DD-6212 - MRM Traders
Touch calibration
CONTENTS
If touch calibration error occurs, you can adjust the touch coordinate by “Touch calibration”.
Click
icon on setup interface, input password [888888] to confirm to access touch calibration interface, as shown in below diagram:
Panel function description
Remote control function
Turn on/off Host
Access main interface
U Disc/SD Card function operation
02
03
05
05
Touching methods
Use touch pen to click the center of “+” icon, and move along with center of “+” icon so as to calibrate the screen. It shall automatically
save data and exit after screen calibration.
Please accurately click all positions on screen, or the accuracy of touch calibration shall be affected.
05
Trouble shooting
Radio Function Operation
06
Disc Function Operation
07
BT Function Operation
08
MUSIC function operation
10
External input operation (Optional)
10
Other Function Operations
11
Access setup interface
12
General setting
12
Time setting
12
Language setting
13
Audio setting
13
Video setting
13
Radio setting
Touch calibration
Trouble shooting
01
13
14
14
PROBLEM
CAUSE
CORRECT ACTION
Check fuse
Change fuse same as the old one
Some factors cause MPU wrong operation
Press RES button on the panel by penpoint, then,
power on
Change battery or fuse
Reset information and save
Weak signal
Move the car to another place, then research
There is a disk inside
Remove disc before inserting another one
Disc is scratched
Change new disc
Put wrong side of disc into the unit
Slot to in the disk with sign side up
Lens is dirty
Clean lens by lens clean disc
Cannot switch
language/subtitle
There is only one language/subtitle in disc
If disc is not with multi-language/subtitle, it cannot
switch language/subtitle
No image
Other factors cause MPU wrong operation
Press [RES] button on the panel by penpoint, then,
power on
Cannot watch image
during driving
It’s not allowed to watch image during driving
Park the car in a safe place, put the car stall in “ P ”
postion, pull up the hand brake, parking brake wire
must be grounded
Cannot power on
After ignition switch
off, setting
information all lose
Poor performance of
radio station
Cannot load disk
Cannot play disc
14
Panel Introduction
Language setting
During use, you can select your familiar language to display menu by language setup.
Click
icon on setup interface to access language setting interface, as shown in right (PIC 1) diagram:
Click the corresponding [English] icon on the language bar desired to be set so as to switch the
language type, when there are more than 3 languages, direction icon shall pop up, click it to select
your familiar language.
16
18
17
Audio setting
Click
icon on setup interface to access audio setting interface, as shown in right (PIC 2) diagram:
You can turn on or turn off the existing functions on audio setting interface and adjust the rearview
volume.
Video setting
Click
icon on setup interface to access video setting interface, as shown in right (PIC 3) diagram:
At video setting interface, you can adjust brightness, contrast, saturation and hue of the video.
PIC 3
Radio setting
Click on
in setting interface, input password [123456] to enter as shown in right (PIC 4)
diagram:
Touch [Europe] icon in the radio interface, icon will popup, click on it to choose radio region.
PIC 4
13
1. SRC/VOL button
Press this button will turn on power, during working longer press
this button will turn off power, on any mode, shortly press will return
main menu, rotate this button will adjust volume level.
2. DVD button
In any mode, press the button to enter into DVD auto reading mode.
3. FM/AM button
In any mode, press the button to access radio mode.
Note: For certain machine model press the button in radio mode to
band switch.
4. MUTE button
Press the button to close volume output, re-press it to resume
previous volume level.
5. USB/SD slot
Connect USB device to read video and audio files.
Warning: You can only use either front or rear USB at a time. Never
connect both front and rear USB at the same time! This could cause
malfunctions.
Insert SD card to read video, audio and image files of large volume.
6. SEEK button
In radio mode, rotate the knob to select station upward/backward,
long rotate the knob to automatically scan station. In playback
mode, short rotate the knob to select song upward/backward, long
rotate it to achieve speed forward/backward function.
7. AUX slot
To input external audio.
Warning: You can only use either front or rear AUX at a time.
Never connect both front and rear AUX at the same time.
8. APS button
In radio mode, short press the button to browse memorized station,
long press to search stored stations automatically.
9. EQ button
In a source mode, press the button to enter equalizer setup.
10. DBAS button
Press this button to bass on/off.
11. RESET
Press this button can back to default mode.
12. ST/MO button
In radio mode, press the button to switch between mono and stereo.
In play mode, press the button to select sound track.
13. Eject disc
Press this button can eject the disc.
14. Disk enter/exit
Enter / exit disc window.
15. BT button
In any mode, press the button to enter BT mode.
16. AUX button
In any mode, press the button to access AUX mode.
17. IR
To receive infrared signals from the remote control matched with the
unit.
18. MIC
Input socket for microphone.
02
Remote control function
1. POWER button
Press once to switch on, press again to switch off.
2. MUTE button
Press once to turn off audio output, press again to resume volume
level.
3. DSP button
Press the button to show the time.
03
4. SOURCE button
Press this button to choose audio sources.
5. EQ button
Press this button to choose POP, ROCK, CLASSIC, EQ off.
6. SEEK+ ( )/ SEEK- (
)button
In normal playback MP3, USB, SD songs, press this button to
previous song or next song.
7. VOL+ ( )/ VOL- ( )
Press this button to increase or decrease volume level.
8. SEL button
Press this button to choose sound feature.
9. LOUD button
Press this button to startup LOUD function.
10. BAND - P/N button
In radio mode, press this button to choose band.
In VCD, DVD mode, press this button to choose AUTO, PAL or
NTSC system.
11. LOC/RDM button
In radio mode, press this button to switch between local and
direction, In VCD, CD mode, press this key to randomly play.
12. STOP button
Press this button to stop playing.
13. PLAY/PAUSE button
Press this button to switch between play and pause, In stop mode,
press this button to play.
14. ST/PROG button
In radio mode, press this button to choose stereo or mono station.
In audio mode, it can help stop button to programmed play.
Access setup interface
Click [Setting] icon on main interface to access setup interface.
General setting
Click
icon on setup interface to access general setting interface, as shown in below PIC 1 diagram:
In general setting interface, you can select to turn on or turn off the existing functions. You can set wallpaper and opening picture you
like and check version number of DVD/MCU/TFT, click icon to browse up/down.
Wallpaper selection
Click [Chinaware] icon on wallpaper bar [Wallpaper Chinaware],
Opening picture
Click [Standard] icon on opening picture bar [Logo Standard] ,
direction icon shall pop up, click it to select wallpaper.
direction icon shall pop up, click it to select opening picture.
Time setting
Click
icon on setup interface to access time setting interface, 12h/24h can interchangeable, as shown in below PIC 2 diagram:
Click [02 07] icon on time bar [Time 02 07] time setting interface shall display, as shown in below PIC 3 diagram:
Click icon beside hour and minute to separately set hour and minute.
12
Other functions
Rearview function
In any running state, the video signal can switch to reverse video state when reversing the car, and the system shall return to its initial
running state after reversing the car.
Warning
Do not rely on CCD system completely, please make
sure your car is safe by your eyes during driving.
Back rearview system only assists in driving. As the
distance range of rearview system is limited,
completely relying on the rearview system during
driving may cause accidents.
Rearview backup image
Reverse field simulation
11
15. 0-10+ button
Press this button to choose desired song, section, preset stations.
Decimal numbers, for example the 19th song, press 10+ and 9
button.
16. AMS/RPT button
In radio mode, press this button to browse stored stations. In audio
mode, press this button to play repeatedly.
17. TITLE button
In DVD mode, press this button to play back to the top menu of
disc.
18. AUDIO button
In DVD mode, press this button to switch language of dialogue.
In VCD mode, press this button to choose left track, right track,
and stereo.
19. GO TO button
In DVD mode, press this button, you can define playing time.
20. SUB-T button
In DVD mode, press this button to switch language of subtitle.
21. PBC button
In VCD mode, press this button to display all song menus, work
with number button to choose songs.
22. UP, DOWN, LEFT, RIGHT, ENTER button
When playing MP3, USB, SD returns to song menu, up, down
selections can be up / " " button or down / " " key to select up
and down, select and press " " key to confirm. The selected tracks
can be played.
Press the left or right arrow keys to " " or " " key, can be on the
next page function operation.
23. SLOW button
In audio mode, press this button to slow backward and slow
forward.
24. ANGLE button
In DVD mode, press this button to change play angle.
25. SETUP button
In audio mode, press this button to choose different set items.
26. OSD display
Press this button to display the title chapter and the left time.
27. ZOOM button
In DVD/VCD mode, press this button to ZOOM in/out.
28. MENU button
Press button to back to the main menu.
BATTERY CHANGE
When control distance of remote control becomes shorter or no
function, please change battery, please confirm polarity before
change.
One hand press stopper, then pull out battery.
Put battery into controller.
Insert battery holder into controller.
04
MUSIC function operation
Turn on/off Host
When the ignition switch is put in ACC or ON position, Press [
hold [ ] button for 3 seconds , the host will turn off.
] button on the front panel to turn on the unit. After the host starts,
Connect to Music first, touch [Music] icon on main interface to access Music interface, as shown in below diagram:
Access main interface
Volume adjustment knob
Play/Pause
Fast forward play/ Fast backward play
Turned on, the interface to return the icon to switch to the main interface. As shown below:
Stop
Touch the function icons so as to access the corresponding function operations.
Touch the [
] icon or use the touch pen/finger gently sliding around the screen to switch to the main menu page.
U Disc/SD Card function operation
When there is a USB device/SD card connected, the unit can conduct the playback of audio/video/image files in the USB device/SD card.
Insert/Eject USB storage device
1. Connect a U disc recorded with media information to the unit by a USB connecting cable.
2. When there is a need to eject the USB device, exit the USB device playback screen first, and then take out the device.
Insert/eject SD card
1. Insert a SD card recorded with media information into the SD card slot in the unit correctly until it is locked.
2. When pulling out the SD card, exit SD card playing state first, then press the SD card and it shall pop up after unlocking.
Enter/exit
Insert a USB storage device or SD card to automatically play data contained in it. If the unit has connected with a USB device or SD
card, touch [USB] icon in the multimedia interface to enter into the external storage playback interface; Touch [SD] icon to enter into
the SD card playback interface. During playback, touch the top center area of the screen to pop up the touch menu, operate touch
menu to perform various playback controls.
Play
After SD card/USB removable device being read out, the operation methods are similar to disk operation methods.
05
Previous Song/Next Song
Back to the main interface
External input operation (Optional)
Connect the video input plug with external video input jack, and connect the audio input plug with external audio input jack.
Touch [AUX] icon on main interface to access external AUX interface.
Audio →You can adjust the volume, bass, pitch for input audio. You can adjust the speaker volume by adjusting the front and back,
left and right column.
Video →You can adjust the brightness, contrast, saturation and hue for input video. You can also choose the video standard mode.
10
3. Dialing
You can dial on mobile phone directly or input phone number through the number buttons on the screen, click
input error.
After input the phone number, click
to make a call, and click
to hang up the phone.
Click
during a call so as to switch the voice between car speaker and mobile phone.
Radio Function Operation
1. Enter/exit
Touch [Radio] icon in the main interface to enter into the radio interface.
Touch
icon to return to main interface, and then touch other function icons so as to exit
radio mode.
2. Band selection
Click
icon so as to switch among FM1, FM2, FM3, AM1, AM2 bands.
4. Call records
Click
to access call records interface.
Touch this button to check all the dialed phone numbers.
Touch this button to check all the phone numbers of received calls.
Touch this button to check all the phone numbers of missed calls.
3. Search/Save radio stations
Short press
icon to browse the stored radio stations. FM band can save 18 radio stations (Six stations for FM1/FM2/FM3), AM band
can save 12 radio stations (Six stations for AM1/AM2).
4. Sound setting
Click
icon to access sound setting interface.
5. Turn on/off the Long/Short-range
Click
icon, the search pattern in the local search (LOC) and remote search (DX) switch between. LOC feature is turned on after the
signal is strong enough only to listen to those in good condition and receiving radio station; DX enabled, you can receive remote weak
radio signals.
Note: This function is available only when FM band is selected.
5. BT music
Click
to access BT music interface.
Previous song
Next song
Play/Pause
09
to delete if there is
6. Loudness on/off
Click
icon so as to turn on/off loudness function.
7. Stereo on/off
When receiving stereo signals, click
icon to turn on/off stereo.
06
Disc Function Operation
1. Play/eject disc
Play disc
Insert the disc into the disc slot with the printing surface up, system will detect the disc and automatically take it in to read and play.
Eject disc
(1) Click
button on the panel to eject the disc.
(2) If a disc has not been took away 15 seconds after it is ejected, system will automatically take in the disc but not play.
Do not insert two discs or more.
20
x
TT 1/1
CH 1/48
2. DVD/VCD disc playback
During playback of disc, touch the middle lower area of the screen to pop up the touch menu,
operate the touch menu to perform various playback controls. (PIC 1)
3. CD Disc Playback
After a CD is inserted, system shall access disk reading state immediately.
00: 01
: 44
00: 09: 43
When there is a disk in the device, click [Disk] at the main interface so as to access disk reading state.
After the disk being read out, system shall automatically play in sequence.
PIC 1
4. MP3/JPEG/MPEG4 disk playing
When the disk contains readable files, such as MP3/JPEG/MPEG4 files, it shall be automatically read out and played after slipping into
DVD player.
During playing, touch the screen area and the touch menu shall pop up. Operate the touch menu for various playing.
20
5. Touch Menu Function Description
x
TT 1/1
CH 1/48
Play/pause
Touch the button to pause, retouch it to continue to play.
Stop
Touch the button to enter into pre stop status.
Fast forward/backward
Consecutively touch this button to select the speed of fast-forward/fast-backward.
The previous/next song
Touch the button to select the previous/next song.
Volume adjustment button
Touch this button and volume adjustment modulation shall pop up, touch button to adjust the volume.
07
00: 01
: 44
00: 09: 43
Access next menu
Touch it to access the next menu interface.
Time setting
Touch this button to access time setting interface.
Stereo on/off
Touch it so as to turn on/off stereo.
Repeat play
In playing state, touch this button to start repeat play function:
Chapter repeat → Title repeat →Repeat All → Off.
During VCD playing, this function only works when PBC is off.
Language selection
Touch this button to select language.
Digit keyboard
Return to root menu
Touch this button and digit keyboard shall appear, click number
Touch this icon, it shall return to root menu of disk in DVD state and
access PBC menu playing in VCD state. All chapters in the disk shall be buttons directly to select tracks for playing.
displayed on the interface, touch the chapter icon directly for playing.
Switch play order
Touch this button to switch the play order.
Access title menu
Press this button to return to title menu of the disk. Directly click menu
Zoom in/Zoom out image
bar at title menu interface for playing.
Touch this button to zoom in /zoom out the image.
BT Function Operation
1. Enter/exit
Touch [ BT ] icon in the main interface to enter the BT interface.
Touch
icon to exit BT interface.
2. Pair/link
To use BT hand-free function, make connection first, i.e. match the host with the BT mobile phone.
Operation methods:
Set the host to be matching state, and open the BT of your mobile phone and use the mobile phone to search device, the mobile phone
shall prompt to match password with the BT when it has searched the BT device.
Input BT password (0000) to the mobile phone and confirm. The mobile phone shall prompt whether authorize to this device, please
select [Yes]. Phone and BT shall automatically connect within 20 seconds. Under any working mode, the host shall convert to BT state
if there is an incoming call. And the host shall restore to current mode after hanging up.
When the BT device matches with this device, the connection status shall display “LINK OK”, otherwise, it shall display “NO LINK”.
08
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising