CDV07 - Axon.tv
CDV07
Analog video (B&B / Tri-Level) distribution amplifier
(word clock DA for high impedance circuits)
A Synapse® product
COPYRIGHT ©2010 AXON DIGITAL DESIGN BV
ALL RIGHTS RESERVED
NO PART OF THIS DOCUMENT MAY BE REPRODUCED IN ANY FORM WITHOUT THE PERMISSION OF
AXON DIGITAL DESIGN BV.
ANALOG VIDEO DISTRIBUTION
Block schematic & I/O panel
BPL01
BPL07
ANALOG VIDEO INPUT
ANALOG VIDEO OUTPUT 1(OR LOOP BPL07 only)
ANALOG VIDEO OUTPUT 2
ANALOG VIDEO OUTPUT 3
ANALOG VIDEO OUTPUT 4
ANALOG VIDEO OUTPUT 5
ANALOG VIDEO OUTPUT 6
ANALOG VIDEO OUTPUT 7
ANALOG VIDEO OUTPUT 8
July 2009
CDV07
ANALOG VIDEO DISTRIBUTION
Features & Applications
The CDV07 is a basic analog distribution amplifier providing a low loss electronically balanced input
with loop through when used with the BPL07 or terminated when used with the BPL01. If
necessary the input can be used fully floating by unscrewing the tabs on the BPL07.
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Adjustable input gain
DC coupled
Compatible with Tri-Level sync
Compatible with Word clock for high impedance circuits
Floating inputs and loop through with BPL07
+/- 6dB gain adjustment
Input status detection
Full control and status monitoring through the front panel of the SFR04/SFR08/SFR18
frame and the Ethernet port (ACP)
Applications
The CDV07 is designed for applications where a cost effective analog video or Black & Burst
distribution is needed. The straightforward design enables easy installation and reliable operation.
ƒ
ƒ
Can be used for word clock distribution into high impedance circuits
Tri-Level sync distribution
Ordering information
Module:
ƒ
CDV07: Analog video distribution amplifier
Standard I/O:
ƒ
BPL01_CDV07: I/O panel for CDV07
ƒ
BPL07_CDV07: I/O panel for CDV07 with loop through
July 2009
CDV07
ANALOG VIDEO DISTRIBUTION
Specifications
Analog input
Input levels
Return loss
Common mode rejection (CMR)
700 mV. White to black. Nominal 1 V sync tip to white.
75 Ohms terminated with BPL01. Floating with BPL07
Measured with Mini Circuits ZFDC-15-6-75
> 40 dB, @ 5 MHz
> 36 dB, @ 15 MHz
> 28 dB, @ 30 MHz
75 Ohms terminated
Measured with BPL07 BNC inputs floating
CM signal on both inner and outer leads.
CM input impedance 5K Ohms. 10 KOhms each input
to GND
> 68 dB, @ 50Hz
> 55 dB, @ 5 MHz
> 40 dB, @ 15 MHz
> 30 dB, @ 30 MHz
Analog outputs
Output levels
Number of outputs
Return loss
1 V sync tip to white, 75 Ohms terminated
7 with BPL07, 8 with BPL01
Measured with Mini Circuits ZFDC-15-6-75
> 37 dB, @ 5 MHz
> 34 dB, @ 15 MHz
> 29 dB, @ 30 MHz.
Other outputs 75 Ohm terminated
Performance
Frequency response
Signal to noise ratio
Bar tilt
Gain stability
within 0,4 dB, 0 to 5 MHz.
66.5 dB. 10KHz to 6MHz, Tektronix VM700T
0,1 %
1%
Miscellaneous
Weight
Operating Temperature
Dimensions
Approx. 250g
0° C to +50° C
137 x 296 x 20 mm (HxWxD)
Word-clock distribution
Input voltage
Output voltage
Maximum 5V
Maximum 3.5V into high impedance (1K Ohms)
Electrical
Voltage
Power
July 2009
+24V to +30V
<5 Watts
CDV07
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising