power distribution connector strips 450*cus

power distribution connector strips 450*cus
POWER DISTRIBUTION
450 CONNECTOR STRIPS
POWER DISTRIBUTION
CONNECTOR STRIPS
450*CUS
Altman Lighting’s 450 Series Connector Strips feature rugged
steel construction, innovative data distribution, and a wide array of
available connector types and hanging hardware. Each Connector
Strip is custom built for the specifications of the project.
Pigtail and flush mount load connectors are pre-wired to spring
loaded terminals at the feed end of the strip. Connector Strips are
available with Active and Passive DMX-512A/RDM and Ethernet
Data management and can be mounted horizontally or vertically, dead hung or attached to movable rigging sets. The 450 is
suitable for installation in theatres, television studios, or anywhere a system of permanent circuit distribution and data
distribution for conventional, LED, and automated luminaires are desired.
Product Features:
•
•
•
•
•
•
Rugged 18 gauge steel construction with 14 gauge end
caps and joiners. Center holes on end caps provided for
conduit fittings
A variety of flush mount and pigtail connectors are
available for 20A, 30A, 50A, and 100A circuits.
Individual circuits can be wired to multiple pigtails or
receptacles.
Active or passive data management for distribution of
DMX-512A/ RDM to distributed dimmers, automated
fixtures, and LED Luminaires.
Optional per circuit indicator lamps available.
Easy to ship, assemble, and service
1-Tool Assembly (#2 Phillips Screwdriver)
•
•
•
•
•
DIN Rail mounted screw-less spring terminals for
termination of 20A loads (up to #8 AWG). Screw
terminals for 30A, 50A, and 100A wiring.
DIN Rail mounted control box for integration of DMX512A/ RDM Opto Splitters, Ethernet nodes, and other
DIN rail mounted control devices.
Standard 2” high white vinyl numbers for circuit
identification on one side. Numbering on both sides,
custom vinyl colors, and lamicoid circuit identification
plates are available.
cETLus Listed
Made in the USA.
POWER DISTRIBUTION
450 CONNECTOR STRIPS
Specifications
Power Receptacles
General:
•
Available in standard and custom lengths. Connector Strips over
6-feet come folded in sections, packaged for quick assembly.
•
Active and Passive Data Management available for DMX-512A /
RDM and Ethernet control signals.
•
Flat Black Finish. Custom colors are available - consult factory
•
Standard 2-inch high white vinyl numbers for circuit identification on
one side. Numbering on both sides, custom vinyl colors, and
lamicoid circuit identification plates are available.
•
cETLus Listed
Stage Pin (GSP)
Physical:
•
18 gauge steel construction with 14 gauge end caps and joiner
pieces.
•
20 gauge electro-zinc DMX (low-voltage) barrier
•
0.125-inch Center holes on end caps for conduit fittings
•
DMX & Flush Receptacle panels are on 3-inch centers. Pigtails are
on 1.5-inch centers.
•
All DIN Rail mounted components.
Data Management Options:
•
No DMX: No data distribution and management is built into the
connector strip.
•
Passive DMX (non-Opto Isolated): Up to (4) individual DMX-512A /
RDM Data Lines can be run through the strip to flush-mounted XLR
connectors. “Pass-thru” panels are provided for multiple
receptacles on a single data line.
•
Active DMX: DMX-512A/RDM Data is distributed throughout the
strip from a single source via Pathway eDIN Opto-Isolators
mounted in the control box.
•
Ethernet distribution solutions (integrated switches, Ethernet to
DMX nodes, etc.) are available.
•
Hardwired and optional XLR Receptacle data inputs available at
control box.
Power Input:
•
Circuits in the Connector Strip are pre-wired to a junction box,
which contains DIN-rail mounted terminal strips for easy
installation.
•
DIN Rail mounted screwless spring terminals for termination of 20A
loads (up to #8 AWG). Screw Terminals for 30A, 50A, and 100A
wiring.
•
Second Terminal Box added for configurations with more than (24)
20A circuits.
•
19-Pin Socapex/ VEAM power feed connections are available.
Connector Options:
•
Pigtail or Flush Mount 20A Stage Pin connectors
•
Pigtail or Flush Mount “Edison” (NEMA 5-15 and 5-20 connectors)
•
Pigtail or Flush Mount Twistlock (NEMA L5-15 and L5-20
connectors)
•
Other connectors including L620, 19-Pin Socapex/ VEAM, 30A,
50A, and 100A connectors are available.
20A, 50A, or 100A Stage Pin
Receptacle (20A shown)
Parallel Blade (PBG)
Parallel Blade or “Edison” receptacle (NEMA
5-20) will mate with NEMA 5-15 and NEMA
5-20 Plugs.
Twistlock (GTL)
20A Twistlock Receptacle, NEMA L-520
NOTE: All Connectors shown here are
available in either Flush mount or Pigtail
configurations. Standard pigtail lengths are
18-inches. Custom Pigtail lengths are
available (consult factory). Other connector
types and configurations are available.
Contact Altman lighting for additional
information.
Data Receptacles
Female 5-Pin XLR (DMX/RDM)
Flush mounted female 5-Pin XLR for
distribution of isolated and non-isolated
DMX-512A/RDM Signals.
Ethercon RJ-45 (Ethernet)
Flush mounted RJ-45 connector in XLR
shell for distribution of Ethernet Control
signals.
DMX Pass Thru
Male and Female 5-Pin XLR Receptacles
with push button switch to connect (pass
thru) and disconnect them.
Altman Lighting
57 Alexander Street
Yonkers, New York 10701
1.914.476.7987 (Main)
1.914.963.7304 (Fax)
www.altmanlighting.com
All specifications, descriptions,
information, design, etc. contained
in this document are subject to
change without prior notice.
15 December 2016
© 2016 Altman Stage Lighting, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising