EF-NAC-802,1042 Rev C (01.10).cdr
Series
EF-NAC Series
FEATURES:
·
·
·
·
·
·
·
·
·
·
·
24VDC output
8 or 10 amp max total alarm current
Class A or Class B outputs
115VAC 60Hz, 4.4 Amp
Short circuit and thermal overload protection
Built-in charger for sealed lead acid or gel type
battery backup
Maximum charge current 0.7 Amp
Zero voltage drop upon transfer to battery
backup
AC input and DC output LED indicators
AC fail supervision (form "C" contact rated 1
amp, 28VDC)
Low battery and battery presence supervision
(form "C" contact rated 1 amp, 28VDC)
Notification Appliance Control
Power Supply
EF-AL-NAC-802ULADA NAC Power Extender
Overview
Model EF-AL-NAC-802ULADA is an extremely cost effective 8
amp voltage regulated remote power supply/battery charger. It
may be connected to any 12 or 24 volt Fire Alarm Control Panel
(FACP). Primary applications include Notification Appliance
Circuit (NAC such as strobes and horns) expansion support to
meet ADA requirements. It also provides auxiliary power to
support system accessories. The unit delivers regulated and
filtered 24 or 12 volt power to Class B or Class A NAC loop
circuits. Additionally, a separate 1.0A auxiliary output with reset
for four (4)-wire smoke detectors is available. The 8 amp rated
supply current can be divided between the four (4) outputs for
powering NAC devices. Each output is rated at 2.5 amp max.,
and can be independently programmed for Steady, Temporal
Code 3 or Strobe Synchronization. All outputs may be
programmed for Input to Output Follower Mode (output will
follow input. i.e. March Time Input, March Time Output). An
individual output of 4 amp is achieved by paralleling 2 outputs.
In non-alarm condition independent loop supervision for Class A
and/or Class B FACP NAC circuits is provided. In the event of a
loop trouble the FACP will be notified via the steered input (input
1 or input 2). In addition, there are common trouble output
terminals (N.C., C, N.O.) which are used to indicate general
loop/system trouble. A common trouble input is provided for
optional NC (normally closed) devices to report trouble to the
FACP. Two (2) FACP signaling outputs can be employed and
directed to control supervision and power delivery to any
combination of the four (4) outputs. The unit also features “Loop
Output” trouble memory indication to help identify troublesome
sporadic problems.
NOTE:
Refer to Installation manual for specific installation
and product information, catalog sheet for reference
only.
20 McDermott Road, Branford, CT 06405
EF-AL-NAC-1042ULADA NAC Power Extender
Overview
Model EF-AL-NAC-1042ULADA is an extremely cost
effective10 amp voltage regulated remote NAC Power
Extender. It may be connected to any 12 or 24 volt Fire Alarm
Control Panel (FACP). Primary applications include
Notification Appliance Circuit (NAC) expansion (supports ADA
requirements) and will provide auxiliary power to support
system accessories. The unit delivers regulated and filtered
24 or 12 volt power via up to four (4) Class B, four (4) Class A
or combination of Class B and Class A Notification Appliance
Circuits. Additionally, the unit can supply up to 1 amp from
continuous AUX output and up to 1 amp from AC
disconnected AUX output. The 10 amp rated supply current
can be divided between the four (4) outputs for powering
notification appliances and the AUX outputs. Each output is
rated at 2.5 amp max (total not to exceed 10 amp), and can
be independently programmed for Steady, Temporal Code 3
or Strobe Synchronization. All outputs may be programmed
for Input to Output Follower Mode (output will follow input. i.e.
March Time Input, March Time Output). An individual output
of 4 amp is achieved by paralleling 2 outputs. In non-alarm
condition units provide independent loop supervision for
Class A and/or Class B FACP NAC circuits. In the event of a
loop trouble the FACP will be notified via steered inputs (input
1 or input 2). In addition, there are common trouble output
terminals (N.C., C, N.O.) which are used to indicate general
loop/system trouble. A common trouble input is provided for
optional NC (normally closed) devices to report trouble to the
FACP. Two (2) FACP signaling outputs can be connected to
power extender inputs. These inputs can then be directed to
control supervision and power delivery to any combination of
the four (4) outputs. The unit also features “Loop Output”
trouble memory indication to help identify troublesome
sporadic loop problems.
203-315-5116 FAX 203-315-5118
WWW.EVAX.COM
Multiple Power Supply interconnect wiring
FACP with Sync Output
FACP
(Fire Alarm
Control Panel)
or
Sync Module
ZONE 2
POWER
IN-
ZONE 1
+NAC2-
POWER
IN+
ZONE 1
POWER
IN-
???
CONTROL
+NAC1-
POWER
IN+
POWER
OUT+
To FACP EOL or
next Altronix
NAC Power Extender
POWER
OUTPOWER
OUT+
POWER
OUT-
2.2K
EOL
2.2K
EOL
2.2K
EOL
2.2K
EOL
2.2K
EOL
2.2K
EOL
2.2K
EOL
2.2K
EOL
These two wires are used for
synchronizing NAC Power Extenders
Class B Wiring
Class A wiring
+ AUX1 + AUX2 + AUX1 + AUX2 -
+ OUT4 + OUT3 + LOOP4 + LOOP3 -
+ OUT2 + LOOP2 -
+ OUT4 + OUT3 + LOOP4 + LOOP3 -
+ OUT2 + OUT1 + LOOP2 + LOOP1 -
+ OUT1 + LOOP1 -
To AUX
Devices
2.2K
EOL
To AUX
Devices
Single Class A
Outputs
2.2K
EOL
Single Class B
Outputs
2.2K
EOL
Paralleled Class A
Outputs
2.2K
EOL
Paralleled Class B
Outputs
Engineering Specifications:
HOW to Order:
EF-AL-NAC-802ULADA
8 Amp NAC power Extender 2 Class “A” or 4
Class “B” outputs
EF-AL-NAC-1042ULADA
10 Amp NAC power Extender 4 Class “A” or
Class “B” outputs
Notification Appliance Circuit Expander Power Supplies
shall be capable of either 8 or 10 amps. Each Power supply
shall be field selectable for either Class A or Class B output
notification, where applicable the power supplies shall
provide either 4 Class B or Class A circuits. The NAC power
supplies shall have internal protocols build into the units and
work in conjunction with Amseco, Faraday, Gentex
Wheelock and System Sensor. In addition shall provide up
to 1 Amp of auxiliary continuous output power. The NAC
power extenders shall be either Evax EF-AL-NAC802ULADA or EF-AL-NAC-1042ULADA.
Specifications are subject to change without notice. Specifications
are provided for information only and no responsibility is assumed
by Evax Systems, Inc. for their use.
EF-NAC Rev C (06.10)
Series
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising