9ft Jib Arm with Tripod (P-9-TS)

9ft Jib Arm with Tripod (P-9-TS)
9ft Jib Arm with Tripod
(P-9-TS)
INSTRUCTION MANUAL
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permitted by
the applicable copyright statutes or in writing by the publisher.
PROAIM 9FT JIB WITH STAND
2
INTRODUCTION
Some call it the money shot, we call it the Proaim 9’ Jib. A sophisticated piece of engineering that
is easy to use and provides amazing ‘picture perfect’ results. All this and more and it comes in a
easy carry bag. Another smart choice for digital media shooters from PROAIM.
IN THE BOX
Please inspect the contents of your shipped package to ensure you have received all that is
pictured and listed below. The padded shipping /storage container has been especially designed
to protect your purchase while in transit and is a good place to keep your 9’ Jib when not in use.
KIT CONTENTS








Two 3.9ft sections
Camera Platform
LCD Mounting Arm
Control Handle
Locking Pin
Jib Stand
Tools Kit
Packing Bag
Using the following pictures and text as a guide for set up, please follow the instructions in
order of appearance.
JIB STAND SET UP
For stability and mounting of your 9’ Jib Arm on the stand, remove the stand from the case and
proceed as follows:
 Loosen the lower knob 1 located at the top of the spreader legs.
 Slide the legs down the center post to the widest possible position and tighten the knob 1
to secure. A wider spread ensures more stability.
 Draw the center post up to the desired jib height and lock into place using the provided
locking pin.
PROAIM 9FT JIB WITH STAND
3
Knob 1
ASSEMBLING THE JIB ARM
MOUNT THE CENTRAL POST OF THE JIB ON THE STAND

Slide the Center Post of the Jib onto the
Stand Mount and secure it with provided
knob.
CONNECT THE END SECTION TO THE CENTER POST

Attach the End section of Jib with the
Center Post.

Using a wrench, tighten the dome nut
from both sides to secure the two sections.
CONNECTING FRONT SECTION TO END SECTION


The front section has connecting bars attached to one end as shown. Slide the bars of end
section into the slots on front section tightening the two sections together using the supplied Allen Key.
Tighten the Allen keys as before to secure the sections. Your arm build is now complete.
PROAIM 9FT JIB WITH STAND
ADDING THE COUNTER WEIGHTS



Securing the counter weights to the Jib is
accomplished by the use of the stainless
steel shank. It has two lock offs, one for
each side of the Arm to prevent the
weights from shifting during use or
accidentally falling off the jib.
Standard exercise weights (not supplied)
with a 1’ hole are easily rig mountable and
are used to equal the weight placed on the
camera side of the Jib.
Once you discover correct balance,
consider marking the weights for that
particular camera facilitating an easier set
up the next time.
CAMERA MOUNTING PLATE


To accommodate various manufacturers
and different sized cameras, multiple slots
are provided for attachment.
You will need to fine tune your
counterweights to accommodate camera,
head and other accessories being used on
the Jib Arm.
MOUNTING THE PAN/TILT HEAD

If you are using the remote capability of a
Pan/Tilt Head, it can be easily mounted to
the jib via the 4 slots located at the
corners of the plate using 4 screws. Pan/
Tilt Head is not provided.

This assembly is usually accomplished
from the underside (bottom) of the jib
camera plate.
4
PROAIM 9FT JIB WITH STAND
5
PIN FEATURE FOR TILTING SHOTS

Removing the locking pin on the Center Post allows the operator to frame tilting shots by
use of the control handle.

Lock the pin for keeping your camera in a
fixed angle to take stable shots.
MOUNTING A MONITOR

Provisions for LCD monitor mounting to
the Jib Arm are built in. The monitor is
not provided.
YO U R P R O A I M 9 ’ J I B W I T H S TA N D
SET UP COMPLE TED AND GOOD TO GO
PROAIM 9FT JIB WITH STAND
6
SHOWN WITH OPTIONAL ACCESSORIES
WARRANTY
We offer a limited time warranty for our products. For Mechanical products we provide a 6
month warranty & for electronic products we provide a 3 month warranty from the date of
purchase.
We will repair or replace your product, free of charge, in the event of a defect in materials or
craftsmanship obtained during normal use or handling based on the user manual. Please note
that we will not cover any shipping costs for returning the product to us. If any VAT or import
duties are applied to the return, we will also charge these costs to the customer.
The warranty does not include, by the way of example, damage caused by products that we do
not supply or from mishandling in transit, accident, misuse, neglect, lack of care of the product ,
or service by anyone other than our company.
We are not liable for incidental or consequential damages resulting from the use of the unit or
occurring due to any breach of this warranty.
Replacement parts of the product will be provided at nominal cost (covering the cost price of the
replacement parts only) to the customers after the Warranty Period has expired. We will cover
the complete cost of sending replacement parts within the warranty period. After that, Nominal
cost of the product & Actual shipping cost will be charged.
Do not send the unit to us without first getting a response and getting the approval to send back
the item.
In case of any kind of dissatisfaction, we urge you to Contact us immediately and we shall do our
best to help you out.
For any other assistance you can reach us via email.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising