"
WIDE DRAWER STABILIZER KIT
Predrill a hole 37 mm from the cabinet front.
Drawer Box Length tolerance +0/-1/16"
Q U I C K
Stabilizer Carrier
Strip
Logo
(facing Up)
(Drawers 41"-60" only)
#8-32 X 3/8''
Pan Head Screws
to connect
Carrier Strip
& Connector Clips
Connector Clips
(2X)
Logo
(facing Down)
7
Notch drawer
1/2''
max.
Locate and
drill 3/8" deep
drawer hook
holes
.063 [1.6] Setback
1.457 [37.0]
1/4''
7/16''
Predrill a hole 37 mm from the cabinet front.
1/4'' dia.
Locate and drill 3/8'' deep
drawer hook holes
CABLE SYSTEM
3/4" [19.1]
5/8" [15.9]
Inset Drawer
(side view)
10º
Pulley Bracket
With slide in the
closed position
placed stabilizer
strips under
pulley bracket
and insert
screws thorough
the key holes.
S T A R T
CABLE SYSTEM
(31"-60" wide)
Continued
11
Once gap is
achieved, secure
cable with cable
locking screw.
Close gap by
turning cable
tension screw,
then make one
more additional
turn. Check
movement.
NOTE: Too
much tension
may cause poor
movement.
Installation
Direction
G U I D E
1/8" Gap
Cable Tension Screw
1/8" Gap
Closed
Gap
Cable Tension Screw
12
(31"-60" wide)
Repeat steps 8-11 on the opposite side but at the
end, carrier strip should go over locking screw.
1
8
Start on the right hand side. Uncoil
cable through back bracket and
along roller
9
Route cable along the roller system, starting on the back
right hand roller and ending on the left front roller.
2
11/16"
Predrill holes
at a 10º angle.
1-5/8"
7/32"
0.875 [22.2] Setback
1.457 [37.0]
General components
Slide
3
4
To locate disconnect lever holes,
place the disconnect assemblies
flush against each corner and
mark the holes.
Cabinet
13
•Adjust drawer front
horizontally,
vertically, and
front to back
as needed.
•To lock, turn
the black cam,
adjust 1/4 turn
clockwise.
Connector Clips
Roller
Install disconnect levers. Levers should curve toward the
center of the drawer. Use #6 x 5/8" pan head screw.
Pulley Bracket
#6 X 5/8" L
pan head
screw
for levers
3700-9564 MK 984-0117
14
10
Front to back
adjustment cam
1/2" thick
drawer spacer
Horizontal
Adjust
(gray)
Vertical
Adjust
(blue)
Lateral Lock
(black)
3
Standard lever
can be installed
vertically or
horizontally.
©2017 ACCURIDE INTERNATIONAL INC.
1
2
Cable Bracket
Stabilizer
Carrier
Strip
3
#8 X 5/8" L
flat head
screw for
cabinet member
#8 X 5/8" L
pan head
screw for
rear bracket
Route cable
through cable slot,
pull cable until
an 1/8" gap is
achieved as shown
in Figure 11.
Tighten all screws, check movement, cut cables.
NOTE: Install knobs or pulls after drawer fronts are adjusted to
ensure proper alignment.
Cable Slot
Cable Locking Screw
Cable Tension Screw
12311 Shoemaker Avenue • Santa Fe Springs, CA 90670
(562) 903-0200 • www.accuride.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising