ksa1013 installation instructions
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Laptop Tray Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KSA1013
KSA1013
DISCLAIMER
CSAV, Inc., and its affiliated corporations and subsidiaries
(collectively, "CSAV"), intend to make this manual accurate and
complete. However, CSAV makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of
warranty, expressed or implied, regarding the information
contained herein. CSAV assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.
Installation Instructions
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity of the mount
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
2
can result in serious personal injury or damage to equipment!
It is the installer’s responsibility to make sure the combined
weight of the mount and all attached components does not
exceed 18lbs (8.16kg).
Installation Instructions
KSA1013
LEGEND
Tighten Fastener
Phillips Screwdriver
Apretar elemento de fijación
Destornillador Phillips
Befestigungsteil festziehen
Kreuzschlitzschraubendreher
Apertar fixador
Chave de fendas Phillips
Serrare il fissaggio
Cacciavite a stella
Bevestiging vastdraaien
Kruiskopschroevendraaier
Serrez les fixations
Tournevis à pointe cruciforme
Loosen Fastener
Hex-Head Wrench
Aflojar elemento de fijación
Llave de cabeza hexagonal
Befestigungsteil lösen
Sechskantschlüssel
Desapertar fixador
Chave de cabeça sextavada
Allentare il fissaggio
Chiave esagonale
Bevestiging losdraaien
Zeskantsleutel
Desserrez les fixations
Clé à tête hexagonale
TOOLS REQUIRED FOR INSTALLATION AND PARTS
5/32" (provided)
3/16" (provided)
B (1)
3/16"
A (1)
C (1)
5/32"
D (1)
E (1)
H (1)
5/16-18 X 2 1/4"
F (1)
G (1)
5/16-18
K (1)
L(1)
J (1)
5/16-18 X 3 1/2"
3
KSA1013
Installation Instructions
INSTALLATION
Existing Mount Preparation
H or J (1)
If the KSA-1013 is being installed on an existing Chief
swingarm style mount the existing mount needs to be modified
before installation of the KSA-1013. If there is no existing mount
proceed to "Tray Installation" section below
F (1)
A (1)
To prepare the existing mount:
1.
1.
Disconnect all cables and wiring from display.
Remove display, if present, from existing mount following
the instructions supplied with mount.
2.
Loosen button head cap screw securing display end of
mount to mount arm using a 5/32" hex key.
3.
Uninstall button head cap screw, one nylon washer, and two
flat washers from swing arm and set aside for reuse.
(See Figure 2)
4.
E (1)
Remove large nylon washer, pivot pin, and Nylock nut from
existing mount base and set aside for reuse.
(See Figure 2)
D (1)
BHCS
G (1)
Mount Arm
Flat Washer
Figure 2
Nylon Washer
Swing Arm or other
mount end.
Flat Washer
Laptop Installation
To install a laptop computer onto the KSA-1013:
1.
Loosen the two locking thumbscrews on tray bottom.
2.
Pull Slide trays outward to fully open position.
(See Figure 3)
Large Nylon Washer
Pivot Pin
Locking Thumbscrews
Existing Mount Base
Nylock Nut
Figure 1
Slide Tray
Tray Installation
View from tray bottom
To install the KSA-1013:
1.
Place pivot pin (D) into mount end. (See Figure 2)
2.
Place nylon spacer (E) on top of mount end.
3.
Assemble UHMW washer (F) to BHCS (H or J).
4.
Install threaded end of BHCS (H or J) through access hole
in tray top and down through mounting tab of tray assembly
(A), down through spacer (E), pivot pin (D) and through
mount end.
5.
Slide Nylock nut (G) up into bottom of mount end.
6.
Hold Nylock nut (G) in bottom of mount and tighten BHCS
(H or J) to desired tension. (See Figure 2)
4
Figure 3
Installation Instructions
3.
KSA1013
Position Laptop so that it is centered and resting against the
front edge of tray. (See Figure 5)
Slide Tab
(two places)
Slide Tab Retaining Screw
(two places)
Front Edge
Figure 4
4.
Push slide trays inward until slide tabs rest against side of
laptop. (See Figure 5)
5.
Tighten two locking thumbscrews on tray bottom.
Figure 6
ADJUSTMENTS
Tray Pitch Adjustment
Slide Tabs
Locking Thumbscrews
To adjust the tray vertical position:
1.
Loosen tray pitch adjustment screw by turning screw
counter-clockwise using 3/16" hex wrench.
2.
Reposition tray.
3.
Tighten tray pitch adjustment screw by turning clockwise
using 3/16" hex wrench.
Slide Tabs
Figure 5
6.
Loosen two slide tab retaining screws. (See Figure 6)
7.
Position slide tabs so they are not blocking any ports on
laptop. (See Figure 6)
8.
Tighten two slide tabs. (See Figure 6)
Pitch Adjustment Screw
Figure 7
5
KSA1013
Installation Instructions
Rubber Pad Installation
To install protective rubber pad:
1.
Position tray and arm as shown in the figure below.
2.
Remove paper from back of rubber pad (L) to expose
adhesive surface.
3.
Position rubber pad (L) on mount arm as shown in figure
below.
4.
Secure rubber pad (L) to mount arm by pressing adhesive
side of pad onto arm.
L (1)
Figure 8
6
Installation Instructions
KSA1013
7
KSA1013
Installation Instructions
USA/International
Europe
Asia Pacific
8807-000036
2007 Chief Manufacturing
www.chiefmfg.com
02/07
A
P
F
A
P
F
A
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 40 2668620
+31 (0) 40 2668615
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
P +86-755-8996 9226 ; 8996 9236 ; 8996 9220
F +86-755-8996 9217
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising