Viking PROX-3 Medium Range Proximity Card Reader Specifications

Viking PROX-3 Medium Range Proximity Card Reader Specifications
TECHNICAL
Practice
Practice
TELECOM SOLUTIONS
FOR THE
PROX-3
Medium Range
Proximity Card Reader
2 1 S T C E N T U RY
November 14, 2011
High Performance Proximity Card Reader with up to 16 inches*
of Read Range and Optional Gooseneck Pedestal Mounting Kits
The model PROX-3 is a high performance
medium range HID compatible 125KHz
proximity card reader. The PROX-3’s compact size yet long read range of up to 16
inches* make it ideal for parking control,
gate access, turnstiles, etc. It is designed to
be mounted directly to a wall, post, single
gang electrical box or use an optional
mounting kit (see models below) for attaching it to a gooseneck pedestal. Mounting is simplified with horizontal and vertical mounting slots, which allow the reader to be conveniently adjusted and
leveled. To increase vandal resistance the chassis is a single piece design with
the mounting screws concealed behind a UV stable label.
The proximity card reader transmits data in 26-Bit Wiegand format, making it
compatible with any of the Wiegand equipped Viking entry controllers. The
PROX-3 is equipped with Enhanced Weather Protection (EWP) for outdoor
installations where the unit is exposed to precipitation or condensation. With
its sealed connections and fully potted electronics the PROX-3 is designed to
meet an IP66 Ingress Protection Rating. For more information, see DOD# 859.
PROX-3 shown with
VE-GNP pedestal and
PROX-3-MK-GNP
mounting kit
PROX-3 shown with
VE-GNP pedestal,
PROX-3-MK-VEGNP
mounting kit and
K-1700-3 with
VE-6x7
Features
Applications
•
•
•
•
• Parking control, gate access, turnstiles, etc.
• Compatible with these Viking products:
•
•
•
•
•
•
Read range of up to 16 inches*
Standard 26-bit Wiegand interface
HID compatible
Surface mounts to non-metallic wall, post
or single gang electrical box.
Mounts to Viking VE-GNP Series gooseneck
pedestal’s with optional PROX-3-MK-GNP or
PROX-3-MK-VEGNP mounting kits
Designed for outdoor use, the PROX-3
comes standard with Enhanced Weather
Protection (EWP) (see DOD# 859)
PROX-3 is designed to meet IP66 Ingress
Protection Rating (see DOD# 859)
Pigtail connection for easy installation
Four red LED’s indicates power and flashes
off during card read
Transducer provides beep during card read
* Note: Read range tested with Viking PROXCARD or HID
ProxCard II and unit mounted on a non-metallic surface.
Model
Description
AES-2000
Accessible Entry System
202
AES-2005
Accessible Video Entry System
204
C-4000
Apartment/Office Entry Controller
164
ES-1
Stand Alone Keyless Entry System
193
VE-GNP
Series
Gooseneck Pedestals when used
with the PROX-3-MK-VEGNP or
PROX-3-MK-GNP mounting kits
424
DOD#
Specifications
Power: 5-16 DC (12V nominal), 300mA - average, 500mA peak. 120V AC/12V DC 500mA, UL listed adapter provided.
Dimensions: 216mm x 152mm x 25mm (8.5” x 6.0” x 1.0”)
Shipping Weight: 1.0 kg (2.3 lb)
Environmental: -40° C to 65° C (-40° F to 150° F) with up to
100% humidity
Connections: 18” long pigtail leads, 24 gauge
Credential Compatibility: Viking PROXCARD, PROXCARDISO, PROXFOB, HID (ProxCard II, ISO Prox II and ProxTag II)
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT (715) 386-8666
Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please:
1. Know the model number, the serial number and what software version you have (see serial label).
2. Have your Technical Practice in front of you.
3. It is best if you are on site.
RETURNING PRODUCT FOR REPAIR
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that needs repair:
1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)
number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individually boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:
Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.
4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The
customer MUST be able to step through recommended tests for diagnosis.
2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.
3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.
LIMITED WARRANTY
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manufactured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others.
NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAMAGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.
EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL
BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.
IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED
AS SUCH.
PART 15 LIMITATIONS
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Requirements
Cable Requirements: The PROX-3 can operate at up to *800 feet (244 m) of cable, using seven-conductor, shielded, stranded cable. Per the Security
Industry Association’s Wiegand specification, AWG 24 (such as Belden 9537) is the minimum gauge required for data transfer in a 500-foot run length.
However, the proper wire gauge to use must be determined by the current draw requirements of the reader, the length of the cable run, and the voltage
applied to the reader. If the reader is to be operated at 5 VDC, 5 VDC must be available at the reader (long cable runs have a voltage drop due to the
resistance in the cable). A larger gauge of wire (having less resistance) or a separate power supply near the reader may be required to ensure 5 VDC is
available at the reader.
Output Formats:
• Wiegand (industry standard 26-bit Wiegand)
• Magnetic Stripe (ABA Track II, clock and data, with card present)
Grounding: Shield (drain) continuity must run from the reader to the access panel. Shield (drain) and reader ground must be tied together at the access
panel and connect to an earth ground at one point.
Power: The PROX-3 may be powered by the access panel. As such, the reader is powered on when the access panel is powered on. However the best
case is to power the reader by a separate, linear power supply. A 12V DC 500mA power adapter is supplied with the PROX-3.
Voltage: 5 to 16 VDC Note: For maximum read range, a minimum of 12VDC is recommended.
FleaPowerTM Control Line: The PROX-3 can be placed in a special lower power mode by pulling the purple colored fleaPower Control Line low. This
special low power mode reduces the average power required by the reader.
* Note: When used with a Viking Entry System/Controller, see the Entry System’s Technical Practice for the maximum wire run length.
Installation
3.00
A. PROX-3 Mounting Specifications
1.0
6.00
Note 1: Read range is stated in a clean RF
and electrical environment using Viking
Proxcards presented parallel to the reader
surface with the reader operating at 12 VDC.
Additionally, read range may be affected by
local installation conditions. Range will be
less when mounted to metal.
0.92
Single gang electrical
box mounting holes
#6 screws, 2 places
Optional mounting
drill with 11/64" bit
for #6 screws,
4 places
6.44
8.60
Beeper
3.30
Note 2: Use of a linear power supply is
always recommended.
Note 3: Minimum current draw is obtained by
operating the reader in the fleaPower mode
at 5 VDC with the LED off. Peak current draw
occurs when reading a card or tag.
4.16
4.30
0.56
2.65
1.08
Approximate
Cable Location
B. Surface Mounting the PROX-3
The PROX-3 can be surface mounted to a non-metallic*
wall or post. The unit can be fastened with two screws (provided) to a single gang electrical box or directly to a wall or
post. For additional mounting strength, the four holes in the
outer corners of the PROX-3 can be drilled out with an
11/64” drill bit and fastened with four #6 flat head screws.
(2) 6-32 x 2" long
phillips screws
(included)
VIKING ©
MODEL PROX-3
* Note: The PROX-3 can be mounted to a metallic surface
but the proximity card read range will be dropped to
approximately ½ its normal distance.
Single Gang
Electrical Box
(not included)
** Important: After mounting and testing the card reader,
clean the front recessed area of the unit with rubbing alcohol and apply the provided label. Please note, the label is
permanent and not easily removed.
Model PROX-3
** PROX-3 Label
(included)
Optional (4) #6 x 2"
long flathead screws
( not included)
C. Mounting the PROX-3 to a Gooseneck Pedestal Using the PROX-3-MK-GNP Mounting Kit
Drill out the four holes in the outer corners of the PROX-3 with an 11/64” drill bit. Attach the PROX-3-MK-GNP mounting plate to the
Gooseneck pedestal with the four provided carriage bolts. Wire as shown in section E then fasten the unit to the mounting plate with
the 6-32 x 1.25” long flathead screws provided with the PROX-3-MK-GNP mounting kit.
* Important: After mounting and testing the card reader, clean the front recessed area of the unit with rubbing alcohol and apply
the provided label. Please note, the label is permanent and not easily removed.
VIKING
1/4"-20 x 1" carriage bolts
included with mounting kit
Model VE-GNP Gooseneck Pedestal
(not included) see DOD# 424
PROX-3-MK-GNP
Mounting Plate
1/4-20 Nylock nuts
included with mounting
kit, use with carriage bolts
Model PROX-3
(4) 6-32 x 1.25" long
5/64 hexdrive flathead
screws included with
mounting kit
©
MODEL
PROX-3
* PROX-3 Label
(included)
D. Mounting the PROX-3 and a Viking Entry Phone to a Gooseneck Pedestal Using the
PROX-3-MK-VEGNP Mounting Kit
Drill out the four holes in the outer corners of the PROX-3 with an 11/64” drill bit. Adhere the gasket provided with the Viking gooseneck pedestal, centering on the VE-GNP mounting plate. Fasten the PROX-3 to the mounting plate with the 6-32 x 1.25” long flathead screws provided with the PROX-3-MK-GNP mounting kit. The PROX-3-MK-VEGNP mounting plate can be mounted hoizontally or vertically to allow the PROX-3 to be postioned on the left, right, top or bottom of the entry phone with a VE-5x5 or VE-6x7
surface mount box. The plate can only be mounted on the left, right or top when using a VE-5x10 surface mount box. Attach the
PROX-3-MK-VEGNP mounting plate and the VE-Series (VE-5x5, VE-6x7 or VE-5x10) back box to the gooseneck pedestal with
the four provided carriage bolts. Wire as shown in section E. See the entry phone’s Technical Practice for wiring and mounting
instructions.
PROX-3-MK-VEGNP
Mounting Kit
Model PROX-3
* PROX-3 Label
(included)
VIKING
1/4"-20 x 1" carriage bolts
included with mounting kit
Channel for routing
PROX-3 wires
Gasket included with
model VE-GNP
©
MODEL
PROX-3
(4) 6-32 x 1.25" long
5/64 hexdrive flathead
screws included with
mounting kit
Model VE-GNP Gooseneck Pedestal
(not included) see DOD# 424
Gasket included
with mounting kit
* Important: After mounting and testing the card reader,
clean the front recessed area of the unit with rubbing
alcohol and apply the provided label. Please note, the
label is permanent and not easily removed.
1/4-20 Nylock nuts included with
mounting kit, use with carriage bolts
Viking VE-5x5, VE-6x7 or VE-5x10
back box (DOD# 424)
Wiring
When using the PROX-3 with any Viking Entry System/Controller, the provided 12V DC 500mA power adapter should be used. Follow
the directions below to prepare the power supply.
Step 1.
Step 2.
Step 3.
Connect power supply
wires to the PROX-3
power supply wires
Step 1. Cut off the barrel connector on the powersupply.
Step 2. Separate the wires.
Step 3. Connect the 12V adapter wires to the power supply wires on
the PROX-3.
(+) Black
(-) Black with
White Stripe
IMPORTANT: Do NOT plug in the
adapter until after Step 3 is completed.
Step 4. Plug in the power supply.
Connect to Typical Wiegand
Connections on Entry System
(Keep unused leads from shorting)
Connect to “-/Ground” on Entry System/Controller and Earth GND
Note: See “Cable Requirements” on page 2.
!
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the
telephone line. It is recommended that a surge protector be installed to protect against such surges.
Tr o u b l e s h o o t i n g
1. When the reader is powered up the LED’s will momentarily light amber, a victory beep (4-quick beeps) is heard and
then the LED’s will light Red.
2. Present the correct card and the reader will beep once and LED’s will momentarily turn off. It is up to the control panel
to control dual LED and have the LED turn green when an enrolled card is presented.
If reader does not recognize the card/tag (no beep, no LED flash) or reader has short read range, please see table below
for possible causes and solutions.
Possible Cause
Corrective Action
Incorrect wiring
Verify wiring connection
Not enough power
12 VDC suggested
Mounted near electromagnetic interference
Relocate or provide greater separation from
Incorrect card used
Verify card compatibility from model number
Reader/access panel not properly grounded
Quality Earth Ground needed. Verify shield line from the access panel to the
reader is one continuous, connected line.
Supply generating electromagnetic interference
Linear power supply recommended
If any of the corrective actions mentioned above don’t work, please disconnect the reader from panel and power it with a
separate power supply or 9V battery and test card functionality. By powering it individually and off the installation most variables that can cause malfunction are eliminated. If after the reader is powered by a separate power source the failure persist, please contact Viking Electronics Product Support.
Product Support Line...715.386.8666
Fax Back Line...715.386.4345
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
DOD# 228
Printed in the U.S.A.
ZF303200 Rev A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising